Search Documents

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By A. R. Hekmat

Hypereutectic Al-Si alloys are used in applications that require high resistance to wear and corrosion, hardness and low coefficient of thermal expansion, To maximize the properties of these alloys, semi-solid processing can be utilized to modify the solidification structure of the primary silicon crystals as well as to reduce microsegregation and porosity, The transformation and spheroidization of primary Si crystals by shearing in the semi-solid state are not fully understood as they precipitate in the presence of other alloy phases, The objective of the present work is the determination the rheological characteristics of A390 (Al-17%Si-4,5%Cu-0.5%Mg) alloy using a Couette type (Haake RV12) viscometer and examining the microstructural evolution during continuous cooling and isothermal shear rate experiments, The effect of shear rate, solid fraction (temperature) and morphological evolution of the silicon crystals are investigated.

Jan 1, 2005

By L. P. Chrismas

"IN 1975, Nova Scotia produced 1.8 million tons of coal with a FOB mine value of $47.6 million. Of this total, about 30 per cent or 600,000 tons was coking coal and the remainder was steam and industrial-grade coal. The Nova Scotia Power Corporation consumed 630,000 tons in three generating stations and 570,000 tons were sold to Sydney Steel for making coke for its steel operations. Exports, principally to Great Britain, comprised 370,000 tons in 1975 in addition to the 300,- 000 tons shipped to other provinces for use by cement and pulp and paper companies. In 1975, just over 100,000 tons of coking coal were imported into the province from Alberta. Before 1975, low-volatile coking coal was traditionally obtained from the United States. In 1975, production came from seven individual mines and one project involving reclamation from mine dumps in Pictou County. Of the seven producers, four are owned by the Cape Breton Development Corporation, a federal Crown corporation; the remaining three are small independent mines, but, even though small, they are sizeable contributors to the economies of their local areas. After 101 years of continuous operation, Devco's Princess mine was closed in 1975. The Nova Scotia coal industry, in terms of value, accounted for about half of total mineral production in 1975. The industry provides jobs for 3,000 men and women. It is also significant that in 1975 Nova Scotia produced about 6.5 per cent of Canada's total coal production of 28.3 million tons. Detailed statistics on Nova Scotia's coal industry appear in the Appendix."

Jan 1, 1976

By Jarrett. K. M.

Nobody has, as yet, made a perfect machine. Therefore, when a machine is operating and functioning as it is designed to do, there is always some vibration present. This is easily and simply measurable with present-day equipment and any increase in the amount of vibration will indicate a potential failure. When an increase is noted, vibration analysis can pinpoint the cause of the potential failure and remedial action can be taken before an unscheduled shutdown is necessary or a breakdown occurs.

Jan 1, 1972

By Raj Rajamani

In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal?s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned. First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized.

Jan 1, 2012

By G. A. Fenton, A. Vervoort, M. Alvarez Grima

"High-risk underwater mining operations necessitate characterizing spatial heterogeneity and resource uncertainty. Local average subdivision is a method of simulating spatial deposit variability inside a cell through a sequence of discretization stages, during which a cell is further subdivided into four or eight cells. New developments are presented to validate simulated deposit models and deal with point measurements of geotechnical and ore-grade properties. This paper illustrates the relevance of translating spatial deposit variability into financial or operational performance indicators during underwater resource exploitation. Two synthetic case studies highlight the challenges of underwater mining in relation to production plans and equipment selection.RÉSUMÉ Les opérations d’extraction minière subaquatique à risque élevé exigent une caractérisation de l’hétérogénéité spatiale et de l’incertitude de la ressource. La moyenne locale de subdivision est une méthode de simuler la variabilité spatiale du gisement dans une cellule par une séquence d’étapes de discrétisation durant lesquelles une cellule est subdivisée en quatre ou huit cellules. De nouveaux développements sont présentés afin de valider les modèles de simulation des gisements et de traiter des mesures ponctuelles des propriétés géotechniques et de teneur du minerai. Le présent article illustre la pertinence de traduire la variabilité spatiale du gisement en indicateurs de rendement financier ou opérationnel durant l’exploitation subaquatique de la ressource. Deux cas synthétiques soulignent les défis de l’exploitation minière subaquatique par rapport aux plans de production et de choix des équipements."

Jan 1, 2015

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By K. Yamaguchi

"This Precious metals content copper scrap is treated with a copper smelting process, and copper and precious metals are recovered. The precious metal lost in the slag is increasing with increasing of treated scrap amount. To determine the portion of the precious metals chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. The distribution of precious metals between copper matte and FeOx-SiO2 slag phases is determined at 1300 oC and a fixed partial pressure of SO2 of 0.1 atm for the matte grades from 40 to 70 mass% of copper. The distribution ratios show a tendency to increase when the grade of matte is increased. In addition, the solubility of platinum and rhodium in the FeOx-SiO2-CaO slag under the air and the solubility of platinum in the FeOx-SiO2 slag equilibrated with a pure platinum or the Pt-Cu alloy were determined at 1300oC in the range of oxygen partial pressure from 10-9 to 10-7. The solubility of platinum and rhodium in the slag tends to increase with increasing content of copper in the slag and oxygen partial pressure. INTRODUCTIONThe stringency of the supply and demand of platinum group metal (PGM) intensifies by localization for resources and increase of the demand for PGM, furthermore, smelting and the recycling of PGM in the nonferrous smelting process take an important role. Scrap containing a precious metal for the purpose of collection of PGM is treated by copper smelting recently. With increase of the treatment amounts, loss of PGM in slags is the serious problem.In considering of PGM loss in slags, knowledge of the distribution behavior for PGM between slag and matte phases or slag and copper phases and the PGM solubility in slags is important. The distribution ratios of silver and gold between the FeOx-SiO2 slag and the Fe-Cu matte were reported by Roghani (Roghani et al., 2000), Shinha (Shinha et al., 1985) and Takeda (Takeda et al., 1993) However, there is no data for the PGM distribution ratio. On the other hand, the PGM solubility in slags was reported by Sano (Sano et al., 1997) However, there is very few report for the solubility of PGM in the nonferrous smelting slags."

Jan 1, 2012

By J. I. Carroll, J. A. Walker

"Abstract - Camelback is a small (=200 000 tonnes), moderate grade (5%-7% Zn+Pb), volcanogenic massive sulfide deposit, which occurs within the Nepisiguit Falls Formation of the Ordovician Tetagouche Group. The host rocks are tuffaceous sedimentary rocks (Little Falls member) that overlie quartz-feldspar porphyritic tufflavas (Grand Falls member). The hanging-wall sequence comprises rhyolite of the Flat Landing Brook Formation, overlain by the Forty Mile Brook tholeiitic basalt. A dike of unaltered andesite was intersected beneath the massive sulfides, but was not found in the hanging-wall sequence in the vicinity of the deposit. The stratiform part of the deposit is made up of two, steeply south dipping, subparallel massive lenses that average approximately 4 m in thickness. Each lens is zoned, with an upper part consisting mainly of a pyrite and a basal part containing pyrite, sphalerite, and galena, with Ag values. The Au content in the massive sulfides is low (average = 52 ppb for 271 samples), but tends to be enriched in the massive pyrite near the top of each lens. Oxide facies iron formation is spatially associated with the massive sulfides, and has been traced up to 1800 m along strike. Footwall hydrothermal alteration is typical of VMS systems, and is characterized by depletion in K2O and Na2O, and enrichment in MgO and Fe2O3T with proximity to massive sulfides. The massive lenses are underlain by intensely chloritic, fine-grained, tuffaceous sedimentary rocks containing locally significant sulfide (chalcopyrite > pyrite > pyrrhotite) veins, which are interpreted to represent feeder zone mineralization. Unlike many VMS deposits, there is no evidence of silicification beneath the massive sulfides at the top of the feeder zone. The oxygen isotopic compositions (d18O = -1.5‰ to -0.3‰) of hydrothermal chlorite coupled with sulfur isotopic compositions (d34S ˜ 12‰) of the massive sulfides suggest that seawater was the dominant fluid in the hydrothermal system. Normalized rare earth element diagrams show flat Ce profiles and positive Eu anomalies, indicating that modified seawater was involved in ore formation; i.e., high-temperature (=350ºC), acidic, and reduced prior to entrainment into the hydrothermal cell. Although, seawater was the dominant fluid in the sulfide-forming system, d34S values of stringer zone sulfides (8.5‰) coupled with elevated Sn (400 ppm) in one massive sulfide sample indicate that there was at least some magmatic component in the hydrothermal cell."

Jan 1, 2006

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By P. -A. Bosse, J. Robitaille, P. Blatter

The LaRonde ore is a Cu-Zn-Pb ore with gold (3-4 g/t) and silver (60-100 g/t). The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation. Subsequent to a recent mill expansion, excessive gold was reporting to zinc concentrate with a concurrent decrease in gold to copper concentrate. Owing to the higher return obtained from the metal, the mill endeavors to recover additional gold and silver to the copper concentrate and minimize the placement of precious metals to the zinc concentrate. A gold deportment study showed that the gold occurs mainly as küstelite, with a moderate amount of electrum and a minor amount of native gold. It also showed that various sulfur-based Au-and/or Ag-bearing coatings on liberated küstelite and electrum were the major mineralogical factors that caused gold and silver to report to zinc concentrate. By frequency, such coatings were observed on 70-80% of total liberated gold particles reporting to the zinc concentrate. Based on the gold deportment and the chemistry of the coatings, the collector chemistry was reviewed and a new collector was added into the circuit which resulted in a significant increase in gold and silver recovery to the copper concentrate. The information obtained from the mineralogy confirmed and guided other process optimization. In this paper, the authors will describe the process mineralogy of the LaRonde ores, and in particular, the mineralogical evidence diagnosing the problem. Reference will also be made to the rationale behind how the problem was solved, the results achieved, and future steps in optimization.

Jan 1, 2005

By S. R. Stopic

The EU-financed INTREAT Project (Integrated treatment of industrial wastes to¬wards prevention of regional water resources contamination) addresses the environmental pollution associated with solid and liquid wastes/effluents produced by complex sulphide ore mining and metallurgical activities. The results concerning the electrolytic recovery of cop¬per from effluents formed after mixing of streams from Copper Refining, Precious Metals Plant and Electrolyte Regeneration in the Balkan Area will be shown. The waste water is characterized by low pH values and high contents of heavy metals, such as Cu, Ni, Bi, As, Sb. The majority of these waste water flow untreated into the natural water streams and through the network of existing rivers, which end up in the river Danube. The influence of current density and flow rate on the deposition rate, the quality of copper and the process efficiency will be presented. The full continuous process is based on cells with rotating disc cathodes and represents a pre-treatment step before common neutralisation in a cascade line

Jan 1, 2007

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By J. J. Jonas

The categories of interpass time encountered in hot rolling are characterized. These are shown to fall into three broad categories: short (in rod rolling); intermediate (in strip processing); and long (in plate schedules). The effects of interpass time on recrystallization and carbonitride precipitation are described, and particularly on the interaction between these two mechanisms. The interactions, in turn, determine the final microstructure produced as well as the mechanical properties.

Jan 1, 2005

By R. A. Ford

The paper outlines: methods used for the determination of wear metals in motor and transmission oils; contaminents in motor, transmission and crusher lubricating oils; and viscosity determinations. Case histories and costs are presented to illustrate the value of an oil analysis program. Introduction NORANDA MINES LIMITED (BELL COPPER DIVISION) is located on the shores of Babine Lake, approximately 450 miles north of Vancouver, British Columbia. Access to the mine is by road from Topley, B.C., about 40 miles away. When a preventive maintenance analysis program was first considered, it was obvious that if samples were to be sent out for analysis, results would not be available for at least a week, due to the distance from any commercial laboratory. The assay laboratory was asked to investigate the possibility of determining wear metals on site. A limited program was started soon after production commenced, and this has now grown to include all large mobile equipment as well as crushers and grinding mills. The laboratory also now determines viscosity, fuel dilution, dirt and abrasives, glycol and water. All these results are ready within two days. This paper will outline the methods used, data interpretation, several case histories and the benefits from such a program.

Jan 1, 1977

By A. V. Tarasov

There are still a number of copper smelters in the world using the roasting and smelting process flow diagram for treating sulphide raw materials. The technical, economic and environmental performance indicators of such operations are inferior to the respective indicators of advanced processes. First of all with respect to copper and sulphur recovery: 95% and 75% as compared with 98% and over 90%, respectively. Based on the studies of the single-stage smelting process to produce white metal and blister copper conducted during recent years an analysis of the feasibility of roastingsmelting technology improvement was carried out in the Gintsvetmet Institute to substantially increase the copper and sulphur recoveries. On the basis of this analysis, it was proposed to modernize the technology and equipment within the framework of the existing process flow-sheet. The proposed modernization implies an increase in the roasting temperature; higher desulphurization degree in the process of roasting; a number of modifications in the roaster design depending on the particular conditions of a given operation; addition of lime flux to the feed charge to roasting; and transition to combined calcium-silicate smelting slags. The metallurgical and energy computations made have indicated that the proposed modifications of the technology will improve the copper and sulphur recovery up to 98% and 90%, respectively. The required capital investments have been estimated using as an example a particular copper smelter, the payback period determined taking into consideration additional output, fuel saving and a reduction in fines for sulphur emissions. For comparison, the capital cost of a smelter modernization is given for change-over to basically new autogenous Ausmelt, Outokumpu and V anyukov smelting technologies.

Jan 1, 2007

The Millennium deposit, located in northern Saskatchewan between the McArthur River mine and the Key Lake mill, has considerable potential for becoming an operating mine. Located in the Athabasca Basin, Millennium is blessed with both the riches and the challenges that this basin offers. The potential for ground water inflows during shaft sinking, and the unconventional challenges associated with underground uranium mining, render the successful development of a new mine in this area especially rewarding. The preliminary design and engineering of the Millennium Project has tapped into the experience of other operations in the area, and has utilized new applications of geophysics technology to enhance the understanding of the local geological structure. This discussion will focus on the innovations, and the challenges specific to uranium mining, for a deposit that is poised to be one of the next mines to supplement Saskatchewan's uranium resources.

May 1, 2008

By W. P. Campbell

In the course of the development of the Red Coulee field, northwest of Coutts, Alberta, a considerable amount of information has been gathered by the Department of the Interior regarding the chemical character of waters encountered in the drilling of wells in this area. The writer, in this paper, has undertaken to assemble the available material with the idea of deducing what relations, if any, may exist between the different waters from the same well, and also how these compare with waters encountered in similar horizons in other wells. From no other district, with which the Department of the Interior has had to do, have there been received so many samples of water, and yet not all the waters logged in the drilling reports were sent in for analysis. The information, therefore, herein contained is not as complete as the writer would have desired, but sufficient evidence has been accumulated to indicate some very definite tendencies in the chemical nature of the waters of this field. The drilling of Red Coulee wells has been carried out exclusively by percussive tools. These permit 'dry' drilling, and, consequently, water-sands are recognized when encountered. Had rotary tools been used, information regarding water-sands would have been very meagre, if not entirely lacking, since, in the mudding-off process, water-sands would have been overlooked, with the result that, should water break through into a completed well, its source would not be known and remedial efforts would be greatly handicapped, if not entirely defeated.

Jan 1, 1931

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005