Search Documents

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION The investigation of the general hazards of combustible gases and vapors in manholes owned by the Edison Electric Illuminating Co. and the study of methods for eliminating these hazards, conducted by the Bureau of Mines, the Edison Electric Illuminating Co. of Boston, and the Boston Consolidated Gas Co. since 1929, was continued during 1933.From May and through December 1933 these tests were supplemented by a study of the manholes of the New England Telephone & Telegraph Co. The test crew was under the direct supervision of John Campbell, superintendent of the Special Service Department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Boston Consol¬idated Gas Co.The procedure of sampling manhole atmospheres and of shipping the samples to Pittsburgh was the same as that used heretofore. In previous reports the relative explosibility of the samples was calculated by adding the percentages of the illuminants, hydrogen, carbon monoxide, methane, and ethane, dividing the total by 6.5, and multiplying by 100. Experience has shown that the factor 6.0 is more nearly correct; therefore, this has been used in calculating the relative explosibility of all the samples listed in appendix A and B of this report. If gasoline vapor is present a smaller factor must be used.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of W. C. Bayliss, president of the Edison Electric Illuminating Co. of Boston; W. C. Beckjord, vice president and general manager of the Boston Consolidated Gas Co., and A. C. Fieldner, chief engineer, Experiment Stations Division, United States Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department of the Edison Electric Illuminating Co., cooperated heartily in furnishing both men and information for the work."

Oct 1, 1934

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

By R. Havens

During investigations of the occurrence of manganese in the western United States in the early 1940?s, examining engineers of the Bureau of Mines collected samples from seven claims and mines in southern Arizona. For convenience in reporting the results, the work on the properties is grouped in three districts. As the ores were too low grade to be acceptable to producers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The San Fernando group is about 10.5 miles south of Patagonia in the Harshaw mining district. G. T. Humphries and D. Alonso held an option on the property, which was owned by H. Bender. Two samples were taken; 1 was a picked sample and the other a representative sample of ore as exposed in the mine.

Jan 1, 1954

By F. D. Everett

The Burgin shaft of Bear Creek Mining Co. near Eureka, Utah, was sunk during 1956 and 1957 as part of an exploratory program, searching for lead, zinc, copper, silver, and gold ore bodies hidden from the surface by several hundred feet of volcanic rocks. This paper describes the sinking methods and operating practices of Centennial Development Co., contracting firm for Bear Creek Mining Co., in sinking a 3-compartment vertical shaft 1,100 feet. The operation featured the Cryderman positive-action, clam-type shaft mucker. The shaft was completed in 142 days by a shaft crew of 10 men and a top force of 10 men, including supervision.

Jan 1, 1959

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By A. M. Evans, J. H. Soulé

"INTRODUCTION Deposits of iron ore in Cherokee County, Tex., have been worked at various times in the pact, and the ore has been smelted in small local blast furnaces.Recently it was proposed to establish a charcoal blast furnace with a wood distillation plant to produce charcoal for fuel and byproducts. Financial assistance from the Reconstruction Finance Corporation was sought by George Easley and associates to enable them to purchase, move, and erect the furnace and build the required accessory plants. The furnace was to be moved from Pembroke, Fla.In August 1941, the Bureau of Mines was asked by the Office of Production Management to check the development work of Easley and associates and to ascertain (1) the iron-ore reserves, (2) the cost of mining ore and delivering it to the blast furnace, and (3) the grade and character of the ore. The Bureau of Mines was advised, while the investigation was in progress, that approximately 1,000,000 long tons of measured reserves would be sufficient to demonstrate the feasibility of operating the properties.Although deposits of iron ore are widely distributed in Cherokee County, only the Pryor Mountain, Banks and Cherokee, J. P. Acker, and Citizens State Bank tracts were sampled thoroughly by the Bureau of Mines. The iron-ore rights on these are owned by the New Birmingham Development Co., the Cherokee Development Co., or by individuals. Options to lease the ore rights were obtained by Easley, who obtained options on the Hawes Peach Orchard and Bradford tracts, also, which were examined only cursorily by the Bureau."

Aug 1, 1947

By J. P. Morris

A diphenyl ether calorimeter for measuring high-temperature heat contents of ferrous alloys and iron-and steelmaking slags was constructed and calibrated with specimens of molybdenum, alumina, and platinum that were heated to temperatures ranging from 1,720° to 1,875° K. The standard deviation of the calibration measurements was 0.37 percent. By measurements of the enthalpy of delta and liquid iron, the heat of fusion of iron was found to be 3,298 ±100 cal per mole.

Jan 1, 1966

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By Michael J. Friedel

The integrity of mine structures, such as the roofs, ribs, face and supporting pillars, is difficult to assess beyond the exposed surface. To mitigate potential rockfall hazards, the U.S. Bureau of Mines is assessing the usefulness of Rayleigh wave dispersion analysis to detect damage and stress-relieved zones in mine structures. Classical surface wave dispersion modeling is utilized at both laboratory and field scales in damaged and undamaged material to assess the integrity of a mine pillar and roof. To more fully exploit Rayleigh wave propagation characteristics, derivation of a novel dispersion parameter was conducted using a convolutional model. The development of a suitable Rayleigh wave dispersion system based on insight derived from forward modeling is presented. The application of inverse modeling for damage and stress assessment in the mine environment is also discussed.

Jan 1, 2010

By A. R. Mumford

During the course of an investigation conducted by the fuel section of the Bureau of Mines , on a hand- fired return- tubular boiler plant , it was found that the average cost of fuel to produce 1,000 lb. of steam was $ 0.5287 . Tests conducted after some simple changes had been made in the furnaces , and in the control of the boilers , showed the previous high cost of fuel per 1,000 lb. of steam could be reduced to the reasonable figure of $0.3540 , or the equivalent of over 30 per cent saving in fuel cost .

Mar 1, 1923

By Joseph J. Wallace

1. The investigation shows that there are two coal beds of major importance in Perry County from the standpoint of present production -Flag and Fire Clay -and two beds of minor importance -Haddix and Hindman. The Flag and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 840 million short tons as of January 1, 1954. Of this total, 720 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1954

By R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 2010

These tentative inspection standards have been prepared as a guide for the Federal inspection of the anthracite mines of the United States. The Federal Coal Mine Inspection Division is not a mining-law-enforcement

Jan 1, 1943

By D. Harrington, W. J. Fene

That fatalities from mine explosions can be very much reduced from the experience of past years if not wholly eliminated was fairly well demonstrated during the fiscal year ended June 30 , 1934 , there being only 28 deaths in the United States from explosions during this period . This is by far the lowest number of fatalities from explosions in the history of coal mining in the United States insofar as records are available . Although the frequency of occurrence of explosions has not decreased greatly during the past 6 years , there has been a marked decrease in severity , indicating that our coal -mining people are taking more effective precautions to prevent the spread of explosions . Pennsylvania is a good example of what may be done in reducing both the frequency and the severity of explosions ; by the adoption of up- to - date safety measures , Pennsylvania bituminous mines now have the enviable record of only one major explosion disaster in more than 5 years , and the one major explosion which did occur cost but 7 lives although 277 persons were exposed ; their lives were saved because rock- dusting prevented the spread of the flame and violence . Many of our other mining States are making definite progress in working mines without disastrous explosions and fires ; some of these , like Alabama , West Virginia , Indiana , Wyoming, and others now operating with few , if any , explosions , have had anything but a favorable record in the past .

Jan 1, 1935

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

Consumption and intensity of use trends for twelve metals, by industrial end use, were estimated for 1972 through 198Z. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following four of the twelve metal increased from 1972-82 as follows: aluminum, 1.00 percent; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83 percent; titanium, 7.82 percent; and tungsten, 6.09 percent. Consumption. for the remaining eight metals decreased at average annual rates ranging from 0.58 percent (copper) to 5.37 percent (manganese).

Jan 1, 1986

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By E. C. Fitch

This report discusses fire-resistant hydraulic fluid safety from three different directions. First, results of a survey prepared for the Fire Resistant Hydraulics Journal by the staff of the Fluid Power Research Center are analyzed. Second, operational limitations of fire-resistant hydraulic fluids are examined. Finally, laws and standards of various foreign countries are investigated. Three conclusions are derived from a close study of fire-resistant hydraulic fluid safety from these three directions. First, a significant number of experts in the fluid power industry are no in agreement about aspects of fire-resistant hydraulic fluid fire-resistance and toxicity. This indicates a need for more in depth research. Second, the use of fire-resistant hydraulic fluids involves a compromise between the decreased fire hazards and increased toxicity and machine incompatibility problems. Finlly, major foreign governmental agencies have thorough laws and standards concerning fire-resistant hydraulic fluids. These laws and standards may provide a solid framework for further international research into fire-resistant hydraulic fluid safety.

Jan 1, 1979

By G. R. Hopkins, E. W. COCHRANE

The number of completed petroleum refineries in the United States continued to decline in 1937 , but the total capacity to process crude oil continued to increase . These facts were ascertained in the Bureau's annual canvass of refinery capacity as of January 1 , 1938 . Several important changes were made in the census questionnaire for January 1 , 1938 . First , the basis of reckoning cracking capacity was changed from cracking stock charged to cracked gasoline produced . Although this is a definite improvement , in that it is no longer necessary to consider the yield , it is unfortunate that the data for January 1 , 1938 cannot be compared with cracking - capacity statistics since 1925. Other changes or additions included separating capacity at operating plants into that actually operating and that closed down ; collecting data on capacity added or retired during the previous year ; breaking down idle capacity according to physical status ; and separating new capacity into that built for replacement and that built to augment existing capacity . Prior to January 1 , 1938 , the total capacity of an operating plant was listed as " operating " even though some stills might have been closed down ; furthermore , the only capacity reported as being under construction was that of new plants that were being built on January 1. To make the statistics clear , the totals for the United States as of January 1 , 1938 , are given on both the old and the new bases . On January 1 , 1938 , there were 551 completed plants compared with 572 the previous year . Ten new plants were under construction on that date compared with 11 the year before . The greatest number of completed plants recorded was 632 on January 1 , 1936 ; since then , competitive conditions , particularly in the East Texas field , have been instrumental in reducing the number of small independent plants . The total crude- oil capacity of the completed refineries on January 1 , 1938 , was 4,351,151 barrels , of which 3,970 , 196 barrels ( 91 percent ) represented the capacity in actual operation and 380,955 barrels ( 9 percent ) was shut down . The " shut -down " capacity ( 199,875 barrels on the old basis ) was the lowest since pre- depression days , chiefly because numerous idle East Texas plants were removed from the list . The new method of compiling the statistics sheds considerable light on excess crudeoil capacity , which has been the subject of considerable speculation in recent years . The highest daily average crude runs to stills reached in this country was about 3,460,000 barrels in September 1937. At that time , the total crude - oil capacity was about 3,925,000 barrels . This indicates that at peak operation the excess capacity was somewhat less than

Aug 1, 1938