Search Documents

The building is a lofty, well-ventilated one of hardwood frame, with galvanized-iron walls and roof, and consists of five spans running north and south, covering a total length of 236 ft. Each span is composed of nine bays of 1:3-ft. centres, making the total width of the building 117 ft. The refinery is situated conveniently at a distance of 100 yds from the smelters. Through the third span of the building runs a 5-ton electric overhead travelling crane, of a 3-motor type, with a span of 29 ft. The crane runway extends over a railway line, which connects the smelters to the refinery. This crane is llsed for handling bullion, coal, melting kettles, lead pumps, &c. A 3-ton crane of similar type, but with a 50-ft. span, runs through the fifth span of the building and also extends over the railwav line alreadv mentioned. This crane is used to load the soft lead into railway trucks, or to stack lead awaiting shipment in the area covered by the crane's operations.

Jan 1, 1918

By L Mariano

Three selected iron ore samples from the major bedded and channel iron deposits of Western Australia were analysed using a scratch test commonly used in the oil and gas industry. The portable commercial equipment dubbed Wombat cuts a groove on the surface of the sample with a cutter under imposed depth of cut and cutting velocity. The normal and tangential components of the force acting on the cutter are recorded with a high degree of precision (about 1N) at fine spatial resolution of about 20 measurements per millimeter.The intrinsic specific energy inferred from the scratch test measurements is found very well correlated with a classical measure of strength such as the uniaxial compressive strength, for over 300 sedimentary rock samples.The results obtained on the iron ore samples are comparable to those obtained on oil and gas sedimentary rocks. This method could provide an objective and semi-automated measurement of material strength and brittleness in iron ores that can possibly be correlated to the lump to fines ratio.

Jul 11, 2011

Declines for both access and rock haulage are replacing shafts for mining relatively shallow deposits of down to 1000 m below surface. Where the orebody does not outcrop and where surface access may be restricted, it is often necessary to drive long dead end headings before a connection can be made back to surface and a ventilation circuit created. In hot tropical areas and where large diesel powered equipment is used for mining, heat may also be a problem at these relatively shallow depths. The normal design criteria based on statutory limits and good practice used to evaluate ventilation and cooling requirements in terms of air velocity, dust, gases, diesel exhaust dilution, re-entry after blasting and heat stress are described in this paper. These are then used to design and cost alternative auxiliary ventilation systems that include leakage based on general fan performance curves and typical duct systems. The implications of the current European Community recommendations regarding nitrous fumes are also briefly considered. The actual problem relates to a 2100 m long decline that may have to be extended to 3000 m long without a connection to surface or through ventilation and is located in a hot tropical area where the surface wet bulb temperatures may exceed 25¦C for more than a third of the summer period. Once the preliminary ventilation design is completed, the auxiliary ventilation system can be modelled and simulations undertaken that incorporate heat and moisture transfer routines with the objective of determining the cooling load and amount of refrigeration required. Cognisance is taken of cyclic diesel operations and the thermal flywheel effect of the surrounding rock on the wet and dry bulb temperatures resulting from these operations.A suitable modular cooling system located at the portal is described and optimised with capital and operating costs of both the ventilation and cooling systems provided.

Jan 1, 2005

The purpose of this paper is to list by tabulation and flow sheet, the operating equipment and installations in use at Rosebery, and to refer to particular items which may be of interest for purposes of comparison, or because they possess some unusual feature. The general perspective has been taken from the viewpoint of operating and maintenance experience.The sequence begins with ore breaking and transport and proceeds through milling operations. The paper is in two sections, first, mechanical equipment, second, electrical equipment. A brief outline of a scheme for using gravel wash for stope filling, which is in course of installation, has also been given.

Jan 1, 1949

By Johnson MT

The microprocessor revolution of the 1970's dramatically improved the price/per- formance of graphics hardware. Together with improved communications and new software concepts and standards this has resulted in the emergence of a new tool with particular application to the mining industry. The Distributed Graphics Processor (DGP) offers more natural means of interaction with com- plex technical models.

Jan 1, 1983

The concept of Extreme Gravity is the latest in a series of innovations that has seen a re-introduction of gravity recovery systems into the milling operations of most gold mines. Traditionally, most gold milling circuits are designed around flotation and cyanidation requirements, with the gravity circuit being fit in where possible. Extreme Gravity takes the novel approach of optimising the circuit, in order to maximise recovery by gravity. In some cases gravity systems can achieve high enough recoveries to eliminate the need for chemical systems such as cyanidation or flotation. There are many advantages of such a system including low capital cost, reduced permitting, improved cash flows and much reduced environmental issues. There are a number of plants currently in operation which utilise this new methodology. The Muzhievo project has been an example of a recent turn key success achieving recoveries from 85 - 90 per cent. The details of this project are examined as a case study.

Jan 1, 2000

By D Wei

Large tonnages of low-grade haematite ores need to be treated every day in China. One of the mineralogical characteristics of these haematite ores is that the grain size of haematite is smaller than that of quartz and is not uniform in the ores. Therefore, a flow sheet consisting of gravity concentration, low-intensity magnetic separation, high-intensity magnetic separation and reverse flotation is mainly used to separate haematite ores in China, to obtain acceptable beneficiation performance and reduce the operating costs. Nowadays, whether based on mineral processing practice or theoretical analysis, the results show that the application of the above-mentioned flow sheet is able to take full advantage of these mineral processing methods and achieves satisfactory benefi ciation of haematite ores. For example, when the iron grade of the haematite ore is about 29 per cent Fe, a concentrate assaying 68 per cent Fe can be obtained and the recovery of iron is over 80 per cent. In the future, research work on the beneficiation of haematite ores should focus on investigating the most feasible particle size for gravity concentration circuit feed so that the operating costs can be reduced and ultimately the separation performance can be improved.

Jul 11, 2011

A research and testing facility has been developed at Simtars to allow the spontaneous combustion testing of coal on a large scale. In this adiabatic reactor, the coal particle sizing is closer to that which could be found in the goaf and therefore the reaction is more likely to simulate the underground situation. This allows aspects of the spontaneous combustion process and methods for detecting a heating to be investigated which cannot be done in an operational mine. Up to 18 tonnes of run of mine or crushed coal is loaded into the reactor and allowed to self-heat while the temperature and gas profiles within the coal pile are monitored. The gases evolved from the coal are analysed using a fixed gas monitor system and gas chromatography to determine which of the common mine fire indicators and ratios can be used to predict the onset and progress of coal heatings. Benchmarking of the inherent propensity of a coal to spontaneously combust at both the large- and laboratory-scale is also possible by comparing the sample against previously tested samples. It has been found that the coal particle size affects both the time it takes for the coal to react and the location of the developing heating. The heatings generate approximately one metre from the inlet but in the crushed coal case do not progress to an advanced heating stage until the æhot spotÆ migrates towards the coal surface where there is an increased oxygen supply. Physical properties such as the compressive strength of the coal also affect the heating size and the time it takes for a heating to develop. Higher strength coals appear to oxidise more slowly and therefore take longer to self-heat as oxidation of the coal is the heat-generating step in the spontaneous combustion process. The best indicators of the state of the heating were found to be CO make and GrahamÆs ratio which are independent of air flow. Investigation of a potential spontaneous combustion should begin as soon as the CO make or GrahamÆs ratio exceed the background levels. The results from the tests undertaken on a number of Queensland and NSW coals are reported here together with the implications for the mining industry.

Jan 1, 2005

By Voss Smith F, Matters C. W, Slee R. T, Coldham JC, Davies HW, Wallman H. H

The Committee desires to thank the managers of the various mines along the line of lode for their hearty co-operation in its labours. It would also extend thanks to Messrs. J. O. Moulden, Howchin, Twelvetrees, and the West Australian Geological Survey for various information; to Messrs. J. G. Dreyer, S. Pope, T. Read, P. Moncrieff, R. Williams, and W. J. Rose for analyses; and to a number of local gentlemen for advice and help. Professor Skeats, of the Melbourne University, gave much valued assistance in petrology, and Mr. Herbert Lavers kindly undertook the study of the garnets.INTRODUCTIONThe famous Broken Hill lode is situated in a low range of hills, the Barrier Ranges, near the western border of New South Wales. It has been worked since 1884-first for, silver, then for silver and lead, and at present for lead, silver, and zinc. No excuse seems necessary for placing before members even an imperfect report on the geological features of this notable ore deposit, since so little work has been done on the subject as to constitute almost a national reproach. This is the more deplorablesince the evidence laid open by mining operations is destroyed almost as soon as it is exposed, and there exists the real need of a continuous and connected record of geologieal developments.

Jan 1, 1911

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

By Vestre J, Kure K, Bergqvist I

Existing practical laboratory tests for comparative strength determination of commercial explosives consist of the lead block test, the ballistic mortar test, the bubble test etc. These tests are carried out in material with quite different properties compared to rock. The theoretical performance potentials of commercial explosives are traditionally described by weight-strength (WS). Some explosive producers use the Langefors formula for weight-strength calculation, where also the gas volume is considered. Neither the theoretical nor the practical methods for determination of explosive performance such as the above, give good enough prediction of fragmentation and heave in rock blasting. For these reasons a project was started for the purpose of finding a small scale test method which predicts how different explosive parameters affect fragmentation and heave. Small scale tests were carried out by using 50 cm cubical blocks, mainly of concrete, but a few also of rock. All blocks were blasted in a steel cylinder with a diameter of 1.2 meters. The velocity of detonation was monitored, and the velocity of fragments was derived from their time of arrival at the steel wall, which was registered by accelerometers. After blasting all fragments were screened. The charge diameter was 22 mm and the amount of explosive 78 grammes, resulting in a specific charge of 0.62 kg/m3. Explosive properties such as energy, gas, VOD and density were systematically changed.The results presented in this paper show how fragmentation and heave systematically change when the explosive properties like energy, gas, VOD and density are systematically changed. The results from the small scale tests are compared to full scale tests carried out in tunnel blasting, and during summer 1990 also in bench blasting.

Jan 1, 1990

By Harada M, Katsuta S

In order to shorten the time taken to com- plete shield tunnel excavation work, reduce labor costs and to improve safety, an automatic assembly robot system for the segments used has been developed. It was developed in the three years from 1982 until 1984. An experimental assembly system for concrete segments (outer diameter:.3.55m) has been thoroughly tested to confirm that these segments can be fed and assembled automatically (Fig. 1, 2). This report outlines the robot which will be put into practical use in the near future. The robot senses the position of already assem- bled segments by means of position sensors, controls the position and the attitude of the segment to be assembled to allow bolt hole positioning, and completes the automatic assembly of a se;nent by automatically tighten- ing bolts. The six segments which make up one ring can be automatically assembled in about 25 minutes.

Jan 1, 1987

By M Norbert, C Bennett

The Legacy Way Tunnel was constructed from Toowong to Kelvin Grove in Brisbane, and is the first large-scale underground excavation in the Bunya Phyllite in Brisbane. The Legacy Way Tunnel is 4.3 km in length, comprising two mainline tunnels excavated by a tunnel boring machine (TBM) with 46 connecting passages excavated between the mainline tunnels for egress provision and services. The Legacy Way Tunnel passes through two geological formations, the Bunya Phyllite and the Neranleigh Fernvale Beds. The Bunya Phyllite is the dominant formation of the Legacy Way Tunnel, extending for three quarters of the tunnel prior to intersecting the Normanby Fault Zone (NFZ) and the Neranleigh Fernvale Beds. The NFZ forms the contact between the two formations as part of the Brisbane Metamorphics, which underlies the majority of Brisbane City. The development of the geological model and the understanding of the ground’s reaction to tunnelling was an iterative process. The tender phase investigation data has been supplemented with additional design phase investigation boreholes, geophysics and walk overs. Aerial photograph interpretation coupled with borehole data allowed the development of the domains along the length of the tunnel. Early excavations for the spoil conveyor tunnel and borehole data from subsurface instrumentation installation provided the first construction phase data followed by the commencement of tunnel boring machine (TBM) excavation. Routine cutterhead inspections coupled with ongoing reviews of the predicted geology resulted in clear response triggers to selection of segment types while detailed inspections in passage locations provide the initial classifications for segment removals.CITATION:Bennett, C and Norbert, M, 2014. Tunnelling within the Bunya Phyllite of Legacy Way, Brisbane, Queensland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Massacci P

A review has been made of the studies focusing on methods for the description of grain -size distribution after breakage and, separa- tely, of the degree of liberation of the miner- al species making up the various grain-size classes of comminution products. The purpose of the study has been to de- velop an overall model of the phenomenon which, owing to the very effect of comminution, leads to the formation of grains that are generally of mixed composition. A calculation procedure has thus been de- veloped for the liberation function taken as the assessment of the distribution of mix com- ponents in the products obtained after a commi- nution process. The aim is to identify a func- tion which may, to a certain extent, simulate the variation of the grade-recovery function of an ore in relation to its degree of comminu- tion. The numerical model thus obtained has been tested out on results obtained experimentally.

Jan 1, 1986

By Stewart R. D, Lawrence W, Youl M. J

The trend towards contracting by major coal mining companies such as BHP Coal and MIM Ltd is examined. Reasons why this trend is occurring are discussed and the concept of partnering is examined. Two case studies are given: the Mt Owen Mine in the Hunter Valley, NSW and the South Walker Creek Mine in the Bowen Basin, Queensland.

Jan 1, 1997

To finalise the arrangement and details of the headframe to be erected over the new No. 3 Shaft, the haulage and winding equipment requirements were first determined, then tentative designs were prepared to cover the needs of general shaft servicing work for men and materials, mullock and ore handling, and the probable requirements of a breaker station to be built adjacent to the headframe, which would provide for the crushing of the run-of-mine ore down to a size which would be suitable for feeding on to the concentrating mill.

Jan 1, 1957

By B Reynolds

The process design for green- or brown-fields metallurgical plants typically starts with two fundamental elements: the detailed mass and energy balance and the plant flow availability. The detailed mass and energy balance is generally developed using process flow-sheet simulation software and represents the steady-state operation of the plant at normal operating conditions. The plant flow availability, also known as a range of other industry-specific terms such as ‘flow availability’ and ‘operating factor’, describes the ratio of plant production to the steady-state mass balance. These elements are then used together as the basis for equipment selection and design.Plant flow availability takes into account a myriad of production loss factors including planned and breakdown maintenance, feed availability and composition changes, variability in operational performance and the interaction of batch and continuous unit operations. The combined impact of these loss factors are complex and as such plant flow availability is usually derived using a top-down approach such as comparison to an existing operation, a group of similar operations or to an anecdotal ‘industry leading’ benchmark. These top-down approaches are fraught with risk however, as they cannot factor in changes to equipment selection, flow-sheet or plant operating philosophy, and can result in over-expenditure of scarce capital or shortfalls in plant production.The use of dynamic simulation to provide a bottom-up alternative to quantifying the plant flow availability in metallurgical plant design has been growing rapidly in recent years. It provides a technique to quantify the combined impact of the loss factors described here and a tool to support process design and equipment selection by facilitating a range of sensitivity and what-if analyses. This paper presents a case study of how dynamic simulation has recently been used to support the

Aug 8, 2011

By T Takayama, R Muroi, M Matsumura

The steel industry occupies 14 per cent of CO2 emissions in Japan, and the sintering process is one of the major emitters. Since most of CO2 released from the sintering process comes from coke fine combustion, replacement of coke fines with biomass char as bonding agent is a potential countermeasure. In order to explore the effective use of biomass char, we chose char made from Palm Kernel Shell (PKS) as a sample. First, the char’s combustion behaviour was examined with varying the char’s particle size by means of admixing the char in alumina ball packed bed placed in an electric furnace. As a result, the finer the PKS char the faster the burning rate and reaching a higher temperature compared to coke fine. In addition, it is also concluded that the optimum size of PKS char was larger than coke fines. Next, the effect of different heat profiles on sinter structure was examined by sintering tablet made of chemical reagents. In this experiment, the chemical composition is designed based on sinter composition. By this sintering test, even at high temperature, rapid cooling is effective to make fine sinter matrix and fine pores, which has possibility for high sinter reducibility. Based on these two experiments, using PKS char as a sinter fine source has the possibility to improve sinter reducibility.

Nov 8, 2021

By Hebbard GJ

Vertical crater retreat mining is being used at Zinc Corporation, Limited and New Broken Hill Consolidated, Limited for pillar recovery between previously mined and filled stopes. In order to increase productivity in the older lead lode areas of the mine, particularly in the lower grade sections around the keel of the orebody, score form of longhole stoping was considered necessary.Due to poor ground conditions in the country rock surrounding the ore and the requirement to provide sane wall support during mining, primary VCR mining has been utilised in these areas.At Zinc Corporation, several stopes have thus far been mined by a hybrid longhole stripping - VCR method.

Jan 1, 1985

By Kissell F. N, Volkwein J. C

The U.S. Department of Interior's Bureau of Mines has the opportunity to visit many U.S. mines, including some that claim 2 to 5 times the national average of 334 raw tonnes/unit shift (tps) from a continuous miner section. In a project to assess the reasons for this high production, the Bureau conducted two studies. The first study focused on the 25 highest producing continuous miner sections. What stood out during the visits-was the quality of the labor-management relations. In each of the mines there was a positive labor/management relationship based on mutual trust and a sense that the employees were the company's most valuable resource. Discussions with labor revealed a universally positive attitude toward the company. Interviews with the mine superintendents invariably ranked the quality and attitude of workers as more important than anything else. Also during the mine visits of the 25- mine study, no engineering factors obviously stood out. Time at the face was greater than average, most were in coal over 1.52 m and the roof was generally good. Also, none of the 25 mines had to contend with high methane levels. Because this study found that a high percentage of mines were in seams less than 1.52 m thick, the second study examined thin seam mines only.

Jan 1, 1988