Search Documents

By Gang Qi

The solubility of nitrogen in pure molybdenum was measured over the temperature range 2173 to 2473 K and up to one atmosphere (101 kPa) of nitrogen gas pressure. Both thermochemical and kinetic aspects of this phenomenon were considered in this study. The solution of nitrogen in molybdenum may be expressed by the reaction 1/2N2(g) = {N} (Mo,s), for which the standard Gibbs energy is given by the expression {A}G° = 78,500 + 27.36T Joules/g atom N. The formation of molybdenum nitrides, specifically Mo2N, was considered. Attention was also focused on the mechanism of nitrogen solution in molybdenum. Estimates of the diffusivity of nitrogen atoms in solid molybdenum were derived from the kinetic data.

Jan 1, 1991

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By M. L. Sorokin

The thermodynamic of nickel production from laterite ore and from sulfide concentrate can be analyzed using PO2 - PS2 diagram of the Ni-Fe-S-0-SiO2 system. The procedure of the diagram computation is suggested and the diagrams for various temperature and Fe/Ni ratio are calculated. Three-suffix Margules equations are used for the calculation of the thermodynamic properties of three solutions: liquid matte, liquid slag and solid Fe-Ni alloy. The diagrams are used for the considerations about direct one-stage metallic nickel production.

Jan 1, 1994

By Joni M. Barnes

A strain of Pseudomonas stutzeri isohted from selenium contaminated surface waters, was found to be effective . in reducing selenate (Se04 2) stoichiometrically to selenite (Se03 2 '), which was further reduced to elementaJ selenium (Se0 ). These reactions were concurrent with the microbial oxidation of lactate. In order to assess quantitatively the amounts of seilenate and selenitein solution, improvements to existing analytical methods (ion exchange chromatography and inductively coupled plasma atomic emission spectrophotometry technique) .were made.

Jan 1, 1991

By Kenneth S. Coley, Michael Pomeroy, Elaine Chen

Recent work on modeling of BOF steelmaking is reviewed, highlighting the critical aspects of each approach. It is concluded that the most successful models should be based on a deep understanding of the mechanisms and kinetics of the critical reactions. The importance of the decarburization mechanism is discussed with particular reference to its role in droplet swelling or bloating which has a profound influence on the droplet residence time in the slag. Conditions which cause bloating are discussed and the rate determining step is proposed to be primarily nucleation of CO bubbles inside the metal droplet with some influence from growth by reaction at the bubble/metal interface. The discrepancy in the super-saturation ratio required for classical nucleation is discussed and an approach using a surface tension modifying parameter is illustrated. Finally, the role of CO nucleation in controlling the driving force for dephosphorization is discussed.

Jan 1, 2014

By G. W. Barton

Process Systems Engineering (PSE) can be defined as the integrated usage of computer-based design and analysis tools. As such, PSE is becoming increasingly important in the chemical and petrochemical industries. This paper shows how a range of PSE techniques have been applied to the zinc electrowinning process. Topics discussed include model development, parameter estimation, steady-state and dynamic model applications, steady-state optimisation and neural network modelling.

Jan 1, 1994

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By Claudio Toro, Alex Moyano, Jonkion Font, Carlos Caballero, Pedro Morales

"Codelco-Chile in the last decade has carried out industrially-oriented research as an alternative to the traditional batch-type converting process. In a first stage carried out preliminary evaluations in a rearranged Peirce Smith (PS) converter, and then an exploratory test in a “Convertidor Teniente” (Teniente converter, TC) for the Codelco-Chile Continuous Converting Process. However, the validation test for this process in the TC was delayed up to the second quarter of 2007 where the validation studies were done satisfactorily.Thus, the objective of this paper is to present the results of the campaign tests validating the Codelco-Chile Continuous Converting Process in the TC1 of the Codelco Norte smelter.The results of charging the solid or liquid matte or high grade matte (“white metal”) by Garrgun, or by mouth of the 22 m x 5 m TC1 are presented. Some features of the industrially validated process are discussed, and the pilot test results of the matte injection are also presented."

Jan 1, 2009

By Benjamin P. Hay

Complexation of a metal ion to a ligand often results in structural changes that introduce steric strain within the ligand. A design criterior:1 for ligands that will complex metal ions more strongly is to choose Iigar:1d architecture, that minimizes this strain. This paper describes how molecular mechanics models can be used to define the degree of ligand binding site organization in terms of' ,strain energies associated with conformational reorganization and distortion of the binding conformer. This approach yields a method to predict how modifications to ligand structure will affect metal binding affinity.

Jan 1, 1999

By James C. Foley

In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ monitoring of acoustic amplitude and velocity as sintering proceeds. Samples were made from elemental powders of Al (99.99%), Al (99.7%), Ag, (99.99%), Cu (99.99%) and Fe (99.9%). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and amplitude during sintering. The changes in acoustic properties were correlated with mechanical properties. Evolution of a series of reverberating echoes during sintering is shown to provide information on the state of sintering, changes in sintering kinetics as well as having the potential for detection of interior flaws.

Jan 1, 2001

By John A. Herbst, William T. Pate

"Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen, and the coordination of all unit operations in pursuit of the highest performance level. However, several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of unit operations to account for critical interactions within and between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significaritly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated with the models and can be effectively optimized. Financial goals seems to be the objectives of choice.This paper discusses recent progress in overcoming the challenges and illustrates a promising approach which is being pursued at Mexicana de Cobre's La Caridad copper ore concentrator. At M de C, advanced control strategies have been installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, increased from 76,000 tpd to 90,000 tpd. Plantwide integration is expected to gain an additional 3% improvement in profitability."

Jan 1, 1996

By John A. Herbst

Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen and the coordination of all unit operations in pursuit of the highest performance level. However several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of Unit operations to account for critical interactions within and 'between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that 'knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significantly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated With the models and can be effectively optimized. Financial goals seems to be the objectives of choice. This paper discusses recent progress In overcoming the challenges and illustrates a promising approach which is being pursued at :Mexicana de Cobre's 'La Caridad copper ore concentrator. At M de C, advanced ,control strategies have been 'installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, 'increased from 76;000 tpd to 90,000 tpd. Plantwide integration is expected' to gain an additional 3% improvement in profitability.

Jan 1, 1996

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG

Ni-M (Metal=Cu, Fe, Co, Mn, Zn, Cr) aerogel catalysts were tested for CH4 oxy-CO2 reforming. It was found that the Ni-Co bimetallic aerogel catalyst had the highest activity and stability in methane oxy-CO2 reforming among all the Ni-M aerogel catalysts. It exhibited a steady activity of 79 % (in terms of CH4 conversion) at 750 oC, which is the highest activity under a similar reaction condition as compared with those published in literature. Characterizations for the reduced catalysts indicated the formation of Ni-Co alloy, while other transition metals separated from Ni during the reduction process. Therefore, the active species in the Ni-Co bimetallic catalyst showed a stronger interaction than those in other Ni-M catalysts, which might be one of the main reasons for the better catalytic performance of the catalyst.

Jan 1, 2016

By S. L. I. Chan, M. Z. Quadir, D. C. Austin, P. J. Hazell, A. Chen, A. A. H. Ameri, D. East, J. P. Escobedo, M. A. Bevan, A. D. Brown

The microstructure and mechanical response of additive manufactured Ti64 under compression and tension has been investigated. Quasi-static and dynamic experiments were conducted on electron beam powder bed Arcam A1 (EBM) and blown powder laser Optomec LENS MR-7 (LMD) additive manufactured specimens. Hot isostatic pressing (HIP) was conducted on both of the additive manufactured specimens and results were compared with as-received specimens. Digital image correlation (DIC) was utilized to observe the in situ development of deformation fields during tensile loading. Optical microscopy was conducted on pristine and deformed specimens to examine the microstructure of the specimens. HIP treatment reduced the porosity by *90% with a concomitant increase in hardness by 40%. The results from tensile experiments show that additive manufactured Ti64 display a higher values for the yield stress, hardness, and ultimate tensile strength than conventionally manufactured Ti64. Under quasi-static compression, it was observed that EBM specimens exhibit a higher yield strength and ultimate tensile strength than LMD specimens.

Mar 1, 2017

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill as an aid in predicting the effect of corrosion on minerals and how this effect relates to downstream processing. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5% of the total grinding media wear in the operations studied.

Jan 1, 1987

By I-Min Lu

An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces. The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.

Jan 1, 1996

By Zhijing Zhang, Ramana G. Reddy

"The viscosity of molten oxides is one of the important physical properties since viscosity has a decisive influence on fluid flow. The knowledge of the viscosity of molten oxides is essential for modeling and controlling of metallurgical process. In the present study, viscosities of high basic Na2O-B2O3 and Na2O-SiO2 binary melts and viscosities of Na2O-SiO2-B2O3 ternary melts were measured as a function of temperature and composition. Experiments were carried out using rotary viscometer and graphite components. Our experimental results were compared with those in literature. Based on the current experimental data, the previously developed viscosity model was modified. The characteristic features of viscosities of these melts have been discussed. The predicted viscosity results are in excellent agreement with the present experimental data in the temperature range with molten state samples. IntroductionThe viscosity of molten oxides is one of the important physical properties since this property has a decisive influence on fluid flow, and is one of key factors to be taken into consideration in process modeling. The manufacturing operations require the viscosity of molten oxides to be within certain ranges. Although, some viscosity measurements on borosilicate systems have been carried out [1-4], the viscosity data in literature are available only for a few temperatures and cover small composition ranges. The agreement between the results of these works is not satisfactory [I-4]. Even the viscosities of binary systems Na2O-B2O 3 and Na2O-SiO2 generally are well studied, the available viscosity data in literature are only found in the composition range of O to 0.333 mole fraction ofNa2O. The aim of the present study is to provide a base with accurate experimental data for reliable model extrapolation."

Jan 1, 1999

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012

By P. M. Swash

The paper describes the use of mineralogical methods in the exploration and evaluation of primary diamond occurrences. The most common methods that are used include the systematic search for kimberlitic indicator minerals, surface textural study of the indicator minerals, (garnet, spinel, ilmenite and chrome diopside) and alluvial macrodiamond studies so as to understand their provenance and guide exploration towards diamondiferous targets. The mineral chemistry of the indicator is used to positively assess the origin of the mineral grains and is also pivotal in the determination of the diamond potential of a deposit. Petrography of the primary deposit is able to identify the body to be kimberlitic and is also a support to the mineral chemistry findings. Unambiguous proof of a prospects potential to contain macrodiamond is proven by the occurrence of microdiamonds in the residues from the rock. The presence of a sufficient number of microdiamonds in the rock is enough to determine a semiquantitative grade estimate and warrant further metallurgical evaluation so as to determine its actual macrodiamond content.

Jan 1, 1991

By U .. C. Rojas, J .. C. Gomez

"Fire Refined Copper (EI Teniente Three Stars) has been produced at Caletones Smelter of Codelco Chile since almost the beginning of its operations.Due to changing features of the copper market, together with the targets on technical efficiency and productivity, it has become more and more relevant for copper industry to reach both, good final product quality and a proper environmental control.At present, copper refining process at Caletones Smelter takes place in two cylindrical tilting furnaces, where solid fluxes are injected through horizontal tuyeres into the molten bath. (Fig. N2 1)Solid reagents are pneumatically conveyed and injected into the liquid copper bath attaining excellent solid - liquid contact, so the impurities removal efficiencies are found to be high. Same injection tuyeres are used to introduce both oxidising agent (normal air) and reducing agent (reformed gas) into the molten bath. Air or nitrogen is used as conveying gas for solid reagents, depending on the process stage.This pap~r gives a fundamental description of the process and industrial results related to the injection of blend of sodium and calcium carbonates to remove arsenic and antimony, silica and granulated reverberatory slag to remove lead and a mixture of calcium carbonate and mineral coal to reduce the selenium content of the fire refined copper."

Jan 1, 1996