Search Documents

By B. Beatty

Discussion by B. Beatty This is a response to M.J. Hrebar's paper, which tracks in detail the highly productive stripping capabilities of modern large bulldozers at two separate installations. It proves the old adage "economies of scale" and quantifies the advantage of being able to move large loads of dirt over comparatively short haul distances by sliding rather than carrying the load. This discussion examines whether a bulldozer is the most efficient way of using this geotechnical principle. Case 1 - Study eastern US: Contour coal stripping application The energy consumption for the Case 1 mining method (eastern US contour stripping operation) shows the D11 averaged 117 L (31 gal) of diesel fuel per scheduled hour, and produced 333.3 bank m3 (436 bank cu yd) per scheduled hour (0.351 L/m3). Assuming 1 L (0.26 gal) of diesel fuel contains 10.4 kW-hr of energy, the unit expenditure of fuel energy for Case 1 Study was 3.66 kWh/m3. Another way of shifting this material is by using an overburden slusher (OS), as shown in Fig. 1. The OS as shown in Fig. I. The OS is electrically powered and consists of a manned low wall winch (LW ), a remote controlled (radio telemetry) highwall winch (HW) and a hoe. The winches operate to pull the hoe back and forth across the pit. The hoe carries load in the forward direction ahead of a rear mounted blade and returns empty. A spreadsheet (Lotus 123) simulation package, BOSSIM, models the OS operation on a load by load basis over a wide range of pit configurations. The geometry shown in Fig. 2 of the paper was modeled using BOSSI M and the results are summarized in Table1. Table 1 shows a LW with 150 kW (200 hp) and a HW of 120 kW (160 hp) installed power, towing a 15-m3 (19-cu yd) hoe, would accomplish the Case 1 stripping task at about the same scheduled stripping rate (D11=333 m3/hr or 433 cu yd/ hour, OS=342 m3/hr or 447 cu yd/ hour). It was assumed the winches in this equipment have an electromechanical efficiency of 90%. This gives an average electrical energy expenditure rate of 151 kW-hr, and a unit energy expenditure level of 0.44 kWhr/m-3(0.57 cu yd/kWh)-an improvement of 8291%- over the D11 alternative. The energy comparison illustrates the importance of using more efficient electric power if possible, ahead of the internal combustion engine, and delivering power from a fixed ground position rather than through a moving track system. Another important energy observation is the comparative action of the dozer blade and the OS hoe. The former implement continuously digs and spills as it works the load forward. The OS hoe digs the load until full, the blade then lifts due to the contained load pressure and a shear plane forms under the mass, enabling it to slide forward in a force reduced - transporting mode. Economic comparison Table 2 operating cost per scheduled hour and unit cost comparison follows a format used in Tables 2 and 3 of Hrebar's paper and compares Case 1 Study with the OS alternative. Drill and blast costs are kept constant in both cases, although when larger OS units are considered, it is expected these costs will reduce because bigger hoe sizes will permit larger rocks to be transported efficiently.

Jan 1, 1995

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By Ing. E. h. Martin Herrenknecht, Werner Burger

In recent years, there has been a dramatic increase in the number of machine driven soft ground tunnelling projects. This increase is largely due to the technological development of slurry and EPB Shield systems. A new generation of soft ground tunnelling machines, markedly different from those of five years ago, now overcomes ground conditions that until now were too costly and impractical to undertake. The paper reviews the latest soft ground tunnelling machine developments in material transport, guidance and control, seismic surveying, soil conditioning, settlement control, cutting tool applications and variable mode operating systems. Specific projects where this technology has been applied will be highlighted.

Jan 1, 1999

By Yang Zhao, Wanping Wang, Siqing Liu, Shuming Wen

"In China, most reserves of rich iron ores have now been depleted and sustainable development of low-grade iron ores has become a critical discussion topic in the mining industry today. The aim of this study was to evaluate the applicability of beneficiating a low-grade, hematite-magnetite ore (assaying 18.64% Fe) for subsequent utilization. In this study, process mineralogy and beneficiation of the ore were carried out in the laboratory. First, mineralogical investigation shows that the main metal minerals are hematite, magnetite and a little octahedrite that cannot be used at present, and the main gangue minerals include albite, quartz and ankerite. Based on the above, a combined process of magnetic separation and gravity concentration has been developed by using laboratory low- and high- intensity magnetic separators and a slimes shaking table, respectively. Factors affecting these separation methods are discussed, including process mineralogy on the tailings of the high-intensity separator, where the iron minerals were found to be finely disseminated in the gangue as inclusions. By applying a two-stage grinding step and a magnetic separation stage together with gravity concentration, a marketable iron concentrate assaying 60.79% Fe at a recovery of 60.23% can be obtained, when the feed assays 18.75%Fe, which provides some useful information for the sustainable use of low-grade iron ore.IntroductionIron is the world’s most commonly used metal. Steel, of which iron ore is the key ingredient, represents almost 95% of all metal used per year, primarily in structural engineering applications and for maritime purposes, automobiles and general industrial applications. By the end of 2009, the iron and steel production in China ranked the first in the world, and reached 0.567 and 0.537 billion tons, respectively. The domestic supply of iron ore was 0.88 billion tons and about 0.628 billion tons of iron ore were imported in 2009."

Jan 1, 2015

By L. Cui

A new flotation collector, benzyl arsonic acid, was used for the flotation of ilmenite. ESCA, Auger spectroscopy, and chemical analysis were used to investigate the correlation between the variation in surface constituents and the flotation recovery of ilmenite. Experiments indicated that, as the ratio of surface Ti ions/surface Fe ions increases, flotation recovery increases. pH regulation with an inorganic acid was found to be effective in changing the ratio of surface ions, and, hence, the flotation recovery.

Jan 1, 1986

By Ross Goodman, Jesse Salai

The Ohio River Tunnel Project encountered multiple unexpected geotechnical challenges such as crown and invert instability due to the overstress condition affecting the strata above, below, and in the tunnel alignment during and after TBM excavation along with the potential for methane inflow. This paper showcases how the orientation of a tunnel alignment has a significant impact on how in-situ geological stress can impact the excavation of a tunnel from the contractor’s point of view and how geological features influence gas inflow to the alignment over time.

Jun 13, 2021

By Jim Huerta

Diesel fuel usage in the mining industry continues to escalate. This is because approximately 60 percent of all mined materials are surface extracted by large equipment using diesel fuel, which continues to increase in cost per gallon. For example, coal mining uses large equipment such as wheel loaders, wheel dozers, draglines and [ ] dredgers. In one year, three of the largest U.S. coal mining operations consumed approximately 567 million to 852 million L (150 million to 225 million gal) of diesel. At an approximate cost average of $3.25/gal the expenditure on diesel is $487 million to $731 million per year. So, are there any solutions that could reduce this cost burden? Yes, there are. Coal mining companies can extract less ore; use more efficient extracting equipment that consumes less fuel; wait for a significant reduction in the cost of fuel; or find and use technology that would create efficiencies that would lower the cost. Nanotechnology is one such technology that might provide the means to create the efficiencies that will significantly lower diesel fuel costs.

Jan 1, 2011

By Darrell V. B. . McClarty

In 1996, Rio Algom, Denison Mines and the Elliot Lake Research Field Station (ELRFS) formed a consortium to implement a regional environmental information management system (REIMS) for the Elliot Lake area in Ontario, Canada. ELRFS is an affiliate of Laurentian University in Sudbury, Ontario, The discovery of uranium in the Elliot Lake region in post-World War II led to the development of 12 mines and 11 associated mills between 1955 and 1958. During the late 1980s, declining world demand for uranium, combined with the discovery of high-grade uranium ore in other areas of the world, made the Elliot Lake mines uneconomical. As a result, all area mines ceased opera¬tions by the end of 1996. The eight facilities and three tailings management areas operated by Denison Mines and Rio Algom's five mining waste management areas contain 150 Mt (165 million st) of potentially acid-generating tailings. The areas cover 13.2 km2 (3,265 acres) and receive drainage from an additional 13 km2 (3,212 acres). The primary objective of the joint initiative was to implement a personal-computer-based, regional, environmental-information management system for managing historical data and ongoing environmental programs in the Elliot Lake region. The Elliot Lake consortium decided it needed an information system with an integrated, process-oriented and requirements-driven approach to collect and manage the environmental information. Following a study of environmental information management systems currently used by the mining industry, the consortium decided to base REIMS on the "Envista" product. This is a commercially available, environmental information management system marketed by Envista Technologies of Saskatoon, Canada.

Jan 1, 1999

By J. Iannicelli

Spray drying is the principal drying method used in the production of over six million tons annually of beneficiated kaolin in Georgia. Thirty-three dryers in the Georgia Kaolin belt comprise the highest concentration of large tonnage spray dryers in the world. The steady growth of spray drying in the U.S. kaolin industry is paced by advances in design and development of large spray dryers which have led to large scale new applications in mining and related industries.

Jan 1, 1982

By M. D. Martin

Low metal prices and increasingly stringent environmental regulations, coupled with the threat of higher governmental royalties are adversely affecting both existing and new operations. Existing operations must therefore be run at maximum operating efficiencies to enable mining companies to survive and grow. Well planned and executed "outsider" reviews can help achieve this goal. Many mine managers and those who direct them resist the idea of "outsider" reviews for a variety of reasons, some valid and some not. Those managers who do bring in the "outsiders" are nearly unanimous in reporting that the exercise in self-discipline was well worth the pain and effort and repaid the cost many times over. This paper makes a strong case for "outsider" reviews and gives recommendations on the kinds of reviews to undertake. The authors draw upon their nearly 70 years combined experience, much of which has been in operations.

Jan 1, 1994

By T. D. Parris

At the Frood Mine of International Nickel, tests were begun in March 1966 to evaluate the use of low profile diesel Load- Haul-Dump equipment in cut-and-fill operations. In December 1966, this test was extended to drawpoint loading of caved ore at the Creighton Mine. The results of these tests conclusively demonstrated the effectiveness of this equipment in the operations at International Nickel. This paper describes the equipment used, the operation of the equipment, production data and operating details. Also discussed in the paper are other trackless equipment which works with the Load-Haul-Dump carrier. Production and Safety comparisons are made with the slusher method in bulk mining, giving the reasons for replacing the slushers at the mines of International Nickel Company of Canada, Limited, Ontario Division.

Jan 1, 1969

By F. S. Knoll

Electrostatic separation is one of the most misunderstood physical processes used to beneficiate minerals. Nonetheless, millions of tons of titanium ores, iron ores and other minerals are processed every year economically, efficiently and safely. Over the past ten years major advances in electrostatic separation and its application have occurred. New processes include dewatering clay slurries, separating halite and sylvite, and shape separation of vermiculite and gangue minerals. Electrostatic separation techniques are based on one of two methods, electrophoresis or dieleccrophoresis -- processes involving charged and uncharged particles respectively. In some cases, the combination of these two techniques has proven quite useful. The purpose of this paper is to provide a basic understanding of the physical processes collectively called "electro- static separation" in order to enhance one's ability to define and consider new possibilities in mineral processing and other fields.

Jan 1, 1984

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomalous elements in a sample may be compared with similar sums for other samples, so that the samples having the greatest anomaly-ratio totals can be recognized easily. In partial or full-suites-of-ore-elements the use of anomaly ratios is more meaningful than analyzed values because the ratios quickly indicate anomalous elements and call attention to samples and localities that should be investigated.

Jan 1, 1980

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982

By D. Scott Scovira, Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1 ms increments up to 1500 ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits.

Feb 1, 2024

By Yingbao Yang, Jinyue Liu, Yonggang Wei, Bo Li

Due to the depletion of copper ore with high-grade and low impurity contents, the raw materials for copper smelting exhibit low copper contents and high impurities. High-impurity elements lead to the poor performance of the final copper product; thus, the removal of impurity elements during the oxygen-enriched copper smelting process is crucial. In this study, based on the production of high-grade matte, the occurrence states of impurity elements (such as As, Pb, and Zn) are analyzed in the input and output materials of the oxygen-enriched smelting process, and the phase transformation mechanisms of impurity elements are revealed during the oxygen-enriched smelting process. The effects of temperature, Fe/SiO2 ratio and oxygen concentration on the distribution behaviors of impurity elements in dust, slag and matte and the removal rates of impurity elements in matte are clarified. The results show that the impurity elements mainly exist as As4, As4S4, As2O3, Pb, PbS, PbO, Zn and ZnS in dust, as FeAsO4, As2O3, FeAsS, PbSiO3, Zn2SiO4 and ZnFe2O4 in slag, and as As, FeAsS, PbS, PbO and ZnS in matte. High smelting temperature, low Fe/SiO2 ratio and low oxygen concentration are beneficial for improving the matte grade and the removal rates of impurity elements Pb and Zn in matte. Low smelting temperature, low Fe/SiO2 ratio and high oxygen concentration are beneficial for removing impurity element As in matte.

Aug 8, 2023

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020

By Ken E. Baylis

Current over-capacity in coal production provides assured and relatively low-cost supplies to coal importers. At the same time, it is of serious concern to coal producers who invested considerable sums in the expectation that overseas demand would continue to grow rapidly. This paper assesses the reserves available for export, the export facilities, the coal supplies which can be put through them, and the market prospects for the future. It assumes, rightly or wrongly, that there will be no major and prolonged disruptions in supply from any major sources of coal. COAL RESERVES FOR EXPORT Economically recoverable reserves in the non-communist world amount to about 470 billion tonnes. These are sufficient to sustain current production levels of 2 billion tonnes a year for 235 years.

Jan 1, 1984

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.