Search Documents

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By T. G. Legare

It is now well documented that trace amounts of silver, gold, and platinum group metals occur in certain geothermal brine deposits. A significant body of literature has been generated over the last twenty years which describes attempts to quantify the frequency and levels of these precious metals in the brines. This literature is often confusing and contradictory. For example Barnea 1 states that the Salton Sea geothermal field carries 2 ppm gold, yet more recent data by workers at Lawrence Livermore National Laboratory2 (LLNL) concludes that the gold level in Salton Sea brine is <0.07 ppb. They report a platinum level in one well of 55 ppb. This apparent contradiction may be explained by sampling source and technique, but is most probably explained by difference in analytical technique. Analytical techniques and problems will be discussed in the next section.

Jan 1, 1985

By R. L. Russell

Production at Freeport Indonesia&apos;s Ertsberg open pit copper/gold mine started in 1972 at a rate of 7500 t/d. Mill throughput remained at that rate for a number of years until the discovery of the Ertsberg East (GBT) orebody. This discovery prompted three successive expansion stages from 1981 to 1988 that boosted production to 20,000 t/d. The discovery of the huge Grasberg porphyry copper deposit in 1988 launched a new era of much larger expansions. The first of these involved installation of a fourth primary mill in 1989 to bring production up to 32,000 t/d and was immediately followed by an expansion of the crushing and screening plant and the addition of a new south concentrator to bring production to 57,000 t/d in 1991. The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 has served to optimize current production at a level of 66,000 t/d. A major expansion is now in progress. This includes construction of another new concentrator to house a SAG mill circuit and large Wemco flotation cells in an area created by the removal of 6,000,000t of glacial material. This current expansion, with a planned completion in 1995, will take production to 115,000 t/d. This paper describes the evolution of the Freeport Indonesia (FI) concentrator to-date and will then go into an in-depth discussion of the 66,000 and 115,000 t/d expansions.

Jan 1, 1994

By Christa Overby

As part of the City of Portland, Oregon?s East Side Combined Sewer Overflow Tunnel Project, nine separate 2,130 mm (84-inch) diameter reinforced concrete pipe microtunnel drives totaling approximately 2,380 m (7,808 ft) are being constructed to divert flows from several of the existing outfalls to the main tunnel. The drives were constructed in challenging ground conditions that include soft soils under the ground-water table, large amounts of wood and metal debris, and close proximity to sensitive structures. While all of the drives will be addressed, the focus of the paper will be on the 931 m (3,055 ft) continuous drive connecting Outfall 46, currently the longest microtunnel driven in North America.

By William S. Hallager

Banded ironstone and associated fine-grained carbonaceous sediments near Jardine, Montana, are enriched in gold, arsenic, and tungsten. The mineralized sediments lie within a thick sequence of quartz-mica schists cut by a 2.6 b.y, granite. Surface, underground, and drill hole mapping are used to construct structure contour maps of individual ironstone lenses. Each lens is then unfolded by triangulation of minimum surface path distances between drill hole penetration points. Major and minor element abundances in composite ironstone samples are interrelated through R-mode factor analysis. Results indicate five significant element groupings thought to reflect coarse detrital, fine detrital, sulfide-rich chemical, iron-rich chemical, and epiclastic ultramafic sediment. Ultramafic factor scores are highest in a previously undefined rock type rich in cummingtonite, biotite, and chlorite; lacking in quartz; and closely associated with at least one ore horizon. Detrital dilution of ironstone, calculated from chromium and nickel content, drops off significantly as ore-bearing ironstone is approached. This observation may indicate that centers of gold precipitation have protected themselves, either topographically or by rapid deposition, from detrital contamination. Gold mineralization correlates most strongly with the sulfide- rich factor. Gold may have been introduced through hotspring activity as a bisulfide complex.

Jan 1, 2013

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man&apos;s house as it was mined. Then it may have been stockpiled at each man&apos;s place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

By H. H. Murray

Clay minerals are one of the more important industrial minerals. They are used in many products and because of different specifications may require special processing which can be either wet or dry. The clays discussed are bentonites, kaolins including ball clays, and palygorskite (attapulgite). In order to design a process flow sheet for these clay minerals, the physical, chemical, mineralogical, and optical properties need to be evaluated. Each species of clay minerals require a group of special tests which are described in this paper.

Jan 1, 2009

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By Amin Mousavi, Soroush Khazaei, Yashar Pourrhimian

As a factory-like method, sublevel caving consists of development activities, stockpiling and production activities that are carried out on different levels independently. Therefore, considering the operation from the development phase to the plant will lead to more reliable production scheduling. This paper presents a mixed integer linear programming framework for the long-term production scheduling of sublevel caving that maximizes the net present value while satisfying development activities, mining, and processing capacities, continuous mining, the allowable number of active mining units, grade blending, and vertical and horizontal sequencing. The model is coded in Jupyter Notebook and is solved using the CPLEX solver.

Jun 25, 2023

PolyMet Mining is developing the NorthMet property near Duluth, MN. Laboratory investigations have led to the development of the Platsol process to dissolve in one step the base metals (copper and nickel) as well as the gold and platinum group metals (PGM). To complete the prefeasibility study, a fully integrated, 10-day pilot plant trial was undertaken. The trial consisted of high-temperature (>220ºC or >428ºF) pressure oxidation in the presence of 5 to 10 g/L chloride (the Platsol process). This was followed by solid/liquid separation, gold plus PGM recovery from solution, conventional copper solvent extractions/electrowinning (SX/EW) and recycling of the copper raffinate to the autoclave. The concentrate tested during the trial period was a NorthMet bulk flotation concentrate. It assayed 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t (0.041 oz/st) Au, 2.2 g/t (0.064 oz/st) Pt and 9.9 g/t (0.289 oz/st) Pd Laboratory results were confirmed and, with minor adjustments of the laboratory Platsol conditions, the following leach extractions were obtained during the pilot plant trial: 99.6% Cu, 98.9% Ni, 96% Co, 94.6% Pd, 96 % Pt and 89.4 % Au.

Jan 1, 2003

By Jason Morrison

The Norwegian Lake Tap Method was successfully used to tap into the side of Lake Dorothy 36.5 m (120&apos;) below the lake surface. The lake tap allows water to flowinto an access tunnel from the lake lowering the water elevation below its natural out-fall. When the lake reaches a predetermined elevation below the outfall, a 1.5 m (60?) valve in the tunnel will be shut and discharge from Lake Dorothy will stop temporarily allowing construction of a dam located 2.9 km (1.8 miles) downstream at Bart Lake. The lake tap and tunnel were one phase of the $64 million Lake Dorothy Hydroelectric Project, owned and operated by Alaska Electric Light & Power Company (AEL&P), a private utility located in Juneau, AK. The Lake Dorothy portal site and tunnel are located approximately 25.7 km (16 miles) southeast of Juneau, AK, in the remote Tongass National Forest at an elevation of 701 m (2,300&apos;) above sea level in the mountains above the Taku Inlet. Thirty degree snow covered mountainsides and limited access by helicopter were just two of the many factors which challenged this unique project. The lake tap and tunnel development consisted of 250 m (820&apos;) of horizontal tun-nel, averaging 3.6 m x 3.6 m (12&apos; × 12&apos;), excavated using conventional drill and blast methods in highly competent Granodiorite and Tonalite rock, placement of one 3.9 m (13&apos;) long concrete plug, or bulkhead, located at the tunnel midpoint, and one 3 m (10&apos;) diameter lake tap into the side of Lake Dorothy. This paper will provide an analysis of the logistical and engineering challenges involved in the development of one of only a handful of lake taps in North America. AEL&P and contractor J. S. Redpath Corporation worked together to complete this critical project phase safely and on schedule, in a location accessible only by helicopter and plagued by constantly changing, harsh weather conditions. A strict schedule had to be maintained to ensure the timely operation of the downstream dam and power plant.

By William Gleason

"It is safe to say that the coal industry, in the United States and globally, is currently suffering through one of the hardest times in its history.A perfect storm of competition, changing energy demands, politics and public perceptions have collided, inflicting significant harm to the industry that many say is irreparable. This, in turn, has led to massive job losses in some regions, heavy cuts in production and even bankruptcy filings from two of the largest coal mining companies in the nation.Cheaper natural gas can certainly take a large share of the blame for the struggle of coal, as utility companies switch from coal to natural gas for power generation. According to the U.S. Energy Information Administration (EIA) the amount of coal used for electricity generation in the United States is at a 45-year low.November 2015 marked the fifth consecutive month that natural gas was the leading source of power generation in the United States. EIA said generators produced 101,866 thousand megawatt hours (MWh) of electricity with gas in November versus just 87,789 thousand MWh with coal, the lowest monthly level since May 1980 when monthly coal use was 84,884 thousand MWh.According to Robert Godby, director of the Center for Energy Economics and Public Policy at the University of Wyoming, there are a number of factors playing a role in the decline of coal, but he points to the advances in fracking as the tipping point.“A lot of people will argue that regulation is the cause of the decline, and it has played a part, for sure, but the story of the recent past is more about what competition has done to the energy market,” Godby told Mining Engineering. “The war on coal was originally declared by natural gas in 2008.”The price of natural gas, which was at $13 per million Btu before the gas fracking boom, has fallen to as low as $1.68 in December 2015. Likewise, Godby said the cost of wind generation is now lower than the cost of generation from coal and the cost of solar generation is coming down as well. In addition to that, the demand for energy has changed in the past five years with more efficiencies in everything from building design to lightbulbs."

Jan 1, 2015

By R. P. Proulx

The Meikle Mine is a high grade, underground goldmine utilizing primary-secondary longhole open stoping with delayed backfill to produce 2700 tpd(3000 stpd) of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 166°C (330°F) were measured. In the early stages of mining, the mine experienced premature detonations using different explosive products. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

Over 800 mines have closed in Australia in the past 25 years. This paper summarizes the data obtained from those closures and includes all Australian States and Territories and all commodities, including metalliferous, coal and industrial minerals. Twenty five percent of the mines closed due to resource exhaustion or depletion; 24% due to high costs, price drops, or declining grades; 8% due to open pit resource depletion (but with underground reserves remaining) or underground reserves depleted (but plans to open cut remainder) and 7% due to receivership or voluntary administration. The environmental, social and economic impacts of these closures are also significant and include acid mine drainage and impact on mine employees. An understanding of the causes of premature mine closure will better equip mining companies and governments to better manage future mine closures, wherever in the world the mines are operating.

Jan 1, 2007

By J. Pinkley

DSI DYWI Rock Dust application is aiding in enhancing safety and productivity in underground coal mining. DSI DYWI Rock Dust combines wet dusting technology and polymers to allow for drying and lift characteristics for rock dusting. DSI DYWI Rock Dust typically dries within 24 to 48 hours depending upon the mine air velocity and humidity. The DSI DYWI Rock Dust Applicator Machine is a completely hydraulic unit. The DSI DYWI Rock Dust Applicator machine allows for batching of product and face spraying operations in permissible locations. The DSI DYWI Rock Dusting Applicator Machine fits in one half of a battery or diesel scoop bucket for ease of transport. It is completely hydraulically powered by the PTO circuit. The DSI DYWI Rock Dust Applicator unit requires a scoop operator, and a person to operate the spray wand, simple operation with two personnel. The first demonstration was at an underground continuous miner room and pillar coal mine which produced a pilot test period opportunity, which proved to be successful, and has now been in full launch mode with the US underground coal mining industry. A typical batch of operation allows for 250? of roof and rib (19? wide by 6? in height) coverage of DSI DYWI Rock Dust application. The DSI DYWI Rock Dust Applicator contains a hydraulic powered air compressor which allows for 30-50% more coverage per batch by improved dispersion of product via air assist spray nozzle. DSI DYWI Rock Dust will add approximately $0.02 to $0.04 per clean ton of coal cost to the mining operation over traditional rock dust cost depending upon mining height.

Jan 1, 2012

Six pioneers of the American mining industry will be inducted into the National Mining Hall of Fame on Saturday, Sept. 13, at the Museum Convention Center in Leadville, CO. The 16th annual Mining Hall of Fame induction banquet will begin with a reception and open house at 5:30p.m., followed by the dinner and program at 7 p.m. The six inductees include James M. Gerstley, the only living member, and George O. Argall, Jr.; John F. “Leadville Johnny” Campion; Charles R. Nailler; Edwin N. Pennebaker and Russell L. Wood.

Jan 1, 2003

By M. J. Shulman

An algorithm used by the US Coast Guard to find lost objects is utilized to optimally allocate exploration efforts during initial stages of an exploration program. Based on classical search theory, the algorithm assumes a target probability distribution function, a detection func¬tion, and a cost function. The three Junctions are analogous to delineating areas of possible mineralization, choice of exploration methods, and exploration budget. Application of the algorithm is shown for a hypothetical target distribution. Using the maximum number of field days available as the cost function, the optimal allocation of effort is shown for different exploration methods, e.g. electromagnetic survey and induced polarization. The adaption of the algorithm for the exploration process is discussed.

Jan 3, 1984

By Richard F. Coon

Six potential locations along the west shore of Lake Mead were evaluated to site anew water intake pumping station for the SNWA. The evaluations were based upon geotechnical exploration results and conceptual intake pumping station designs. The exploration included geologic mapping, geophysical testing, underwater ROV inspections and borings. Ground surface and underground chamber pumping station designs were considered. Sites at Saddle Island, Black Canyon and Hoover Dam are geotechnically suitable. A Saddle Island site was selected because it has the most favorable conditions for the intake pumping station and the aqueduct to the Las Vegas valley.

Jan 1, 1997

By E. Hughes, D. Akers, D. Stopek

The Upgraded Coal Interest Group (UCIG), focuses on clean, low-cost options for coal-based power generation via pre-combustion, co-firing and reburn options. Its mission is to preserve and expand the economic use of coal for energy. By reducing the fuel costs and environmental impacts of coal-fired power generation, existing units become more cost effective and thus new units utilizing advanced combustion technologies are more likely to be coal-fired. Two great forces are reshaping the power generation industry, the Clean Air Act Amendment and deregulation of generation. The Clean Air Act Amendment is forcing change by making it necessary for power producers to plan for reducing emissions of sulfur and nitrogen oxides and possibly trace elements. At the same time, deregulation of generation is forcing utilities to focus their attention closely on the short term impact of any change on cost of power. Fuel is a utility&apos;s largest cost element; maximum fuel flexibility will be a utility&apos;s best weapon in an environment of rapid change. In a regulated environment, a utility was limited in how involved he might get into fuel supply, in a purely deregulated environment he need only be guided by the impact on the bottom line. It is clear that these two forces will promote a close look at factors such as coal upgrading which can have an impact on the availability of low sulfur coal or emission of NOX and trace elements.

Jan 1, 2000

By C. Asgaard

Asset availability has been a longstanding objective in mining and mineral processing plants around the world. Enormous resources in both dollars and manpower are invested in improvement efforts to achieve higher asset availability. One dimension of asset availability is the time equipment is out of service for large scale planned maintenance activity: grinding mills, kilns, furnaces, mobile equipment, shovels and draglines are all regularly taken out of service for extended repairs and service. The speed, cost and quality of these planned outages provide an opportunity to increase asset availability. Equipment shutdowns are projects that are executed in a compressed time period. This paper will describe how the overall time and cost of equipment shutdowns were significantly reduced at Cliffs Natural Resources Michigan Operations (CNRMO) through the introduction of the Critical Chain Project Management techniques.

Jan 1, 2009