Search Documents

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By David E. Siskind

The Bureau of Mines has studied the problem of cracking in residential structure walls from vibrations produced by blasting in surface mines. Direct observations were made of blasting damage consisting primarily of cosmetic cracking in plaster and gypsum board walls. Measurements of structure response and also application of the response spectra analysis single-degree-of-freedom model were used to quantify the frequency dependence of the safe level criteria. An overall summary analysis was performed using the new Bureau of Mines damage observations and data obtained from nine previous studies, including the three analyzed earlier by the BuMines for Bulletin 656, published in 1971. Separate analysis of the high- and low-frequency damage cases, structural response, and two types of construction resulted in the establishment of safe vibration levels ranging from 12 mm/sec to 50 mm/sec (0.5 in/sec to 2.0 in/sec).

Jan 1, 1980

By R. L. Virta

Twenty-three companies mined kaolin in nine States in 2004. Production was estimated to be 7.6 Mt (8.3 million st) valued at $912 million, based on preliminary data. This was a slight decrease from 7.68 Mt (8.46 million st) valued at $939 million in 2003.Georgia was the leading producer state with an estimated 6.5 Mt (7.1 million st) in production. It was followed, in decreasing order of tonnage, by South Carolina, Alabama, California, Texas, Arkansas, Nevada, Florida and North Carolina. Georgia accounted for nearly the entire domestic water-washed, delaminated, and pigment-grade calcined kaolin production. Consumption Sales to the paper industry accounted for 49 percent of domestic sales and 64 percent of total sales. Other major markets for domestic sales were refractory products (10 percent), paint (5 percent), fiberglass (4 percent), catalysts (3 percent) and rubber (2 percent).Paper coating and filler markets accounted for about 87percent of export sales of kaolin.

Jan 1, 2005

By J. J. Fallon

The subject is "Mergers, Acquisitions and Divestitures in Industrial Minerals, but my remarks could also be applied to new product development, resource development and other new business development activities. At the kernel of the subject is due diligence in major decision-making, that is, where major money amounts and a large corporate commitment are at stake. The "due diligence" means how carefully we do our homework before making the decision. The homework or feasibility study addresses different parts of the decision. In the industrial minerals business the study seeks to uncover the pros and cons in: o The mineral reserves, quantity, quality, mineability, access, etc. o The environmental impact of mining, processing and transporting. o The economics of operations. o Financial aspects o Legal aspects o Many other aspects o And -oh yes! the marketing aspects.

Jan 1, 1990

By Trevor Ellis

The following is extracted from a report by the author to the International Valuation Standards Committee (IVSC), with minor modifications for the purpose of publication. The author represented the IVSC at the annual session of the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology. This is a body organized by the United Nations Economic Commission for Europe (UNECE). This second session, held in Geneva, Switzerland, achieved an important agreement for advancement toward uniform global standards for the classification of minerals and petroleum reserves and resources. Attendees discussed the possibility of enhancing the United Nations Framework Classification for Energy and Mineral Resources (UNFC) for implementation globally as the classification standard for use in financial reports under the International Financial Reporting Standards (IFRS). Presently, there are between 100 and 200 mineral and petroleum resource classification (or definition) systems throughout the world — a similar number to what there are countries.

Jan 1, 2006

By Ben Sosewitz

The subject of rapid excavation tunneling is one that is extremely important to the people in the Metropolitan area of Chicago. My personal observation is that it is also extremely important to the urban communities around the U.S., to many local and state governments, and to the public officials who are deeply concerned about state affairs and taxes. The Metropolitan Chicago area is in fact, (as are 40 other major urban areas in the U.S.) confronted at the present time with a very serious combined sewer overflow, drainage and pollution problem which accounts for an estimated 40% of the pollutional load on its waterway system. In response to this the District has to date spent some seven millions of dollars in an attempt to find the most economical solution available for the elimination of this problem. This study included extensive investigations of the geological strata, the quantity and quality of storm runoff to be dealt with, and the various methods of storage and treatment available. It has considered solving the overflow problem by a concept involving a series of tunnels, rock tunnels, shafts and storage areas which will collect, retain and subsequently treat that portion of the combined sewer overflow which can be handled in the most cost-effective and economical way, consistent with following the federal and state standards - with which we at the present time agree in principle.

Jan 1, 1997

By Furuyama Takashi, Mori Sukeyuki, Hara Tsuyoshi, Fukushima Yujin

In mineral processing practice, flocculation is largely established as an engineering technique of waste water treatment and the study of parameters increasing the settling velocity of particles is still of great importance to improve the process. Further investigations were made using quartz (Q89) and fluorite samples (F91) which included 58.8% and 65.8% of -2.3 µm particles respectively. In all the experiments the flocculation phenomena were observed varying the pH value of the aqueous suspension. In contrast to quartz particles (Q89) which did not flocculate for all pH values, it was, noticed that fluorite particles (F91) flocculated in the alkaline range of pH over 11. With an aqueous suspension containing equal quantities of Q89 and F91, a hetero-flocculation of particles was observed at a range of pH below 10. In this case, the maximum floc size of the hetero-flocculation was 37.0-26.2 µm This size was about three times larger than when quartz (Q84) and fluorite particles (F85) were used with 32.4% and 40.4% of -2.31 µm particles respectively. Besides, in the experiments using Q89 and F91, the maximum size of hetero-flocculated single particles was found to be 6.54 µm instead of 3.27 µm as obtained with Q84 and F85.

Jan 1, 1995

By Carrie Smith

The Society for Mining, Metallurgy & Exploration’s annual conference and expo, MINEXCHANGE 2026, will take place Feb. 22–25, 2026, at the Salt Palace Convention Center in Salt Lake City, UT. The event will foster a hub for innovation, technical exchange and policy discussion for the global mining industry. Over four days, attendees will take part in short courses, technical sessions, field trips and networking events that highlight the advancement of the mining industry. The conference’s keynote session, titled “Regaining America’s Mineral Dominance,” will start at 8:30 a.m. on Feb. 23 in the Grand Ballroom E–J. The speaker will address the sweeping policy actions now shaping the nation’s mineral future, following a series of executive orders issued by the Trump administration designed to bolster domestic mineral production and energy security. These directives, including Immediate Measures to Increase Domestic Mineral Production (EO 14241) and Establishing the National Energy Dominance Council (EO 14213), have set in motion a coordinated effort across the Departments of Interior, Energy, Defense and Commerce to enhance the United States’ position as a global leader in critical minerals. The invited speakers include Utah Governor Spencer J. Cox and Nate Foster, managing director of Rio Tinto Kennecott, who will examine how policy and industry are converging to meet surging demand for minerals essential to modern technology. Governor Cox is expected to highlight Utah’s long-standing role in American mining, from the early development of Kennecott Copper to its current position as a producer of 40 of the nation’s 50 identified critical minerals. Foster, meanwhile, will offer insights into Rio Tinto’s extensive operations in Utah, including the Kennecott Copper Mine — one of only two operating copper smelters in the United States — and the company’s ongoing efforts to build more resilient, sustainable supply chains. Rio Tinto’s work in critical mineral production, from copper and tellurium in Utah to new operations in Arizona, has made it a fundamental figure in the U.S. mineral economy. Projects such as the Resolution Copper development and the revival of Gunnison Copper using Rio Tinto’s innovative Nuton technology illustrate how private-sector leadership is driving sustainability in domestic mining. These advancements come at a critical moment for the industry, as copper prices remain near historic highs. The keynote session will emphasize that meeting future mineral demand will require a concerted effort between government, industry and technology partners to secure responsible, domestic production. Immediately following the keynote, the Robert E. Murray Innovation Award Lecture will start at 10 a.m. as part of the same session. Lucy England, managing director at FLSmidth, will present on “Sustainable Copper Mining Flowsheets and the MissionZero Mine.” England, who has spent more than 25 years in mineral processing and innovation, will discuss how FLSmidth’s MissionZero initiative aims to develop the world’s most efficient

Feb 1, 2026

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

By K. Pathak

Loaders and dump trucks are the most commonly used surface-mining equipment. Negligence of the safety-engineering aspects of dump trucks may result in serious accidents in a mine. A reduction in the risk of an accident due to the deployment of trucks can he achieved by engineering analysis, risks assessment, improved safety features, active safety devices, condition-based maintenance, in-built protection systems, etc. This paper presents some cases of accidents in Indian surface coal mines and advocates a systems approach to safety.

Jan 1, 1999

Most statistical and geostatistical methods of re-source and reserve estimation work extremely well for Normal (Gaussian) well-behaved information. However, most interesting mineral deposits exhibit far from this idealistic distribution of values. It seems that the more valuable the mineral, the less likely the data are to have a Normal distribution. Values tend to be "positively skewed" with a long tail into the high values. Using averaging techniques, such as inverse distance or ordinary kriging may result in consider-able overestimation of grades and tonnages unless such values are cut or otherwise modified. This paper presents some real case studies where distributions are (a) highly skewed and (b) the product of multiple phases of mineralisation. Practical methods are presented for solving such problems including combinations of indicator and log normal kriging methods. The emphasis of the presentation is on developing operational methods which can be used on project evaluation or grade control in producing mines.

Jan 1, 2000

By W. Jacobi

INTRODUCTION The radon problem concerns the radiation exposure from inhaled short-lived radon daughters and the associated risk for the induction or promotion of lung cancer. In several groups of miners which were exposed in the past to relative high radon levels during their underground work, an excess lung cancer frequency has been observed. On the basis of these findings it has to be stated that the inhalation of radon daughters is the most important radiation hazard in mining. Involved in this radon problem in mines are the difficulties to measure the individual radon daughter exposure of miners and to estimate the dose to critical cells and target tissues in the lung from inhaled radon daughters. And finally the reduction of radon levels in mines confronts us with special technical problems which are difficult to solve. Thus the setting of annual limits for the radon daughter exposure of miners alone is not sufficient to guarantee an appropriate standard of radiation safety. Of same importance are the improvement of air monitoring and the optimization of technical protection measures in mines. This has to be kept in mind for the following considerations on exposure limits. The ICRP has recommended in 1959 for the first time a maximum permissible concentration (MPC) for the occupational exposure to radon and its short-lived daughters (ICRP, 1959). This MPC in air was derived from a maximum permissible dose equivalent of 0.15 Sv (15 rem) per year to the epithelium of the large bronchi which was regarded as the "critical tissue". This old MPC-value was derived using a simplified lung model which paid main attention to the dose contribution from the inhalation of unattached 218Po(RaA) atoms. Since this time more realistic dosimetric models for radon daughters have been developed; some of these models will be presented in special papers on this conference. Furthermore in the last 10 - 20 years substantial epidemiological information on the lung cancer risk among several groups of Rn-exposed miners has become available. Taking into account these epidemiological and new dosimetric findings the ICRP has adopted in March this year new recommendations on occupational limits for inhalation of 222Rn, 22ORn and theirshort-lived daughters. This report will be published this year as ICRP Publication 32 (ICRP 1981). The recommended limits for radon daughters were derived from the basic dose and risk limits as they were proposed by ICRP in its new basic recommendations (ICRP Publ. 26, 1977). In the following this basic system of dose limitation is shortly outlined before the special recommendations for radon daughters are described. [BASIC CONCEPTS AND LIMITS] The new basic recommendation of ICRP (Publ. 26, 1977) proceed from the assumption that in the dose range which is relevant for radiation protection, the risk RT of so-called stochastic radiation effects (carcinogenic and genetic effects) in a target tissue T increases proportionally with the mean dose equivalent HT in this tissue: RT = aT HT. If several target tissues are irradiated the total individual (stochastic) risk is given by the sum of risks in these tissues: [R = ?TRT = ? T aT HT]. Thus this concept of individual health detriment takes into account the risk contribution from each relevant tissue. It replaces the old concept of the critical tissue, which neglected the exposure of other tissues. Applying this new concept a dose quantity can be defined which is proportional to the total individual radiation risk from stochastic effects. This so-called "effective dose equivalent (HE)" is given by the sum of the weighted dose equivalents in the relevant tissues: [HE = E wT HT with E wT = 1 T '1] The weighting factor wT of each tissues follows to wT = aT/awB, where awB is the total stochastic risk coefficient for a uniform irradiation of the whole body. For the lung as a single organ comprising several target tissues, the ICRP recommends a total weighting factor w = 0.12 (ICRP 1977/79). This concept of risk or detriment, respectively, has important consequences. To meet the objectives of radiation protection the new ICRP-system of dose limitation is based on the following three principles: 1) The justification of practices involving radiation exposures; no pratice shall be adopted unless it produces a net benefit. 2) The ALARA-principle that all exposures shall be kept as low as reasonably achievable; this requires the optimization of the level of protection. 3) The limitation of individual exposure (annual dose limits). It is important to note that the dose limits for individuals are only one part of this system of dose limitation. Furthermore, these limits cannot be regarded as a boundary between safe and unsafe. They have to be interpreted as the lower boundary of an unacceptable exposure region. This means that in addition to the observance of these basic dose limits it is demanded to optimize the level of protection. Consequently the optimized exposure levels or the corresponding operational limits will be normally lower than

Jan 1, 1981

The Mining Foundation of the Southwest will host its 24th Annual American Mining Hall of Fame Awards Banquet at the Tucson El Conquistador Golf & Tennis Resort in Tucson, AZ on Saturday, Dec. 9. The Mining Foundation of the Southwest is a non-profit organization whose objectives are public education about the mineral industries. It also recognizes outstanding accomplishments in and contributions to the fields of fuel and mineral resources.

Jan 1, 2006

By Robert M. Matyas, P. E. Sperry, Robert J. Smith, A. A. Mathews

INTRODUCTION The first Dispute Review Board (DRB) was utilized on a tunnel project 20 years ago. Increasingly utilized on a wide range of construction projects, DRB's are becoming the norm on tunnel and underground projects. This paper summarizes the growth in this usage, uses observations and experience to establish that barriers to the utilization of DRB's are more perceived than real and that many arguments against the DRB concept are not valid, and notes some of the salient elements that should be considered in practice to optimize DRB effectiveness. The purpose of the paper is to provide an annotated checklist for current and prospective users. The basic concept, structure, and operation of DRB's are described elsewhere and will not be repeated here (ASCE, 1991). DISPUTE REVIEW BOARD USAGE A compilation of Dispute Review Board usage for tunnel and underground projects to January 1994 indicated use on 63 contracts with a cumulative construction value of $3.8 billion and a total of 60 disputes settled. As of that same date, DRB's were planned for another 63 contracts with an estimated construction value of $4.7 billion. (A listing of these 126 projects is available from the authors.) This success and popularity have spread to other civil projects as well as process and building construction. The increase in DRB usage has been exponential. See Figure 1.

Jan 1, 1995

By U. Thorley

Management of mine and tailings reclamation activities by surface mining oil sands operations in Alberta, Canada is experiencing increased national and international attention. Of particular concern is the ability of existing mines to execute and fund reclamation activities. Concern stems from a lack of demonstrated tailings reclamation technologies, perceptions of a poor track-record of reclamation activity by industry, and a lack of transparency with respect to the potential cost of reclamation activities relative to the monies secured in Alberta?s Environmental Protection Security Fund (EPSF). Limited information is publicly available regarding reclamation costs and technologies. Available data typically comes from disparate sources. This paper examines the expected costs of oil sands reclamation activities through a study of corporate Asset Retirement Obligation (ARO) liabilities, the Province of Alberta?sEPSF, and published data relating to reclamation costs.Issues relating to current liability funding are introduced.

Jan 1, 2011

By Y. Wang

China is a big mining country with a long mining tradition and history. At present, there are nearly 200,000 different mines and 21 million workers. The total production value of mining makes up 6% of GNP. With the development of economy, the mining industry has played a more important role in our economic market, supplying more than 95% non-reusable energy, 85% of industrial and agricultural raw materials, over 75% of fertilizers and 30% industrial and agricultural water.

Jan 1, 2001

By Andrew Finney

INTRODUCTION The Sacramento Regional County Sanitation District (SRCSD) serves unincorporated areas of Sacramento County, parts of the cities of Sacramento and Folsom, and the cities of Citrus Heights, West Sacramento, Rancho Cordova, and Elk Grove. SRCSD maintains 145 kilometers (km) (90 miles) of interceptors that convey a combined total of 0.6 million meters3 per day (160 million gallons per day) or more of waste-water, with additional miles of sewer interceptors that are scheduled to be built by 2020. Wastewater is conveyed to the Sacramento Regional Wastewater Treatment Plant in the southwestern portion of the County, also managed and operated by SRCSD, in interceptors with diameters as large as 3.0 m (120 inches.) As part of its overall expansion program, SRCSD has constructed a number of major interceptors over the last few years with tunneling methods due to concerns associated with either the impacts of open cut construction in an urban environment (traffic, safety, noise, environmental concerns) or the need to achieve a crossing of a stream, river, or transportation corridor. This paper focuses on a specific issue that affected construction of the Upper Northwest Interceptor (UNWI) Sections 3&4 project, located at the northern limit of the SRCSD service boundary and within the limits of the City of Sacramento. This project involved the construction of 3.2 km (2 miles) of 2.1-meter (84-inch) and 2.4 km (1.5 miles) of 1.7-meter (66-inch) diameter reinforced concrete pipe (RCP) using MTBM, EPBM, and 3.3-meter (130-inch) two-pass TBM methods. The owner elected to install the RCP using tunneling for a number of reasons including a desire to avoid traffic impacts in a dense urban corridor, to minimize disturbance to the neighborhood, and to avoid potential dewatering-induced settlement issues along the western one-third of the project. For the western portion of the alignment the 2.1-meter (84-inch) reinforced concrete interceptor pipe was to be installed using a 2.7-meter (105-inch) earth pressure balance machine (EPBM). No external dewatering of shafts or tunnels was permitted for reasons of concern about settlement, discussed previously. At the intersection of Elkhorn Boulevard and Natomas Boulevard (at the extreme northwest corner of the project) the 2.7-meter (105-inch) EPBM tunneled past a recently constructed 11-million liter (3-million gallon) water storage reservoir, passing within 3 meters (10 feet) of the tank?s shallow foundation while tunneling through clean sands with a shallow groundwater table. The paper will discuss the implemented solution to mitigate additional settlement risk that was developed as a joint collaboration between the owner, CM, designer, and contractor.

By T. Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With. Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. In 1990, Cyprus Amax began aggressively searching for such an opportunity. Early in 1997, production will commence at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1,750-tonne per day open-pit operation that will produce more than 300,000 ounces of gold per year. This paper discusses the challenges of locating such a prospect, doing business in Russia, developing supply lines, identifying work force capabilities, gaining government approvals, securing financing, arranging for gold sales and ultimately building a facility in this arctic region.

Jan 1, 1997

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1990

By R. K. Rajamani, A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999