Search Documents

By Sylvain Picard

"RESUMELe gisement Silidor représente la dernière découverte effectuée dans le camp minier de Rouyn-noranda (fin 1985). Située à 5 km à I' ouest-nord-ouest de Rouyn-Noranda, ce gisement aurifère doit être mis en exploitation au cours du mois d’avril 1990. 11 est constitué par plusieurs facies minéralises comprenant une tonalité, un dyke mafique, une brèche carbonatée et par une veine de quartz. L’or se présente en particules très fines associées ou non à la pyrite. La zone d’altération hematitisee se développe sur une largeur de 30m environ de chaque cote de la veine. Une première étude structurale montre que la minéralisation s’est mise en place le long d’une zone de tension, orientée NNW, résultant de I' interaction de deux zones de cisaillement dextre orientées N270° et N300°. Les réserves diluées sont évaluées jusqu’ à 700 m de profondeur, à 4,78 Mt à 5,4 g/t Au. ABSTRACTThe Silidor ore deposit, located 5km WNW of Rouyn-Noranda, is the latest discovery made in the Rouyn-Noranda mining camp. Discovered at the end of 1985, this gold deposit will begin production in the spring of 1990. The deposit comprises several facies including a tonalite, a mafic dyke, a carbonated breccia and quartz vein. Gold is present as very fine grains, associated or not with pyrite. A 30m wide hematized alteration zone is developed on both sides of the structure. A structural analysis shows that the mineralization took place along a NNW oriented tension zone that resulted from the interaction of two dextral shear zones, oriented N270 and N300 respectively. The diluted ore reserves are estimated at4,78 Mt at 5,4 g/t down to a depth of 700m."

Jan 1, 1990

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter's Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all 'hot-metal' basis.

Jan 1, 1938

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By J. Mrozowski, R. Kurowski, A. Chmielarz, Z. Szolomicki

PbSO4 is a commonly encountered component of the materials used in lead recycling (e.g. battery paste) and in by-products of metallurgical processes (e.g. residues from zinc hydrometallurgy, dust from copper smelting). Smelting of battery paste results in SO2 emission and in generation of significant amounts of hazardous ‘white slag’. Those adverse phenomena can be eliminated by removal of sulphur from the paste. Lead-bearing by-product materials are of polymetallic character with usually low Pb content, which makes lead recovery technologically difficult and uneconomic. However it can be successfully achieved by extraction of lead sulphate from solid phase with triethylenetetramine (TETA) water solutions. That compound has capability for selective solvation of a whole lead sulphate molecule. Virtually pure lead carbonate can be precipitated by means of saturation of lead-loaded aqueous TETA solution with carbon dioxide, and complete regeneration of the extractant is achieved by fixing of sulphate ion into gypsum through operation of calcium hydroxide suspension. The paper presents results of the lab and pilot scale studies into process of battery paste desulphurisation and recovery of lead from the residue of zinc calcine leaching.

Jan 1, 2014

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By G. W. Smith

"The adsorption of dehydroabietylamine acetate on quartz, hematite, rutile and baddeleyite has been deter-mined for concentrations ranging from 0.3 to 5,600 µ. moles/I and for pH values ranging from 2.5 to 10.5.The surface tension, UV and IR spectra, equivalent conductance and ion concentrations for dehydroabiety lamine acetate solutions have been determined.Contact-angle and flotability studies have established that good collection may be obtained with this amine but that selectivity depends on the suitable use of depressants for some of the minerals."

Jan 1, 1971

Arsenic bearing minerals such as enargite (Cu3AsS4) and tennantite (Cu12As4S13), which may associate with major copper minerals such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and bomite (Cu2FeS4), usually report to the copper concentrate in conventional flotation due to their similar flotation properties. Arsenic in a copper concentrate causes environmental problems and also problems in the subsequent pyrometallurgical process. Voltammetric studies were carried out to investigate the oxidation characteristics of enargite, tennantite, chalcopyrite, chalcocite and bomite. Contact angle measurements and micro-flotation tests were conducted to examine the flotation characteristics of enargite and chalcopyrite under controlled pulp potentials. Selective flotation of enargite from chalcopyrite under varied pulp potentials was conducted to investigate the feasibility of arsenic removal from a copper concentrate. The test results indicate that the non-arsenic bearing copper minerals ( chalcopyrite, chalcocite and bornite) were easier to oxidise than arsenic bearing minerals ( enargite and tennantite) in an alkaline solution. Enargite floated well at a potential as high as +0.45 V vs. SCE while chalcopyrite was completely depressed at a potential higher than +0.43 V vs. SCE. Selective flotation revealed that enargite can be successfully removed from chalcopyrite through controlling the pulp potential at +0.30 ~ +0.50 V vs. SCE.

Jan 1, 2007

By S. E. Jackson, L. J. Cabri

Quantitative determination of gold at sub-ppm concentrations in sulphide minerals is an important component of deportment studies for sulphide-gold deposits. Laser Ablation Inductively Coupled Mass Spectrometry (LA-ICP-MS) analysis is preferred for this application because it rapidly and cost-effectively provides spatially resolved (<20 pm), low ppb concentration data for gold and other elements in mineral grains. Recent advances in LA-ICP-MS analysis include the development and application of elemental mapping. Raw signals from multiple line scans or lines-of-spots are deconvoluted and calibrated to generate elemental maps which provide detailed information on spatial variations of gold and other elements within and between grains.

Jan 1, 2011

By J. D. Bosman, L. J. Gardner

"The Bushveld Complex is a large layered igneous intrusion, located in the northern parts of the Republic of South Africa. The complex hosts the largest known reserves of Platinum Group Metals in the world. On the western limb of the complex, mining of the Merensky economic horizon and UG2 chromitite layer has been conducted for many years by several mining companies, including Impala Platinum Limited. Over the past decade, Impala has planned a new generation of greenfield vertical shafts, commencing with comprehensive geological and geotechnical studies. As part of the geotechnical studies, numerous tests have been conducted to quantify the mechanical properties of the various near-reef rock types. These tests include point load tests conducted in the field, as well as uni-axial compressive strength, triaxial compressive strength, and Brazilian disc tensile strength tests conducted in specialist laboratories. The authors have compiled an extensive database containing a large number of tests for different rock types, ranging from felsic Anorthosite to mafic Pegmatoid. The database was analysed to quantify the mechanical properties and values for Mohr Coulomb and Hoek Brown failure criteria for each rock type typically exposed by mining. The paper will provide a data set of rock mechanical properties typically used in numerical modelling and other design processes. Using the significant number of tests available, data describing the variability of the various parameters will be included."

Jan 1, 2015

By Matthew D. Meyer

SMART, an association of surface mining companies formed in 1995 to develop a coordinated approach to technology development for the mining industry, has recognized the need for the establishment of a worldwide database that continuously collects mining equipment data and provides metrics related to productivity and cost. Under the auspices of SMART, Syncrude Canada, Suncor Energy and Albian Sands Energy (three oil sands mining operations located in northern Alberta) have established a pilot project for mine benchmarking. This presentation will include a review of the pilot progress including: ???Data gathering techniques: means of collection and storage, proposed practice for data control and normalization, access to data/reports and format for data. ???Reports/analyses for individuals, across groups, within the total industry pool and publicly. ???Security and confidentiality of information belonging to identified parties. ???Sharing of best practices among members. SMART has identified two key deliverables to ensure success of the project. First, data supplied from surface mines must be validated and normalized to common definitions and then analyzed to provide participating companies with regular reports that allow them to understand their position and resultant opportunities to achieve world-class performance. This model maintains granularity of the data for each operation that can then be recombined into standard comparisons or specific indices as required. The general categories of: operating delays, maintenance downtime, standby, and scheduled downtime, have been used to frame comparisons. Second, participating companies are looking to go behind the indices to identify and share best practices that distinguish particular operations. The spirit of cooperation between the companies involved in the pilot project is meant to be a model for future expansion of the benchmarking project.

Apr 1, 2005

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

By B. I. Whittington

This paper examines the effect of cation type (i.e. NH4+, Na+ and K+) and anion type (i.e. SO42- and C1-) on the extraction of nickel during the pressure acid leaching of a Western Australian laterite ore. The results are compared with testwork conducted with other Western Australian nickel laterite ores and the possible process implications of adding an additive to a plant autoclave are considered. Addition of either (NH4)2SO4, Na2SO4 or K2SO4 increased both the nickel extraction and the acid consumption, provided that the level of additive was not too great. For example, the nickel extraction of 93% increased to above 96% in the presence of additives, but decreased to 94% when, for example, NH4 levels increased from 7 kg/t ore to 21 kg/t ore. The relative stability of the jarosite species formed when additives were present influenced the amount of jarosite in the residue and, hence, both the final free acidity and overall nickel extraction. The use of Cl- versus SO42- salts as additives had little effect on overall nickel extraction or overall free acid values, although the presence of SO42- additives appeared to enhance nickel extraction kinetics over the first 60 minutes of the reaction. In contrast, manganese extraction was enhanced by the presence of Cl- additives.

Jan 1, 2004

By W. Griffith

"While oxalic acid precipitation practices are commonly applied on purified rare earth elements (REEs) pregnant leaching solutions (PLS), few efforts have been reported using oxalic acid (OXA) to recover REEs directly from untreated PLS. High oxalic acid demand is the most significant issue in all these direct oxalic precipitation (DOP) practices. Preliminary research on DOP of REE from a dilute PLS originating from an acid bake followed by water leaching was conducted. At 75°C, the oxalic acid demand was between 12 and 18 times the stoichiometric requirement for complete REE precipitation. Conducting DOP at 25°C had superior REE recovery but the product purity and filterability declined. Between 75°C and 100°C, REE recovery increased with increasing temperature. When sodium hydroxide was used to adjust the pH during DOP, in the range of 0.5 to 1.5, higher pH benefited REE recovery. Using ammonium hydroxide in place of sodium hydroxide, the REE recovery was reduced by close to 5%. Sodium chloride addition to the PLS was also investigated and the results showed that at both 75°C and 25°C, the REE recovery was enhanced substantially. At 25°C, when the oxalic acid addition was controlled at 4.7 times the stoichiometric requirement, the overall REE recovery reached 95% with the addition of 240 g/L NaCl. Other reagents such as KCl, NH4Cl also showed significant enhanced REE recovery at the same oxalic acid addition. The addition of sodium sulphate appeared to largely enhance the precipitation of LREE but inhibited the formation of HREE oxalate. All results indicate the formation of rare earth double salts may play an important role in REE DOP sulphate media.INTRODUCTIONThe conventional routes for recovering rare earth elements (REEs) from a sulphuric acid pregnant leaching solution (PLS) involves an initial purification step for removal of iron, aluminium for example by precipitation through neutralization, followed by precipitation of REEs as hydroxide, oxalate or carbonate salts, or by bulk solvent extraction for REE recovery (Xia, 2013). Another route was used by Bayan Obo in their historical flowsheet, where the PLS was first subjected to double sulphate precipitation, then the remaining REEs, mostly heavy rare earth elements (HREE), were recovered by oxalate precipitation (Li, 2011)."

Jan 1, 2016

By Ross Gallinger

In 1997 a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded (i) that Canadian industry and NRCan should fund a small secretariat in Ottawa to support technology transfer in Canada and (ii) that it was important for industry to continue the momentum of MEND on an international scale. The need for INAP (International Network for Acid Prevention) was strongly endorsed by company, university, consultant and government experts from Australia, Canada and the U.S. who were convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP&apos;s members to promote the dissemination of successful practices, the identification of knowledge gaps and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry based initiative to globally coordinate research and development in the management of sulfide mine waste. Significant improvements in the management of sulfidic mine materials through knowledge sharing, research and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP.

May 1, 2002

By \/eena Sahajwalla, Jonathan Dicker, Paul O'Kane, Cath Skidmore, James Dankwah, Magdalena Zaharia, Rita Khanna, David Knights, N Saha-Chaudhury, Somyote Kongkarat

Due to the inherent limitations of current methods of disposal of end of life polymeric materials, avenues are researched towards developing alternative, environmentally friendly and economic recycling processes. Different polymeric materials (i.e. rubber, high density polyethylene (HDPE) and polyethylene therephtalate (PET)), quite distinct in terms of chemical structure and composition, were considered in the present study as carbon resources in EAF steelmaking. Investigations were conducted in both laboratory and industrial scale steelmaking to assess the effectiveness of using these materials as carbon sources for slag foaming in EAF steelmaking. Slag foaming is important because it enhances furnace efficiency.

Jan 1, 2011

By Leslie S. Weldon

THE Lake Shore mine has been developed by two vertical shafts, with level intervals at 200 feet to the 2200 level and at 125 feet below this horizon. A main cross-cut joins the two shafts on all levels to the bottom of No. 3 shaft, and opening into these cross-cuts are the ore passes and sand passes, which are completed from surface To the 4450 level. In the west part of the mine, additional connections have been made between No. 1 and No. 2 veins, through which the major part of the ore from No. 2 vein west is routed to drifts in No. 1 vein. With the lesser amount of stoping on No. 1 vein, this arrangement permits better haulage to be maintained. The ore passes are driven at 50 degrees from the ends of short cross-cuts off the main ones and are broken through to the levels above at the mouths of the short cross-cuts, to allow for dumping on each level. The passes are controlled at each level by ball-and-chain gates and deliver to crushers and thence to loading pockets, shown in Figure 1. That system is quite flexible in that it is possible to by-pass the crushers at any station and load from either shaft at a number of different pockets. The sand passes are driven from the main cross-cuts at the same inclination as, and parallel to, the ore passes. Each is equipped with a chute and dump hole, so that waste or sand fill may be loaded or dumped at each level. A transfer door, hinged on the bottom, is installed opposite the chute for by-passing fill from one level to the next, and in the closed position protects the opening at the top of the pass. The dump hole situated beside the transfer door is protected by a grizzly with 10-inch spaces. Waste rock may be withdrawn from the system through No. 3 shaft loading pocket at the 2950 level to a waste bin on surface. Levels are developed by drifts in No. 1 and No. 2 veins for their entire lengths. Subsidiary breaks are followed at a later date, when full information has been obtained by exploration, and a considerable amount of development by sub-drifts is carried out in the upper part of the mine, particularly in more or less erratic sections of No. 1 vein.

Jan 1, 1936

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By Donka H. Andreeva

Gold catalysts based on different supports, titania, zirconia, ceria and mesoporous titania and zirconia, nonpromoted and promoted by vanadia in the reaction of complete benzene oxidation have been studied. XRD, HRTEM, TPR, Raman and ESR spectroscopy were applied for the characterization of the catalysts. The influence of gold on the reduction behavior, state and structure of vanadia on the surface was studied, as well as the role of supports nature on the properties and catalytic activity. A strong synergistic effect between gold and vanadia was observed for the all studied catalysts with an exception of the catalysts supported on mesoporous zirconia. In the last case the catalysts containing gold and gold-vanadia exhibit high and equal catalytic activity. The catalysts on ceria show highest and stable catalytic activity in the studied reaction among the all studied catalysts.

Oct 1, 2003