Search Documents

By Robert B. Tippin

A number of recent studies 1-4 suggest that steelmaking expansion might be achieved more economically by a combination of the prereduction furnace and the electric steelmaking furnace rather than through new blast furnace construction. Supergrade concentrates would be the first step in an evolving technology which bypasses the blast furnace and in which the concentrates are first made into pre¬reduced pellets and then used directly in electric steelmaking, Prereduced pellets made from superconcentrates should not only be competitive with scrap, but should be a preferred feed for the electric furnace because of the absence of such residual elements as copper and nickel. Furthermore, geographic areas remote from present steelmaking centers may find the electric furnace to be an economical method of providing local steel requirements. The development of successful methods of producing superconcentrates may also be expected to find application to conventional blast furnace burdens. The need for methods of increasing grade of domestic concentrates will become increasingly urgent in the face of competition from high grade imports. Only a small percentage of domestic iron ore production can qualify as superconcentrates, (Superconcentrates for the purpose of this investigation are limi¬ted to those concentrates which contain a maximum of 2 percent S'02). During the last several years the Twin Cities Metallurgy Research Center of the Bureau of Mines has directed research efforts to develop methods of manufacturing superconcentrates from present standard grade products by cationic flotation, screening, and magnetic separation.

Jan 1, 1971

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By W. H. Stahl

The continuous vacuum filtration is the solid-liquid separation process that is nowadays most frequently used in the beneficiation industry all over the world. After a development time of several decades, the various filter types such as drum filter, disk filter, plate filter and belt filter can be consideres as a sound functional design ensuring a trouble-free operation. Nevertheless, the vacuum filtration does no longer meet the present and future technological requirements. The moisture content of filter cakes is too high. Their thermal secondary drying is too expensive (coal, ores) and may bring about undesirable material changes and the filter cake conditioning with water-binding substances for dumping purposes is too costly.

Jan 1, 1983

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Lixue Wen, Jun Xiao, Dongping Shi, Yan Xue, Jinmiao Wang

Mine ventilation energy consumption is one of the main sources of energy consumption in mining production, accounting for about one-third to one-half of the total energy consumption. Therefore, reducing the energy consumption of the mine ventilation system is crucial for mining production. With the premise of meeting the airflow requirements of the underground work areas and achieving sustainable development of mining production, this paper establishes a nonlinear optimization mathematical model for the mine ventilation network with the objective of minimizing the total power. Regarding the model, optimization of the decision variables was carried out using the method of minimum spanning tree. The constraints for air flow balance, wind pressure balance, and fan operating conditions were optimized using the exterior penalty function method, thereby transforming the model into a nonlinear unconstrained model. Based on this model, a modified sooty tern optimization algorithm (mSTOA) was proposed to achieve optimization. Improved the sooty tern optimization algorithm (STOA) by using the uniform reverse strategy, fitness value-distance balance selection strategy, and mutation strategy. The STOA, mSTOA, and three other classical optimization algorithms were applied to the optimization of a ventilation system of an actual mine. The experimental results show that after using mSTOA to optimize the ventilation network airflow distribution in the mine, the total energy consumption can be reduced by about 35.06% while meeting the constraints and demands of the ventilation network regulation and usage. This is of great value to mine roadway operation environment safety and clean production.

Dec 20, 2023

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By Xiaodong Yu, Jinxia Zhang, Fusheng Niu, Hongmei Zhang

The three-dimensional (3D) fractal dimension is an important parameter to analyze the 3D structure and flocculation effect of the hematite flocs. In this work, the 3D fractal dimension of hematite flocs was predicted by establishing the particle swarm optimization (PSO) algorithm optimized with the back propagation (BP) neural network (PSO-BP). The proposed model considers four factors, namely, the flocculant quantity, flocculation time, stirring speed, and temperature, as the input parameters. We normalize the input data during the preprocessing stage. The BP neural network was optimized by using the PSO algorithm for realizing the 3D fractal dimension. The prediction accuracy and effectiveness of the model were evaluated. The experimental results showed that the predictions performed by the proposed PSO-BP neural network were better than that of BP neural network. In addition, the root mean square error (RMSE), mean squared relative error (MSRE), mean absolute error (MAE), and mean absolute relative error (MARE) of the proposed model are lower, compared with the errors of the BP network. Similarly, the measurement coefficient R2 of the proposed model is higher, compared with the BP network. The maximum absolute error of the model is 0.0772, the maximum relative error is 0.02405, and the regression coefficient r is 0.98592. These results showed that the proposed model has a good performance and high prediction accuracy. When verifying the practicability and the effectiveness of the proposed PSO-BP model, the prediction results of 10 groups of hematite flocculation experimental data under different conditions showed that the prediction value of the proposed PSO-BP model was closer to the ground truth as compared to the BP model. Therefore, the proposed model is suitable for predicting the 3D fractal dimension of hematite flocculation.

Oct 3, 2022

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By Lei Zhang, Zhibo Ma, Pingye Guo

The mechanical behavior of hard roofs often leads to significant deformation and strong mine seismicity in gob-side entry retaining (GER) of the longwall mining, affecting the mining safety and efficiency of coal mines. Field investigations indicate that the failure process of the retained entry by hard roofs can be divided into three stages. In this paper, theoretical analysis and numerical simulations are first used to evaluate the damage process of the retained entry under the hard roof. The results show that the instability of the retained entry in the conventional GER method results from the combined static-dynamic loads (in stage II and stage III) from the hard roof. Then, an innovative method, through fracturing roofs to maintain entry (FRME), based on GER with the hard roof is introduced to solve this problem. In this method, the roof of the mining area is pre-fractured, and when the coal seam is mined, the direct hard roof will collapse along the fractured surface due to its deadweight and mining pressure. The hard roof control effect on the static and dynamic loads, taking into account the innovative method, is verified with simulations and theoretical analyses. The results are compared with those of the conventional GER method. Furthermore, based on the numerical simulation study of dynamic responses, it is found that compared to the GER method, the dynamic response of the retained entry using the innovative method is more moderate and more conducive to the stability of the entry. Field application also validated the effectiveness of the innovative method to control the mechanical behavior of the “massive sudden collapse” of the hard roof.

Aug 14, 2023

By A. J. Richins, M. G. Nelson, R. Dunne

From the inception of flotation in the late 1800s, coarse particle recovery has been a challenge to practitioners. By the early 1900s, flotation processes included oil flotation, skin flotation, agglomeration flotation, and froth flotation, and for each there was a proliferation of flotation equipment. Ensuring good coarse particle recovery included desliming of the feed and proper conditioning were required. Froth flotation was at first used mainly to treat finer materials from grinding circuits. The maximum size for coarse particles was from 3.18 to 4.78 mm. In froth flotation, large particles with high specific gravity tend not to be recovered. Coal and minerals of low specific gravity and flaky minerals such as graphite, mica, and talc can be floated in larger sizes. In the early 1960s, the phosphate industry began using column cells to recover coarse particle by froth flotation, but early columns suffered from poor bubble generation and sanding at the flat base of the column. Recently, improved coarse particle recovery has been the object of new cell designs—the Eriez HydroFloat™, the Jord NovaCell™, the FLS coarseAir™ cell, and the Cidra P29 integrated system. The paper will follow the development of coarse particle flotation with a focus on the development, laboratory assessment, and operation of the new flotation equipment and technology designed to recover coarse particles.

Feb 22, 2026

By H. Lawrence

In 1977, the Bureau of Mines awarded a grant to the State of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the State. Work had been done in Aiken County prior to the grant by Bureau of Mines and State personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1-100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two U.S. Geological Survey (USGS) 7 ½ min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than ±91.4m (5300 feet). Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). Figure 1 shows a portion of one quadrangle overlay. Table I gives a comparison of acreage measured for sever- al mines from the 1-100 and IDIMS systems vs. aerial photo measurements.

Jan 1, 1979

By Tyler Lahti, Peter Borgacci, Mary Jane Ferraro, Prakash Nadesparan

Toronto Tunnel Partners (TTP), under contract to Metrolinx/IO, is constructing new twin rail tunnels under the Highway 401 & 409 interchange to accommodate additional tracks to support the GO Expansion program for future two-way, all-day service. The new tunnels are being constructed using the Sequential Excavation Method (SEM) and utilize a tunnel pre-support system consisting of a series of 800 mm diameter steel pipes to form a pipe canopy. The pre-support pipes were installed with an Auger Boring Machine (ABM) in four separate headings; one heading from each of the tunnel end portals, and two from a shaft in the middle of the highway. To facilitate the auger boring operation, a custom steel reaction frame was required to counteract the thrust from the ABM at the portals, and a temporary shaft structure was installed in a narrow median space of the highway. The installation of the pipe canopy had to overcome challenges including removal of obstructions, alignment issues, and controlling settlements to the highway surface. This paper discusses the purpose of the pipe canopy, design and installation of the temporary shaft and structures to support the auger boring operation, the experience of the contractor during the installation of the pipes, and brief overview of the experience tunneling below the pipes.

Jun 13, 2021

Peru has become an established mining country. The industry and industry-related businesses account for a significant amount of the country´s revenue, on state and local levels. But like other countries with thriving mining industries, Peru has seen its mining industry revenues fall off in recent years due to a lackluster global economy. And the mining industry in Peru must also deal with increasing concerns about mining?s environmental impacts, local community and other social issues, as well as a regulatory environment that has placed more restrictions on what miners can do. That said, the Peruvian government is beginning to realize how important mining and natural resource development is to building the nation?s economy, improving its infrastructure and lifting its population out of poverty. The government support was evident during the Perumin 2013 mining convention, held in September in Arequipa. In addition to Peru?s President Ollanta Humala speaking at the closing ceremony, the country?s ministers of Energy and Mines, and Economy and Finance participated in the event, as well as numerous other federal and state authorities. Perumin is put on by the Instituto de Ingenieros de Minas del Peru (IIMP, or Peruvian Institute of Mine Engineers). The 31st edition of the convention, billed as the ?world?s largest mining convention? by the IIMP, this event was led by Abraham Chahuan CEO of Antamina and Romulo Mucho (SME member) as president of IIMP, attracted about 118,000 participants from more than 48 countries. This was more than the anticipated 75,000 attendance and well past the 51,000 people who attended the 2011 convention. The last edition of PERUMIN was led by the CEO of Compañía Minera Antamina, Abraham Chahuan and Rómulo Mucho (SME member) and representative of the IIMP. The event attracted more than 1,000 journalists from all over the world, the IIMP said. A total of 2,213 booths from equipment and machinery supplying companies from the five continents were present at the Mining Technology Exhibition (Extemin), including companies from the United States, Canada, China, South Africa, Germany, Australia, Brazil and Chile, among others. The convention has grown so large in recent years, that the IIMP shifted its location from Tecsup vocational school in Arequipa to the Cerro Juli Convention Center. The venue is 116 percent larger than Tecsup, the IIMP reported, covering about 20 ha (40 acres). It was reported by Latinomineria magazine that about 10 million Peruvian soles were invested in the new venue to create a world-class events center. It was also estimated that the event generated more than 234 million soles to Arequipa?s economy.

Feb 1, 2014

By T. Bednarski, T. McCallum, L. Moya, B. Gay

"Molybdenum recovery by solvent extraction has gained interest partly due to advances in concentrate leach technology. Historically, both molybdenum and rhenium have been produced using amine-based extractants with the ability to co-extract both metals. Alternatively, a phosphinic acid-based extractant (CYANEX® 600) can be used depending on the flow sheet. CYANEX® 600 selectively extracts Mo leaving Re in the raffinate, which is a valuable feature in plants which require rejection of the rhenium from the molybdenum circuit. CYANEX® 600 piloting results are reviewed and compared to commercial experiences with an amine-based extractant. INTRODUCTION Molybdenum is most commonly found as molybdenite (MoS2) in primary porphyry deposits (about 59% of global reserves) and copper porphyries (about 39% of molybdenum reserves)[1]. Recovery from molybdenite traditionally involves flotation (concentrates typically containing 85 – 95% MoS2) followed by roasting to produce MoO3. Solvent extraction is also used to recover molybdenum from acidic aqueous solutions resulting from scrubbing of roaster and smelter off gasses and leaching of molybdenite (uranium ores). Molybdenum is also frequently found in low concentrations in copper leach inventories[2]. More recently, pressure oxidation has gained interest to treat molybdenite concentrates. Molybdenum Chemistry The chemistry of molybdenum is complex with a series of extractable species existing dependent on the pH and oxidation state as shown in Figure 1.Under strongly basic conditions, molybdenum primarily exists as MoO42- while under strongly acidic conditions MoO22+ becomes the predominant species. In between, a number of isopolymolybdates such as Mo7O246- and Mo8O264- are dominant. Equations (1) – (3) demonstrate some of the proposed molybdenum equilibrium reactions[1]."

Jan 1, 2017

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023

By A. L. Mular

A great deal of effort is being expended by mineral processing engineers to acquire a basic knowledge of modelling and optimization techniques. Stimuli such as immediate process improvement, expanded process understanding, optimal flowsheet design and re-design, and the development of new and better control systems are goals which excite the imagination in terms of increased profits. To reach these goals, process models and efficient optimization strategies, regardless of their purpose, assume an important role. Consequently, few of us can argue that such efforts are of no value. The purpose of this paper is to review empirical modelling methods and optimization strategies which appear to be of value to mineral engineers.

Jan 1, 1972

By Changshou Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,175 t (3,500 st) of ore per day with an average gold grade of 12.6 g/t (0.4 opst). The mine has a large horizontal extent of 762 by 152 m (2,500 by 500 ft) and a vertical extent of 6 to 61 m (20 to 200 ft). Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for mining design and operation in the Leeville underground mine. Three methods are used to collect the geotechnical data in the Leeville underground mine: • Core logging. Most geotechnical data are collected by this method, which is based on exploratory drills and estimates parameters for rock quality designation (RQD), fracture frequency (FF), compressive strength and rock mass rate (RMR). • Site investigation. This method collects more detailed geotechnical data and geostructural data from work done in the underground drifts and stopes. Parameters of RQD, FF, compressive strength, RMR, rock tunneling quality index (Q) and geostructural data are estimated. • Data collected from drill holes made for the critical infrastructure facilities. This method provides the best detailed geotechnical information for areas in which the critical infrastructure located. A complete geotechnical database has been constructed using this geotechnical data collection system. The database can be used for the design of ground support, stopes and stope blasts, among other critical applications.

Jan 1, 2010

By Ashis Bhattacherjee, Rahul Upadhyay, Nearkasen Chau, Aditya Kumar Patra, Dhanjee Kumar Chaudhary

Heavy earth-moving machineries used in openpit mines intensively expose drill operators to whole-body vibration and shocks, and thus to musculoskeletal disorders. The roles of individual, machine and rock-related factors in their exposure remain poorly understood. This cross-sectional study investigated their roles in 39 drill operators from Indian iron ore mines. It shows that 70 percent of the operators were exposed to high levels of vibration, above the limit values recommended by ISO 2631-1 (1997). Multiple linear regression models showed that the whole-body vibration and shock exposures were strongly associated with operator’s age, drill-machine model and rock hardness, uniaxial compressive strength and density. The role of body mass index was close to significance (p = 0.08). Univariate analyses found the drill’s age, seat-pad thickness and seat backrest height were also strong predictors. These results help in identifying risky operators, materials and occupational situations, and in implementing appropriate prevention and intervention strategies to reduce and monitor the exposures and health risk. In addition, during the planning stage of acquisition of new equipment, anthropometric data of the operators should be considered for the ergonomic design of the seat.

By C. N. Savage

An industrial minerals review involves an attempt to assemble field and statistical data which are obscure, elusive and incomplete. Often, when me statistical data are available, combining or lumping of commodity values conceals the value of specific items. Personal knowledge of the minerals known to occur in the area of concern, combined with whatever available published data may be compiled, together with careful use of several extrapolation methods, may yield an acceptable summary review of the industry. However, it is particularly hazardous to speculate on future trends and economic aspects because of the many unpredictable variables which may affect the industrial minerals business. Among these variables are the effects of diverse geological conditions, the impact of technological changes (including new uses for minerals not formerly considered industrial types), changing socio-economic factors (including growing environmental controversy), use of substitutes and even recycling of some of the industrial minerals (for example, building materials, lime, etc.). My main objectives are to reveal, as accurately as I can, the state of the in¬dustrial minerals situation, and the effects of possible future developments on this industry in Idaho. Where the words...industrial-tyke minerals, .are used in this discussion, reference is made to selected metallic and nonmetallic minerals and related materials, as well as rock (Table I). Industrial minerals known to be present in Idaho may be listed under general use categories as in Table 1. Some of these commodities are being marketed, have been marketed in the past, or occur in potentially marketable quantities. Mineral fuels are neither mentioned, nor are they considered important in Idaho. Based upon our present knowledge and lack of known, economically valuable occurrences of these commodities, they are considered insignificant (Idaho Bur. Mines and Geology, 1964). Information used for this study is from several sources. Most of the statisti¬cal information should be credited to the U.S. Bureau of Mines Minerals Yearbooks,

Jan 1, 1971

By T. J. Loyd

The capabilities of the analog computer, the Mine Ventilation Simulator, installed at WHA's Safety and Health Technology Center in Denver, Colorado, are discussed. General opera- ting procedures are described showing how a mine model is produced, and how the model can subsequently be modified to produce a solution to a mine ventilation problem. A sample problem is included to illustrate the technique. The important role the Mine Ventilation Simulator plays in ventilation training is discussed, including experiences with the education of students at the Colorado School of Mines. This paper includes a summary of some of the advantages and disadvantages of the analog technique and suggests some design criteria for application to future development of analog computers, based on experience gained with the Mine Ventilation Simulator.

Jan 1, 1984