Search Documents

By C. W. Pritchett

Several years ago, during a trip from Jojutla to Huauatla, in the abate of Morelos, Mexico, I was told by my guide of the ruins of an old smelter near by, and my curiosity was excited to such an extent that I went out of my way several miles to see them. I found them very interesting; and, as I fortunately

Jan 1, 1902

By P. D. Merica, H. Scott, R. G. Waltenberg

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903—1911 by A. Wilm1,2 and have been described by him and by others. 3, 4,5.6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from tempera-

Jan 1, 1921

Jan 1, 1881

By Harold Markus, Gerhard Derge

THE first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from I.I2[t] volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. EXPERIMENTAL DATA Cations.-The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.2 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 0 7-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By R. H. Hawkins

AN investigation of the applicability of geophysical methods to north-ern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines TABLE 1.-Formations Associated with Moose River Basin Maximum System Formation Lithology Observed Correlation Thickness, Ft. Pleistocene Marine clays 150 Glacial till (Minimum Interglacial 30) clay and peat Glacial till Lower Cretaceous or Mattagami Fireclay, sand 138 Kootenay (?) Upper Jurassic. and lignite Devonian (Upper) Long Rapids Petroliferous, 50 Portage and black and gray Genesee shale Williams Limestone and 87 Tully (?) Island calcareous shale Devonian (Middle).... Abitibi River Gray fossiliferous 65 Onondaga limestone Devonian (Lower) ?... Moose Rive- Limestone and 50 gypsum Devonian (Loner) Sextant Arkose, clay, etc. 50 Pre-Cambrian Syenite, granite gneiss, etc. Igneous intrusives. . Lamprophyre dikes cut the Abitibi River and lower formations. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organ-ization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1933

By D. Harrington

WHEN the word gas is mentioned in connection with mining, almost invariably it is inferred that the explosive gas, methane, is in mind and that it must refer to coal mining. While it is true that methane occurs, or is likely to occur, in almost any or all coal mines, it is also a fact that the metal mines of the world have in them by far a greater variety of gases than have the coal mines. In many cases the gases in metal mines are as dangerous to individuals as the gases likely to be found in coal mines; in some instances the metal mine gases are even more deadly. The coal mine is more likely to have methane than the metal mine, in rare instances it may have high percentages of nitrogen or high carbon dioxide, or there may be a deficiency of oxygen where the air is confined in a blind end or in a sealed region; much more rarely there are found in coal mines in relatively small percentages, ethane, or other hydrocarbons with odor of ether, gasoline or kerosene, or there may be minute percentages of hydrogen sulfide. In time of coal mine fire or explosion, there is likely to be high carbon monoxide (4 per cent. or over in some cases) and if the coal contains much sulfur, there may be some sulfur dioxide in the fire fumes. In metal mines there are a number of cases of occurrence of methane and attendant explosions; some metal mines have appreciable percentages of the decidedly explosive hydrogen; in some metal-mining regions carbon dioxide flows into the mine, fills the workings and overflows just like water. In other regions, at many working faces there are high-temperature gases containing a mixture of gases of sulfur (sulfur dioxide, hydrogen sulfide and possibly SO3 in some cases) together with carbon dioxide and nitrogen, and the deadly hydrogen sulfide in lethal proportions is found in some high-sulfide metal mines at blasting time. Carbon monoxide constitutes a decidedly dangerous day by day hazard in connection with metal-mine blasting, because of the heavy charges of dynamite that are used and the use of fuse, which in burning gives off much carbon monoxide. The poisonous gas hazard is accentuated because of the relatively small openings where metal-mine blasting is done and to the inefficient ventilation of the usual metal mine.

Jan 1, 1930

By R. S. Dean

THE first attempt to establish an equilibrium diagram of the lead-antimony series was made by Roland-Gosselin1 in 1896. This investigation classified the system as a purely eutectiferous one, with the eutectic at 12.5 per cent. antimony and 228° C. In the next year, Stead2 placed the eutectic temperature at 247° C. The error in temperature made by Roland-Gosselin, however, has been perpetuated in the literature with a remarkable degree of persistency; this value was accepted by Campbell (1902), and Ewen (1910),3 and will be found in the last edition of Desch's3 Metallography (1922). Gonterman's investigation, made in 1907, was the most complete one available at the time the present investigation was started. He concluded' that the system was a simple eutectiferous one and placed the eutectic at 13 per cent. antimony and 247°C. Other investigations by Tammann (1907),5 Garbow (1909),6 Rudolfi (1910),7 Loebe (1911),8 and Leroux (1913)9 added little, if any-thing, to Gonterman's diagram. A number of investigations have been made of physical properties of the alloys. The electrical conductivity of the series was studied by Matthiessen (1860)10 and by A. W. Smith (1921);" the thermoforce by Rudolfi (1910),12 and Pelabon (1923);13 the specific heat by Durrer

Jan 2, 1926

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By W. N. Lacey, R. T. Carter, B. H. Sage

The phase behavior of a number of binary systems consisting of parafin hydro-carbons has been determined in recent years. In addition, the composition of the coexisting phases of mixtures of crude oil and natural gas has been investigated.~ However, the latter study did not include information concerning the influence of the concentration of a component upon its distribution between two coexisting phases. Owing to the paucity of such information it was considered desirable to investigate in some detail the composition of the coexisting phases in the methane-propane-n-pentane system throughout the greater part of the two-phase region at a tempera-ture of 100°F. Information of this nature also permits the establishment of the critical behavior of this ternary system. Method The compositions of the coexisting phases in this ternary system at 100°F. were deter-mined by withdrawing samples from a pres-sure vessel containing a heterogeneous mixture of the three components that had been brought 10 equilibrium by mechanical agitation at the desired pressure and tem-perature. The samples were withdrawn under such conditions that the equilibrium was not disturbed and the composition of each of the phases was ascertained by means of the conventional low-temperature fractionation procedure. The apparatus employed in this investi-gation was nearly the same as that utilized in an earlier study of the methane-pentane system.~ Several minor modifica-tions in the arrangement of the apparatus were made in the interest of simplifying the procedure and avoiding the possibility of condensation in the tubing connecting the equilibrium apparatus with the analyti-cal equipment. The pressures were meas-ured by means of a pressure balance with a precision of 0.5 lb. per sq. in. It is believed that the equilibrium pressure was ascer-tained with an uncertainty of not more than 2 lb. per sq. in., even though small varia-tions in pressure obtained during the withdrawal of the samples. The tempera-ture of the equilibrium equipment was maintained by use of an automatically controlled oil bath. The bath temperature was determined by means of a copper-constantan thermocouple, the electromo-tive force being determined by means of a potentiometric circuit of such a nature as to reduce the uncertainty of the tempera ture to less than O.I f. The fractionating column employed in the determination of the composition of the gas phase had a diameter of 0.12 in. and was approximately 4 ft. long, while the column employed in the analysis of the liquid phase was 0.18 in. in diameter and about 5 ft. long. Each column was equipped with the conventional constant-volume receivers, which were maintained at a constant temperature by means of an automatically controlled oil bath. In nearly every case the distillation in thr neighborhood of the transition between

Jan 1, 1941

By Ivan E. Goodner, Charles H. Fulton

The subject of the constitution of copper-iron mattes has received considerable attention in recent years by Keller,' Belles,2 Hofman,3 and Gibb and Philp.4 Still more recently Friedrich, Röntgen, Wiedmann, Heyn and Bauer, and Leroux have published, in some instances, elaborate researches on the various systems of the sulphides, and the snlphides and their respective metals, which enter into the constitution of mattes, and have added very greatly to the knowledge of the subject. The work of Friedrich has been especially fruitful. But to' date no effort has been made to correlate the data obtained in the latter researches and apply them to the study of the product called " matte," which is made in such large quantities by copper- and lead-smelters. In this paper we propose to determine, by metallographic and chemical means, the constitution of copper-iron and copper-lead-iron mattes in the light of the recent data above mentioned. We do not discuss copper-nickel mattes or speisses (artificial arsenides). The paper is divided into three sections: I. A review and discussion of the various binary systems of the metallic sulphides, and the binary systems of various metals and their respective sulphides entering into the constitution of mattes; also a discussion of the physical properties of these sulphides. II. A description of the results obtained from the chemical and microscopic examinations of the samples of copper-iron and copper-lead-iron matte obtained from various plants.

Jan 1, 1909

By R. C. Schmidt, B. E. Kennedy

The Mont Klahoyo magnetite deposit is located about 600 km (373 miles) northwest of Abidjan, Ivory Coast. During an exploration period ending in 1977 an international joint venture group investigated the deposit and proved reserves of 670 Mt (739 million short tons) grading 36% iron. The deposit occurs at the northeast end of the Baoubly-Kiriao chain of Precambrian iron formations with associated amphibolites, pyroxenites, and gneisses of the Liberian Shield. The ore body is represented by a highly metamorphosed banded quartz-magnetite iron formation with alternating beds of iron silicates and quartz-magnetite. Amphibolite-pyroxenites and sillimanite-cordierite-garnet gneisses form hanging and footwall rocks. The iron formation has been folded into an elongated, overturned 2-shaped major drag fold with axes trending and plunging approximately northeast. Beds are vertical or dip steeply to the southeast. The ore zone has an average thickness of 130 m (427 ft) and outcrops intermittently over a distance of approximately 5.5 km (3.4 miles). Based upon detailed studies of drill cores and the results of ore dressing test work, eight stratigraphic units, identified as K- 1 to K-8, are recognizable in the iron formation. Four interbedded units are low grade silicate zones (silicate facies) while the remaining quartz-magnetite units are oxide facies, representing the important Mont Klahoyo deposit ores. Ore-bearing "K" units are subdivided further into 11 ore types, based upon their specific lithologies, iron content, and concentration characteristics. Identification of these ore types proved particularly useful to mine planning and flowsheet design. A cap of oxidized material overlies the primary quartz- magnetite iron formation, but no enrichment has occurred. It is thought that the Mont Klahoyo iron formations were deposited chemically in a volcanic environment as a siliceous iron formation with volcanism the primary source of iron and silica. Metamorphism converted the siliceous iron formation to a coarse-grained, quartz-magnetite-silicate iron formation.

Jan 1, 1983

By E. A. Gulbransen, J. W. Hickman

INTRODUCTION DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may occur to such a degree that oxides may form in the body of the film and on the outer surface which are different from those that would normally form if the additional elements were not present. The use of transmisson electron diffraction may aid us in interpreting these phenomena. Up to the present time all of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physical state of the alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the removal of carbon by oxygen in a decarburization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with

Jan 1, 1948

GENERAL COMMITTEE GERALD F. G. SHERMAN, Chairman. ARTHUR NOTMAN, Secretary. NORMAN CARMICHAEL, JOHN C. GREENWAY, W. L. CLARK, W. G. McBRIDE, B. BRITTON GOTTSBERGER, FOREST RUTHERFORD. General Committee on Transportation WALTER DOUGLAS, Chairman. CLEVELAND E. DODGE, Secretary. ARTHUR S. DWIGHT, JOHN C. GREENWAY, JULIUS KRUTTSCHNITT, JR. Committee at El Paso W. D. GORDON, ROBERT McCART, JR., W. W. ROSE. Committee at Santa Rita JOHN M. SULLY, Chairman.

Jan 12, 1916

By R. H. Winn

In this paper a heterogeneous carbonate reservoir is considered as a succession of layers of formations of radically different porosities, permeabilities, water saturations, and rock matrix types; i.e., the heterogeneity is vertical rather than radial to the wellbore. Presumably each layer is more or less homogeneous. To determine the "net oil in place" in this reservoir it is desirable to know the porosity and water saturation of each layer. In addition, the section must be subdivided into that which will produce oil, that which will produce water, and that which will produce little or nothing. In numerous wells drilled in these reservoirs radioactivity surveys, guard electrode surveys, and caliper surveys have been made. These logs have been compared with core analysis data, when available, and the analysis of the surveys compared with production data. This study, still in progress, is intended to provide improved analytical techniques if such are possible. This paper is a progress report on the work. DETERMINATION OF POROSITY The neutron-gamma log has long been recognized as a measure of hydrogen concentration.1,2,3 In reservoirs that are free of clay, shale, or other hydrogen containing matrices, it has been accepted as a measure of porosity.4,5 Empirical methods to relate relative neu-tron-gamma intensity to porosity are often employed." To provide a more precise determination of porosity from the neutron-gamma log each instrument is calibrated immediately prior to each survey by a method which refers all tools to a hydrogenous cylinder. To insure stability a calibration check is made after each survey. These calibration records are printed as an integral part of the log that is recorded in standard counts per second. A detailed description of the calibration procedure is available in the literature.' The procedure employed insures that each Survey is numerically reproducible within the limits of statistical variation. To relate the standard neutron counts per second to porosity and hole size, records were made in test wells constructed of blocks of limestone. The porosities of the blocks were accurately measured and the blocks completely saturated with fresh water. Fig. 1 presents some of the results obtained in these test wells.' The lines shown in Fig. 1 were obtained by deriving an empirical equation relating the 11 points shown so that the relationship may be projected to larger and smaller hole sizes. A detailed description of the tool is available in the literature.' Field tests indicate that the tool is adjacent to the wall of the hole most of the time when the surveys are made in uncased holes drilled with saline muds. In this circumstance porosity may be calculated from Fig. 1 if the hole size is known. When fresh muds that form thick mud cakes are employed, the centralizing effect of the mud cake must be considered and the porosity determination is less reliable. In cased holes the combined effect of variations in hole diameter and the unknown eccentricity of the casing in the hole may make porosity determinations extremely unreliable. In any event, an accurate knowledge of hole size is essen-

Jan 1, 1958

By Richard W. Smith

KYANITE, long known to occur in Georgia, did not excite commercial interest until about 1930. Investigations revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumula-tion from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not' more than a few feet. The larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersham County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habersham County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanite-mica schist belt in Habersham and Rabun counties will be discussed in this paper.

Jan 1, 1936

By A. E. J. Engel

INDUSTRIAL talcs and ground soapstones both include earth materials of different chemical and mineral compositions. In general, the industrial talcs are composed of silicates that contain appreciable amounts of magnesia. Generally talc, the mineral, is a predominant or at least common constituent. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3 (SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.11 Actually different single grains or leaves of pure talc have variations in water content ranging from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.16 Only a very small percentage of the ground industrial talcs produced in the United States approaches the composition given above (see Table 1). The purer talcs invariably occur as alteration products of magnesium carbonate rocks. Some of these relatively pure talcs include compact, massive types largely mined in California, which are designated as steatite.38,58 In general, steatites cannot contain in excess of 1.5 pct CaO, 1.5 pct combined FeO and Fe203, and 4 pct A1203. The less pure varieties of massive talc and mixtures of magnesian silicates are commonly called soapstones, or merely talc. Many industrial earth products classified as talc or as soapstone contain a variety of minerals, especially serpentine (H4Mg,Si2O9), chlorites (hydrous magnesium, iron, aluminum silicates), tremolite (Ca2Mg5H2[SiO3]8), anthophyllite ([MgCa]SiO3), diopside (CaMg[SiO3]2), and quartz (SiO2). The carbonates calcite (CaC03), dolomite (CaMg[CO3]2), and magnesite (MgCO3) are also present in some industrial talcs and soapstones. Some of these minerals, as well as sulphides, sulphates, and iron and manganese oxides, if present at all or in excess of minute amounts, may alter the composition of the industrial talc sufficiently to restrict materially its use or to lower or destroy its value. These factors are discussed in a subsequent section of this chapter.

Jan 1, 1949

By J. D. Hunt, R. J. McDonald

It is proposed that extensive fluid motion occurs between the dendrites of a Partially solid casting and it is suggested the A segregates in steel castings are a direct result of this motion. The fluid flow arises because of density differences between liquid ahead of the dendrites and the interdendritic liquid. Experiments are described on a model system investigating this fluid motion. The importance of interdendritic fluid flow is discussed with reference to longitudinal segregation. SERIOUS macro segregation is often found in large killed steel ingots. Among the most common segregates are those known as A and V, Fig. 1. The A segregates are arranged over the surface of cones, the wide parts being at the base of the ingot. The A segregates are pencil like in shape and extend from the columnar into the equiaxed region. The V segregates are distributed over inverted cones but have a less well defined shape. They occur at the center of the ingot. Because of the commercial importance of macro inhomogenities these segregates have attracted wide-scale attention. The segregates contain alloying elements and impurities which depress the freezing temperature and are thus the last liquid to freeze. A number of explanations have been proposed to explain their presence. It has been suggested1'' that the segregates are the result of the equiaxed zone growing towards the columnar region together with the interaction of convection within the bulk liquid. It has also been proposed that the segregates are the result of nucleation and rapid growth ahead of the dendritic front.3 Neither of these explanations is completely satisfactory because A segregates are pencil shaped and are not found as continuous cones. In this paper an alternative mechanism is proposed, and experiments are described on a model system to determine whether the mechanism occurs in practice. It is thought that A and V segregates are not peculiar to steels but should occur in many other large castings. Fluid motion within the bulk liquid region of a casting has been extensively discussed. Little attention has been paid to fluid motion within the partially solid regions. The work415 that has been done has been mainly concerned with the fluid motion which results from the volume contraction on freezing. The volume contraction is used to explain various types of macro segregation. The present authors suggest that in many cases the fluid flow resulting from volume contraction will be small compared with that due to other causes. When the columnar region is growing, the liquid still remaining between the dendrites has a much lower temperature near the ingot walls than at the dendrite tips. The composition of the liquid in contact with solid will vary with temperature. The density of the liquid will thus vary both because of changes in temperature and composition. The layers of different density liquid will give rise to a slow but steady liquid flow through the interdendritic regions. If there is no density change with composition, the temperature gradient within the dendritic region should give rise to a downward flow between the dendrites, shown schematically in Fig. 2. When the liquid density changes appreciably with alloy concentration this motion could either be en-

Jan 1, 1970

Schedule of Events

Jan 1, 1977

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By W. E. Forsythe

WHEN measuring ordinary temperatures, the instrument is generally placed in very close contact with the body the temperature of which is desired. However, if the temperature of the source is continually raised, a point is soon reached where no known substance will, in general, remain constant in any of its temperature-measuring properties if placed in direct contact with the source. Also, it is occasionally necessary to measure the temperature of a source that &apos;is so small or so situated that it would be very hard to bring the measuring instrument into direct contact with the source. When these conditions exist, advantage is taken of the well-known fact that all bodies, when at sufficiently high temperatures, send out radiation in amounts readily measurable. This radiation has been found to be related to the temperature. The temperatures of very hot bodies have probably always been judged by the color, or the brightness, of the light given off. With practice, one can estimate probably within 50° to 100° C. of the correct value. However, if judgment is left to the eye alone, very much larger errors are sometimes made, due to

Jan 9, 1919