Search Documents

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By Aiming Z, Shenyi S, Xialei W

Zhangmatun Iron Mine is situated in the suburbs of Jinan city. Shandong, China. Because of surface environmental constraints, no suitable site can he selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a double- shaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two scopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining.

Jan 1, 1998

By J Rostami, T Afshar, M Sharifzadeh

Accurate estimation of rock load and selection of types of ground reinforcement to match post-failure behaviour of rock mass are important issues to assure tunnel stability. This paper focuses on the main factors affecting rock load to evaluate the capabilities of the existing models for prediction of rock load. Rock mass properties, project features and excavation method, as well as ground conditions and stress condition were found to be the key factors affecting the magnitude of rock load. Field data from tunnels of about 37.5?km driven in several geological structures in non-squeezing ground was used in this study. An in depth statistical analysis was performed on data to find correlations between the input parameters and measured/observed rock load. A weighting system was proposed to obtain the proper contribution of each factor for estimation of rock load in tunnelling through various ground conditions. The new classification system offered predicted values for rock load that were in a good agreement with the actual field measurements. The high disturbance factor (D>0.4) was the prime factor which controlled the rock load. Rock mass quality was the second key factor influencing rock load, which could be estimated by GSI, GSIresidual , especially when combined with tunnel depth.CITATION:Afshar, T, Sharifzadeh, M and Rostami, J, 2014. Estimation of rock load for tunnels with different disturbance factors, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G J JAMESON

The flotation cell has undergone a number of changes since the process was first introduced in Broken Hill in the early years of this century. The development of the mechanical flotation cell is reviewed, followed by a discussion of more recent developments such as the flotation column, the air-sparged hydrocyclone, the Wemco-Leeds cell, the Bahr and Deister columns and the Jameson cell.

Jan 1, 1992

By D Fukuda, K Kaneko, R Kudo, J Kodama, Y Fujii, T Sasaki

"Estimation of stress state as well as elastic modulus is important for the prediction of a rock slope deformation in an open pit mine since it can strongly influence the mining-induced deformation of the rock slope. This study applies a method to evaluate regional stress state and Young’s modulus by analysing the mining-induced deformation of ground. The effect of changes in regional strain state due to tectonic plate motion can be accounted for using the proposed method. Mining-induced deformation can manifest itself as changes in ground surface geometry resulting from mining activity. There are three underlying factors that can contribute to the deformation: displacement induced by the effect of gravity displacement induced by the effect of horizontal regional strain incremental change in the horizontal regional strain. The relative displacement arising from the mining excavation at the Torigatayama limestone mine in Japan has been measured by Global Positioning System (GPS). Both the regional stress state and Young’s modulus were estimated by back analysis of the change in distance between GPS stations using a 3D finite element method. It was shown that the reliability of the estimation improved with an increase in displacement due to mining progression. It was also shown that values for Poisson’s ratios of less than 0.10 are reasonable estimates with values for Young’s modulus between about 5?GPa and 10 GPa. The magnitude and direction of the maximum compressive stress in the district surrounding the Torigatayama mine were estimated to be between -6.4 MPa and -4.4 MPa and around N25E respectively.CITATION:Kodama, J, Sasaki, T, Fukuda, D, Kaneko, K, Fujii, Y and Kudo, R, 2014. Estimation of regional stress state and Young’s Modulus of ground at Torigatayama Limestone Mine in Japan, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 135–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By Atalla YM

Steel rolling mill product finishing pro cesses gradually become or often already are unsuited for current production and marketing conditions. Indications are made as to what has been done to (i) rectify situations of this kind and, (ii) to reduce both product finishing time and costs. The principal features of two separate case studies are reviewed, these being (a) the finishing-end of B.H.P.'s Newcastle o.2 Merchant Mill and, (b) a mixed functions finishing yard and warehouses group (known as he Merchant Mills Loading Yard) which has been perating for a number of years. The areas in ach case are identified as a system while the arious functions, principal product streams nd processing equipment are respectively iden- ified as sub-systems and system elements. etails are given of the models used in each Sub-system dependency on the system as a le is traced by means of an information and ision analysis or by time studies and the sonableness of the system elements is deter- ed by computer programming or by simple com- ison methods. The-accumulated data is used derive improved mill finishing-end or Load Yard,functioning concepts according to pro- rules whilst at the same time considering

Jan 1, 1975

By K Aikawa, M Ito, K Mitsuhashi, Y Ebisu, J V. Satur, I Park, N Hiroyoshi, T Suto

Copper concentration using flotation is becoming more difficult, because of an increase in ore complexity accompanied by smaller grain sizes of copper minerals than usual, requiring finer grinding in order to liberate them. Project Arqueros, located at the mid northern part of Chile, is a copper mine project with an orebody consisting of various sulfides such as chalcopyrite, chalcocite, and bornite. Some of the copper minerals in Arqueros show low floatability mainly because of their fine grain size and resulted fine grinding size, and also because of the complex mineralogical composition. For example, chalcopyrite in Arqueros floats less than the other copper sulfide minerals. In this study we carried out some kinetic flotation tests with the Arqueros ore using a laboratory-scale forced air type flotation machine by varying the regrinding size. The products were assayed and mineralogically analysed to compare the minerals in their flotation behaviour with respect to size classes and liberation classes. The results were compared with a model calculation according to bubble size measurement. From the flotation testing and mineralogical analysis, it was found that copper minerals of the same size and liberation class floated at the same rate even with different regrinding size. At the same time the comparison between experiment and calculation showed that the fine particles of less than 5 µm size floated faster in actual than in the model applied. These results suggested that interactions among minerals of different species and of different sizes had positive impacts on the flotation rate of the fine particles. It indicates that this phenomenon can be applied to improve copper recovery in the project.

Aug 24, 2022

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By F Soleimani

Coal and gas outburst is a common hazard in coalmines and due to the complexity of its nature, efficaciously predicting the possibility of its occurrence is intricate. The mechanical and gas flow properties of coal, in situ and mining-induced stresses and geological structure are involved in outburst occurrence, whereas suggested thresholds for its prediction do not consider them all. Numerical modelling is known as an effective method that can not only consider couple the effect of different physics but also analyse the effect of associated parameters. In this paper, a coupled fluid flow and geomechanics model has been developed in COMSOL Multiphysics to simulate outbursts by considering the effect of gas pressure and composition, damage mechanics on related coal properties, and progressive excavation and mining-induced stress. For the proposed fully coupled outburst model, the effect of pore pressure and sorption are applied to the stress while the influence of stress changes and damage are considered in updating coal porosity and permeability in each time step. In addition, to study the effect of mining-induced stress, the excavation process is simulated by changing the material properties over time according to the schedule of heading development. Then, outburst initiation is analysed from the energy point of view by using the concept of energy conservation law. The simulation results are used in calculating energy sources of the outburst initiation, also, the effect of particle size and ejection velocity are studied, and the significance of particle size effect on the energy analysis and deformed coal on outburst initiation is discussed.

Oct 12, 2022

By Abishev D. N, Balakirev V. F, Davydov G. I

The problem of recovery of cobalt products from poorly oxidised nickel ores (Kempirsaisk deposit) and pyrite concentrates with a low content of cobalt (Sokolovsk-Sarbaisky deposit) has not been solved to the present time in Kazakstan. The balance reserves of nickel ore of the Kempirsaisky deposit make up more than 35 million tons with a nickel content of 1.13 per cent and cobalt content of 0.05 per cent; besides there are 110 millions tons of out-balance ores (Anon, 1995). In a tailing dump of Sokolovsk-Sarbaisk Mining and Productional Association more than 320 million tons of tailings of wet magnetic separation have accumulated, which contain 7.2 per cent of sulphur, 0.022 per cent of cobalt, 0.012 per cent of nickel, 0.094 per cent of copper, 0.079 per cent of zinc, 16.45 per cent of iron, and from which a high quality pyrite concentrate car) he separated through flotation, containing 48 - 50 per cent of sulphur, 44.15 per cent of iron, 0.141 per cent of cobalt, 0.07 per cent of nickel, and 0.10 per cent of copper. The well-known technological flow charts for cobalt and nickel recovery from the tailings of sulphide-magnetite ores dressing (to give pyrite concentrate) and from oxidised nickel ores, are not profitable at the existing prices for metals, but are not worthless and require significant capital investments for the realisation of their value. The flow chart `sulphate roasting - leaching - solution processing' is used widely for combined processing of cobalt-containing pyrite ores and concentrates.

Jan 1, 1996

By Tamura S, Maekawa M, Nagai C, Deguchi M

Heavy fuel oil has been injected into blast furnaces in order to reduce the coke rate, to improve productivity and to control the furnace heat condition. However, in the first oil crisis at the end of 1973, it became necessary to develop an injection technique of new fuels into blast furnaces to reduce oil consumption. In Kobe Steel, Ltd., it was thought that the injection of a coal-oil mixture (COM) into blast furnaces could be developed in a shorter time than pulverised coal injection. The development of this technique was under- taken in 1974, and COM was injected through two tuyeres of the No.3 blast furnace at the Kobe works in 1977 and 1978. In addition, in order to study the combust- ibility of COM and the phenomena in the tuyere zone, the development of a gas sampling method was under- taken in 1975. In this paper, the results of the injection tests and gas sampling tests are reported.

Jan 1, 1981

Most compact bucket wheel excavators in use are in the small to medium range. Large compact bucket wheel excavators compete directly with con- ventional longer boom excavators which have operational advantages over the large compact. There are, however, situations where the large com- pact excavator is viable. In the development of these large compacts there are a number of technical features to be addressed. In addition the SECV now propose to expand the concept to a large compact bucket wheel excavator with a bridge and loading unit for their Loy Yang Open Cut.

Jan 1, 1989

By P Micale

Geological data provides the foundations for the mining value chain. It is used to underpin the modelling and planning and consequently optimise downstream business decisions. However, it is often forgotten or taken for granted. End users often assume the data to be sound without verification. Geological data can be considered a company’s number one asset. Subsequently, the storage, use and management of this data need careful curation and time invested in preserving and protecting it. An established polymetallic mine with 20 000 drill holes could have a data replacement value in excess of $500M at 2020 prices, excluding labour and salary costs. The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the ‘JORC Code’) provides guidelines for Public Reporting. Within the code, Table 1 requires discussion around the different types of geological data, its collection and use. What is needed is additional details regarding the validation and integrity of the geological database. A comprehensive guideline specifying minimum geological standards for geological databases has been developed. This expands on the critical points outlined in Table 1 of the JORC Code. This guideline can be used by companies where geological databases are managed in-house or used to assess these services’ outsourcing. This guideline will ensure that geological data is reliable and unadulterated and can be used with confidence. Using this guideline will assist in preserving the investment of geological data in the mining value chain

Mar 22, 2022

By Robinson T

The paper describes a spreadsheet system that enables selection of projects and companies that meet the user's corporate exploration and/or acquisition philosophy. A regularly maintained commercially available database has been used as the basis for this system. It provides an easily accessible efficient com- prehensive search method. The technique enables ranking by various criteria, both technical and financial, to provide groups of projects/companies that are of interest. Initially, target size parameters such as reserves, production and mine life are applied together with geological criteria such as age and deposit type; the significance of the targets in the context of the Australian gold industry is addressed.

Jan 1, 1988

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

An empirical method of estimating dense rock (D.R.E.) equivalent volumes erupted as airfall tephra, described in a companion paper in this volume, is elaborated, and its accuracy discussed. Estimates obtained from a single eruption can be classified as to whether they show positive, negative, or constant relative dispersion. For positively dispersed tephras (estimated volumes increasing with distance), this procedure improves the accuracy of the method. The technique is applied to selected andesitic tephras erupted from Egmont Volcano, New Zealand, during the last 28 000 years, which are found to range in volume from about 1.5 x 107 m3 up to about 2.4 x 108 m3 D.R.E. With a factor of about 16 between the smallest and largest volumes, this contrasts sharply with the rhyolite volcanoes in New Zealand, where the difference factor is usually of the order of 100. The largest tephra eruptions at Egmont are small compared to the largest debris avalanches, which have exceeded 1010 m3 (10 km3) in volume.The magnitude versus frequency relationship, calculated using a maximum likelihood method, establishes the limits of eruption magnitude at Mt Egmont as 107 to 109 m3 D.R.E. For some volcanoes, the magnitude-frequency relationship changes with time, owing to clustering of eruptions, separated by long dormant intervals. Ngauruhoe Volcano, New Zealand, is an example. Within eruptive episodes, the mean interval between eruptions of >_ 105 m3 is about 0.9 ¦ 0.65 years. The mean interval between eruptive episodes in which >_ 106 m3 is erupted, including episodes in which this volume is erupted gradually, is about 25.8 ¦ 6.6 years, and the mean dormant interval between all episodes is about 5.2 ¦ 3.0 years. At present Ngauruhoe is in an unusually prolonged dormant period, 50% longer than any in the historical record, since 1839.

Jan 1, 1990

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By C G. Ryan, D R. Cooke

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow-level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-chalcopyrite samples yield a narrow range of δ34 SCDT values (-1.0 to 0.9 ë; n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). Vein quartz from the mineralised zone at Waitangi yields δ18OSMOW values from 6.8 to 12.7 ë (n=23). Fluid inclusion studies indicate a homogenisation temperature range of 190¦ - 296¦C and salinity range of 0.2 - 3.0 wt per cent NaCl equivalent. Similar temperature and salinity ranges have been recorded for the other gold deposits in the Coromandel Peninsula. PIXE (Proton Induced X-ray Emission) analysis revealed that the Waitangi ore fluids have 1090 - 2700 ppm K (average 1600), 145 - 205 ppm Ca (average 180), 80 - 100 ppm Mn (average 90), and 80 - 200 ppm Fe (average 120) but no detectable Cu, Zn, Br, Rb, Sr, Pb and Bi (only one fluid inclusion contains 28 ppm Zn). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source (either directly, or by leaching of igneous sulphides). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1 - 5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in δ18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Mixing of ore fluids with convective ground water is a likely mechanism for gold deposition in a shallow environment for the Waitangi vein system and there is also lack of fluid inclusion evidence (eg liquid-rich and vapour-rich inclusions in the same growth zone) for boiling of ore fluids. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that δ18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1999

By H Jalalifar, N Aziz

In the ten years since the University of NSW proposed a pillar design methodology for bord and pillar operations, the Australian coal mining industry has changed substantially. What was primarily a bord and pillar design approach is now being applied to chain pillar design in longwall mines where the requirements are substantially different. The dimensions of chain pillars can impact on tailgate conditions (roof, rib and floor), seal performance, and surface subsidence. The status of chain pillar design practice in Australia is reviewed, with a focus on defining pillar strength, chain pillar loading, and assessing the performance of the roof/pillar/system. A new pillar strength equation is proposed for Australian coal that applies for all width/height ratios. An alternative analysis of probability of failure of chain pillars is presented.

Jan 1, 2005

By Egan J. R

Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant testwork conducted in 1990 - 91 indicated that concentrate grades would be substantially improved by reducing the particle size (Pao) of the lead from 38 to 15 ¦m and the zinc from 45 to 24 ¦m. Circuit revisions involved installation of major new equipment including: two 600-kilowatt Vertimills for regrinding, a four metre diametre column flotation cell and a four metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were Reassigned.

Jan 1, 1993