Search Documents

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing gypsum mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation so that there may be no misunderstanding of the scope of the cost tabulation. This paper deals specifically with the mining and crushing methods employed by Victor Plaster, Inc., Victor, Ontario County, N. Y. The maximum annual production capacity of this company is 150,000 tons of crushed gypsum. The methods and practices employed arc typical of those followed in the gypsum mines in western New York State. The shaft is, perhaps, the deepest and the thickness of the gypsum mined is above the average for the section.

Jan 1, 1937

By F. R. Cattoir

The Federal Bureau of Mines refined chromium from an aqueous electrolytic process in molten sodium chloride-chromium chloride electrolytes. Oxygen and nitrogen contents were reduced by a factor of 10 to 40, but most other impurities were little changed. The product usually contained a little more iron than the feed. Since iron was entering the bath from the iron pot and the graphite liner at a nearly constant rate, contamination of the chromium deposits by it was more serious at low currents and deposition rates. A few runs in an iron cell with a nickel liner yielded chromium containing one half as much iron as the feed, but up to 1.5 pct. nickel. In all cases the anode feed lay in the bottom of the container, which itself was used as the anode connection. With a 12-in. cell, variations in applied voltage from 0.05 to 1.5, in current from less than 10 to over 100 a., and in initial cathode current densities from less than 100 to over 2,000 a./sq.ft. had little or no effect upon the analysis of the metal produced) except for iron content. Changes in bath analysis from 3 to 11 pct. chromium were also without effect. These changes did bring about large differences in the physical forms of the crystals obtained. The thick heavy crystals produced at low voltage and current contained voids which made them difficult to leach free of chlorides. Easiest to leach were the thin leaf-like crystals obtained at around 1 v.

Jan 1, 1960

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

By S. M. Shelton

The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.

Jan 1, 1941

By S. M. Shelton

[The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.]

Jan 1, 1941

By A. T. Coumbe

The first national survey covering sales of fuel oil by States and principal uses was made in 1926 by E. B. Swanson of the Bureau of Mines (then under the U. S. Department of Commerce) under a cooperative agreement with the American Petroleum Institute. This annual study, covering the market for fuel oil, was made through 1930 with the financial help of the institute bat has since been continued by the Bureau up to the present time. The scope and coverage of the survey have gradually changed over the years as new uses for fuel oil have been found and new products have come into importance resulting in market expansion. Range oil (No. 1 fuel oil or kerosine) came into use for cooking and space-heating daring the depression era in New England, and it was first reported as a total in the 1931 survey. In 1934 the sales were compiled on a State basis. State totals for distillate fuel oil, Diesel fuel, and residual fuel-oil sales were first shown for 1934 and by principal uses and States in 1937. Kerosine deliveries by States and main uses were also released for the first time in 1937.

Jan 1, 1952

By Frank E. Chase

Kettlebottoms are columnar masses of rock--the preserved casts of ancient tree stumps--embedded in coal mine roof strata (of which they are a part). Because unsupported kettlebottoms can detach from a mine roof without warning, they are a hazard to miners. The primary objectives of this investigation were (1) to better define and describe kettlebottoms and (2) to evaluate kettlebottom support techniques in terms of safety and effectiveness. A telephone survey of mine operators, interviews with Mine Safety and Health Administration (MSHA) personnel, and underground mine visits were conducted in Pennsylvania, West Virginia, and Kentucky. Information gathered during this investigation indicates that the size and frequency of kettlebottoms in mine roof are dependent upon past geologic events and biological processes active during the deposition of roof sediments. To ensure the safety of mine personnel, all undermined kettlebottoms should be supported. The roof should be bolted next to kettlebottoms less than 3 ft in diameter, close enough to allow a portion of a wood or steel header to be extended beneath each kettlebottom for support. Two bolts and a wood plank or steel strap should be employed to support kettlebottoms over 3 ft in diameter.

Jan 1, 1983

By R. W. Stahl

Coal mining has been revolutionized by the continuous miner. This machine has replaced, or has combined into 1, 3 former operations: Cutting, blasting, and loading. During the 25-year period before this machine was introduced, advances had been made in transportation, but the actual "coal getting" remained virtually the same. As frequently occurs, the multiple-purpose continuous miner introduced a new hazard--more rapid liberation of methane. The coal output formerly obtained from 10 to 20 working places might now be obtained from 1. It is true that circulation of air was generally increased; but the bulk of this machine virtually precludes continuous flow of air across the face, where gas may accumulate. Apprehension about this possible hazard led the Bureau of Mines to test face atmospheres during operation; and Report of Investigations 5288, Methane Buildup During Cutting and Continuous Mining Operations (published in 1956), presents proof that real danger may be present in many otherwise well ventilated mines.

Jan 1, 1958

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By O. M. Schaus

The following is a description of the methods employed at the Eureka-Asteroid mine, which is situated on the Gogebic range, at Ramsey, Mich. The mime is operated by the Castile Mining Co. under the direction of Oglebay Norton & Co. This paper has been prepared in accordance with an outline furbished by the United States Bureau of Mines, and in one of a series, on mining methods and costs covering the principal minim operations throughout the United States. ACKNOWLEDGMENTS The author acknowledges the assistance of the mining organization of the Castile Mining Co. in the preparation of this paper.

Jan 1, 1930

By R. H. Dickson

This paper, which describes the milling practice of the Verde Central Mines, Inc., is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. GENERAL DESCRIPTION The Verde Central concentrator is located in Walnut Gulch, about 1 mile west of Jerome, Ariz., and on the Jerome-Prescott highway. It is about 1,000 feet distant from the main shaft of the Verde Central mine and treats ore from this mine only. The mill is connected with the main shaft of the mine by a 24-inch gave railway, over which the ore is hauled in 5-cubic yard capacity, rocker, side-dump cars, by a 3-ton Brookville gasoline locomotive.

Jan 1, 1931

By C. G. Storm

Permissible explosives are those that have passed the tests pre- scribed by the Bureau of Mines for explosives intended for use in coal mines, and are therefore recommended by the bureau as suitable for this class of work when used under the prescribed conditions. The tests for permissible explosives and the conditions prescribed for their use are described in Miners' Circular 6 of the Bureau of Mines. Up to June 1, 1915, 168 explosives had been classed as per- missible explosives; 133 of them were then on the bureau's "per- missible list" and 35 had been withdrawn by the manufacturers. In addition to the required physical tests, each explosive is sub- jected to a complete chemical examination in order that its exact composition may be known and also that the composition of future samples of the same explosive collected in the field may be compared with that of the sample which originally passed the bureau's tests, for by such comparison it may be possible to ascertain whether or not the explosive as supplied to the miner is still "permissible." This bulletin is published primarily for the purpose of informing manufacturers of such explosives as to the methods used by the Bureau of Mines in the analysis of samples received for tests to determine their permissibility. Such information may be of value in cases of possible controversy over the results obtained in the analysis of a field sample as compared with those obtained in ana- lyzing the sample originally tested by the bureau. Also, a descrip- tion of the methods used by the Bureau of Mines in the analysis of explosives should be of assistance to the many chemists engaged in similar analytical work.

Jan 1, 1916

By P. M. Ambrose

This report describes an accident, which took place in the Chemical Corrosion Laboratory at the College Park, Md., Station of the Federal Bureau of Mines. The accident occurred while Walter L. Acherman, chemist, was performing a routine manipulation during a corrosion experiment involving commercially pure titanium and red-fuming nitric acid. There was a sudden and very violent reaction, and a large quantity of acid was thrown in the face and over the body of Acherman, causing serious injury. L. B. Golden, chief of the Chemical Corrosion Section, was exposed to nitric acid fumes during the ensuing rescue and first-aid operations and died on January 25, 1954. According to the medical report, the direct cause of Mr. Golden's death was pulmonary edema and confluent bronchopneumonia; the contributary cause, was inhalation of fumes from red fuming nitric acid. The following employees of the College Park Station contributed to this report by supplying information on the accident and assisted in the rescue operation: L. B. Golden, chief, Chemical Corrosion Section; T. E. Green, chemist; Robert Warf field, chemist; L. A. DeVivo, laboratory mechanic; D. W. Chalkley, laboratory mechanic; E. H. Neagle, laboratory welder; and R. L. Heath, laboratory general mechanic.

Jan 1, 1955

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010

By L. B. Pankratz

Thermodynamic data on the sulfides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H°298 -(G° - H°298)/T, ?Hf°, ?Gf°, and log Kf are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically.

Jan 1, 1987

By J. S. Dunning

The objective of this research by the U.S. Bureau of Mines was to determine the effects of AI additions on the sulfidation resistance of Fe-Cr-Ni alloys. A series of Fe-Cr-Ni alloys with and without -additions of 4 pet AI were tested in a wet S vapor atmosphere at 677 C. A study of the morphology and composition of corrosion scales indicated a different corrosion mechanism for AI-free alloys compared with AI-containing alloys. Aluminum-containing alloys formed a compact, tightly adherent layer at the metal-scale interface that reduced corrosion rates by a factor of 3 to 10 compared with that of AI-free alloys. The thin, adherent AI-containing scale limited inward diffusion of 0 and S to the base metal and outward diffusion of Ni from the base metal. Aluminum-containing alloys formed a three-layer scale in oxidizing-S environments, while AI-free alloys formed a less protective two-layer scale.

Jan 1, 1989

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of underground mining conditions on the activation of automatic sprinkler heads. Sprinklers were exposed to liquid fuel fires in a rectangular tunnel at airflows of 0, 45, 90, 150, and 250 m/min to determine the effect of ventilation and fire size on the time to activation. As the airflows were increased, the time to activate the sprinklers for a given fire size increased. Also, as the fire size increased, the activation time decreased. Temperature profiles of the tunnel showed that the maximum temperature near the roof was shifted downstream as the airflow increased. Experiments to determine the effect of rated activation temperature and response time index (RTI) value on activation time showed that the time to activate increased with increasing activation temperature, and decreased with decreasing RTI value. Exposure to the mine environment showed little effect on the activation times in large-scale experiments, and no significant effect in laboratory experiments. The results showed that airflow can have a significant effect on the activation times of automatic sprinklers. This needs to be considered in the design of effective sprinkler suppression systems for ventilated areas.

Jan 1, 2010

By J. A. Eisele

The Bureau of Mines is investigating the recovery of alumina from domestic nonbauxitic resources, including anorthosite. The United States has large reserves of anorthosite, but its aluminum content is less than 50 pct soluble in acid, unless a source of fluoride is added to the acid. A flowsheet that includes leaching with HCl and fluoride followed by crystallization of AlC13.6H20 from the pregnant liquor by HCl gas injection was designed. Approximately 90 pct of the aluminum values were recovered from the anorthosite when a ratio of 0.14 mole of fluorine per mole of aluminum was used. Sodium chloride is cocrystallized with the A1C13.6H20 but is removed by water washing of the Al203 product. A material balance is given based on results of laboratory studies of the unit operations.

Jan 1, 1983

By D. G. Kesterkel

Low-melting thoriurnrbase binary alloys or metal solutions were prepared by two different techniques involving the electrolysis of ThO2 dissolved in fluoride melts. Experiments were performed at 950° to 1,250° C using electrolytes containing ThF4 and various alkali and alkaline earth fluorides. In the first method, electroreduction of ThO2 and deposition of thorium on a nickel or iron cathode formed a molten alloy that dripped off and collected on the bottom of the cell, or in a tungsten cup. An electrocodeposition technique was used to prepare thorium-base alloys or solutions containing nickel, iron, chromium, or manganese. Electrolytic reduction of the component metal oxides and simultaneous deposition of the two metals on a tungsten cathode yielded a liquid alloy product. Complementary experiments were performed on the fused fluoride electrowinning of dendritic thorium from Th02 at 1,075° to 1,200° C in which thorium crystals were recovered and arc-melted into buttons. Major contaminants were aluminum, carbon, copper, iron, oxygen, and silicon, totaling 0.2 percent.

Jan 1, 1966

By William D. Monaghan

The U.S. Bureau of Mines evaluated a teleoperated continuous mining machine for deep mining in thin-seam applications as low as 1 m. Teleoperation increases the safety of mining machine operators because it removes the operator from the face, an area of immediate hazards to safer outby locations. By using teleoperation, the miner can avoid many including unexpected roof falls that can maim or kill miners instantly, methane and coal dust explosions that can be ignited with just a small spark or flame, adverse health effects from miners breathing coal and silica dust, adverse long-term inner ear damage from loud noise pollution, and other hazards related to heavy mining equipment moving about in confined underground roadways. This report presents the surface evaluation results of a teleoperated control system.

Jan 1, 1994