Search Documents

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

By Paul Armstrong

THE first discovery of lead and zinc ore on Calumet island was made in 1893 by John Lawn, who then staked a portion of the property now owned by Calumet Mines, Limited. His discovery was developed by James and Calvin Russell, who are said to have shipped a few tons of sorted ore, averaging 39 per cent zinc, 13 per cent lead, and 11 oz. silver per ton. In 1898, the property was being operated by the Grand Calumet Mining Company, who mined and shipped, for treatment in a Belgian smelter, 1,100 tons of ore averaging 32 per cent zinc, 9 per cent lead, and an unreported content of gold and silver. After some indecisive exploration by an American syndicate in 1907, the property lay idle until1910, when the Calumet Metals Company-later reorganized as the Calumet Zinc and Lead Company-re-commenced exploration. After sinking an 85-foot shaft-the McDonald shaft-and doing a few hundred feet of drifting and cross-cutting, this Company, in 1912, erected a 150-ton daily capacity gravity-concentration plant, in which some 800 tons of ore, mined from the McDonald shaft and Bowie pit, were milled. Owing to very disappointing mill recoveries, the property was shut clown and-after several years of idleness-in? 1916 the mill and mining plant were destroyed by fire and the Company went into bankruptcy. In 1918, an unknown operator shipped to an Omaha, Nebraska, smelter 22 tons of ore, probably sorted from the dumps of the Ste. Anne shaft and Galena pits, averaging 44 percent lead, and 0.26 oz. gold and 61 oz. silver per ton. The British Metals Corporation (Canada), Limited, in 1926, optioned the property. They unwatered the McDonald shaft and, after doing an additional 300 feet of cross-cutting and drifting on the 85-ft. level, estimated there were some 33,000 tons of ore between this level and the surface. Surface exploration, including trenching, on other showings on the property gave discouraging results and the option was dropped.

Jan 1, 1941

By Mario Morin

The application of underground pre-concentration technology to narrow vein mining has the potential to change the entire economics of bulk mining methods when used in narrow vein situations. The rejection of waste at or near the face means that a higher-grade ore can be sent to surface. The waste rock can be reused directly as backfill. Swelling of the muck through blasting means that only 60 to 65% can be used as fill. Planning and scheduling of the fill usage is key to the success of this method. Through the use of simulation and system analysis, this paper examines the planning and scheduling implications of underground pre-concentration when applied to traditional narrow vein mining methods (cut-and-fill /drift-and-fill, longhole, AVOCA). It considers the logistical factors that represent potential system bottlenecks that are key to understanding the correct implementation and control strategies.

Oct 1, 2004

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

By Jan E. Nesset

It is just over 100 years since the practice of blowing small bubbles into a mixture of ground ore and water revolutionized the mining industry, resulting in uneconomic deposits becoming highlyprofitable mines, along with the inevitable lawsuits over this new technology called froth flotation. To this day, the viability of many mining projects rests largely with the ability of flotation to effectively capture the valuable minerals and reject wastes. Remarkably, bubble behaviour in flotation has not been well understood until very recently with the advent of new sensor technologies that can be brought directly into the operating plants. This presentation will review the importance to the mining industry of understanding bubbles, highlight these new technologies and illustrate, with examples, how paying attention to your bubbles will pay off.

Jan 1, 2009

By Š. Šachlová, T. Lokajícek, M. Petružálek, T. Svitek, A. Štastná

During the past 20 years, alkali silicate reaction (ASR) as a cause of concrete deterioration has been studied by a wide range of experimental methods such as microstructural and macrostructural analysis, bulk chemical analysis, X-ray and neutron diffraction analysis, etc. All of these data are compared with expansion values of mortar bars (following ASTM standard C 1260). Recent studies indicate the useful application of non-destructive methods with the aim of better reflecting mechanical properties and the degree of deterioration of real concrete. Ultrasonic testing methods (including ultrasonic pulse velocity UPV) are widely used to determine material mechanical properties and the changes induced by a variety of mechanical or chemical processes. However, only a few laboratory studies of ASR focused on ultrasonic testing of mortar bars. Due to this fact, a heating chamber was designed and constructed to enable ultrasonic sounding of mortar bar specimens while stored in accelerating solution. Regular ultrasonic sounding of mortar bars reveals significant dependence of ultrasonic data such as longitudinal P-wave velocity, signal energy, signal amplitude and signal frequency on mortar bar storage time. Ultrasonic data were subjected to time domain as well as frequency domain analysis. Different storage conditions were used to determine the effect of ASR on ultrasonic parameters. Mortar bars, prepared in the same manner with one type of aggregate, were stored in cold or warm water or in an accelerating warm medium. Ultrasonic data accurately reflects the differences in hardening and deterioration of tested mortar bars due to different storage conditions. Ultrasonic results showed very good correlation with the results of ASTM standard expansion tests and much higher sensitivity to ASR-induced concrete deterioration. Expansion tests showed 1% measured length differences in comparison with up to 80% resolution of ultrasonic data. The ultrasonic testing proved to be a suitable laboratory method for investigating ASR-related processes and could lead to an improvement of standard testing procedures.

Jan 1, 2015

By Ian Bruce

Tailings and water management facilities are essential and integral components of mine and mill operations. They must be managed for the long term in order to ensure that safe and environmentally responsible stewardship is achieved. Toward this end, in 1998, The Mining Association of Canada (MAC) published A Guide to the Management of Tailings Facilities, which recommended the implementation of a tailings management framework (Figure 1) to integrate environmental and safety considerations into each stage of the life cycle of a tailings facility, from initial site selection and design, through construction and operation, to eventual decommissioning and closure. By February 2000 it was becoming apparent that while mining companies were making significant progress toward implementing and documenting tailings management systems, and integrating them with overall environmental management systems, further effort was warranted in their application at the operational level. In particular, a need was identified for further guidance in preparing manuals that outline procedures for the safe operation, maintenance and surveillance (OMS) of tailings and water management facilities.

May 1, 2002

By P. D. R. Maltby

"1. INTRODUCTIONMy talk today will discuss a new development in the thickening of slurries and clarification of waste water - the Enviro-Clear thickener. Several industrial installations of the thickener have been made in North America in the following applications:1.,water clarification in sugar beet processing plants.2.,separation of pregnant liquors from solid wastes following acid leaching in uranium mills3.,clarification of waste water from coal treatment plants as described in a paper in the June 1975 transactions of the SME entitled ""Application and Utilization of the Enviro Clear Thickener in a U.S. Steel Coal Preparation Plant"" by A.A. Terchnik, D.T. King and J.S. Anderson.2. HISTORYThe application of the Enviro-Clear thickener can be traced back to the filing of U.S. Patent 3523889 in 1970 by the inventor F. Eis. The claims of this patent are shown in Slide 1.The new concept was developed for sugar beet processing by the Spreckels Division of Amstar Corporation, and several such thickeners have subsequently been installed in various sugar beet plants. The Enviro-Clear Co. or New York took over the world-wide manufacturing and marketing of the thickener. Experience in the sugar beet industry indicated that the Enviro-Clear thickener volume requirements could be reduced to as low as one tenth that of a conventional type thickener. Various coal samples were supplied by U.S. Steel Research Laboratories for testing. The tests indicated that feed rate loadings of 3 gpm/ft.2 could be obtained by the Enviro-Clear thickener. Such results led to several industrial applications in the coal industry. Subsequently other branches of the mineral processing industry have come to learn of the possibilities of using this thickener. Slide 2 shows a list of commercial Enviro-Clear installations at the end of 1975."

Jan 1, 1976

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

By D. W. Euler, D. G. Brophey

"In an attempt to address the issue of rising labour costs, and to improve productivity, a laser-based system to guide underground LHDs and trucks has been developed. This comprehensive system is known as the Opti-Trak system.Essentially, the vehicle is equipped with front and rear-mounted lasers which scan a reference strip mounted on the drift back. The vehicle follows this reference strip and in addition, based on reflective bar codes mounted beside the reference strip, initiates certain functions (i.e. dump cycle, speed change, brake check, etc.). Any programming that is drift-specific is handled by the positioning of the reference strips and bar codes. Consequently, the vehicle can easily travel to many different haulageways or branches, providing the reference strip and bar codes are in place.The advantages of this system are an immediate elimination of haulage operator costs and an increase in available hauling time to 7 hours out of an 8-hour shift as compared to the typical 5Y2 out of 8 hours that a manned haulage system offers.This paper describes the Opti-Trak system and the benefits to be realized from automation of mine haulage requirements."

Jan 1, 1994

By W. K. Gummer

"THE LOCATION of Canada's present aluminum industry is determined by availability of hydroelectric power, and ready access to ocean transport facilities. The chief raw material for the production of the metal is imported by ship over several thousand miles of water. In times of freedom of shipping and uncontested movement this provides the industry with its cheapest method of operation. However, during the early part of the last decade the general conditions of ocean and rail transportation were such that interest in the treatment of materials other than bauxite was greatly stimulated. This was the case not only in Canada, of course, but in most other countries.Canada has no deposits of bauxite and much research was carried out on other aluminous materials, chiefly silicates, in an effort to develop more or less economic and feasible methods of treatment. In the United States, this research was considerably more extensive. Some projects were early shown to be of little or no value, whereas others, including the widely publicized lime-sinter and soda-lime-sinter methods, became important. In North America, however, apart from the application of the sinter method to the hitherto waste-product (red mud) of the normal Bayer plant operation, none of these processes contributed appreciably to the production of aluminum during the war. In certain European countries, on the other hand, largely because of their situation with regard to bauxite deposits, they had a more general application, and Germany, for example, produced alumina from clay, ashes, and slag by at least four methods."

Jan 1, 1952

By A. N. Veltmeyer

"INTRODUCTIONTeck-Corona Operating Corporation's David Bell Mine is located 35 Km east of Marathon, Ontario. In conjunction with its 1000 tonne per day gold concentrator, the company operates an effluent treatment plant for the treatment of mill, mine and site effluents prior to environmental discharge. This paper provides a brief overview of treatment strategies and methods, employed to detoxify final effluent.WATER MANAGEMENTThe tailings impoundment basin, located 3 Km south of the plant site, provides storage capacity for all process effluents and site run-off. Basin supernatant (reclaim water) is recirculated to the plant for reuse as process water, in order to minimize fresh water consumption. As site run-off and limited fresh water intake exceed natural losses due to evaporation, reclaim water in excess of process requirements is passed through the effluent treatment (ET) facility to control tailings basin level by providing regulated discharge of environmentally acceptable effluent. (Figure 1)PASSIVE TREATMENTTo reduce treatment costs and burden on the ET facility, reclaim water is fed to the plant to take maximum advantage of natural destruction processes occurring in the tailings basin.These include: volatilizationphotodecompositionbiological oxidation and precipitationstorm water dilutionConcentrator recovery techniques (Figure 2) are directed toward maximizing gold recovery while limiting the addition and extraction of contaminants requiring disposal and eventual treatment.Currently ore ground to 90% -200 mesh is pre-aerated at pH 9.0 with lime for 18 hours prior to 30 hours cyanidation at pH 9.5 with low cyanide ion excess (70 ppm).Pre-aeration passivates cyanicides prior to cyanide contact. This reduces cyanide consumption and the formation of cyanide complexes. In conjunction with recovery requirements low pH is maintained to retard the dissolution of stibnite into its antimony and sulfide components."

Jan 1, 1989

By Michel Aubertin

Les digues de retenue de résidus miniers devraient être conçues de façon à supporter les charges les plus défavorables qui puissent être anticipées. Les nombreux incidents survenus au cours des dernières années à travers le monde montrent toutefois que la stabilité de ces ouvrages reste encore problématique. Les cas de rupture les plus courants sont reliés aux glissements le long des pentes, à la liquéfaction des rejets, au débordement des bassins, ainsi qu?à l'érosion régressive et de surface. Après avoir rappelé la nature et l?importance des certains incidents récents, l?origine de ces problèmes est brièvement présentée. On aborde ensuite le lien entre les critères à adopter pour la conception des ouvrages et les risques associés à leur rupture. De nouvelles avenues pour aider à contrôler certains problèmes sont enfin discutées, en mettant l?emphase sur la codisposition des roches stériles dans le parc à résidus miniers.

Nov 1, 2002

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By Bruno Bussière

Le drainage minier acide (DMA) provenant de la circulation des eaux à travers les rejets miniers sulfureux est sans doute le principal problème environnemental auquel est confrontée l?industrie minière. Afin de prévenir les problèmes environnementaux reliés au DMA, on doit restreindre la présence de l?une et/ou de l?autre des principales composantes menant à la production d?acide, soit l?eau, l?air et les sulfures. Pour ce faire, différentes techniques ont été proposées au cours des dernières années, dont la désulfuration environnementale et les couvertures avec effets de barrière capillaire (CEBC). Dans ce papier, on propose d?utiliser ces deux techniques en combinaison. Ainsi, on produirait un rejet désulfuré à l?usine de traitement qui pourrait, par la suite, être utilisé comme matériau pour la couche de rétention d?eau de la CEBC. Dans un premier temps, on présente les résultats d?une étude de laboratoire qui montre qu?il est possible de désulfurer les rejets de concentrateur à l?aide de la flottation non sélective jusqu?à l?obtention d?un résidu non générateur d?acide. Par la suite, des essais en colonne ont permis de démontrer qu?il est possible de limiter la production de DMA d?un résidu sulfureux à l?aide d?une CEBC dont la couche fine est constituée de résidus désulfurés. Des prédictions théoriques estiment même que la présence de sulfures résiduels dans la fraction désulfurée utilisée comme matériau pour la rétention d?eau peut avoir un effet bénéfique en réduisant la migration d?oxygène. En effet, les sulfures contenus dans la couche de rétention d?eau peuvent consommer l?oxygène qui tente de migrer vers le bas et, ainsi, réduire les flux d?oxygène qui atteignent les rejets réactifs.

Nov 1, 2002

By Robert S. MacPhail, Chilombo Henry, Arnold Kabamba, David Mukelebai, Suresh Thirunagari, Bukali Victor, Yoram Kapai, Chomba Leonard, Kanna Amarasingham

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate. Developed by Charles Tennant & Co (Canada) Ltd and has shown improved collection properties over SIPX for sulphide minerals flotation. Improvement of recoveries, grades, faster kinetics, lower dosages, high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31. Recent plant trial carried out in the copper circuit at one of the largest copper mine in Zambia shown over US $ 2.00 Million annual improvement on the bottom line over SIPX at current copper prices. Data produced also showed superior grade and recoveries from rougher concentrates that previously had not been attainable with other reagents effectively. Flex 31 has also shown positive outcomes with zinc, Copper/Zinc, arsenopyrite and copper/molybdenum ores.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthate, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by the research division of Charles Tennant & Company (Canada) Limited has produced a chemically enhanced SIPX. This product has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The product was named “FLEX 31”."

Jan 1, 2016

By M. J. Slater

Ion exchange using resins is one of the few processes capable of reducing ionic contaminants in effluents to very low levels. Continuous fluidized-bed ion exchange is an advantageous technique for processing dirty effluents and thin slurries. It also reduces resin inventory and equipment cost compared to fixed packed beds. A simple continuous fluidized-bed unit has been investigated for treating effluents and its performance is described. Breakthrough curves were first obtained from static fluidized fixed beds; these data were then used to determine the required operating conditions for a periodic-flow, countercurrent fluidized-bed ion exchange system. A waste stream, containing about 56 ppm copper, was treated in the continuous system using an extraction fluidized bed depth of 203 cm and a flow rate of 1.22 cm3/ cm2s (900 gph / sq.ft) to yield an effluent containing less than 0.02 ppm copper. A generalized design method is proposed for similar chemical systems.

Jan 1, 1978