Search Documents

By Vic Sterner

As cities and towns continue to grow, the need to install sewer, water, gas and other utilities becomes a necessity and the blasting of trenches for these service lines probably constitutes one of the most important forms of blasting in built-up areas. There f o re, understanding how explosives can be safely used in the most efficient manner is of prime importance. The need for protection against flyrock must be emphasized. The first consideration is that all explosive c h a rges should be located well down in the blastholes. The golden rule is to ensure that the depth of top stemming is never less than the burden on the hole. In the case of shallow holes, the minimum depth of stemming should not be less than 18 times the charge diameter, if airblast and flyrock are to be controlled. If there is a doubt, then additional cover and/or blasting mats should be used. Putting too much burden on blastholes is another possible cause of flyrock and raising ground vibration levels. Overburdening of explosive charges will also result in the blastholes not breaking to grade. This in t u rn re q u i res additional drilling of shallow holes down in the trench to achieve grade, thus further increasing the h a z a rd of flyrock .

Jan 1, 2004

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991

By W B. Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire. Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1994

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By John Brennan

OK, I’ll admit it: I’ve always been a big Monty Atwater fan. Not only is the man credited with being the father of modern avalanche forecasting and safety in the United States, but he is also responsible for developing the avalauncher. Through its more than 40-year history, the avalauncher has gone through many changes yet continues to prove its worth in avalanche mitigation work.

Jan 1, 2007

By G. Adderley, A. Wetherelt

The problems of poor drilling in underground operations have been highlighted on many occasions. Incorrect collaring and poor angular deviation can all lead to an increased block size, dilution, over-break adding to both cost and time, while in a tunnelling operation sidewall damage and a poor percentage pull from a blasted round has similar consequences. This paper sets out to further investigate the ability of the laser scanner method of obtaining drill hole deviations and collaring errors at the face as described by Wetherelt and Williams (2006). Tests were carried out to compare measured inter-hole burdens from this method in comparison to that obtained using a total station survey. To investigate the ability of these methods to accurately determine drilling errors, a field test was carried out through an analysis of a series of pre-drilled blast holes of known inclination and direction. A time-motion study was also conducted for a varied number of holes to assess the usability of each method. In line with current research into blast vibration being undertaken at the Camborne School of Mines, 6 cut blasts were carried out to establish the effect of poor drilling on a blasts success to see whether an increased burden at the toe of a hole had an influence on vibration.

Jan 1, 2009

By D. S. Scovira, T. Gustavsson

Exiting WW2 (mid-1940s), the potential of nitrates (ammonium nitrate, calcium nitrate, sodium nitrate) and hydrogen peroxide for application as a commercial explosives for mining, construction, and other industrial purposes both became known. The technology stream advanced the development and uptake of nitrate based explosives to the point that they are the current global standard for blasting. Today, environmental issues are shaping the strategic agenda across various industries. Most global mineral resource, construction houses, and explosive manufacturers have publicly announced ESG carbon reduction commitments in support of COP26 Net Zero 2050. The mid-2010s saw a renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the early 2020s provided additional impetus to investigate hydrogen peroxide based explosives for industrial use. Hypex Bio has recently pioneered the formulation, manufacture, and end-use delivery of a Hydrogen Peroxide Emulsion (HPE) on an industrial scale. The HPE is composed primarily of hydrogen peroxide (H2O2) plus a lesser amount of fuel and emulsifier phase. The base HPE is produced in a low energy intensity modular plant using industry proven mixing techniques. The base HPE is a white, highly viscous emulsion that is similar in consistency to base nitrate emulsions. To enable end blasting use, a mobile charging unit gases the base HPE to a detonable density. The HPE is compatible with current priming and initiation systems. Hydrogen peroxide explosives offer a significant reduction in total carbon emission as compared to nitrate based explosives. The production of ammonium nitrate (AN) emulsion is energy-intensive and not carbon neutral. Based on the EU Average and for the oxidizer phase only, 1 kg [2.2 lb] of AN emulsion emits 2.3 kg [5.1 lb] of CO2 as compared to the production of hydrogen peroxide emulsion that results in 0.23 kg [0.5 lb] of CO2. This is a difference of 90%. HPE contains no nitrates and does not generate post blast nitrous oxides (NOx). HPE generates no aqueous nitrate or ammonia pollution and is a solution to meeting increasingly regulated mine site water discharge limits. Hypex Bio recently conducted a successful underground HPE evaluation with a major mining company in Sweden. HPE blast designs were the same as those done with nitrate based emulsions. Rock breakage, advance, muck displacement, and excavator performance were equivalent. Ventilation and re-entry times were reduced. The mining company has expressed further interest in assessing HPE and is demonstrating industrial leadership by exploring this transformative explosive technology

Jan 1, 2024

By C B. McCampbell, R W. Jr Bickes

Sandia National Laboratories has developed a semiconductor bridge (SCB) igniter for the ignition of a variety of explosive materials. When subjected to a low-energy current pulse, the bridge bursts into a plasma causing rapid ignition of the explosive material pressed against the bridge. Despite the low energies required for ignition, SCB components have proven to be explosively safe, meeting both no-fire and electrostatic discharge (ESD) safety requirements.

Jan 1, 1991

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Kagan Ozdemir, Adiguzel Deniz

This paper presents the results of ground vibration measurements induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel which has been driven at a depth of approximately 20-40 m deep under a highly urbanized region of Istanbul city in Turkey. This tunnel is being constructed by a joint venture group. The formation encountered during the construction is classified as hard and strong rock by laboratory and field tests performed by the joint venture group. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S4 shaft tunnels and S12 shaft tunnels of this tunnel route, ground vibration components were measured carefully by using four vibration monitors (Instantel Minimate Plus model) during the advancement of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighbouring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 114 records at S4 shaft tunnels and 79 records at S12 shaft tunnels were analysed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for different rock units (diabase and arkose) and suggested for the test sites in order to estimate particle velocity of the ground vibrations.

Jan 1, 2007

By Tamara Whitaker, James Gunderson, Ruilin Yang

This paper presents the results of a vibration control project conducted in soft overburden at a surface coal mine located in the western United States. The study uses near-field blast vibration monitoring, analysis and modeling techniques developed in house. Accelerometer-equipped seismographs were utilized for near-field vibration monitoring and analysis. Vibration control was achieved through field data regression as well as vibration modeling using the multiple seed near-field blast vibration model (Yang and Scovira, 2007). The regression was conducted between peak particle vibration parameters and the minimum scaled distance per delay. From the regression analysis, the curves of upper bounds for peak particle vibration parameters and charge weight were developed. The dominant frequencies of the blast vibration were also addressed in this project. The regression curves and near-field vibration model guided the blast design to control blast vibration for maximizing the recovery of coal and maintaining mine productivity.

Jan 1, 2008

By Ron Beeslaar, Tony Rorke

The Professional Blast Manager is a blast design tool that has been developed in South Africa. It is aimed at mining and civil engineen, blasting contractors and mine planning engineers. The code can be used as a stand-alone package or be combined Into complex mine information systems.

Jan 1, 1998

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation.

Jan 1, 2001

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009

By Iván E, Alex Araya Jofre, Jean Guiroux Toro, Eduardo Valdés Guerra

Currently, it is important for companies to have controlled mining operations and adhere to production schedules. To achieve this, one of the key factors is maintaining high reliability in the P&T process, primarily the opening of ore stope, which could be delayed due to any unplanned or uncontrolled problem. These ore stope opening processes, whose main activity is generating free face, are a very important pillar for future mine planning. The possibility of ensuring their opening brings a series of downstream benefits: safety, economics, productivity, and compliance and adherence to plans. The process under discussion consists of developing free faces in a single blasting event. This will help us leverage greater reliability for overall production operation plans, reduce construction times, and open up opportunities for downstream improvements in the production process, considering technical factors in P&T designs. This study presents a developed methodology and shows the results of its implementation in ten (18) single-event free face blasts. The analysis includes cavity geometry, geology, rock qualities, drilling deviations, and the blasting strategy implemented for each event. The methodology used considered material fluffing processes, the actual drilling trajectory, the initiation sequence, QA/QC during explosive loading, monitoring instrumentation (vibrations), and VOD recording, among others. As a result, out of a total of 18 free-face events blasts in a single event, 16 were successful and two achieved 90% efficiency, reducing the stope's production start-up time by 50% compared to current operations. By implementing free face blasting in a single event, there are savings in operating costs, increased productivity of the mining equipment, and improved adherence to production plans. For applications with greater heights of free faces, where blasting cannot be carried out in a single event, we should consider performing them in two stages using wireless detonators already available on the market for mining operations.

Jan 26, 2026

By Dale S. Preece

"Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control. Three-dimensional computational capabilities in terms of software, material models and computer speed have recently made possible the computer simulation of multiple blast holes in a bench configuration with precise delay timing between holes. Some of the key physical phenomena enabled by precise delay timing include: 1) collision and interaction of stress waves produced by adjacent blast holes, 2) reinforcement of stress waves from multiple holes as they reflect from the bench face and ground surface, 3) reflection of stress waves from “dynamic free surfaces” created by previously detonating holes, and 4) deformation induced fracturing, cracking and fragmentation. Simulating rock blasting in 3D has shed light on the physics involved and is resulting in an evolution of our understanding of fragmentation mechanisms. Routine use of these 3D computational tools will result in a much better understanding of the complex physics set in motion by the rock blasting process and allow predictionof improved blasting."

Jan 1, 2009

By Simon St. John Tose

We have had a long history in supporting the development of training material to ensure “safe” blasting. This has been provided as both significant technical guidance to the industry and input into the development of the new industry surface rockbreakers or shotfirers qualification in South Africa (RSA). The learning material supplied to the industry is based on both a classroom knowledge component and an assessment on the practical application of the learning by the trainee blaster on the job under the supervision of the appointed blaster. This training includes all blasting applications which can often extend beyond the “normal” mining environment of open pits, underground and quarries into civil applications such as trenches, blasting close to private buildings, public roads, pipelines, power lines, swimming pools and the removal of concrete structures and building demolitions etc.

Jan 1, 2013

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By Harry L. Siebert

Pre-splitting was substituted for line drilling to achieve stable rock slopes and reduce excavation beyond the pay line on a Connecticut highway project in 1962-63. Changes have occurred in developing rock slopes that were not foreseen by Alan Bauer and Jim Scott who in the early days understood the relationship of explosive energy to stable slopes. Cushion blasting as currently used produces slopes designed to blend or complement the natural landscape with slope holes detonated after the main body of holes. Pre-splitting is the opposite. The best results have been achieved by detonating the pre-split line of the holes first to allow readjustment of the slope plane fracture and a separate blast for the main body of loaded holes.

Jan 1, 1998

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006