Search Documents

By J Carswell, K McTyer

The Pajingo gold operation in Queensland is approximately 50 kilometres south of Charters Towers and 134km south-west of Townsville. The resource was discovered in 1983 and first open pit gold production began in 1986. The mine traditionally employed a bottom-up sequence – a combination of modified and traditional Avoca methods with run-of-mine waste backfill. This practice caused many high-grade crown pillars to be left in place, yet accessible. In recent years, these crown pillars have been extracted by injection grouting of rockfill. This process facilitated blind up-hole open stoping. To date, thirteen separate injection campaigns have been completed, of which ten were deemed successful. In general, the two key technical difficulties in this mining technique are: maintaining a consistent high-quality ground consolidation of the rock fill material; and controlling the drill and blast practices during stoping. Here, effective drill-and-blast control was found to be essential to achieve the dual aims of 100% extraction, and maximum sill pillar stability to minimise dilution. During stoping, the technical performance of the consolidated rock-fill was recorded; both to verify the design, and to identify operational improvements. The results showed that Pajingo has realised both reduced production down-time through use of early strength gain grout, and more rapid and thorough grout consolidation through changes to the emplacement method. The optimisation of consolidated rock fill has led to several quantifiable benefits to the mine, including: profitable extraction of previously sterilised crown pillars resulting in both increased ore reserves and production profile; improvements to the stability of grouted stope crowns, thereby reducing safety and production related; risks associated with open up-hole stopes; reduction in cost and time constraints, with respect to the grouting of loose fill; and reduction in grout curing time – from 14 days to 8 days – thereby minimising production down-time. This paper is a case study of the evolution and optimisation of the up-hole open stoping mining method at Pajingo. The challenges and successes are discussed in terms of their key mining outcomes. CITATION:McTyer, K and Carswell, J, 2018. Evolution of rock fill consolidation at Pajingo Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 66–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Dunham

For decades we’ve been focusing on reconciliation as a tool to validate mineral resource estimates. And for decades we’ve been misleading ourselves. The concept of reconciliation is simple. Predict, measure, compare and assess the quality of the prediction. This four-step process reflects the ideas of statistical process control and the plan-do-check-act cycle of Shewhart and Deming fame and our intuitive understanding of using system feedback to improve performance. In an ideal world where data is robust and dense this type of feedback loop can be useful. In the mining industry however, there are some fundamental flaws with the conceptual framework. At almost every stage of the process from pre-estimation through to final production the mining system is plagued by material challenges with data and measurement quality and quantity, system delays, and losses from a supposedly closed system. These issues can and do impact on the benefits sought from reconciliation. Instead of providing feedback leading to improved estimation, reconciliation can result in poor decisions, distracting investigations, and exacerbate the noise in an already noisy system. Before we can rely on reconciliation as a management tool, we need to address the multiple challenges present in our everyday practices. Some of the most critical issues are addressed in this paper.

May 24, 2023

By M Dean, M Nehring, P Knights, M S. Kizil

Integrated continuous mining techniques such as fully mobile in-pit crusher and conveyor (FMIPCC) systems offer inherent labour, energy and environmental benefits to deep pit metalliferous mines. However, before such systems become commonplace, a number of barriers must be overcome.This paper outlines a number of commonly perceived barriers to FMIPCC application, together with a number of suggested solutions. The paper advances a design approach for specifying FMIPCC systems for deep pit metalliferous applications. A novel FMIPCC configuration is advanced using a hydraulic excavator in backhoe configuration. Because of the requirement to minimise belt extensions, a mine planning approach is presented based on a series of parallel and radial belt conveyor moves.The FMIPCC system does not fully replace truck-shovel systems. In the proposed mine plan, sinking is undertaken with truck-shovel systems using a series of box cuts, whereas pit ‘widening’ activities are accomplished via the FMIPCC system. Because of inherent differences in mine sequencing, the net present value derived from the FMIPCC mine will differ markedly from that derived from traditional, nested-pit, truck-shovel mining approaches. Therefore, any comparison of the FMIPCC and truck-shovel approaches must take into account radically different mine planning approaches.CITATION:Dean, M, Knights, P, Kizil, M S and Nehring, M, 2015. Selection and planning of fully mobile in-pit crusher and conveyor systems for deep open pit metalliferous applications, in Proceedings Third International Future Mining Conference, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By V Rasouli, G Cavanough, A Mokaramian

The sampling time, the costs and its quality are the three factors that determine the best method of drilling in mineral exploration. The two principal methods of reverse circulation (RC) and diamond core drilling are often used in combination by mine operators. RC is used for drilling shallow holes and in-pit grade control, and core drilling for deeper holes to identify future resources. The RC method is faster and more flexible than coring and provides virtually uncontaminated cuttings (ranges from dust to 25 mm chips) to the surface cyclone suitable for geochemical anomalies. The diamond coring produces core samples to increase the level of geological knowledge and the 3D extension and distribution of the orebody. However, both of these methods are subjected to certain limitations and inefficiencies in reaching deeper depths and drilling complex hole geometries. Examples of such shortcomings include the inability to provide enough air pressure for RC drilling and high friction between drill pipe and the hole wall in diamond core drilling.Considering that delivering large volume of reliable samples from deep zones to the surface in shortest possible time is of paramount importance in mineral exploration, and assuming that obtaining core samples over whole overburden is not always essential, then drilling small size holes as fast as possible and delivering the small chip samples to the surface would be a good alternative with several advantages over conventional drilling methods for deep hard rocks mineral exploration. As a result, the use of coiled tube (CT) drilling technology has been proposed recently for such applications. CT is a continuous length of ductile steel or composite tube stored and transported on a large reel; and allows fast drilling by eliminating the connection time and providing continuous circulation during drilling. This enables quick access to the zone of interest to collect the cuttings or obtain core samples. CT is advantageous particularly in drilling directional boreholes and multi-laterals. In this paper, feasibility of using CT delivering reliable samples is discussed for deep mineral exploration. In addition, recent developments and practices are presented that make CT a reliable drilling technology to drill cheaper, faster and deeper and to deliver more continuous and reliable data and samples from deep formations.CITATION:Mokaramian, A, Rasouli, V and Cavanough, G, 2012. Quality sampling using coiled tubing drilling in deep mineral exploration, in Proceedings Sampling 2012 , pp 73-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By N J Welham

A commercial enargite concentrate was mechanically milled in inert and oxidising atmospheres for 10 hours. No substantial effect was observed in either an inert atmosphere or in air other than a broadening and weakening of the diffraction peaks. Milling dry in oxygen or wet in air was dramatic with a significant reaction occurring which formed arsenolite, As2O3 and CuSO4.5H2O, both of which are readily soluble.A small amount of SO2 was also formed. Dissolution in acid left CuS as the major phase implying incomplete oxidation. The small fraction of tennantite in the sample was comparatively resistant to oxidation.

Jan 1, 2001

By R Shaw

There are many small to medium carbonate hosted complex zinc containing deposits where the zinc is not economically recoverable either as concentrate or metal. High grade (>20% Zn) run of mine ore can be processed but even this material gives relatively poor returns. Considerable effort has gone into developing new technology for either upgrading the ore and/or recovering zinc metal hydrometallurgically but there has been limited success. Minetometal has developed a process capable of economically treating these deposits to give marketable lead and zinc products. This paper reviews alternative processes for these ores and gives a detailed description of the Minetometal Process. CITATION: Shaw, R, 2018. Processing carbonate hosted zinc-lead ores, in Proceedings Complex Orebodies Conference 2018, pp 130–131 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Cochrane

Time and time again history shows us that mine closures are sustainability failures. Mine operators do not know how to turn the mine closure into an asset and communities around the mine do not know how to plan or what to implement to be sustainable when the mine needs to close. If we want to achieve sustainability when we close a mine, we generally need to consider what economic activity we will have to create leading up to the mine closure to ensure that the communities remaining in the area are not worse off after mining than before. There is not one silver bullet solution to mine closure, as all mines are affected by different environmental and socio-economic conditions. That is one of the reasons why mine closure is so difficult.Effective stakeholder engagement is the nucleus around which sustainability is built. Achieving sustainability as part of mine closure means not only a self-sufficient community, but also could lead to transformation of that asset.A key issue is that neighbouring communities become completely reliant on the mine. The mine has influenced the economic, environmental and social aspects of the community and with no alternative economic sources. The community and municipality will struggle with capacity to maintain infrastructure, services and jobs. This not only impacts the mine workers and their families but also other businesses and people in the town that make a living by servicing the needs of the workers and their families. Social problems associated with a mining operations and closures need to be considered. The misuse of alcohol, domestic violence, breakdown in law and order, economic and health issues all have a severe influence. Families often need to relocate from the mining town to find work. This further perpetuates the impact of the mine closure to the economic viability of the town. CITATION:Cochrane, K, 2018. Is your mine closure a sustainability failure? Transform your asset and create a self supporting neighbouring community. It’s as easy as ABCD!, in Proceedings Life-of-Mine 2018, pp 38–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By P Oikkonen

Sprayed concrete has played an integral role in underground rock support for nearly a century. However, concrete is also considered to be one of the biggest environmental problems in construction and mining, largely because of the high carbon footprint of cement and aggregates production. This is driving the industry to find ways to cut concrete usage where possible. Improving sustainability by cutting concrete material consumption also reduces application time and costs. Improving concrete properties can make it possible to design thinner linings, but as awareness of safety and longer design lifetimes are driving developments in the opposite direction, it is not realistic to see this as a major factor in cutting concrete consumption. More accessible solutions are focusing on layer thickness control and minimising rebound and wastage. Digital technology and innovation offer excellent tools for improving sustainability while optimising other aspects of the spraying process at the same time. A digital layer thickness control system gives near-real-time information to the sprayer operator with full coverage of the sprayed surface. This enables the operator to achieve consistent layer thickness on the first pass, in comparison to the traditional methods of overspraying with the aim of achieving sufficient layer thickness, probe drilling after the concrete has set, and respraying at a later stage if needed. Operator competence is the single biggest variable in a successful sprayed concrete process, affecting rebound and wastage levels. Unfortunately, the learning curve to become a master sprayer is quite steep and training on a real sprayer and real concrete requires a significant amount of time and money. Training in a virtual reality (VR) environment enables operator training to be carried out in a low-risk environment and provides a way of measuring performance and assessing and certifying the operators. After the VR training period, a novice nozzle operator has the basic understanding to start working on a real sprayer, and an experienced nozzle operator can benefit from the possibility of assessing their performance.

Mar 29, 2023

By D A. Sims

This paper outlines the contributing factors to a series of erroneous Mineral Resource estimates which led to considerable loss, including significant reduction of mine life and consequently a large write-down of asset value. The error prompted divestment of the mineral asset in the short-term by the owners, a major mining company. There were multiple and complex contributions to the result: • The mine was undergoing a transition in the deposit geology with increasing depth that was not accommodated in the models. Early indications of the geological transition in initial drilling were generally unrecognised in resource modelling. The shortcomings of the models became apparent with increasing infill drilling and subsequent production reconciliation. • There was a lack of recognition of, and confidence in, site-based input and skills by corporate technical management. The site had a reputation internally for over-delivery to plan early in its life and that supported the anticipation of ongoing metal delivery into the mine plan by management. • A corporate lack of confidence in site being able to adequately domain the mineralisation led to the use of a CIK domaining process, rather than one which was geologically based. This domaining process led to gross over-statement of mineralisation trends reflected in the subsequent OK estimate. • Timelines on the outsourced estimation process were so short that validation was not possible. Obvious errors in the estimate versus data were not able to be used to correct the issues and the site’s Competent Person sign-off occurred without adequate checks. This case study is presented to reinforce the concept that Mineral Resource estimates are not solely based on the ability of the Competent Person to satisfactorily guide the process. There are usually multiple complex issues in the estimation process which need to be recognised and considered in judging reconciliations of model to actual.

May 24, 2023

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By M Jones

Legacy tailings storage facilities exist within operating mine sites across Australia. These tailings storage facilities are often viewed as rehabilitation liabilities but with considered assessment may prove to be a resource. Extraction of such a resource might add value to operations by providing cash flow during the development of new mines; providing supplementary mill feed for existing mines undergoing step changes in operations; and supporting mine closure activities. Hellyer Gold Mines is successfully extracting and reprocessing sub-aqueous material from legacy tailings storage facilities at their Hellyer operation in north-west Tasmania. The Hellyer tailings storage facilities contain poly-metallic material from the Hellyer and Fossey underground deposits dating back to the 1980s as well as material from tailings reprocessing activities by other operators of the Hellyer site. Hellyer Gold Mines is reclaiming sub-aqueous material using cutter-suction dredgers and reprocessing on-site. Hellyer is the only operation of its type in Australia and few such operations exist worldwide. Key learnings around the estimation of a resource for legacy tailings storage facilities have been acquired at Hellyer that can be applied to the assessment of other tailings storage facilities. The application of dredging as a mining method at Hellyer is delivered through collaboration with experts from outside the mining industry under the direction of a mining engineer. Key elements required for the planning and delivery of safe and efficient dredging inside tailings storage facilities have been identified at Hellyer and are presented to provide a road map to the development of other dredging operations.

Sep 1, 2024

By G R. Hancock, J F. Martín Duque

Post-mining landscapes are required to geomorphologically and ecologically integrate with their surrounds (Martín Duque et al., 2015). Designing and constructing an erosionally stable landform is the first and arguably most important part of the rehabilitation process. Without an erosionally stable landform topsoil and nutrients are lost, shallow groundwater is depleted as well as when excessive erosion occurs, expose suboptimal materials. Here we examine the ideas of geomorphic design and rehabilitation and how the landform can be tested and enhanced using computer based design and landscape evolution models. Specifically we evaluate the complementary capabilities of landscape modelling (SIBERIA) (Hancock and Willgoose, 2017) and geomorphic design software (Natural Regrade with GeoFluv) (Bugosh et al., 2016), in order to maximise erosional stability on post-mining landscapes (Zapico et al., 2018). CITATION:Hancock, G R and Martín Duque, J F, 2018. Geomorphic design and landscape evolution modelling for best practice mine rehabilitation, in Proceedings Life-of-Mine 2018, pp 119–121 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By O Dominguez

Significant value can be added to ore supplied from the mine to the mill by measuring its quality in real time and performing grade control additional to that within the mine. Responsibility for ore quality between the mine and mill stockpiles is not always clear due to operational siloes so geologists and mining engineers need to be involved collaboratively with metallurgists to optimise ore value prior to processing. Sensors, such as the GEOSCAN-M which utilises high specification Prompt Gamma Neutron Activation Analysis (PGNAA), that measure conveyed ore flow representatively (continuous and fully penetrative) and in real time have been used in the minerals sector since 2003 and have been successfully applied in multiple commodities. Quality can be measured within the mine where material is conveyed underground or in-pit. Bulk ore sorting is used to divert increments of waste from the ore stream to upgrade material sent to the crushed ore stockpile (COS) as well as to create run-of-mine (ROM) stockpiles of different qualities to maximise blending opportunities and accommodate processing priorities, eg blending out deleterious content. The real time composition measurement can be combined with moisture and fragmentation analysis data for improved ore type characterisation, to control ore blending, for feedback to the mining schedule and block model reconciliation, and feed forward control for grinding and processing operations. The paper discusses various parameters measured and derived in existing operations that are used to maximise coarse waste rejection and metal recovery, optimise plant feed quality consistency, and reduce consumables; power, grinding media, water, reagents, and minimise fine tailings generation. Innovative geometallurgy applications are also discussed.

Mar 22, 2022

By S Farrokhpay, C Akop

Copper-gold-pyrite ore types with an elevated pyrite head grade utilise a sequential flotation circuit to recover initially a copper-gold concentrate with a pyrite-gold concentrate being produced from the tailing of the initial circuit.A simpler flotation circuit with lower operating and capital costs for treatment of such copper-gold-pyrite ores with an elevated pyrite head assay was sought in the described work. After characterising the ore, the objective was to apply bulk rougher flotation of both the copper minerals and pyrite for the copper-gold-pyrite ore at natural pH. Hence, no lime or other pyrite depressants were required in bulk roughing. The bulk rougher concentrate was upgraded in a cleaner circuit to reject non-sulfide gangue and then the resulting sulfide concentrate was separated by depressing the pyrite to produce two products (copper and pyrite concentrates, both having significant gold assays). A standard test with a sequential circuit was applied to the same ore for comparison.The chalcopyrite and pyrite losses in the tailing from the rougher circuit were the same for both bulk and sequential roughing (less than six per cent). In cleaning (bulk circuit), the effective pH for pyrite depression was 11.8–11.9; copper recovery was 70–75 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 80–85 per cent (grade of 34–36 per cent sulfur).These results approached those for the sequential circuit where copper recovery was 80–85 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 83 per cent (grade of 38 per cent sulfur).The observed effects of feed sizing on the liberation of minerals in the rougher feed are discussed. Options for improving the bulk circuit results are also considered. Importantly, the implications of various aspects of these findings for the bulk circuit are discussed with an industrial focus.CITATION:Akop, C, Farrokhpay, S and Johnson, N W, 2014. An alternative circuit for chalcopyrite-pyrite ores with elevated pyrite content in Cu-Au ore treatment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 407–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By C K. McKenzie

As more and more mining operations around the world either switch to, or trial, electronic initiation systems, the breadth of knowledge and experience regarding their effective application has widened considerably.In South America, for example, there is a strong perception that in order to achieve the finest possible fragmentation, very short electronic delays must be used between successive holes within a row. Limited field studies involving measurement of fragmentation have been conducted to support that paradigm and there are few long term studies which have been strongly supported by measurements of productivity either in the pit, in the plant, or in the leaching pads.On the other hand, some well documented studies have been conducted in North America, showing not only the impact of delay timing on fragmentation but also the effect on semi-autogenous grinding (SAG) mill productivity over extended periods of in excess of 12 months. To date, those studies suggest that optimum timing is considerably longer than the times commonly used in South America.This paper explores the current knowledge of the effects of delay timing on issues ranging from size distribution to vibration impacts in pit walls, to vibration and overpressure impacts in surrounding communities. It also explores how fragmentation modelling can be adapted to reflect fragmentation trends that have been reported in various technical conferences around the world.

Nov 8, 2011

During the first five years of operation, the Lihir gold mine has steadily increased plant throughput rate to over 4 Mtpa, well above the original design capacity of 2.8 Mtpa. Understanding how future variations in ore type impact on plant performance has been an integral part of LihirÆs development program. This paper discusses the key drivers for significant improvements to the plant, including a second oxygen plant, a pilot flotation plant, an autoclave heat recovery circuit, a pebble crushing circuit and additional autoclave feed pumping capacity. The result is a process plant with the flexibility to accommodate variations in ore type without significant loss of throughput.

Jan 1, 2003

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J P. van Dyk

A new crude ilmenite beneficiation process was recently proposed that allowed for the preparation of a smelter grade ilmenite from ilmenite with elevated chromium content. Magnetising roasting was not utilised in the process. As part of this circuit an ilmenite low susceptible reject stream was produced that had a low magnetic susceptibility. In this article a magnetising roasting process was investigated to beneficiate this material. Tests were conducted on material produced by pilot scale simulations on a typical South African East Coast heavy mineral reserve. The results obtained were compared to those published in literature for crude ilmenite. The small-scale experiments were used to define approximate operational limits for the oxidising roasting of a low susceptible ilmenite low susceptible reject stream, although industrial roasting conditions may differ significantly from those obtained in laboratory units. In a next phase these results will be confirmed on pilot plant scale.

Jan 1, 2001

By T Stambolie

Mine planning processes are continuously evolving, increasing in complexity, and are required to be developed in shorter timeframes, often missing important steps in the process. Underground coal mines are also moving into more challenging environments, with the more favourable resources having been exhausted. In addition to traditional mine planning processes there is an increasing level of complexities associated with parallel systems including the preparation of Joint Ore Reserves Committee (JORC) compliant estimates (JORC, 2012 and Guidelines Review Committee, 2014) or seeking critical regulatory development consent to undertake mining. There is a clear link between geotechnical considerations and success of mining operations, and therefore it is essential that such considerations are elevated in both status and priority. It is obvious that geotechnical considerations are paramount in any mine, however it is imperative to accept that such considerations, and the collection of information relating to such, are undertaken from the onset of any mining project. CITATION:Stambolie, T, 2018. Elevating geotechnical considerations in the Australian underground coal industry and mine planning process, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 383–391 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018