Search Documents

By D. A. Lucero, J. E. Brockmann, L. A. Mondy, K. L. Rubow, D. J. Rader

"Department of Mechanical Engineering, University of Minnesota, Minneapolis, MNExperimental and correlated stage responses (the fraction of particles entering an impactor that are collected on a stage) are presented for the Andersen Mark III and Marple personal cascade impactors. The impactors were operated upright and fully assembled so that interstage interference and wall losses could be properly studied. The observed stage responses showed maxima that fell significantly short of unity, meaning that a monodisperse aerosol is never collected exclusuvely on one stage, but is distributed among several stages and internal losses. Correlations for the stage responses are presented so that the experimental results can be used to determine size distributions with available data-inversion algorithms. Simulations with log-normal distributions show significant differences between dpa50 histograms and the more accurate distributions that result by taking the response functions into account.Cascade impactors are widely used for the measurement of aerosol size distributions; their ruggedness and simplicity of operation make them an attractive choice for a variety of environments. In one common application, the aerosol of interest is drawn through the impactor, and the amount deposited on each stage is determined gravimetrically. The primary objective is to extract as much information as possible about the initial size distribution from the resulting set of weights. Unfortunately, the reconstruction of contin-uous size distributions from finite data sets is an ill-posed problem. Not surprisingly, a variety of such reconstruction techniques are presently in use; the success of each method depends on the particular nature of the aerosol sample and the instrument response.Inversion of impactor data by any of these techniques requires that the response functions for each stage be known. The stage response function gives the fraction of particles entering the impactor that deposits on that stage. Values of the response function range from zero to one, and depend on impactor operating conditions (e.g., geometry, flow rate, and gas properties) and particle properties (e.g., diameter, density, and shape factor). As interstage interferences and particle losses will affect each stage's response, experimental determination of stage responses should be made for fully assembled impactors. Unfortunately, impactor stage response functions are rarely reported; rather, single-stage efficiency curves are given that provide an incomplete description of impactor performance.This paper presents experimental stage responses for two fully assembled cascade impactors: the Andersen Mark III and Marple personal impactors (model 298, Andersen Samplers, Inc., Atlanta, Ga.). These calibrations were performed with monodisperse liquid droplets for both impactors and also with monodisperse solid spheres for the Marple personal impactor. The calibration results for the Mark 111 impactor presented here have been previously reported in the response-function format (Rader et al., 1989). The calibration results for the Marple personal impactor, however, were originally presented in the single-stage efficiency for¬mat (Rubow et al., 1987) and have been reanalyzed in this work. Losses within both impactors are considered, and their treat¬ment within data inversion techniques is dis¬cussed. In addition, correlations for each impactor's response functions are presented so that these calibration results can be easily included in data-inversion algorithms. Size distribution inversions using these response correlations are compared with the standard cut-point method for two lognormal test dis¬tributions."

Mar 1, 1992

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased about 4% in 1990. The decrease in the value of tripoli production was the result of a decrease in total production. Emery decreased owing to a decrease in the volume of the material produced. Special silica stone experienced a decrease in unit value and in the quantity produced. Garnet showed an 8 % increase in quantity and an 8 % increase in unit value. Staurolite increased about 38 % in the quantity produced, and the value of production increased about 36 %. The fused aluminum oxide industry showed a 12 % decline in the quantity produced and a 13 % decline in the value of production. The silicon carbide industry saw a 47 % decrease in the quantity produced and a 23 % decrease in the value of production. Combined, the industries decreased 17 % in quantity and value compared with those of 1990.

Jan 1, 1993

By John B. Gayle

The probable inadequacy of physical tests of coke for the purposes for which they are made has been a subject for discussion for many years. However, little has been published in this connection, even though most workers in the field believe that the physical properties of coke are of major importance in its utilization in the steel and allied industries. In fact, the reproducibility of the recognized tests is largely unknown or can only be approximated. This situation occasions many difficulties when attempts are made to judge the coke-production qualities of various coals or coal blends. During World War II the Coke Production Committee, composed of representatives from industry and the Solid Fuels Administration, concluded that study of existing testing methods and possible improvements would be of material assistance in answering questions relating to coke quality. Since that time the Bureau of Mines has taken samples of coke produced in industrial slot-type coke ovens in connection with studies aimed at extending coking-coal reserves by adding to the list of sources known to be suitable for this purpose. Testing procedures on these cokes were arranged so that the data obtained would yield information on (1) the degree of precision of tests commonly used in the industry, (2) the causes of the known poor reproducibility in several of the physical tests, and (3) possible improvements or modifications of existing physical testing procedures.

Jan 1, 1953

By L. A. Neumeier

The Bureau of Mines evaluated the properties of a Zn-0.75 pct Cu-0.12 pct Ti alloy extruded at temperatures between 400° and 720° F. The extrusions were made with a reduction ratio of 28-to-l and at relatively slow speed. Rod was also extruded at 560° and 640° F with a reduction of 255-to-l. With increased extrusion, temperature, extrusion pressures decreased substantially and creep resistance of the rod improved significantly. Coefficients of thermal expansion were low in the long rod dimension. Microstructures, hardness, and tensile properties were also evaluated, and a limited evaluation was made of bend ductility at 32° F for the rod extruded with the 255-to-1 reduction.

Jan 1, 1969

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961

By Jack G. Croeni

A study was made by the Bureau of Mines to determine the influence of high energy-rate deformation on the structures and properties of low-carbon steel, stainless steel, titanium, titanium-6 percent aluminum-4 percent vanadium, beryllium, molybdenum, and tungsten. The purpose of this study was to determine relative formability, the effect of energy and temperature on metalworking parameters and resulting structures, and the properties of materials formed by this technique. Forming techniques were limited to upset forging and direct extrusion on pneumatic-mechanical forming machines. Results show that considerable grain refinement can be achieved by careful control of deformation and forming temperature by high energy-rate techniques. Significant improvements in strength were observed as a result of this refined structure. Approximate deformation resistance as a function of temperature was determined for a variety of materials.

Jan 1, 1966

By R. R. Brown

The solubility and the activity of aluminum chloride hexahydrate, A1C13?6H2O, in aqueous solutions were determined as a part of the Bureau of Mines, U.S. Department of the Interior, research to improve mineral processing technology for recovering alumina from low-grade domestic resources. The solubility of A1C13 in pure water was found to be 31.09 and 31.77 wt-pct at 25° and 85° C, respectively, and decreased drastically to 10 and 0.1 wt-pct when the respective amounts of 20.3 and 37 wt-pct hydrochloric acid (HCI) were added in solution. The equilibrium constant for the solubility of hexahydrate, activities, and activity coefficients of A1C13 and H2O were calculated and compared with the results from the available methods of estimation. The results were shown to be useful in leaching nonbauxitic ores for extraction of alumina by changing the solubilities of component salts upon addition of HC1. Simultaneous solubilities of A1C13, FeC13, KC1, and NaC1 in solutions of HC1-H2O were also determined and their effects on the purity of A1C13?6H20 crystallized from mixed salt solutions are briefly discussed.

Jan 1, 1979

By S. A. N. Sheya

Many gold-bearing ores in the Western United States also contain small amounts of mercury. The presence of mercury creates potential pollution and health hazards during several steps in gold processing. An investigation was undertaken by the Bureau of Mines to develop techniques for removing mercury from cyanide mill solutions by selective electrowinning to reduce the potential hazards. Sixty-five percent of the mercury was selectively electrowon from synthetic carbon strip solution at applied potentials of 1.00 to 1.50 V when using a mercury-coated platinum or copper plate cathode. Increasing the active surface area by using mercury-coated copper wool resulted in up to % pct of the mercury being electrowon from mill carbon strip solutions that contained 1.9 to 20 ppm Hg, 20 to 345 ppm Au, and 0.35 to 39.5 ppm Ag. About 98 pct of the silver was electrowon with the mercury onto the mercury cathode. Gold extraction ranged between 0 and 20 pet. Results of the investigation showed that choice of cathode material was critical to the success of the process. Selectivity was not achieved using uncoated steel wool cathodes.

Jan 1, 1988

By P. D. Kovscek

The Bureau of Mines has tested a low-thrust water-jet-assisted rotary drill. This work was performed to evaluate the performance of a water-jet-assisted drill operated at thrust levels typical of a handheld manual-thrust operation. Prior work by the Bureau had indicated that using water-jet assist with high-thrust drilling applications would increase drilling rate. Small-diameter holes were drilled in five different types of rock. Thrust and water pressure were varied as the drill rate was monitored. The test results indicate that drilling rates increase with increasing water pressure and thrust. The water jet has more effect on reducing the specific energy when drilling in the harder rocks than in softer rocks. Variation in drill rate for a given rock sample is attributable primarily to the material heterogeneity within the sample. One rock type (Greenwich sandstone) could not be drilled efficiently with the water-jet-assisted drill.

Jan 1, 1988

To develop a business case that promotes adoption of noise controls by reducing barriers to industry acceptance and enhancing drivers that foster their implementation. Background Over 75% of the U.S. mining workforce is exposed to hazardous noise, putting them at risk of noise-induced hearing loss (NIHL). Consequently, coal miners suffer high rates of hearing impairment that increase to 70%-90% by retirement age. To address the noise problem for coal miners, researchers from the National Institute for Occupational Safety and Health (NIOSH) first determined that the continuous mining machine (CMM) ranked first among machines associated with reported coal noise overexposures. Further studies found that most CMM noise is generated by three component systems on the machine: dust collection, cutting, and conveying. Of these systems, the on-board chain conveyor was found to be a dominant noise source. Noise generated by the conveying system was addressed through the development of a urethane-coated flight bar chain. The coated chain, shown in Figure 1, has demonstrated an 8-hour time-weighted average (TWA) reduction of operator exposure by 3 dB(A). It has since been accepted by the Mine Safety and Health Administration (MSHA) as a "technologically achievable" noise control for CMM operators who are exposed to noise that exceeds the MSHA permissible exposure level. Having demonstrated the noise reduction performance of the coated chain, NIOSH has assembled information into a business case that can be used by operations considering adopting the chain at their worksite.

Dec 1, 2009

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990

By R. Van A. Mills

Crude oils are capable of dissolving quantities of gas under pressure. This fact has been known for some time, but questions have arisen as to the effects of gas in solution upon the characteristics of the oil. Previous investigations4 show that gas in solution in an oil affects the viscosity and surface tension of the oil, but the effect's on the volume and A. P. I. gravity of the oil have not been known. The results given in this report show that there is a decided change both in volume and in the A. P. I. gravity of the oil due to the solution of the gas in the oil under pressure. As gas is dissolved, the volume of the oil and the A. P. I. gravity increase. The converse of this phenomenon is also true: if the gas is released from a saturated oil, there is a shrinkage in volume and a decrease in A.P.I. gravity due to the release of gas from solution. However, various oils show marked tendencies to retain a portion of the dissolved gas upon releasing the pressure to that of the atmosphere. This retained gas has an appreciable effect on the volume and A. P. I. gravity of the oil because the oil does not resume its initial volume or gravity while it retains dissolved gas. In a sense the oil has been "Freshened" and will not return to its original or weathered volume until it loses some of the lighter fractions. Wiggins5 has shown that a fresh oil decreases both in volume and in gravity because of the weathering of the lighter fractions while the oil is standing in storage tanks.

Jan 1, 1928

By R. E. Meaker

Electrical conductivities and densities of molten fluoride systems were measured as functions of the melt temperature and composition. For any given mixture, the two properties change linearly with temperature. Three alkali metal fluorides were selected as solvents for melts of the type LiF-, NaF-, and KF-MFx, where M is a metal selected from the alkali metal or alkaline earth groups, or from the lanthanide or actinide series of elements, and x = 1-4. Heats of activation for conductance were calculated from the experimental data and varied from 2.3 to 9.2 kcal/mole at 1,000° C. Some relation between position in the phase diagram and the conductivity changes was suggested.

Jan 1, 1971

By A. A. Sonnek

A simple, portable helium analyzer was developed primarily for field use. Its utility lies in making preliminary surveys before exact analyses are required. The analyzer is based upon chromatographic principles; that is, separation of gas mixtures resulting from variable retention times of the components with respect to a separation medium (column-packing material). It uses thermistors for sensing detectors, a dry battery as source of power, and a micro-ammeter for indicating helium concentration. The absolute accuracy of the instrument depends upon the recency and care with which the instrument is calibrated with a standard gas. The unknown gas should be analyzed immediately after calibration, and another calibration should be made before another unknown sample is analyzed. The instrument is simple to operate, requiring approximately 15 minutes, after calibration, to determine the helium content of a natural gas sample. Although developed primarily for helium determination, the analyzer possibly can be used for other analyses that can be performed at ambient temperatures.

Jan 1, 1965

By Frank J. Wiebelt

In its efforts to maintain production of tungsten during the recent war period, the Bureau of Mines explored certain parts of the properties of the Atolia Mining Co. in San Bernardino County, Calif., by diamond drilling. Owing to past production record and other available data, the area was considered attractive for possible development of new ore bodies. Scheelite occurs in narrow veins ranging in width from a fraction of an inch to several feet. The veins are in quartz monzonite in a zone 2 miles long and 500 feet wide. Production from the district was reported to have been over 1,000,000 units of W03. Twelve diamond-drill holes, totaling 5,056 feet, were drilled by the Bureau of Mines in the vicinity of the Papoose, Papoose No. 5, Amity, and Union mines, the tailings pond, and the "Old Spud Patch." The work began in August 1943 and was completed in June 1944. This publication briefly describes the history and deposits of the district and gives full details of the work performed by the Bureau.

Jan 1, 1950

By John P. Walsted

Because of the absence of an iron-producing industry, the Pacific Northwest is working under an economic handicap. This is particularly apparent in the gray-iron-foundry industry because of the high price of pig iron imported from foreign sources or shipped in from producing ?areas within the United States. The high prices and sometimes short supply of ferrous metal products has put a brake on industrialization, which has been only partly compensated by the availability of cheap electric power. The economic condition of the gray-iron-foundry industry could be improved by establishing a small iron-producing industry based on the locally available ores. Moreover, establishing a local iron smelter would create a market for resources now dormant. Low-grade ores of manganese, chromium, and nickel would become usable in industry when combined with the iron ore from Scappoose. Pig iron produced in even limited quantities would level out the fluctuation in supply. The ore deposits, being small, would not supply enough pig iron to satisfy the entire demand. This condition necessitates designing special pig irons that will carry abnormally high proportions of scrap in the cupola charge.

Jan 1, 1955

By J. F. McIlwain

As part of its goal to minimize the requirements for critical materials, the Federal Bureau of Mines has investigated the consolidation of an iron-base superalloy (20 pct Cr, 5 pct each Ni and Mn, 1 pct each C, W, Mo, and Cb, and the balance Fe) and its modifications by powder metallurgy (P/M) techniques. Vacuum-atomized, prealloyed powder was used. Consolidation was by sintering of cold-pressed alloy powder, or by forging plus rolling or extrusion of canned powder. Several commercial lubricants were evaluated in the pressing operation. At 50-tsi compacting pressure with up to 3 wt-pct lubricant, green strengths did not exceed 1,000 psi. Powder sintered just below the solidus temperature attained a tensile strength of 69,000 psi and 4 pct elongation. Liquid-phase sintering produced higher densities, lower tensile strengths, and nil ductility. Canned powder was forged and rolled at 1,200° C, yielding a 100-hr rup¬ture strength of 9,800 psi at 815° C and a room-temperature tensile strength of >130,000 psi at 6 pct elongation. Heat treatment of modified P/M iron-base alloy containing 0.63 pct C resulted in a 100-hr rupture strength of 17,000 psi. Oxidation resistance at 805° to 815° C of the forged and rolled P/M iron-base alloy was similar to that of the cast iron-base alloy and supe¬rior to conventional stainless steels.

Jan 1, 1981

By Edward D. Thimons

The Bureau of Mines conducted a state-of-the-art study of techniques currently employed to close large openings in underground mines. A large opening was considered to be any opening over 10 feet high and having a cross section of at least 200 square feet. Five salt mines and one limestone mine were visited to observe various methods of sealing large openings. Because of the variations in conditions from mine to mine, no definite conclusions could be drawn as to which is the best method. In mines where waste material is available, stoppings built by piling waste material are efficient and economical. Where waste material is not available properly constructed brattice cloth stoppings are superior to those built from wood, concrete block, or urethane foams.

Jan 1, 1975

By John E. Pahlman

The Bureau of Mines conducted column-leaching tests on 25 domestic Mn ores to determine the feasibility of extracting Mn by in situ or heap leaching with dissolved sulfur dioxide (S02) solutions. The ores tested were obtained from deposits in Arizona, Arkansas, California, Colorado. Maine, Minnesota, Nevada, and South Dakota. Dissolved S02 was found to be effective for leaching Mn; extractions greater than 90 pct were obtained with solution application rates of 1 mL/min from uncalcined, minus 2.5-plus 1.3-cm ore pieces. Leaching these ores with solutions containing only 5-wt-pct S02 and no added H2S04 resulted in Mn being selectively extracted over Fe except when Fe was present as goethite or siderite. Ca solubilization was inhibited by controlling the solution application rate (1 mL/min). The rate of leaching was found to be principally dependent upon the rate at which the leaching solution can penetrate the ore, since the solubilization of Mn upon contact with S02 was observed to be rapid. Despite low water permeabilities of the ores (as low as 10-2 to 10-4 darcy). greater than 90 pct of the Mn was extracted from even the largest ore pieces tested (approximately 10 cm in diameter). It appears, therefore. that leaching Mn opens up the pores, allowing penetration of the leach solution into the ore pieces.

Jan 1, 1988

By Thomas M. Barczak

This U.S. Bureau of Mines report describes methods to enhance the capacity, stiffness, and timber utilization of wood crib supports. Since stiffer supports minimize strata deflections that contribute to roof instability, efforts to maximize crib stiffness while maintaining stability through a wide displacement range should be a design priority. The stiffness and capacity of conventional crib designs, employing alternating layers of wood timbers that are loaded perpendicular to the grain, can be increased by increasing the interlayer contact area or by using higher strength wood. Contact area can be increased by using wider timbers or employing more timbers per layer. Concepts that provide parallel-to-the-grain timber loading will provide substantial increases in crib stiffness and capacity. Two concepts that utilize this principle are examined: (1) an original South African design that constructs wood cribs from preformed layers (mats) of timber where short blocks are oriented vertically between horizontal slabs; and (2) a design that employs full lengths of timber placed vertically in the interior of a conventional crib structure. These designs also provide more efficient timber utilization by providing greater support capacity per volume of wood used in the crib construction.

Jan 1, 2010