Search Documents

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By J. H. Morris, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Oxygen isotope analysis indicates that quartz, carbonates and muscovite could all have formed in near-isotopic equilibrium with the mildly saline H2O-CO2 ore fluid at 330 degrees C. Calculated values for O, C and S in the ore fluids imply derivation from a deep, homogeneous source region and are consistent with formation either as a direct or an indirect result of igneous processes. Values for delta-O18 plot a little outside the accepted magmatic range, but have almost certainly been modified by exchange reactions with wall rocks. These reactions were also the most likely cause of deposition of the ore constituents. The chemical and isotopic character of the fluid was similar to that in many Archaean and later mesothermal auriferous vein systems, especially the Mother Lode region of California. If the Southern Uplands-Longford Down accretionary complex conceals an Ordovician arc, the tectonic setting was also broadly comparable

Jun 19, 1905

By I. D. Nock, R. M. Parkin

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Knowledge-based condition monitoring of cone crushers). A large proportion of the electricity used by the quarrying industry is consumed in the comminution and sizing process. In most cases aggregate processing plants operate with minimum control features resulting in limited operational efficiency. Improved control is required to increase operational efficiency with concomitant savings associated with reduction in re-circulating load and improved resource utilisation. Development work has suggested that a combination of adaptive control and process condition monitoring could improve control of comminution plants. Many commercial process control and condition monitoring systems are available, but none were deemed suitable due to the domain specific characteristics of the application. An assessment of the particular characteristics of cone crushing concluded that the application was best suited to the use of small domain specific process control combined with bespoke condition monitoring. The processing power of the control system for the project is a function not of the academic requirement, but rather the economic and practical constraints imposed by the application. As a result of the constraints a high-end PC system has been designed in preference to a workstation. Within the research project work packages are sub-divided into novel wear sensor development, knowledge based control/condition monitoring and the investigation and mathematical modelling of the wear mechanisms inherent in cone crushing. Numerous strategies were considered to implement the control system outlined. The system currently under development is a modular design which utilises intelligent novel sensors to provide a variety of data inputs

Apr 1, 1994

By R D. Lama, A Misra

One of the major factors restricting an increase in the productivity of a longwall mine is lower productivity obtained in a development panel. There has been a significant improvement in gate road development, particularly in mines requiring high density roof and rib bolting within 2 m of the face. Advance rates have increased from an average of 3 m to 5 m per shift in 1985 up to an average of 5 m to 10 m per shift in 1991. In mines at shallow depths with reasonably good conditions the increase has not been that significant. Advance rates have increased from an average of 7 m to 12 ni per shift in 1985 to an average of 12 m to 15 m per shift in 1991. Compared to the United States' (US) development rates, these are much lower. Extensive research work has been carried out to minimise cutting, wheeling, support setting time, and to optimise pillar length to achieve maximum advance rates. Pillar optimisation is very important in order to expedite adverse rates. This paper investigates various development rate technologies, both present and future, and optimises pillars to improve these dev elupment rates. Pillar optimisation is based upon time and motion studies conducted at mines in the Illawara region of New' South Wales, Australia, and the basic tools of arithmetic.

Jan 9, 1996

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

By J. K. Brimacombe, F. D. Richardson

Studies have been made of interfacial turbulence occurring in reactions in which indium, zinc and cadmium, dissolved in amalgams, are oxidised into aqueous phases by ferric or mercurous ions. It has been found that this turbulence occurs when the concentrations of oxidising ions in the aqueous phase become sufficiently great. These concentrations are the same as those at which the mass-transfer coefficients in the aqueous phase increase sharply when both phases are stirred by gas bubbles rising through them. The effects of gas flow rate on the mass-transfer coefficients for zinc in mercury have been established, and the oxidation of pure mercury has been investigated. The relevance of the work to processes involving liquid metals is discussed

Dec 1, 1971

By P. J. Rowsell, M. D. Waller

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The applications of artificial intelligence systems in the upstream petroleum industry are reviewed. Particular emphasis is placed on current and potential applications in drilling engineering. Several recent advances in drilling technology have led to a large increase in the quality and volume of data available. This combined with the escalating cost, particularly of off-shore operations, is testing the traditional reliance on the skill and judgement of rig operators. AI systems offer enormous scope in enhancing and aiding the performance of these operations

Apr 1, 1994

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905

By G. G. Barbante

An understanding of the thermodynamics of smelting copper anode slimes is a prerequisite for improvements to the process. During slimes smelting, a silver-copper selenide matte is formed and subsequently oxidised to silver metal. As part of a series of investigations, molten silver selenide matte was oxidised at 1 100 degrees C with pure oxygen. The chemical potential diagram for the system was developed and used for qualitative prediction of the results of the experiments. A simple, computational thermodynamic model of converting is presented, the adjustable parameters of which were determined by matching the model with the experimental results. The practical usefulness of the model was demonstrated by predicting the effect on silver recovery of smelting temperature and of using either oxygen or air as the smelting gas

Jun 21, 1905

By P. A. Rossouw, G. A. Fourie

Several attempts have been made over the latter half of the twentieth century to devise a system for the classification of underground mining methods. None of these are found to be totally successful. A revised classification is suggested with three main categories being identified by reference to fill requirements, steep stopes and stratified geological environments. Methods always needing lasting mass or structure fill include methods with timber-structured stopes and those with mass-filled (or cut-and-fill) stopes. Methods associated with steep stopes are subdivided into steep-stope-specific caving and steep-stope-specific non-caving (or self-supporting) methods. Methods not in the first two categories, often used in stratified geological situations, are not necessarily restricted to stratified environments and include caving as well as non-caving varieties. This category is further divided into room-and-pillar mining, longwall and shortwall coal mining and the type of open stoping found in gold or platinum reefs comprising overhand, underhand and breast-stoping variations

Dec 1, 1996

By Qing Wang

In this method the state of an open-pit mine is represented by the number of benches that are mined in each predesigned mining phase (or pushback). Consequently, a specific mining schedule can be represented by a sequence of states which starts with the topography of the mine site and ends with the ultimate pit. For a given set of mining phases all feasible states are first generated and sequences of states are then evaluated for technical and economical feasibility. The best sequence, which gives the maximum net present value (NPV), is found by applying a dynamic programming optimisation algorithm. The algorithm also optimises the cut-off grade which satisfies the mill feed requirement for each planning period. It was found that the algorithm can be used not only for scheduling but also as an effective tool for analysing the effects of mining and milling capacities and cut-off constraints on the mining schedule and the total NPV. The algorithm, which was programmed in C, was successfully applied to a large Au-Cu deposit

Jul 1, 1996

By G. M. Zhao

The gasification of lump coke with CO2 was studied in a fixed-bed reactor. The effective diffusivity of the gas was evaluated from measurements of the reactivity of the lump coke, produced by BHP Steel in New South Wales, and from kinetic parameters that were determined from the reactivity of fine grains. The grain model of effective diffusion in porous media was adopted to express the gasification rate of the lump coke and was found to fit the experimental data well. The relationship between reactivity and textural characteristics of the coke was examined

Jun 18, 1905

By M. Moinpour, Y. K. Rao

The catalysed direct reduction of copper sulphide with carbon and lime was investigated in the range 850-1000 degrees C using Cu2S-CaO-C and Cu2S-4CaO-4C reaction mixtures. The effects of the catalytic additives K2CO3, Li2CO3, Na2CO3, NaF, Na2SO3 and the ternary eutectic (K,Li,Na)2CO3 were determined. Potassium carbonate, sodium fluoride and the ternary appear to be the most effective catalysts for the direct reduction process. The rate enhancement of the catalysed carbothermic reduction of copper sulphide in the presence of lime was explained in terms of the catalysis of the Boudouard reaction

Jul 1, 1991

By D. C. Bailey, D. I. Hodson

Paper presented at the annual joint meeting of the IMM and IMinE held in Harrogate, 31 January 1991. The Neves-Corvo copper-tin mine is the highest-grade large-tonnage copper operation in the world and is now arguably the most significant producing base-metal mine in Europe, rating in the top ten world producers of both copper and tin. A description is given of the initial exploration work and the development of the project from the orebody discovery in the Iberian Pyrite Belt of southern Portugal in 1977 to full operating capacity in 1990. The chronological account includes discussion of the main organisational, financial, technical and environmental decisions and of the various difficulties encountered, and the challenges of the future are identified. The project was brought in on schedule and within budget

Jan 1, 1991

By D. W. Taylor, I. W. Farmer, N. Mojtabai

Rittinger's and Bond's descriptions of rock crushing relate the energy input required to fracture rock and the surface energy required to form new fractures to the change in specific surface area of feed and product during comminution. The potential applicability of this approach to blasting is illustrated, using the results of data from bench blasting tests on Pinal schists and production blasting of Carboniferous limestones. The approach contributes to understanding of the mechanisms involved in blasting and to the design of test blasts. A modified form is presented of the relationship between blasting energy, specific surface area of the muckpile and a rock energy constant related to the discontinuity structure of the rock. The modified equation fits observed data and offers a simple basis for further experiments

Jun 19, 1905

By H. R. Thorpe

A floating gold dredge operating in coarse alluvial gravels of the Grey River on the west coast of the South Island, New Zealand, generated high concentrations of clay and colloidal particles in the dredge pond, which entered the groundwater system. Sampling was carried out at depths down to 20 m and it was found that variation of the length of the flow path occurred because of the movement of the dredge towards the piezometers. The alluvial gravels, the suspended sediments, the groundwater system and the water chemistry were all studied. Sediment concentrations were found to be highly variable with depth, but the relative concentrations in the depth profile were generally consistent as the flow distance shortened. The sediments were extremely fine and travelled further through the gravels than predicted. Comparison of field results with the available theory of deep filtration in clean beds of porous media gives some basis for estimating the behaviour of fine sediments in other alluvial systems

Jun 19, 1905

By A. P. Gize, J. F. W. Bowles, D. J. Vaughan, S. J. Norris

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Geological evidence from tropical laterites indicates clearly that platinum group metals are taken into solution and precipitated to form grains larger than those in the source rocks. Platinum and palladium move differentially in the surface environment, with Pt partitioning into soils and eluvial or alluvial deposits while Pd remains more mobile in natural waters. Natural organic acids, particularly humic acid, can interact with platinum-group elements and concentrate them even in areas where their content in rocks is very low. Experimental work has confirmed that Pt and Pd can be taken into solution by humic acid at room temperature and in geologically short time-spans. Solubility and deposition may be controlled by physicochemical conditions, reaction kinetics or an adsorption effect, or there may be two competing reactions, solubilisation assisted by organic matter and a kinetically slower metal precipitation

Apr 1, 1994

By A. H. G. Mitchell

Most, if not all, of the six recognised post-Cretaceous, predominantly andesitic mineralised belts in the region are now thought to be subduction-related magmatic arcs. The Inner Carpathian arc and the Eastern Bosnia or Drina-Rhodope arc host numerous vein and replacement deposits with epithermal features and Zn-Pb+/-Ag as the predominant economic minerals. In contrast, the south Apuseni Mountains have produced over 1 600 t Au from epithermal veins but very little Zn-Pb. Recent age determinations and geophysical data from the Baia Mare district of the Inner Carpathians suggest that mineralisation succeeded volcanism by 1-2 m.y. and accompanied crustal extension and the cooling of a large, mushroom-shaped pluton whose boundaries define the mineral district. In the south Apuseni district, mineralisation can be explained by mixing of meteoric with low-salinity metamorphic water expelled during intrusion of mafic rocks into the middle or lower crust. The more continental or cratonic crust in the Drina-Rhodope and Inner Carpathian arcs precluded the input of low-salinity, Au-bearing metamorphic water; the Zn-Pb deposits formed where convecting meteoric water mixed with saline water, possibly introduced through carbonate rocks in the basement

Aug 1, 1996

By J. S. Coats, G. E. Patts, N. Hughes

Conventional sampling methods are known to suffer from the variable loss of fine gold by elutriation. Freeze sampling yields representative and quantitative data that, when combined with information on the sedimentology of gravel-bed rivers, may facilitate the development of improved dispersion models for source detection. It is suggested that freeze sampling may have particular application to the orientation stage of a large gold exploration survey

Jan 1, 1991

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991