Search Documents

Primary sulphidic gold ores in the Archean provinces of Western Australia can be broadly sub-divided into pyritic, pyrite-telluride, arsenical and antimonial types. Pyritic ores contain only native gold, and are essentially not refractory. Arsenical ores almost always carry some invisible gold, and may vary from mildly to highly refractory. Pyrite-telluride ores contain gold-bearing tellurides, and are refractory to varying degrees. Antimonial ores usually contain aurostibite, and may be very difficult to process. A classification scheme for metallurgical processing, based on mineralogy, is proposed for the ores, and implications for processing are discussed.

Jan 1, 1995

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Vahid Javaheri, David Porter, Tun Tun Nyo

A field emission scanning electron microscope equipped with EBSD has been employed to evaluate the role of 0.013 wt% Nb on the evolution of the microstructure and texture of a novel thermomechanically processed low-alloy, medium-carbon steel. Specimens were subjected to hot-rolling with a total reduction of 80%, four passes in the recrystallization regime and four passes below the non-recrystallization temperature. Immediately after rolling, the strips were quenched to 420 °C and subsequently cooled slowly in a furnace to simulate strip coiling with transformation of austenite to bainite. The results showed that Nb microalloying results in a finer microstructure with a sharper texture when compared to an identical steel but without Nb. In addition, analysis of the retained austenite texture indicated that the main bcc texture components are the product transformed brass and copper components in the parent austenite.

Mar 1, 2018

By C. P. Snyman

Three independent methods of coal classification can be distinguished, namely on the basis of grade, type and rank. The latter two can be determined accurately and unambiguously only by means of microscopical techniques. These three independent variables affect all the coal properties and therefore also the technological behaviour of a particular coal. The influence of the inorganic constituents of coal on the fusibility of the ash and on the length of the slag, and also on fouling and slagging, is discussed. The fractionation of the ash-forming constituents during combustion and gasification of pulverised coal shows that fouling and slagging are not related directly to the fusibility and composition of ash of the coal as a whole. The results of combustion experiments using a drop furnace technique indicate that the ignition temperatures of the light volatiles in the coal, and of the formed char, as well as the burn-out time of the char are more dependent on the rank than on the type or grade of the original coal. High-ash coals, however, apparently ignite at lower temperatures and are more reactive than low-ash coals of similar type and rank. The surface properties of coal, which are important in froth flotation and oil agglomeration, correlate well with the inherent moisture content (and by inference with the heat of wetting and the calorific value) and therefore with the type and rank of the coal. In coal exploration, variations of rank offer the possibility of predicting the presence of an intrusion near the seam, thus contributing to more effective exploration and mine planning.

Jan 1, 1991

By M. A. Gimenes

The utilization of chlorination in extractive metallurgy and advanced ceramics areas has been widely investigated as a preparative route in order to obtain intermetallic compounds, which are used as precursors in the development of new materials and process. The major processes of decomposition of rare-earth ores use sulfuric acid and sodium hydroxide at high temperatures, however there is not much work concerning chlorination. In this work, a systematic study of the reaction between xenotime (REPO4), chlorine and carbon has been performed. Particular emphasis was on kinetic studies to establish optimized conditions for the reaction. The kinetics of chlorination of xenotime raw material by rare-earth elements/compounds has been studied over a temperature range from 600°C to 950°C. The influence on the rate of conversion of xenotime to RECl3 on temperature, partial pressure of chlorine, carbon content, and particle size were investigated. A global rate equation that includes these parameters has been developed. The results show that the process follows the unreacted core-shrinking model with a formation of a porous product layer. The powder X ray-diffraction technique corroborated this model showing clearly the patterns related to the formation of yttrium oxychloride (YOCl), indicating that the reaction mechanism involves the presence ofan intermediate step before the formation of lanthanide chloride.

Jan 1, 2000

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By Sheng-li Wu, Guo-liang Zhang, Bo Su

One of the major challenges for the Canadian Gen IV Super-Critical Water-cooled Reactor (SCWR) concept is the selection of fuel cladding materials. The Canadian SCWR concept will operate at a core outlet temperature of 625 oC and 25 MPa of pressure with peak cladding temperature reaching as high as 800 oC. Corrosion resistance is an important factor for material selection. Austenitic stainless steels that contain Cr contents greater than 18 wt.% are generally considered to provide adequate corrosion resistance. In this work, the pressure dependence of the corrosion of austenitic stainless steel 310 containing 24 wt% Cr is assessed at 625 C for exposures of 1000 hours to evaluate the suitability of superheated steam as a surrogate for supercritical water at 25 MPa. Transmission Electron Microscopy (TEM) revealed that 310 exposed to different pressure conditions at 625 oC. (i.e., 0.1, 8 and 29 MPa) had generally the same type of the oxide structure, i.e., a Cr-rich oxide with the spinel structure on outer surface adjacent to the water phase. The material exposed at 8 and 29 MPa had a double layer oxide structure, with the outer oxide layer having a much larger grain size, while the samples exposed at 0.1 MPa showed only a single spinel-phase oxide layer. Cr-depleted recrystallized austenite grains were found underneath the spinel phase oxide. The adjacent large-grained austenite substrate had M23C6 carbides in the grain interior. The implications of these results are discussed.

Jan 1, 2015

By D. M. Jones

Dust generation data have been obtained from 19 industrial Outokumpu flash furnaces. Statistical analyses of the data have been carried out and the most significant factors affecting dust generation evaluated. The results indicate that dust production may most effectively be minimized by: 1) Minimizing the distance between the molten slag and the furnace roof 2) Optimizing burner design and combustion parameters.

Jan 1, 1996

By C. A. Nogueira, F. Margarido

"A research work has being carried out annmg at evaluating the possibility of treating simultaneously several electrochemical systems of spent batteries using the same process, in order to overcome the high costs and difficulties of selective collection and sorting. Zn-Mn02 systems, representing more than 75% of portable battery market, shall be treated in dedicated processes. The treatment assessment using a single hydrometallurgical process of the other major systems (NiCd, NiMH and Li-ion), having Ni and Co as main metals, was the aim of the research work here reported. Sulfuric acid leaching was demonstrated to be adequate for dissolving more than 90% of the metals of interest contained in batteries. The subsequent separation of metals by solvent extraction, using organophosphorous extractants like DEHPA and Cyanex 272, allowed the production of pure solutions of rare earths, cadmium/manganese, cobalt, nickel and lithium, enabling their further recovering.IntroductionRecycling is the best approach for end-of-life management of spent batteries mainly by environmental reasons but also motivated by resources conservation and, in some cases, by economic profits. Most relevant electrochemical systems of portable cells are Zn-Mn02 (ZMB, alkaline and saline), nickel-cadmium (NiCd), nickel-metal hydride (NiMH) and lithium-ion (LIB). These batteries are collected, sorted and usually treated separately, applying for pyrometallurgical or hydrometallurgical technologies, the former being the most common.Several processes have been developed and some of them industrially applied, as described in some available review papers [l, 2]. In Europe for ZMB systems the oldest processes are Batrec [3] and Citron [4]. Although having differences in details, both are based on pyrometallurgical recovery of zinc by distillation, in metallic or oxide forms, being manganese retained in the slag together with iron. Hydrometallurgical alternatives are also available, like Zincex [5] and Recupyl [ 6] processes, both using sulfuric acid solutions as leachant. The application of the existing technologies to battery recycling, instead of using dedicated processes, is other alternative already tested, being the Waeltz furnace or the Imperial Smelting some examples."

Jan 1, 2012

By Norihiro Murayama

Syntheses of zeolitic materials were carried out from coal fly ash by alkali hydrothermal treatment as part of the reuse and recycle technologies of coal ash, For the obtained zeolites, the cation exchange capacity and acid resistance, which are very important in the practical use of cation exchanger in aqueous solution, are investigated during this stufY, The cation exchange amounts of the NaP, CaP and K-CHA zeolites are measured for various cations such as K+, Na +, NH4+ Ca2+, Mg2+, Pb2+, Cd2+ and so on. The change in crystallization degree are researched as a function of pH. The simultaneous removal ability of NH4+ and PO43- in solution is examined for an example of the water purification with CaP zeolite. From these results, the characteristic and its mechanism of cation exchange are clarified for the various zeolitic materials obtained from coal fly ash.

Jan 1, 2003

By M. L. Cunha

The lack of control of As and Sb compounds from copper smelters and converters has rendered some chalcopyrite containing arsenopyrite, stibnite and tetrahedrite minerals unusable for metal extraction. In the present investigation, we have studied the carbothennic reduction of Portuguese chalcopyrite mineral concentrate in the presence of lime/CaS04 and CaS04/Si02. Thermodynamic equilibrium calculations were performed to study the distribution of As and Sb between metal and the CaO-Si02-FeO slag phase. The phase equilibrium calculations also show the effect of oxygen partial pressure on the increase in the volume of the slag phase, which helps in lowering the copper metal formation temperature and facilitates a better separation between metal, matte and slag. The reduction reaction kinetics was studied between 850°C and 1100 °C, and the phases formed were identified by X-ray powder diffraction and scanning electron microscopy techniques. The importance of this research for using recycled matte, lean and rich minerals with As and Sb is also explained.

Jan 1, 2001

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off....,gases from the copper ?and nickel flash smelting furnaces and converters? in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are presented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas.and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off-gases from the copper and nickel flash smelting furnaces and converters in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are pre¬sented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

The oxidation of zinc vapour plays a very important part in the operation of the Imperial Smelting Process. The kinetics of the reoxidation of zinc vapour by carbon dioxide and water vapour onto quartz and zinc oxide substrates is qualitatively understood and this pertains to the conditions found as the gases are being transferred from the furnace to the splash condenser. However, re-oxidation also occurs in the shaft of the furnace where the solid substrates are sinter and metallurgical coke. It was found that there was a threefold increase in the rate of oxidation on sinter, compared to quartz and a 30 to 300 increase in rate on the coke. This was attributed to the high surface area offered by these materials.

Jan 1, 2003

The oxidation of zinc vapour plays a very important part in the operation of the Imperial Smelting Process. The kinetics of the reoxidation of zinc vapour by carbon dioxide and water vapour onto quartz and zinc oxide substrates is qualitatively understood and this pertains to the conditions found as the gases are being transferred from the furnace to the splash condenser. However, re-oxidation also occurs in the shaft of the furnace where the solid substrates are sinter and metallurgical coke. It was found that there was a threefold increase in the rate of oxidation on sinter, compared to quartz and a 30 to 300 increase in rate on the coke. This was attributed to the high surface area offered by these materials.

Jan 1, 2003

By Richard B. Diver, Mark D. Allendorf, Daniel E. Dedrick, James E. Miller, Roy E. Hogan, Andrea Ambrosini, Eric N. Coker, Anthony H. McDaniel, Nathan P. Siegel, Gary L. Kellogg

"Converting carbon dioxide and water to hydrocarbons is an attractive option for storing solar energy and, coupled with appropriate CO2 capture technology, for recycling carbon and impacting atmospheric CO2 concentrations. For any process, high solar-to-fuel efficiency is necessary for large scale viability and favorable economics. Thermochemical approaches for solar-to-fuel conversion are potentially highly efficient as they avoid the inherent limitations of photosynthesis and also sidestep the solar-to-electric conversion necessary to drive electrolytic reactions. Solar-driven two-step metal-oxide-based thermochemical cycles for producing the components of syngas, CO and H2, from CO2 and H2O are the basis of the “Sunshine to Petrol” project. Multi-cycle production of both H2 and CO has been demonstrated over several iron- and cerium-based compositions fabricated into monolithic pieces both in the laboratory and at the National Solar Thermal Test Facility. These compositions are being developed for deployment in a unique and continuous solar-driven reactor prototype, the counter-rotating-ring receiver reactor recuperator or CR5.IntroductionThe interconnected challenges posed by increasing global competition for petroleum and the increasing concentration of atmospheric carbon dioxide are now widely recognized. Meeting these challenges requires recognition that although hydrocarbon fuels are ideal energy carriers, they can no longer be thought of as primary energy sources. It is necessary to take the realistic view that our conventional fossil fuels are in fact “stored sunlight” in the form of “sequestered carbon.” This view leads to a search for options to use and store sunlight more directly.Sunshine to PetrolIn combusting hydrocarbons we unlock the energy for utilization, but we also release the carbon to the atmosphere. However, nature teaches us that with an appropriate persistent energy source, e.g. solar irradiation, it is possible to effectively reverse the combustion process and “reenergize” CO2 and H2O back into hydrocarbon form."

Jan 1, 2010

By Jason H. Nadler, Jason A. Kulpe, Stephanie J. Lin

"A numerical method has been developed to predict the microstructural characteristics of reticulated metal foam. The porosity of this foam is derived from sacrificial template particles of known particle size distribution, which are incorporated with other precursor components. In this approach, a porous structure is numerically generated starting with Powell's sphere packing algorithm. The resulting stochastic structure has characteristics similar to those of corresponding metal foam. Deterministic inter-sphere connections are calculated to more accurately model the pore morphology that evolves during thermochemical synthesis. Estimations of pore morphology and specific surface area of the simulated material are compared to lab-synthesized materials composed of equivalent constituent compositions. In addition, the effect of template particle size, inter-sphere connections, and the geometric constraints on pore morphology and permeability are investigated to refine microstructural evolution and design.IntroductionReticulated foams, characterized by their interconnected pore network, can be obtained by incorporating spherical sacrificial template particles into precursor materials followed by template removal processes. The resulting structure is composed of contiguous spherical pores whose morphologies reflect those of the original templates. Based on some of the unique features of this synthesis approach, a methodology is introduced in this work whereby these foams are digitally constructed using experimental data from the template particle sizes and precursor formulation. Digitally constructed porous structures can then be compared to their laboratory synthesized counterparts through the quantification of structural features such as porosity and surface area per unit volume, which in tum are used to inform the foam's fluid transport propertiesThe spherical template particle packing algorithm developed here is adopted from Powell's work [1], which also includes approaches to obtain percolation and density in random packings [2]. Gervois gives a mathematical development for the stereological sectioning of packed hard spheres [3]. Stereological sectioning facilitates determination of relevant three dimensional morphological properties from two-dimensional data [4]. Studies on the sphere distribution size and the related particle packing density and coordination number results are studied in [5, 6]. Lastly, Kato describes a sintered neck structure, which is used with these packings [7]. This neck structure, as a model of the particle shape following heat treatment, is implemented here in a similar manner. A strong difference between the available literature and the methodology here is that spheres are packed to ultimately represent porous space, not rigid solid space."

Jan 1, 2011

By H. Y. Sohn

The purpose of this article is to analyze critically and quantitatively the effect of chemical equilibrium on the overall rates of fluid-solid reactions. It is shown through a mathematical analysis that a reaction with a small equilibrium constant (a positive standard free energy of reaction) is more likely to be rate-controlled by pore diffusion or mass transfer than a reaction with a large equilibrium constant. The overall reaction rate of the former also tends to be slow. Furthermore, the apparent activation energy of such a reaction approaches the standard enthalpy of reaction (M-f'), rather than the true activation energy of the chemical reaction. The Law of Additive Reaction Times developed by the author is shown to apply to equilibrium-limited fluid-solid reactions and to be useful in quantitatively analyzing the behavior of such reactions.

Jan 1, 2003

By H. Y. Sohn

The purpose of this article is to analyze critically and quantitatively the effect of chemical equilibrium on the overall rates of fluid-solid reactions. It is shown through a mathematical analysis that a reaction with a small equilibrium constant (a positive standard free energy of reaction) is more likely to be rate-controlled by pore diffusion or mass transfer than a reaction with a large equilibrium constant. The overall reaction rate of the former also tends to be slow. Furthermore, the apparent activation energy of such a reaction approaches the standard enthalpy of reaction (Mf'), rather than the true activation energy of the chemical reaction. The Law of Additive Reaction Times developed by the author is shown to apply to equilibrium-limited fluid-solid reactions and to be useful in quantitatively analyzing the behavior of such reactions.

Jan 1, 2003