Search Documents

By K Saito, M Hasegawa

Removing sulfur and phosphorus from molten iron can be expressed by the following reactions, respectively. [S]Fe + (O2-)slag = (S2-)slag + [O]Fe [P]Fe + (3/2) (O2-)slag + (5/2) (FeO)slag = (PO43-)slag + (5/2) Fe(liquid) These equations indicate that desulfurisation and dephosphorisation have opposite oxygen potential conditions. If a small amount of desulfurisation slag not removed is carried over to dephosphorisation process, the reaction of sulfur mentioned above proceeds toward left hand resulting in increasing sulfur content in molten iron. For better understanding of such re-sulfurisation reaction in hot metal pre-treatments, the present study aimed at evaluating the effect of iron oxide on the sulfur distribution ratio between slag and hot metal. To measure sulfide capacities and FeO activities simultaneously at temperatures below the melting point of pure iron, CaO-SiO2-FeO and CaO-Al2O3-FeO ternary molten slags were brought into equilibria with copper-iron-sulfur liquid alloys, and the equilibrium oxygen partial pressures were determined with an electrochemical technique involving the stabilised zirconia solid electrolyte. The experimental results showed that the sulfide capacity increased with an increase in FeO content, and this trend was consistent with the fact that FeO was basic. Although the addition of FeO raised the FeO activity and oxygen potential, the calculated value for sulfur distribution ratio between slag and hot metal increased with increasing FeO content.

Jun 19, 2024

To secure a sustainable competitive advantage some smelters may need strategies based on flexibility in feed and product ranges depending on immediate future projections of profitability. This paper explores the technical requirements for strategic diversity in smelting, leaving procurement, marketing and contractual considerations aside. The days when a smelting operation is tied specifically to say only processing zinc concentrates are perhaps drawing to a close. While internationally traded mineral concentrates are available, attractive business opportunities must exist for fully diversified custom smelters. Certain new and emerging technologies have inherent characteristics that are evaluated in this context. The paper identifies the basic building blocks that will permit such a scenario and assesses the technical feasibility. The ability to respond flexibly to environmental pressures is highlighted as being of paramount importance.

Jan 1, 1996

One of the problems with mining projects is the setting of the design criteria that will best match the requirements. Normally this is expressed in economic terms but can be other factors. With massive orebodies these problems are often compounded by the general lack of distinct mining boundaries. A technique using evaluation surfaces was developed at Palabora for the underground mine design. This technique has subsequently been applied on several other mining projects to assist in the determination of the design criteria. This paper discusses the method, illustrated by some of the results of these studies.

Jan 1, 2000

By Hill J. R M, McDonald M. M

A prediction technique for support perfor- mance of hydraulic backfill in narrow stopes is applied to two stopes separated vertically by a sill pillar. Predicted stope wall closures and fill pressures compare favorably with field measurements taken over a period of several years at two mines in the Coeur d'Alene dis- trict. Stope wall closure and peak pillar stress can be substantially reduced by improved fill quality within a practicable range of fill and rock properties.

Jan 1, 1973

By R Castroviejo, F Segundo, C Brea, J-C Catalina, H-J Bernhardt

Optical microscopy is a basic but still indispensable tool for examining mineral parageneses in ores. The design and concepts behind the reflected light ore microscope have obviously not been subject to spectacular technical evolutions in the last decades. However, digital imaging capabilities have opened new and stimulating perspectives for automated mineral identification. Recent works in developing multispectral image analysis (Pirard, 2004) have demonstrated its superior potential with respect to conventional colour imaging, but at the same time reconciliation with spectroscopic databases such as the Quantitative Data File III (Criddle and Stanley, 1993) still needs a more in-depth investigation as well as the possibility to extend both imaging and spectroscopy into the near infrared domain. In this paper, the authors present results gained from multispectral imaging in the range between 400 and 1000 nm together with spectrophotometric data from the QDFIII database, with an emphasis on minerals that cannot be easily distinguished in the visible spectrum.

Jan 1, 2008

FOR some years past it has been usual to specify high-grade copper for use for many purposes, but the practice of specifying zinc of a high degree of purity for certain purposes is of comparatively recent origin. It is a practice, however, which is extending ag the effect of the impurities in zinc on products manufactured therefrom becomes widely recognized.The notes hereunder are intended to briefly survey the principal uses to which high-gr.ade zinc is being put, and, wherever possible, to indicate the effect of the impurities normally present in the lower grades of zinc.In the United States zinc is graded into five divisions, known respectively as "High-grade" "Intermediate" "Brass Special" "Selected," and "Prime Western." The maximum amounts of impurities allowed in the various grades are indicated in Table I,which is compiled from data published by the American Society of Testing Materials:In addition, it is specified in an cases that the slabs shall be reasonably free from surface corrosion or adhering foreign matter. Although zinc used in Europe has in many cases been sold on analysis it is only recently that any attempt has been made to grade...

Jan 1, 1923

Kambalda Nickel Mines (KNM) currently have eight operating underground mines, three on care and maintenance and other orebodies at various stages of development. Each operation differs greatly in scale, ore grade, milling characteristics and cost structure. The optimum number of mines operating at any one time and their level of production, within the constraints of mill blending requirements and overall mill capacity, is the key to maximising profit in a climate of fluctuating nickel price. Cost models are developed for each mining operation which relate ore tonnes mined to total cost per pound of nickel produced from that mine. Aggregating the mine cost models provides a composite cost model for the entire operation. The cost models provide the operating levels necessary for each of the mines and hence Kambalda as a whole, to operate at the lowest cost per pound of nickel produced. However, lowest operating cost does not necessarily lead to maximum profit. The level of nickel price above operating cost can dictate maximum profit positions which are contrary to the lowest cost position. In addition, the decision to temporarily shutdown mines or reopen mines in response to nickel price movements comes at a cost. In considering the optimum operating position, the price of production capacity flexibility needs to be taken into account. This paper describes the process used to assess all these factors in arriving at the optimum operating position for Kambalda Nickel Mines for varying nickel prices. The same methodology can be used by corporate management in managing multiple mine sites as well as mine management managing multiple orebodies or stoping blocks for maximum profit.

Jan 1, 1995

The most appropriate technology needs to be applied to premining geological investigations to achieve reliable data for predictions of geological conditions ahead of mining. The paper describes the application of various investigatory techniques in BHP's Illawarra Collieries which are used to provide reliable assessments of structure, the nature of the coal and surrounding strata,, and the fluids contained in the strata. The techniques used include surface seismic, in-seam seismic, borehole drilling, electromagnetic and aeromagnetic surveys, hydrogeological investigations and in-mine mapping. The results of various case studies are presented as examples of the application of techniques.

Jan 1, 1988

By Hossaini SMF

After reviewing the various approach es,namely, empirical,analytical.observational and numerical, a logical systematic approach is proposed for the estimation of compressive strength of coal pillars. In this approach first,uniaxial compressive strength of coal in pillars is estimated,taking into account the size effect and the effect of discontinuities. Next,the compressive strength of coal pillars is estimated by determining the stress distribution in the pillar and the Bieniawski strength criterion. The results appear to be compatible to the ones obtained by Wilson's method. The traditional pillar design equations give improper answers for deep workings.

Jan 1, 1991

By Bourke J. H, Ashcroft T. B

Many changes have occurred in the world market for manganese over the last five years. Among these, the emergence of divided steel processes for the hot metal refining of pig iron is affecting the use of both ferruginous manganese ore and ferro manganese, at this stage particularly in the Japanese steel industry. Subsequent demand for higher quality manganese materials is promoting the use of thermally beneficiated products such as sinter. In addition, many processes are being developed for the direct smelting of fine manganese ores, of which plasma technology is the most advanced. Cost pressures and product quality requirements are encouraging pre- viously self sufficient countries such as The People's Republic of China and the USSR to import high grade manganese ores to supplement indigenous lower quality supplies. At the same time, Brazil has been provided with the impetus to convert its substantial reserves of ore to value added products.

Jan 1, 1988

By A G. Grice

Surface disposal of mining processing wastes is usually perceived as an undesirable consequence of meeting societyÆs needs for metals and minerals. Environmental disasters associated with the discharge or storage of such wastes, though infrequent, can have very damaging consequences for the environment and the industry. Reducing or eliminating the potential for such events may be achieved by placing some or all of these processing wastes back into the voids created by the mining operations. Processing operations may limit or enhance the opportunities for using tailings and other waste products as a backfill material. Backfilling is a truly multi-disciplinary process and requires the informed involvement of mining, metallurgical, engineering and environmental specialists. This paper describes the range of fill types currently being used in Australian mines, particularly those utilising processing wastes as constituents. It focuses on how processing operations can affect the suitability of these materials for the various types of fill, the resulting fill properties, fill performance and costs.

Jan 1, 2002

The Vera Nancy orebodies, although simple in overall geometry, are in detail generally narrow, multi-veined and fluctuating in width, strike and dip. Tight geological control is required to optimise gold and silver production from this bench stoping operation. The processes used to model the resource and to control ore drive development have evolved since mining commenced in 1997. Grade control is a combination of orebody sampling, geological data collection, understanding orebody geometry and the optimisation of ore driving and stoping activities. Global resource modelling utilises mainly drill hole data which is largely superceded by drive development data as stope development progresses. The orebody has a relatively low nugget effect that assists in grade estimation. Rather than rely on sophisticated grade interpolation methods, resource estimation to-date has focussed on developing the geological understanding of the orebody to ensure the framework for estimation is correct. Drill data alone is not adequate to define deposit geometry for stoping . Drive data is used as the dominant data set for stope geology modelling once development for a stope is complete.

Jan 1, 2000

By T Laurencont

The Queensland Department of Natural Resources and Mines (NR&M) accepted the environmental liability for the Mount Morgan minesite in 1991. This gold and copper mine located 38 km southwest of Rockhampton had been in operation for more than 100 years. Mining leases are still active while the feasibility of a reprocessing operation is carried out. From 1993, NR&M have operated a seepage interception pumpback system which has reduced the chronic load of acid rock drainage (ARD) to the adjacent Dee River, a tributary of the Fitzroy River system. In early-2000, it was recognised that a ten-year plan for rehabilitation of the mine, along with significant funding would be required if a long-term sustainable rehabilitation strategy was to be implemented at this minesite, ultimately making the seepage interception system redundant. A rehabilitation planning workshop coordinated by NR&M was held in May 2000. This workshop brought to the mine a range of technical expertise and key stakeholder groups. This workshop provided a technical forum for review of studies undertaken and to identify priority projects, which needed to be undertaken in the future to more clearly define contaminant sources on the mine site and to prioritise the rehabilitation program. Stakeholder consultation enabled the project team to be clear on community and other government (eg Environmental Protection Agency) expectations. It is clear that the future of the economically depressed community of Mount Morgan will be reliant on the careful management of the significant heritage values at the minesite for tourism, education and research. In the first year (2000), priority studies were initiated, which included whole of site studies on water balance, contaminant sources and a review of occupational health and safety and environment of the minesite and conservation and heritage scoping. Baseline vegetation and soil materials surveys were also initiated. The outcomes of these studies helped to shape the work program for the following year, while providing a basis for an additional funding application, which was granted. The second year of studies focused on building upon the existing baseline studies completed. In addition, studies focussed on addressing the priority issue of contingency planning for overflow from the open cut pit in accordance with best practice management of release water and river monitoring strategies were completed. Completion of these projects over the next six months will enable the optimal rehabilitation strategy to be defined in 2003. This optimal strategy may require the use of a water treatment plant for part of the ten-year program to provide space in the open cut pit for the deposition of ARD contaminant sources (eg waste dumps, tailings). It is envisaged that some sources will be rehabilitated insitu while others will be relocated to the open cut pit. Implementation of this strategy will be dependent on subsequent funding.

Jan 1, 2003

Gold mine production in South America was 247.3 tonnes in 1995 up from 156.4 tonnes ten years earlier in 1986. This represents a 58 per cent increase and amounted to 11 per cent of total world gold mine production. The major countries involved in order of production, were: Brazil (67.4 tonnes), Peru (51.5 tonnes),. Chile (48.5 tonnes), Colombia (24.1 tonnes), Venezuela (17.1 tonnes), Bolivia (16.0 tonnes), Ecuador (9.6 tonnes), Guyana (8.8 tonnes), French Guiana (3.3 tonnes) and Argentina (one tonne). The most dramatic increase was reported in Peru where production increased from 10.9 tonnes in 1986 to 51.5 tonnes in 1995, heavily influenced by the production from Minera Yanacocha which began operations in 1993 and produced 17.2 tonnes in 1995.With the reformation of the mining laws and the introduction of investment incentives in all the South American countries in recent years, dozens of major and junior mining companies began flocking into the area in the early-1990s to conduct exploration. A recent study undertaken in Brazil shows that an average of $240 million per year will be expended in this country during the period 1993 - 2010. Twenty-five per cent of this expenditure is expected to be made on gold exploration. Similar figures for Peru are $220 million total per year with 50 per cent for gold; $170 million per year in Argentina with 25 per cent for gold and $120 million ner year in Chile also with 25 Der cent for gold.

Jan 1, 1997

I am honoured and very pleased to have been given the opportunity this evening to say a few words of thanks not only on behalf of all the guests but especially for the delegates and accompanying persons attending the 13th Congress of the Council of Mining and Metallurgical Institutions. Firstly, I would like to congratulate Sir Hamilton Whyte,KCMG for his most interesting address. In his far ranging talk, when he showed knowledge of widely diverse subjects, I had a brief fear that he was going to be talking about the details of support methods in deep level mines, or how to avoid flotation problems in multi-metal mines. Although he did not go that far, he touched on subjects which have arisen this week - long term planning and secure supply of minerals at acceptable prices. The dire predictions of the Club of Rome have been debunked with a far more elastic supply of minerals having been proved. Combined with the importance of a falling birthrate in some parts of the world, this will lead to many changes in the future, when hopefully governments will take the long term view rather than look at the next budget or the next election. Maybe some of them are not too lazy to do this for all of us. However as a fellow Ukranian, I feel that he might have been called something different if he had been in Australia. Sir Hamilton, thank you for your talk. Once upon a time - and this is not a fairy story - there was a cobbler who had two sons; one very bright who became a professor of mathematics; the other, dim, who became a millionaire shoemaker. Asked for the secret of his success, the millionaire attributed it to a vital piece of economics which his father had imparted, "Be content with small margins on a large turnover." "So", said the millionaire, "I make my shoes for $2 a pair and sell them for $5. I am very happy with the three per cent profit."

Jan 1, 1986

By Prosser AP

The large body of knowledge about the relation between chemical process efficiency and mineralogical features is of only limited use. The profession ought to try to improve the methods of using information as well as adding to the knowledge. One attempt isòdescribed. Correlations between process efficiency factors and the mineralogical features of low- grade concentrates have been developed from both a theoretical analysis and experimental measurements. The ultimate recovery of a reactive phase in an inert matrix can be calcu- lated from simple measurements of the particle size, porosity and pore size of the concentrate, and the grain size of the reactive mineral., The rate of recovery, up to 98% recovery, can be calculated from simple measurements of particle size, porosity, proportion of reactive mineral and tortuosity. Some details are given. The correlations are of potential use in process selection and preliminary design. Satisfactory predictions have been made for near-ideal systems. Improvements in the measurement of pore size and tests on more realistic materials are required. The ultimate benefit of the correlations will be determined by the magnitude and frequency of the effects of mineralogical features other than those specified above.

Jan 1, 1975

IT is very difficult for a founder engaged in jobbing work, comprising all sizes and classes of castings, to appreciate that the analysis of the iron he is using cannot entirely fill the situation he desires for his varied classes of work. Neither is there any panacea in the shape of an iron mixture that will suit the whole of his floor for the day.From his own experience he generally alters his cupola charges during the cast, endeavouring to meet at the same time the requisite metal composition for the castings he is about to pour.The founder on repetition work is in a much better position to stabilise his methods, arrive at a certain pig-iron' analysis, regulate...

Jan 1, 1926

The Jacobs Sliding Floor (Floor) is experiencing a surprisingly long competitive life. The first Floor was used on the Camino Tunnel in California in 1960. At that time the Robbins Company had built only seven TBMs, and the future for such machines was considered doubtful by many, as compared to drill and blast methods. This was then, and still is, commonly called the "conventional" method. Robbins' TBM No. 8 was for the Hydro Electricity Commission of Tasmania (HEC) for their Poatina Hydro Project in 1961. In this writer's view, the Poatina experience was the start of successful hard rock boring machines. But, by coincidence, the HEC is using the newest Floor for their King River Hydro project, where driving with the Floor started in July 1986 on the King Tunnel. This paper examines the history and developments in both Floor design and other "conventional" tunnelling equipment, and the site specific conditions that have allowed this old concept to still be competitive in certain select situations. Parametric costing data and some actual progress records are included.

Jan 1, 1987

By N Nosaka

Sinter plants currently have to use many types of ores with different properties due to the great demand for iron ores, which was driven by the massive growth in Chinese iron and steel industry. On the other hand, the development of iron ore mines is limited and the quality of iron ores is in a tendency of deterioration. Therefore, the quick evaluation of iron ores has become more important for a stable sintering operation. In addition to such a background, the CO2 gas emission should be decreased from sinter plants according to the Kyoto Protocol on reduction in greenhouse gases. The present paper first describes the methods for testing the metallurgical properties of iron ores, which use a small volume of sample mainly focusing on magnetite ore that is effective for reducing CO2 and NOx emissions from sinter plants. The sintering properties of ores are evaluated separately according to each stage in sintering process, that is: heating stage before melt formation, primary melt formation in adhering fines layer of pseudo-particles, and assimilation of nucleus ore particle with calcium-ferrite system melts.Next, the application of the tests to the blending ores is introduced showing examples of the studies on the effective usage of the magnetite ores with Marra Mamba type ores.

Jan 1, 2005

Mixers are commonly used for the transfer of oxygen in gas-liquid-solid reactions in minerals processing. The process rate is usually controlled by two steps: gas-liquid mass transfer and reaction kinetics. Some examples are described along with the factors used for analysis of the mass transfer design problem. Typical oxygen rates and appropriate types of aeration systems or mixers are reviewed. The commonly used Rushton turbine has limitations in a number of mineral processes. The development and characteristics of the LIGHTNIN A315 axial flow gas dispersion impeller are described. Some practical examples which highlight its advantages are briefly described.

Jan 1, 1992