Search Documents

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite,* and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe2O3) and maghemite (gamma-Fe2O3) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, however, occurs largely as goethite (Fe2O3-H4O) and hematite (Fe2O3) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated. MAGNETIC ROASTING Hematite undergoes a stepwise reduction when exposed at moderately elevated temperatures to a reducing atmosphere containing hydrogen or carbon monoxide: Fe2O3? Fe3O4 ? FeO ? Fe Since the desirable product in magnetic roasting is Fe3O4, the conversion is halted after the first stage by controlling the reduction potential of the gas mixture with water vapor or carbon dioxide. The reducing gas mixture must be such that the oxygen partial pressure at the solid-gas reaction interface will be maintained intermediately between the oxygen partial pressures in equilibrium with Fe2O3 and Fe3O4 at the prevailing temperature. Because of the rapid increase in decomposition pressure of Fe3O4 with increase in temperature, the practical upper limit of useful reaction temperature is about 1400°F, above which over-reduction usually occurs in atmospheres containing hydrogen or carbon monoxide. On the other hand, useful reaction rates usually occur only above 800°F. Goethite reacts similarly except that the combined water probably has to be driven off thermally before the reduction to magnetite occurs. Iron carbonate must also be decomposed thermally to an oxide before conversion to magnetite. Iron silicates are apparently not amenable to magnetic roasting. The rate of penetration of the reaction toward the interior of a given ore fragment is dependent on the chemical composition and physical structure of the solid. Most ore fragments tested here reduced satisfactorily to 1/4-in. depth in less than 14 min at 1200°F. Some very dense fragments, however, were reduced to less than 1/32-in. depth under the same conditions. Determination of the optimum temperature, gas composition, ore fragment size, or time of exposure

Jan 1, 1961

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

By R. H. Widmyer, G. M. Wood

This investigation was prompted by the absence of a simple, accurate method to predict optimum second stage separation pressure in three stage separation operations. Three stage separation as used here includes two separators plus the stock tank. The first stage pressure is usually fixed by gas sales conditions and the third stage is at atmospheric pressure. Thus, the second stage pressure is the only one that may be varied in-discriminantly during production operations. No variations in temperature were considered in this study, even though it will vary among systems, for a change in temperature has little effect on the optimum pressure. Optimum pressures may be determined from flash calculations, but these are tedious unless a computer is available. An early attempt to develop a simpler method&apos; yielded an equation which gave the optimum pressure only as a function of initial and final pressure. Experience, however, confirms theoretical relationships which show that composition as well as pressure and temperature must be a factor. This indicates that the basic relationship should be an equation of the form, where P, is second stage pressure, P, is first stage pressure, A is a function of P. (stock-tank pressure) and the system composition, and n is a function of the number of stages and the system composition. Fig. 1 shows the basic variation of P2 with P for a fixed system composition. A series of such figures clearly showed the effect of composition. The peak of each curve reflects that second stage pressure at which the stock-tank recovery (gal/MMcf) residue gas is a maximum value. DEVELOPMENT OF NEW CORRELATION Wellstreams having 17 different analyses, ranging from low gravity crude to condensate, were used to determine the effect of composition. Each wellstream was flashed through three stages to determine the optimum second stage pressure for each first stage pressure. Equilibrium vaporization ratios proposed by Latham and Campbell were used throughout. The heptane plus fraction, for simplicity, was assumed to have the properties of octane. The results were subjected to an empirical analysis in an attempt to develop a correlation- that would be (1) simple, (2) accurate, and (3) eliminate the need for any flash vaporization calculations. This analysis yielded two equations, one for wellstreams having a specific gravity greater than one (air = 1.0) and one for those less than one. For crude streams (specific gravFor condensate (specific gravity < 1.0),

By R. V. Taborelli, P. B. Bucky

This investigation was carried on by means of models and the application of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimension. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in. bed B, a ?-in. bed C and two ?-in. beds D and E. The model was rotated at + 2350 r.p.m. equivalent to a model ratio of 1268. It was worked back ¼ in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft. and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel ? in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1940

By P. B. Bucky, R. V. Taborelli

This investigation was carried on by means of models and the application of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimension. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in. bed B, a ?-in. bed C and two ?-in. beds D and E. The model was rotated at + 2350 r.p.m. equivalent to a model ratio of 1268. It was worked back ¼ in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft. and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel ? in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1940

By Y. Oka, H. Majima

When a rock particle is subjected to an external force, internal stresses and deformations are experienced by the particle. Assuming that the breakage of a rock is mainly due to tensile stresses generated by the action of a pair of concentrated loads, F, directed in compression towards the loading points at the shortest distance, as illustrated in Fig. 1, the stress and deformation experienced by a particle of irregular shape can be determined with the aid of the theory of elasticity. According to the photoelastic experiments made by one of the present authors,&apos; the stress states in a rock particle of irregular shape are quite similar to that of an inscribed sphere of diameter x, as indicated in Fig. 1, but accompanied by the faint stresses, in the vicinity of the particle outside of the inscribed sphere. Therefore, the stress components in an irregularly shaped particle can be estimated by referring to stress components in a sphere. Applying polar spherical coordinates to an elastic spherical body, as shown in Fig. 1, the stress components are all expressed as multiples of F /x2 and more or less influenced by the loading angle and Poisson&apos;s number m. In general, the energy w, acting on a rock particle is defined as the product of loading compression F

Jan 1, 1970

By Earl L. H. Sackett

Barite, although not a glamour mineral and probably little known to many of those in the mining business, is produced in the US. in very respectable quantities and is an important factor in the mineral economy of this country. The scope of the various uses of this mineral is perhaps one of the most misunderstood things about it, for it is surprising how many of those with a casual knowledge of the subject speak of its primary utilization in terms of paint pigments and barium chemicals. The life blood of barite utilization, however, is the petroleum industry by virtue of its dependence on this high specific gravity, inert mineral as the weighting material in its drilling fluids. From 80 to 85% of barite usage in the U. S. is accounted for in this manner-in fact, its role in oil well drilling is the only excuse for some of the large-scale barite production facilities which have been developed. Other uses are important and widely varied, but comparatively they are of small scale. They include fine crushed barite of low iron content as a component in glass manufacture, barite as a source material for manufacture of barium chemicals, finely divided barite as a component of some rubbers and ground, bleached barite in pigments. The formerly substantial use of barite in lithopone, however, has declined markedly because of replacement of lithopone by titanium pigments

Jan 5, 1962

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By HERBERT G. MOULTON

FROM prehistoric times to our own day man has struggled against extremes of climate. Human life, originating in semi-tropical or temperate areas, was unable to progress into the northern latitudes until fire was discovered and some form of clothing provided. It was found possible to maintain life even in the hottest parts of the tropics, but only at a great sacrifice of comfort and efficiency compared with the more temperate zones, or in cooler areas with the protection of clothing and artificial heat. It was no accident, but the natural result of climatic conditions, that efficiency became the greatest and civilization the most advanced in areas where the natural climate was favorable, or in cooler zones where protection against severe cold could be se-cured by relatively simple methods of conserving or producing heat.

Jan 1, 1933

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By AIME AIME

PRESIDENT BASSETT&apos;S gavel called the Annual Business Meeting to order shortly after 10 a. m. on Tuesday. On motion of Eugene McAuliffe, reading of the minutes was dispensed with and Mr. Bassett read his annual report of the year&apos;s activities as follows : During the year I have visited eighteen of the twenty- seven sections, making an average of GG 2/3 per cent. The invitation to come again has always been extended, but in only one case have I been able to visit the same section twice. Chicago entertained the president twice during 1930. Mrs. Bassett accompanied me on visits to ten sections. Everywhere we have found the most cordial hospitality and a gratifying enthusiasm for the Institute. If anyone had fault to find with the management or felt dissatisfied with what was being done, it was carefully concealed. I am happy to report to you an agreeable, helpful and progressive spirit in each of the sections visited.

Jan 1, 1931

By P. D. I. Honeyman

DURING 1938 many copper companies again felt the economic pinch and smelter operations were often on a reduced basis which some- times resulted in intermittent operations and complete shutdowns. During the last half of the year production was stepped up and smelting operations resumed a more normal appearance. One of the present-day trends in reverberatory sme1ting is definitely toward high-tonnage operations. i\ t the Phelps Dodge Corporation&apos;s Douglas plant, the reconstructed 107 by 26- ft. reverberatory furnaces are operated at the rate of 1000 tons of solid charge per day. The arch, all of silica brick; is sufficiently high above the bath to give

Jan 1, 1939

Jan 1, 1886

By T. C. Craig

For the year 1934, there were 382 oi1 wells completed for a total initial of 146,965 bbl. Fifty-three wells were deepened for a total increase of 8363 bbl., bringing the total volume of new oil to 155,328 bbl. As of Jan. 1, 1934, the daily potential of the field as determined by the Texas Railroad Commission was 159,740 bbl. Of this amount 26,429 bbl. is "marginal oil," and 2682 bbl. is exempt on account of water. In December, 1934, the daily potential was established by the Railroad Commission as being 297,501 bbl. with a daily allowable of 56,800 bbl. Of this amount 31,993 bbl. is "marginal oil," and 2183 bbl. is exempt on account of water. There has been no field-wide test made during the year, and as a result the rated potential of the field is in all probability much higher than the actual potential. As each new well comes in, a five-day test is made under the supervision of the Railroad Commission. The potential thus established is added to the field potential and shares its pro rata part of the market outlet, which is the allowable production, no allowance

Jan 1, 1935

By Charles Jones

IN the winter of 1902, while occupying the position of mining and examining engineer for the Mountain Copper Co., Ltd., of Keswick, Cal., I had occasion to discuss with the General Manager, among other things, the question of the enormous waste of sulphur in smelting cupriferous, pyrite ore, and to cast about for means to utilize this waste or to render the fumes innocuous to vegetation. The decreasing rate of production of California farms, the consequent need of fertilizers, and the opportunity thus offered to utilize large quantities of sulphuric acid in the manufacture of superphosphates naturally brought the subject to the practical and commercial side of phosphates. I was informed that the company had made efforts to find phosphates in the West, without success. I advised as a start placing inquiries for phosphate deposits on the Pacific coast in the current mining ,journals. This was done, with the result that in January, 1903, from an advertisement in the Mining and Scientific Press we got track of a deposit in Rich county, Utah, through T.J . Wilson, of the Southern Pacific railroad in San Francisco. As soon as snow in the mountains would permit, in May, 1903, I undertook an examination of the property, with the result of recognizing the importance of the find, in spite of its lack of facilities for transportation at a commercial figure. On June 15, 1903, I concluded my report by saying, "This may be one of the world&apos;s deposits of phosphates." On Nov. 17, 1903, I concluded my report for the season in the following words : " I have now no hesitation in saying that I believe the Carboniferous formation so largely developed in the Wasatch mountains of Utah and the mountains of the Great Basin will prove to be one of the greatest storehouses of phosphoric acid in the world."

Jan 10, 1913

By A. T. Miesch, L. B. Riley

Distribution of minor elements in sandstone-type uranium deposits of the Colorado Plateau is being studied by the USGS on behalf of the A EC. A primary objective has been to provide basic data which could be useful in geo-chemical exploration for new deposits. The basic statistical measures — similar to those used in sedimentary petrology—are described. The underlying principle is that the frequency distributions fit or approach the log-normal form. Since 1952 the U. S. Geological Survey on behalf of the U. S. Atomic Energy Commission has conducted a study of the distribution of minor elements in sands tone-type uranium deposits of the Colorado Plateau. A primary objective in this study has been to provide basic data which could be useful in geo-chemical exploration for new deposits. Among the basic data considered important are estimates of the abundance and habit of each element in the ore and in the host rocks. It has been found that a few basic statistical techniques, and variations of these techniques, are useful in this type of study. Some of the basic techniques have been used to advantage by researchers in geochemistry and in other fields of geology, especially sedimentary petrology; others have been used to only a limited extent. Among the latter is the linear correlation coefficient, which has proved useful in assessing the element associations in a particular rock type without analysing individual mineral separates. In computing the basic statistical measures a scale has been used which is, in some ways, similar to the phi ($) scale used by sedimentary petrol-ogists in grain-size studies.&apos; FREQUENCY DISTRIBUTIONS It has been recognized for some time that the results of analyses for a given minor element in a suite of samples of rocks or ores yield frequency distribution curves which are approximately normal when the curves are plotted on logarithmic or geometric scales. In other words, the analytical results give an approximate lognormal frequency distribution. A classical example is given by D. G. Krige2 in the study of the distribution of gold values from a mine on the Witwatersrand. Another example is shown in Fig. 1, the distribution of barium concentrations in samples of uranium ore from the Chinle formation. The geochemical data are analogous to grain-size data gathered by the sedimentary petrologist. Both types of data, after simple logarithmic transformations, may be treated by conventional statistical methods based on the normal distribution. This is not to say that other types of transformations may not serve equally well or better for particular element distributions.3 Spectrographers and other analysts are quite aware of the dependence of their precision on the concentration of the element present.4 For example, in the part per million range the variation may

Jan 1, 1961

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

By M. W. BERNEWITZ

IT is 27 years since I last visited Broken Hill, New South Wales, one of the world&apos;s greatest lead-silver-zinc districts. Then, the flota¬tion of ores was in its infancy. The Minerals Separation process had its birth as a practicability in the Central Mill, which is still operating and yielding high recoveries. The average Australian knows that Broken Hill is an important mining center in a "corner" of New South Wales, but he does not know what a factor it is in the lead, silver, and zinc production of the world. Nor does he realize that among the ramifications arising from metal production at Broken Hill are the great lead smelter at Port Pirie, South Australia, 254 miles southeast; the electrolytic zinc works at Risdon, and the limestone mine at Davenport, Tasmania; the acid works at Cockle Creek, New

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935