Search Documents

"A 3-dimensional finite element model for stress/stability analysis of rock excavations in underground mines is presented. Developed for use on personal computer under OS/2 operating system, the model employs the 8-node isoparametric brick element and accounts for such loading conditions as in situ stresses and gravity loading of the rock mass. In addition, modelling of backfill in mine stopes as in situ stress-free material is incorporated. Material failure is assessed by Mohr-Coulomb or Hoek-Brown failure criterion. A mine design example is presented to illustrate the potential use of the model as a tool for stope design.IntroductionNumerical modelling of mine structures has become a vital tool for mine design in recent years. The need to maximize ore extraction ratio and to reach deeper mineral deposits underground has led the mining industry to employ numerical methods of analysis to undertake complex ground control studies in order to better understand the ground response to mining excavations and to evaluate the ground support requirements. Thanks to the rapid developments in computer technology, it is now possible to perform very comprehensive analyses including, but not limited to, 3-dimensional, elasto-plastic, or large deformation or time dependent nonlinear analyses on personal computer.During the past ten years or so, many researchers undertook 3-D finite element analyses of rock mechanics problems in mining engineering. The following is only a sample review. For example, Chan'!' used three-dimensional finite elements to study the mechanical response of jointed granite during shaft sinking at the Canadian Underground Research Laboratory. Wang et al.(2) performed 2-D and 3-D finite element analyses of room-and-pillar mining system with flat and rolling coal seams. Thatejatu used three-dimensional finite element method to examine the problem of branching tunnels. Dolezalovaw used three-dimensional finite elements for the analysis of tunnel-face advance with partial excavation as well as full-face excavation in combination with rein for cement of the face by long anchors. Peili (5) used three-dimensional finite elements for the simulation of rock-liner interaction near the tunnel face."

Jan 1, 1992

By S. Hunt, S. Jayasekera, J. Kyle, N. Perera, K. Stone

A preliminary investigation has been conducted to determine the conditions for the precipitation of phosphate from the liquor produced after a hydrochloric acid pre-leach and rare-earth recovery from a rare earth containing fluorapatite concentrate from the Nolans rare earth deposit in the Northern Territory of Australia. The results show that at 50oC the phosphate can be precipitated in two stages using limestone to produce a Stage 1 precipitate containing most of the impurities including iron (94%), aluminium (92%), fluoride (98%), uranium (84%) and thorium (94%), followed by a relatively pure Stage 2 dicalcium phosphate precipitate (DCP) containing only 0.05% Fe, 0.05% Al, 0.1% F, 0.01% U, and <0.01% Th. The initial Stage 1 precipitate contained about 25% of the phosphate while the remaining 75% reported to the Stage 2 phosphate precipitate. Depending on the required radioactivity specifications, the amount of phosphate in the Stage 1 precipitate could be reduced. Reagent requirements were 11.4 kg limestone (as pure CaCO3) per cubic metre of solution for the Stage 1 precipitate and 39.7 kg limestone (as pure CaCO3) per cubic metre for Stage 2. The analysis of radionuclide balance indicated that radionuclides deported mainly to the final filtrate (86.4%) compared to Stage 1 precipitate (5.4%) and Stage 2 precipitate (8.2%). Settling and pressure filtration tests indicated the precipitates were both readily settled and filtered. The final moisture contents of the Stage 1 and Stage 2 precipitates were 62.5% and 49.3%, respectively.

Jan 1, 2014

By Carol Odell

This paper was prepared as a brief for Prospectors and Developers Association of Canada (PDAC) to guide input at a series of round tables carried out by the Federal Government in response to the 38th Standing Committee on Foreign Affairs and International Trade (SCFAIT) report, on ?Mining in Developing Countries and Corporate Social Responsibility?. This document mandate is to provide background information, analysis and recommendations on the practice of Canadian exploration and mining companies abroad. This research was based on 11 case studies of Canadian companies which have experienced conflicts or controversies overseas. All case studies were assembled through an extensive literature review of publicly available documentation and communications with representatives of the mining companies to assist in deepening the insights into the drivers of the conflicts and the needs of Canadian companies in similar situations. The case studies include both exploration and mining operations. Our analysis begins with the identification of general and case specific drivers of conflict/controversy in each case study. Company names are kept confidential and only anonymous results are presented. We make ample use of simple flow charts and schematic diagrams to explain how contextual drivers and aggravators and company drivers and mitigators play varied and interrelated roles in conflicts. The diagrams also illustrate the cumulative analysis of drivers including the linkages among drivers/aggravators/mitigators across different domains (social, governance, NGO/media and company). Finally, we discuss needs of companies and propose recommendations for addressing social responsibility and human rights concerns.

May 1, 2007

By L. C. Kitchener, K. Vollenwyoer

"This paper describes the development of an automated, 70-ton capacity, underground electric trolley truck at Inco Ltd. The purpose of the project is to provide a high capacity and high productivity haulage system to suit continuous loader applications in existing mining horizons where conveyor belt application is not immediately practical. IntroductionWith the start o f a program by Inco in mid-1983 to develop a continuous loader for bulk mining of our hardrock orebodies, the need for a rapid ore transportation system was recognized to match the increased extraction rates planned. Two methods were investigated, truck haulage and conveyor belt. As a result, a conveyor belt system has since been designed and installed with a continuous loader at Stobie Mine and an electric truck has been designed, fabricated and assembled, with shop testing underway. This paper deal s with the latter project. BackgroundMany existing mining horizons which could utilize continuous loaders do not have the straight runs required for conveyor belts. In these situations, truck haulage would be the only alternative of the other transportation methods that would be practical. In order to match the high productivity potential of the continuous loader, however, a more efficient trucking system is required than would be available with conventional diesel powered trucks or with electric truck designs commercially available, or under development. A higher capacity truck and an automated operation is necessary so that the application of additional units to suit increasing haulage distances matches loader output without reducing over-all productivity because of the need for additional operators.A first effort to work with a major electrical manufacturer was unsuccessful and resulted in a project delay of almost one year. In November 1984, an investigation into the concept was reinstigated with UTDC, and an agreement to start design was reached in April 1985."

Jan 1, 1988

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division&apos;s Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine&apos;s Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By D. A. MacLeod

DURING the past fourteen months, dust surveys have been made at thirty-six mines in the Province. These surveys are made to determine the concentration of dust in the mine atmosphere, the flow of air through the mine, the methods adopted to prevent the generation of dust, and the measures taken for its elimination. When high concentrations of dust are encountered, suggestions are given for its prevention ?and elimination wherever possible. Dust sampling is absolutely necessary to determine the effectiveness of any measure taken in the prevention and elimination of dust in the mine workings. Consequently, more time has been spent on this phase of the work than on any other. The apparatus used is the Devers circular konimeter and Zeiss microscope. At various mines, the Zeiss konimeter is used, and the dust counts taken by the two instruments have given results that are closely comparable; so much so that either instrument can be used with confidence and the results obtained will compare in accuracy with those obtained by the methods used in Ontario and South Africa. Before the Workmen&apos;s Compensation Act Amendment Act was passed in November, 1936, most of the mine operators were already keenly interested in the prevention of silicosis. This interest has been intensified at all the mines, and measures have been adopted to decrease the amount of dust in the mine atmosphere. Several operators have spent a large amount of time and money in bettering these conditions, and have met with decided success. Practically all others are adopting the known methods of prevention, suppression, and elimination of dust, that apply to their ?particular mines. To prevent the production of dust in underground workings should be the first, as it is the most important, aim, especially during the time the men are underground. An atmosphere free of dust cannot be obtained, but measures can be adopted to lower the concentration that is found? in the average mine.

Jan 1, 1939

By Dougla McDonald, Richard Poulin

"Most mine managers in Canada today will agree that one of the keys to mining efficiency and productivity is their human resources. A5 a result, many mines develop some sort of incentive designed to tap their employees&apos; capabilities to the fullest extent. Historically, the most common plans used have been ""piece-rate"" plans, where individual or small groups of miners are paid a financial bonus based on some measure of their productivity. Recently, however, incentive plans that take a more team-based approach have been developed in some Canadian mines. One such plan will be defined in this paper, and its popularity in the industry today discussed.Gainsharing PlansThere are two primary components to a gainsharing plan. The first is a cash incentive, which is paid to all employees and based on factors that are highly correlated with employee productivity, and key to the profitability of the mine. For example, the typical gainsharing cash incentive is based on the cost/unit of metal produced. Management (in consultation with employees in some cases) will establish the budgeted cost per tonne, and any savings in this amount is shared between the company and the employees. The second is a management philosophy and associated communication network, which is designed to foster an environment that encourages information exchanges, communication, participation, and trust between employees and management. The typical gainsharing communication network consists of two tiers of committees. The first, operational committees, include all employees working in the same department or departments which frequently interact. The employees meet monthly with management personnel to discuss problems encountered and brainstorm for solutions. In most cases, these committees will nominate a person in the group to structure the meeting to maximize its efficiency. The second, the screening committee, is a single group consisting of representatives from the various operational groups, whose primary job is to ensure that the plan is effective, and the objectives and results generated by the plan remain consistent with the mine objectives. In short, gainsharing plans tell employees that their bonus depends upon performance and then gives them the opportunity and incentive to affect that performance. The opportunity is provided by a communication network and positive management practices, and the incentive comes in the form of ""intrinsic"" rewards of participation and the ""extrinsic"" rewards of the bonus payments. Figure I will clarify the relationship between the intrinsic and extrinsic rewards."

Jan 1, 1995

By M. Celikin, M. Isac, R. I. L. Guthrie, S. Ge

Horizontal Single Belt Casting (HSBC) is a near-net-shape casting process in which molten metal is directly cast into thin strips, at high cooling rates (order of several 100°C/s), with the potential for high volume, friction-free, continuous production of metal strips. This casting process was used in the present work to produce strips of Al-Mg alloys in the AA5000 series, with additions of Sc and Zr. Such aluminum alloys show exceptional potential as a structural material for transportation/aerospace applications. To demonstrate the suitability of the HSBC process to manufacture competitive strip products of Al-Mg-Sc-Zr, the mechanical properties and microstructures of the strips produced using the HSBC process were compared with conventionally cast products. The effects of annealing on the mechanical properties of the strip-cast Al-Mg-Sc-Zr alloys were also investigated.

Jan 1, 2014

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By Robert A. Gault, T. Scott Ercit, Mehmet F. Taner

"Abstract -Vanadium mineralization occurs in oxide-rich horizons within the layered gabbro zones of the upper parts of the Bell River Complex, Matagami, Québec and the Lac Doré Complex, Chibougamau, Québec. The vanadium-rich horizons are well defined on the ground and in aeromagnetic surveys by their high magnetic susceptibility; consequently, magnetic susceptibility can be an indicator of vanadium mineralization. The main oxide minerals are ilmenite and titanian magnetite, containing 20% to 70% of volume and the ratio of titanian magnetite to ilmenite is relatively constant, ranging from about 1:1 to 2:1. Their sizes are less than 5 µm to greater than 1 mm to 2 mm, occurring as coarse- to medium-grained subhedral crystals intergrown with cumulate silicate minerals (plagioclase, pyroxene, etc.). Electron microprobe analyses indicate that the ilmenite grains are mineralogically and compositionally homogeneous and have low V contents (average 0.18% equivalent V2O5). In contrast, the titanian magnetite grains are inhomogeneous, consisting of trellisworks of ilmenite lamellae in Ti-poor, V-rich magnetite [less than 2 wt% TiO2, and 1.41% equiv. V2O5 (1.16% V2O3) for 20 analyses]. Thus, the magnetite is the principal ore mineral of vanadium; it hosts vanadium in the form of V3+, not V5+, as is commonly and erroneously reported. We have also devised a flowchart for the beneficiation of vanadium-titanium ores. Sommaire - La minéralisation de vanadium se trouve dans des horizons riches en minéraux oxydés de la partie supérieure des zones de gabbros lités des Complexes de la Rivière Bell, Matagami, Québec et du Lac Doré, Chibougamau, Québec. Des horizons riches en vanadium ont été bien définis sur le terrain et dans les levés aéromagnétiques par leur susceptibilité magnétique élevée; conséquemment, la susceptibilité magnétique est l’indicateur directe du contenu en vanadium. Les principaux minéraux oxydés sont l’ilménite et la magnétite titanifère, contenant 20% à 70% du volume et le rapport de magnétite titanifère à ilménite est relativement constant, allant d’environ 1:1 à 2:1. Leur dimension varie de 5 µm à plus grande que 1 mm à 2 mm, apparaissant sous forme de cristaux subidiomorphes, de grains grossiers à médiums, intercroissant avec la gangue silicatée (plagioclase, pyroxène, etc.) de la texture de cumulat. Les analyses à la microsonde électronique montrent que les grains d’ilménite sont minéralogiquement et chimiquement homogènes avec un faible contenu en V (moyenne 0.18% équiv. V2O5 ). Contrairement, les grains de magnétite titanifère sont hétérogènes, contenant des lamelles d’ilménite en "trellisworks"; ces grains sont pauvres en Ti et riches en V pour la portion magnétite de la magnétite titanifère [surtout contenant moins de 2 wt. % TiO2, et en moyenne 1.41% équiv. (1.16% V2O3) pour 20 analyses]. Ainsi, la magnétite est le principal minerai de vanadium; elle renferme du vanadium sous forme de V3+ et non de V5+, tel qu’il a été communément et à tort rapporté. Nous avons aussi défini un "flowchart" pour la bénéficiation des minerais de vanadium-titanium."

Jan 1, 1998

By Peter J. Franklin

"Short-term mine planning of open pits is an activity that has historically been carried out by hand. Typically, the use of computers has played little part in this type of mine planning. This paper describes the objectives and the procedures involved in short-term mine planning, comments on the type of computer systems available, and describes in detail a computer-aided short-term planning and scheduling system known as STEPS.IntroductionThe mine planning department of any o pen-pit mining operation performs a wide variety of different tasks. However, their primary concern is the preparation of detailed long-and short-term mine plans. These mine plan s will define the long-term operating strategies and definitive everyday working plan s for the ongoing development of the open pit.In this day and age, when operating costs have spiralled upwards due to inflation , and product revenues have decreased due to depressed economies and poor markets, it is vitally important for all aspects of the mining operation, including mine planning, to be efficient and cost effective.There are numerous options available for planning engineers when generating a mine plan. A cost effective mine plan must investigate all these options and select the optimum. When using manual planning techniques, it is often impossible to evaluate all the available options. To do this, and to produce an optimum mine plan, a computer is required.This paper discusses mine planning, with emphasis toward the short-term plan and comments on how the processes may be computerized. It also describes in detail, a computer software system called STEPS, which has been designed as an interactive graphics, computer-aided short -term mine planning and scheduling tool."

Jan 1, 1985

By C. V. Sibbald

"This paper provides a description of the Highmont copper-molybdenum concentrator from primary crushing through grinding, flotation, tailings disposal and water reclamation. The unique features of the operation will be emphasized.IntroductionThe Highmont property is located in the southern portion of the Highland Valley adjacent to and east of Lornex and about 4 miles south of Bethlehem Copper. The plantsite is at an elevation of 5100 ft.Highmont acquired the property in 1966 and in 1969 Teck Corporation entered into an exploration agreement which contained the option to finance the property to production . A detailed feasibility study of the project was completed in 1971. A positive production decision was deferred at that time because of the prevailing soft copper market and relatively low molybdenum price. The development of a strong molybdenum market in late 1978 and early 1979 led to a re-examination of project economics, and a decision to proceed to production was made in April 1979.The Highmont ore zones occur adjacent to and on either side of an east-west-trending quartz porphyry dyke. The two major zones , the east and west pits, contain 122 million tons of ore assaying 0.27070 Cu and 0.029% Mo. Chalcopyrite, bornite and molybdenite are the minerals of economic interest. Chalcopyrite is the predominant copper mineral. Mineralization occurs primarily along fractures and is zoned according to fracture density. Some pyrite is present, but for the most part it is outside the ore zone. Surface oxidation is shallow throughout the orebody.Wright Engineers Limited were responsible for the major part of the engineering design. Site construction, which began in the spring of 1979, is under the direction of Commonwealth Construction. The first concentrator line is scheduled for completion late in 1980, the other for early in 1981."

Jan 1, 1981

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners&apos; fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992

By G. Robert Guillet

"Ontario enjoys the advantage of its proximity to the large industrial market of northeastern North America. Together with Quebec and fifteen nearby U.S. states, an industrial base of more than half the total for both countries is provided by a population of 100 million.Mineral fillers such as barite, calcium carbonate, kaolin, mica, silica and talc are of major importance in the manufacture of paper, paint, plastics, rubber, vinyl tile, carpet backing, putty, caulks, sealants and adhesives. Ontario has all of these minerals, but domestic production falls short of demand in some cases, and mica and kaolin are not produced at all.This paper reviews the market and outlines the distribution of the major filler-consuming plants of northeastern North America. It also identifies the principal producers of filler minerals in the United States and Canada.IntroductionOf all the uses for industrial minerals, mineral fillers are probably the least understood. Originally used primarily to add low-cost bulk to a variety of commodities without seriously affecting their properties, filler minerals have become essential components that enhance and extend the properties of their hosts. Hence the term ""extender"" which, for all practical purposes, is synonymous with ""filler"". Today, fillers and extenders are not solely low-cost additives, but ingredients that provide essential characteristics to the products they fill.The major markets for mineral fillers are paint, paper, plastics, rubber, adhesives and floor coverings. But there are many others: putty, pesticides, wire and cable coatings, caulking and asphaltic compounds, oilcloth, wall-paper, joint cements, inks, sealants and many others. Barite, calcium carbonate, kaolin, mica, silica and talc are among the more important filler minerals discussed in this paper, but there are at least a dozen others. And the increasing practice of coating the mineral surfaces with certain coupling agents or metal stearates is constantly expanding the range of characteristics and hence the marketing opportunities.Whiteness, particle shape, fineness of grind and cost are the principal considerations in selecting a filler, but other characteristics such as weight, opacity, hardness and chemical inertness may be dominant considerations in specific applications."

Jan 1, 1987

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

By L. Mohammadi

Outline ?Background on the accident at the Sullivan Mine No.1 Waste Dump ?Holistic approach to understand the reason for accidents (Atmospheric) ?Specific hazards at reclamation sites ?Regular atmospheric risk assessment at reclamation sites ?Fuzzy risk assessment ?Managing risk at legacy sites

May 1, 2010

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By John Hughes

1. De Beers, Diamonds and Canada 1.1. De Beers was founded long ago (1888, the same time that Canada became a country) in a rural mining village in South Africa. Today, we employ 22,000 people across 19 countries and have 14 mines including open pits, shafts, beach-sands and seabed. 1.2. Last year our sales were US$5.7 billion and our total production amounted to 47 million carats which means a 40% global market share. For the Kyoto buffs in the audience, the company consumes 66 million cubic metres of water per annum, 210 million litres of hydrocarbon fuel and 1,600 GWh of electricity. Stats are good, but aren?t as expressive as a movie. This one is 2 minutes long, which is quicker than I could elaborate. (Video 1 - 2 minutes) 2. De Beers in Botswana is the leading source of diamonds 2.1 Today Botswana is the Jewell in the Crown. There are three big open pits that enjoy economies of scale that make them the lowest cost producers. Last year 60 million tonnes of overburden and 30 million tonnes of ore were moved in Botswana alone. Botswana produced 31 million carats, compared to 14 million carats in South Africa and 2 million very high quality carats inn Namibia. 3. Diamond Mines provide feedstock? ?.to jewellery stores

Apr 1, 2005