Search Documents

By John W. Lund

The Geo-Heat Center has been investigating the utilization of waste silica from the Cerro Prieto geothermal field for several years. The main objectives of the research were to com-bine silica with various additives to (1) form bricks for low cost housing, and (2) to produce a suitable road surfacing material. The various additives that were tested included hydrated lime, portland cement, plastic fibers, asphalt cement and emulsified asphalt. The silica-cement combination produced the strongest bricks and had the best weather resistance, whereas, the silica-lime combination produced the bricks with the lowest thermal conductivity and specific gravity density. The addition of plastic fibers to the silica-lime mixture improved both strength and weather resistance. The combination of asphalt and silica is not suitable as a road surfacing material, however, silica-cement appears promising.

Jan 1, 2006

By James P. Bennett, Jinichiro Nakano, Anna Nakano, Hani Abu El Hawa

Carbon feedstocks used in power, chemical and metallurgical industries typically contain numerous minerals or impurities that liquefy during high temperature processing to form slag as a byproduct. Slags have many industrial applications, for example, as construction materials and for element recovery. In addition to other variables, the extent of slag utilization is dependent on its com- position and post treatments. In this work, the in fluence of temperature and phos- phorus additions on phase evolution in coal slag was investigated. Synthetic slag mixtures with varying AlPO4 contents (0–14 wt%) were heated from 1380–1470 ° C in air, then water-quenched to preserve the phases formed. SEM/EDS, XRF and XRD analyses were performed before/after testing to gain insight about slag chemistry and phases present. It was found that coal slag exhibited a large solubility of phosphorous, affecting morphology of mullite formed under the conditions studied. Results obtained and their significance are discussed.

Mar 1, 2017

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By V. Blet

Rare earth elements (REE) are regarded today as highly critical raw materials but currently lack suitable recycling processes. A combined hydro- and pyrometallurgical process aimed at REE recovery from used NdFeB permanent magnets was recently developed by the CEA. The process integrates the physico-chemical treatment of magnets, followed by a solvent extraction step for the recovery and intra-REE separation using a selective extractant. A subsequent pyrometallurgical treatment via molten chloride salt electrolysis allowed the isolation of pure Dy metal. Technical-economic assessment and life-cycle analysis were also conducted. Following this first successful demonstration, a new project aimed at the recovery of REE from end-of-life nickel-metal-hydride batteries is currently being developed in association with industrial and academic partners. The project aims at evaluating from an experimental and economic perspective different processes converging at the production of value-added products such as cermet materials for catalytic applications, purified REO concentrates, or metallic alloys.

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By C. Peter Hayes

The world continues to change and with it the supply of minerals and metals, the location of centres of production of primary metal and the increasing levels of metals and materials recycling. New technologies are being developed to meet the ongoing search by industry for lower costs, cleaner production and new markets. To keep abreast with these changes, and to utilise fully, the potential benefits of these technical advances, the industry will need a professional workforce having different knowledge, skills and professional attributes than in the previous millennium. What are these skills and attributes? How to best attract and develop the metallurgists of the future, and provide for the ongoing educational and research needs of the industry?

By Timothy W. Ellis, John A. Howes, Roger D. Feldman

The new generation of more powerful, energy-intensive devices for communications, industrial production, energy storage and other purposes is creating new challenges to guard against environmental harm and protect national security. Many devices are designed, used and disposed of in a linear, rather than circular manner. This causes scientific, legal and economic issues because the life-cycle costs of components are not adequately considered. Dealing with these issues in isolation from each other can lead to unintended consequences. New models to confront these issues are being defined. This paper suggests a fundamental tool for dealing with material science issues while taking into account the engineering, economic and policy perspectives. That tool is the development of a true, levelized cost of energy storage model with a wide spectrum of inputs for comprehensive analysis. This paper will discuss inputs and the process which can yield meaningful, useful comparisons among batteries and energy-intensive products.

Mar 1, 2018

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By Antoine Allanore, Luis A. Ortiz, Donald R. Sadoway

"The steelmaking industry has drastically reduced its energy consumption in the last fifty years, and today’s technologies are considered to operate at their optimal efficiency with respect to energy needs. To cope with new constraints related to greenhouse gas (GHG) emissions, a change of paradigm is necessary. One of the promising technologies that could be deployed to help reach CO2 mitigation targets relies on the intensive use of electricity: molten oxide electrolysis (MOE). This paper presents the key process parameters that need to be tuned to address the practical needs for both high productivity in a steelmaking reactor and for an energy efficient process. Herein we show that contrary to common perception, the electrolysis process for ironmaking requires less energy than today’s chemical reduction route. Furthermore, we prove that most of the energy that must be provided to operate the electrolytic iron production cell is thermal energy which is readily generated by joule heating during electrolysis due to large currents being passed through the electrolyte. The energy consumption of the electrolysis cell is therefore shown to be highly dependent on the cell configuration and the chemistry of the electrolyte. As a consequence, the CO2-impact of the technology strongly depends on both the power production mode and the technological choices for design of the process, including cell configuration. Surprisingly enough, even when the electricity generation is not carbon-free, MOE still appears to be viable from the perspective of reducing GHG emissions providing sound reactor design considerations are made.IntroductionIn the context of greenhouse gas (GHG) emissions mitigation, the steelmaking industry is considering several techniques that could sustain the efforts and progress achieved by this sector in the last decades [1]. A recent report [2] on potential routes for low-CO2 steelmaking highlighted for all techniques both the strong dependency of CO2 emissions on electric power production mode and the need for a decrease in energy consumption per tonne of steel. Incited to innovate with respect to this last criterion, the steel industry considers electrolysis to be a promising technological solution, and in particular the molten oxide electrolysis (MOE) process. This process conducts electrolysis in a mixture of oxides that dissolve the iron oxide feed, which by the action of electric current is decomposed into liquid iron and oxygen gas. The opportunity for reduction in energy consumption during steelmaking by MOE is commonly attributed to the “direct” pathway from iron oxide to liquid metal offered by the use of a molten oxide melt and operation at a temperature above the melting point of iron, ideally 1600°C, to provide enough superheat for tapping the molten iron product:"

Jan 1, 2011

By Bien Ferrer

In most smelting operations, there is a strong incentive to improve safety, reduce downtime and extend the campaigns of furnaces and related equipment. An asset management strategy that is based on information, rather than simple throughput metrics and intuition, can be developed to improve uptime and unlock value currently unrealized at existing smelters. Advances in digital technology, including data analysis, modelling and monitoring for hot pyro-metallurgical vessels, make it possible to assess the current condition of an asset, as well as to make more informed projections about its future condition, using on-line and historical data. This would allow practices around asset management to be more proactive and less reactive, with the end-result of optimized uptime. ‘Digital Asset Management’ describes a concept in which digital technology is used to support an asset management strategy and accelerate decision-making by providing information on what, why and how an asset should be designed, operated or maintained. With the overall goals of effective resource utilization, optimized operations, capital efficiency and social acceptance, Smelter 4.0 is a program of holistic improvement and is underpinned by the effective use of data to drive decisions. This paper focuses on Asset Reliability, which is one of the improvement pillars of Smelter 4.0, and introduces a methodology that is aimed at closing the gap between recorded data and evidence-based decision-making through Digital Asset Management.

By Alistair Burrows

Situated in the oblast of East Kazakhstan, the Ust-Kamenogorsk Metallurgical Complex has spent the past twenty years renovating and remodelling itself as a modern polymetallic sulphide smelting facility, and a regional centre of excellence for custom smelting. Along the way there have been changes to the company structure, introduction of new technologies, investments in expanded capacity, environmental improvements, and addition of new metal products and by-products to the site’s repertoire. These changes have been gradual and incremental, but taken together they represent a significant contribution to placing Kazakhstan’s sulphide smelting industry on a strong foundation for enduring success in the international custom smelting market. In achieving these changes, a workforce that was historically isolated from much of the world now has recognised expertise, internationally competitive skills, and confidence to embrace the future. Further improvements in energy efficiency, environmental compliance and polymetallic processing capabilities are challenges that UKMC stands ready to face.

By D. Q. Cang, G. Duan, H. X. Li, H. Bai

"Life cycle assessment (LCA) is a valid environmental evaluation method and enterprise environmental management tool used in industrial ecology areas. In this paper LCA was newly used to evaluate the environmental impact of manufacturing of alumina by Bayer process in china from two aspects of logistics and energy flow, GaBi software acted as analysis tools with evaluation model established, and several environmental impact assessment criteria were selected based on the actually typical date of Bayer alumina producing process. Evaluation results show that alumina manufacturing by the Bayer process has a great impact on the global warming and human health of respiration, even roasting process gives rise to the greatest impact of winter fog index. Scenario analysis proposed ways of reducing environmental load caused by Bayer process including: (1) the economic and efficient use of mineral processing technology; (2) optimization of energy use, saving power consumption or the use of new more economical source of energy; (3) actively promote the use of innovated technology and equipment in alumina manufacturing and waste such as red mud utilization process.1 IntroductionSince 2002, China is already the world's biggest producer of aluminium, in 2007, China aluminum production has accounted for above 1/3 all over the world, 2009 for 13 million tons and to the end of 2010, China aluminum production is expected increased to be over 15 million ton [1,2,3]. While as the raw material for producing aluminum the alumina production in china has up to 19.46 million tons of the world's total quarter in 2007, by the end of 2009 China alumina production has achieve to 23.78 million tons [4,5]. China has rich bauxite resources with proven reserves about 23 million tons, but the great majority of china bauxite is hard monohydrate diaspore type with low ratio of aluminium silicon, high impurity content and poor aluminum dissolution performance, that cause high energy consumption, long and complex process, high production costs and heavy environment load[6,7]. Before most used alumina production was sintering process rather than Bayer method in china, over the past decade Bayer method has been widely applied instead of sintering process or combination both forming joint process, premise is improving bauxite quality by mineral processing or adding imported rich bauxite mineral[6,8]. In general each ton production of alumina needs bauxite 1.6~2.20t, limestone 0.7~1.7t, soda 0.250kg, fresh water 12.30 cubic meters, in addition to consume large amounts of energy, and emission waste water over 8.0 cubic meters, dust 2.3~5.7 kg, red mud 0.8-1.5 tons. In china Red mud yield nearly 30.0 million tons every year, accumulated stock is approximately 0.2 billion tons, by 2015 accumulative total red mud is expected to reach 0.35 billion tons [9-13].We know aluminium industry and alumina production have produced large waste, make large energy consumption and its environmental impact could not be ignored. Expecting to optimize production processes and achieve resource recycling for this industrial process the proper environmental assessment is very necessary. Currently Life Cycle Assessment (LCA) is generally recognized as the approved tool to achieve the purpose. The essence of LCA tool is to examine, identify and evaluate a kind of materials, product, process, or a system of environmental impact in their whole life cycle. The life cycle of materials or products includes whole process from raw materials obtained to the final disposal, or more ideal with original or other forms of the whole process of recycling [14-17]."

Jan 1, 2011

By G. Nazari

ERAMET, through its subsidiary COMILOG, have rights to a rich niobium and rare earth deposit inGabon. The Mabounié deposit, is located 50 kmfromthe town of Lambaréné, in a fairly remote location. ERAMET has been developing a process to recover value metals for several years, and approached Hatch Ltd. to design a sizeable Demonstration Plant to help them further optimize the process, and prove the flowsheet is technically viable. The process employs concentration techniques to recover an upgraded Nb/REE feed material for processing in the subsequent leach step. Rare earths and niobium are selectively leached, and subsequently precipitated. Following precipitation, rare earths undergo bulk separation and are purified to produce LRE and mixed MRE/HRE products, which will be further processed by Third Parties. This paper provides a high-level overview of the process, summarizes the motivation for a Demonstration Plant in the vicinity of the deposit, and discusses technical challenges faced during the flowsheet definition and design phase. Key challenges are focused on and summaries of the methodologies used to address each challenge, as well as the solutions to overcome the challenges, are discussed. The paper provides motivation for further process simplification and concludes with a project update.

By V. R. Voller

"The World Wide Web (the web) provides a very useful resource for the enhancement of teaching and research dissemination. This paper advocates that researchers take control of this resource and become actively involved in creating web content. Two examples of the use of the web in a materials setting is provided. The first illustrates how a concept quiz for teaching can be developed. The second shows how a materials processing model can be run in real time over the web. The paper closes with a summary of some resources that can be used to create web materials.IntroductionA recent copy of a newspaper advertisement read""Share what you know, learn what you don't""This neat phrase sums up a powerful teaching and research philosophy. In an educational setting a prime motivation for research is to uncover the unknown and venture in directions previously uncharted. The balance to this search for knowledge should be a desire to share that knowledge with others; whether it be with students in the classroom or research colleagues in a wider setting.The .World Wide Web and its associated multi-media software offer a perfect platform for researchers to share their knowledge with an extremely wide sector of the research community. To enable the use of this resource researchers must take the power that the web offers them into their own hands and create products that take maximum advantage of the medium. It is key that researches at the forefront become directly involved, otherwise a potential powerful medium will not realize it's true potential, and colorful products with no core content will proliferate. The object of this paper is to outline two ways in which the web can be used to enhance teaching and research objectives."

Jan 1, 2000

By Susumu Nagae, Hajime Ikeda

Recently, a number of mine development projects have been setback by social, economic and, environmental circumstances that had not been seen before. Many of these problems do not always originate from direct mine pollution. Typical examples of these are· conflicts between the exploration company and the local residents, sudden objections just before the development is to begin, and unexpected tightening of environmental regulations. The common background to these problems is expanding global environmental awareness. This includes complex factors ·such as the expansion of exploration to remote regions, the brisk activities of environmental NGOs, the increase of international environmental laws and, governmental policy changes. Today, the range of issues concerning mine development is widening significantly. The participation of local residents arid NGOs in the development planning, together with the company and government, has become essential for smoothly carrying out mine projects and making them more beneficial for stakeholders. Introduction The common image of the environmental problem with respect to mining is direct mine pollution, such as the collapse of tailings dams, pollution from refineries, and acid mine drainage. All over the world, the mining industry has made large investments in capital and technology to solve and prevent mine pollution, and these efforts have been making steady achievements. However in recent years, new cypes of environmental problems which are not originating directly from mine pollution are emerging frequently. Most of the problems are concentrated at the exploration stage to early stage of development, which have less impact on the environment. In the worst case, mining project may be forced to cancel and could cause serious damage to the industry because they could not collect their investment. I would like to take a general view of the examples of new types of trouble, their characters, background, and strategies against these problems.

Jan 1, 2000

By Mark William Kennedy

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Jan 1, 2014

By Cassandre Nowicki, Louis Gosselin, Carl Duchesne

"Quebec's primary aluminium production industry consumes roughly 39 TWh of electricity per year and is accountable for roughly 7 million tons of CO2 equivalent. By tapping only a small portion of waste heat and integrating it inside the production facility itself, we can significantly reduce GHG emissions and energy consumption. Although the amount of thermal waste can be adequately estimated by applying an energy balance to production processes, this provides very little information on the quality of waste heat and its potential for integration. A measure of exergy is required. Waste heat streams characterized by high exergy content may generally offer valuable incentives for recovery and integration. More generally, exergy values limit integration possibilities. An exergy analysis is provided for the aluminium electrolytic reduction process. This is meant to guide future heat recovery initiatives and energy efficiency measures.IntroductionCanada is one of the world leaders in primary aluminium production and 92% of its aluminium production capacities are located in the province of Quebec. In 2007, production capacity reached 2,786,000 tons in Quebec alone. Since it is estimated that 2.5 equivalent tons ofCO2 are released for each ton of aluminium produced in Canada, Quebec's aluminium production industry is accountable for roughly 7 million tons of CO2 yearly [1, 2]. Furthermore, with an average electricity consumption of 14 MWh per ton, primary aluminium accounts for 39 TWh of electricity per year in Quebec and this energy consumption represents 350 thousand tons ofCO2 equivalent [3, 4]. Natural gas consumption associated with primary aluminium production accounts for less than 1 TWh, but it represents an additional 350 thousand tons of CO2 equivalent [ 4].This work is meant to provide a tool to guide future efforts towards heat recovery and energy efficiency in the primary aluminium industry. Waste heat recovery and thermal integration can cut down both energy consumption costs and GHG emissions. In a primary aluminium production facility, waste heat represents roughly half of the energy input into the Hall-Heroult process. Tapping only a small portion of this energy could reduce natural gas and electricity consumption significantly. In order to evaluate how much of this energy is actually usable, we propose to apply an exergy analysis to individual transformation processes in an aluminium production facility, such that a potential to do work can be assigned to every waste heat flux. The approach will be described in the next section."

Jan 1, 2012

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

The oxygen blast furnace is a new technology for ironmaking, where the oxygen and CO2-stripped blast furnace top gas are blown into the blast furnace replacing the conventional hot air. The oxygen blast furnace could reduce the consumption of coke and emission of carbon dioxide. In this chapter, a three-dimensional numerical model was developed to simulate the lance-blowpipetuyere-raceway region of a blast furnace, and the flow and combustion behaviors of coal particles were investigated based on an oxygen blast furnace. Compared with the traditional blast furnace, the combustion characteristics in the raceway of the oxygen blast furnace were different. In addition to the combustion of coal and coke, the combustion of large amounts of reducing gas was included. The coal combustion of different oxygen content (70, 80, 90, 100%) were investigated. The simulation results indicated that the coal burnout was only 21.64% at an oxygen content of 70%, a decrease of 51.52%, compared with a traditional blast furnace. The coal burnout was increased with the increase of oxygen content. When the oxygen content is 100%, the coal burnout was 90.38%, an increase of 17.22%.

Mar 1, 2017

By Krishna Parameswaran

This paper illustrates sustainability considerations in copper hydrometallurgy using examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission development of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper hydrometallurgical processes can be sustainable. The examples used to illustrate sustainable development and related concepts include: water conservation opportunities in milling and leaching operations; implementing green chemistry and promoting product stewardship in the electrorefining of copper.

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997