Search Documents

By P. K. Currie, J. V. Walters

Solution mining of magnesium salts (Carnallite and Bischofite) is taking place near Veendam, in the northeast Netherlands. The magnesium salts are used for the production of magnesia sinter, used as a base material for the manufacture of refractory bricks for furnaces. This paper gives, first, an introduction to the operational procedure followed in Veendam, with the emphasis on some of the unique aspects, and then discusses rock-mechanical aspects of the cavity behaviour. The creep behaviour of magnesium salts is described, and Finite Element calculations on cavity stability and potential surface subsidence are discussed.

Jan 1, 1985

By AIME AIME

FEW men are better known in fuel engineering circles in the Middle West than the present Chairman of the Coal Division of the A.I.M.E. - Julian Elnathan Tobey. Now vice-president in charge of engineering of Appalachian Coals Inc., of Cincinnati, he has served that pioneer regional marketing agency since Aug. 1, 1934, when he became manager of its engineering department. His duties have included field promotion work in the interest of use of the agency's coals from eastern Kentucky and Tennessee, south western Virginia, and southern West Virginia in new plants of all types. He has been especially interested in certain industries which have shown an alarming tendency to change to natural gas or hydroelectric power; also in the development and practical application of small stokers and other mechanical equipment.

Jan 1, 1941

By GEORGE O. SUMAN

IN THE operation of oil properties there are various difficulties with pumping wells which can often be overcome or greatly lessened if sufficient attention is, directed towards pump and tubing problems. The difficulties referred to are the wearing out of pumps, sanding up of pumps, and the sanding up of the hole. As the perforations in the oil strings are large and the oil and sand loose and unconsolidated considerable trouble is often encountered in pumping wells due to the ease with which' the sand can come into the holes. DETERMINING FLUID LEVEL In determining the proper depth at which to tube a well it is essential to first find out something about the behavior of the fluid in 'the hole: Facts in regard to this natter can be obtained by finding the fluid level on pulling the tubing, by making a pumping test on the well tubed to various depths, and by bailing tests during cleaning out work. In ordinary oil field operations it is customary to take the fluid level at the time of pulling the tubing. This 'can only be done when the pump is not sanded up. There are two methods used in obtaining the fluid level. One method is to note where the outside of the tubing starts, to be covered with fluid when pulling the

Jan 1, 1925

Abbey. Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St., New York, N. Y. '21 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abeel, George H., Jr., Cons. Min. Engr 12S1, S. Canon Dr., Beverly Hills, Cal. '18 4 -Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin.. Univ. of Pittsburgh. Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 650 S. Grand Ave., Los Angeles, Cal. '82 Abele. Louis T., Min, & Met. Engr., Supt., Texas Hill Mine Coulterville, Cal. '31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada '31 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College. Pittsburg, Kan. '20 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., Member, Geological Staff of Burmah Oil Co., Ltd., Nyaunghla, Upper Burma, India. '28 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho '27 Acker, E. O'C., Met 128 East Washington Lane, Germantown, Philadelphia, Pa. '86 Ackerman, D. E., Met., Research Lab., International Nickel Co., Inc Bayonne, N: J. '24 Ackerman, George F., Engr., Real del Monte y Pachuca Min. Co., Apt. 3, Pachuca, Hgo., Mexico '29 *Acres. T. H.. Geol. Dept., Valuation & Pet. Engrg., Richfield Oil Co., 555 S. Flower St., Los Angeles, Cal. '29 Adachi, Jinzoo Address Wanted '88

Jan 1, 1934

By H. M. Chance

In the early part of 1893, I had occasion to make for the owners a professional examination of the Rich Patch tract; and, with their permission, I present in this paper, omitting the commercial portions of my report, those portions which may be valuable to future students of that region. Location, Topography And Geology. The Rich Patch tract comprises about 9000 acres, located about 3 miles west of Low Moor, on the Chesapeake and Ohio Railway, in Alleghany county, Va., and immediately adjoining the Low Moor property. In shape the tract is roughly quadrangular, being about 3 miles broad in a northerly and southerly direction, by about 6 miles long from east to West. Potts creek and Jackson river run along its northern boundary. It is drained by Hayes Gap run, Mill branch and Laurel creek, which flour north into Potts creek, and by Karnes creek, which flows northeasterly through the Low Moor property into Jackson river. The topography of the tract is shown by the accompanying map (Fig. I), and need not be described here. The valleys are cut down from 1000 to 1500 feet below the mountain summits, which generally reach an altitude of about 3000 feet above tide. The geological structure of the district is indicated by the geological cross-sections shown in Figs. 2 and 3. These sections show that the formations underlying the property extend from the Lower Silurian lin~estones up to the Devonian slates, including the numbers of the Paleozoic system of rocks as defined by the geological surveys of Virginia, Pennsylvania and New York, from No. 11. to No. VIII. • No. IX. Old Red Sandstone, No. VIII. Slates and Shales, Devoman-

Jan 1, 1900

By M. Cohen, D. J. Blickwede

Quantitative observations concerning the carbide phases in high speed steel are of importance for two general reasons: (1) the carbides, being inevitable constituents of the final structure, exert a direct influence on the properties of the steel; and (2) a substantial proportion of the total alloy content is tied-up in the carbides, and hence the extent of their solution on austenitizing governs the composition of the steel matrix. The latter relationship has a vital bearing on the response of the steel to tempering as well as on its performance in subsequent service. Accordingly, in the course of a long-term study of the behavior of high speed steels, the authors were confronted with the problem of securing quantitative data on the carbide phases. The obvious method for acquiring such information is to isolate the car-bides from the steel and subject them to chemical, X ray diffraction and other measurements. There are well-known extraction techniques which involve the chemical or electrolytic solution of the less noble matrix (ferrite, marten-site or austenite), thus leaving a residue of the carbide phases. However, the results obtained must be scrutinized carefully1,2 since the carbides may be affected by the chemical or electrolytic action. It is the purpose of the present paper to describe the experiments leading to an electrolytic-extraction technique for quantitatively isolating the carbides from both I and hardened high speed steel. Particular attention is paid to the amount, as well as the composition, of the carbides so that the matrix analysis becomes ascertainable by subtraction from the overall steel composition. Illustrative results are given for the M-2 grade of tungsten-molybdenum steel. Review of the Literature The chemical method of dissolving the matrix selectively with respect to the carbides makes use of dilute non- oxidizing reagents such as hydrochloric or sulphuric acid. Although this simple procedure has led to the determination of the cementite composition,3,4 it achieved only limited success because of the interaction between the acid and the carbide residue. Some of the carbides may not only be destroyed in this way, but the hydrogen released is likely to remove part of their carbon as hydrocarbon gases. The electrolytic technique of isolating carbides has the advantage of rapidly dissolving the specimen (anode) in the presence of less reactive solutions than are practicable with the chemical method. This reduces the possibility of chemical attack on the carbides, and furthermore, the hydrogen evolved during the electrolysis is released at the cathode which is not in close proximity to the carbides. The common electrolytes adopted for this purpose are hydrochloric and sulphuric acids.5-l1 Aqueous solutions of ferrous salts have also been used.12,13 A considerable advance in experimental technique was introduced by Treje and Benedicks14 who developed a double-compartment cell for electrolytic extraction, the anode and cathode chambers being separated by a porous diaphragm. A solution of 15 pct sodium citrate, 2 pct potassium bromide and 1 pct potassium iodide was selected for the anolyte, while the catholyte consisted of a 10 pct solution of copper sulphate, with copper serving as the cathode. This type of cell has a number of desirable characteristics: 1. The anolyte has a pH value close to 7, at least at the beginning of the run. 2. The iron that dissolves from the anode-specimen forms a water-soluble complex ion with the citrate, thereby preventing the precipitation of iron hydroxide (which would contaminate the carbide residue) despite the neutrality of the solution. 3. Copper deposition instead of hydrogen evolution occurs at the cathode, and this avoids an increasing concentration of hy-droxyl ions which (in an otherwise neutral solution) might cause the precipitation of insoluble hydroxides. 4. Contamination of the anode chamber by copper sulphate is inhibited by the porous diaphragm. Houdremont and coworkers15 applied the above method (with the further refinement of excluding oxygen during the electrolysis, washing and drying) to the extraction of carbides from a series of plain carbon steels after various heat treatments. They had quantitative success only with specimens in the annealed condition, and concluded that the size and shape of the carbide particles play an important role in the isolation process, with large spheroids exhibiting the least tendency to decompose during the electrolysis. Up to the present time, the citrate double-cell has not been used to any extent for isolating the carbides of high alloy steels, apparently on the grounds that the complex carbides are more resistant than cementite to attack in the simpler acid electrolytes. In particular, Bain and Grossmann7 and Gulyaev10.10a have employed the hydrochloric acid cell for their investigations of the carbides in high speed steel.* It will be demonstrated here that this type of cell is capable of yielding quantitative results in the case of high speed steel, and actually has certain advantages over the more complicated double cell. However, in order to provide a rigorous test of the quanti-tativeness of electrolytic procedures for the problem at hand, both methods were studied in considerable detail.

Jan 1, 1950

By C. E. Sims, H. M. Banta, S. L. Hoyt

Over the past few years, metallic arc welding has been extended to steels of the hardenable type. As compared with other methods of fabrication, production has been facilitated, service performance frequently has been improved, and the overall results have been so favorable that engineers and production men have placed great emphasis on this application of welding. The metallurgist and welding engineer, however, have been confronted with new problems, since, for one reason, the harder steels are more apt to crack and special precautions must be taken if sound joints are to be procured. Some of the factors that are pertinent to this problem are metallurgical, and it is an object of this contribution to discuss steel manufacture and processing methods and to show how their control assists in reducing the hazard of cracking. By this time, the problem of cracking— specifically underbead cracking, or "hard cracks," or parent-metal cracks-—is well known, and a large amount of work has been published, both here and abroad, dealing with this subject.' The tests described are made under restraint to facilitate cracking and arc so designed that a semiquantitative, or at least a relative, value of the cracking tendency is obtained. As one would expect, it has been reported that the incidence of cracking increases with the carbon and alloy content of the steel. More specifically, the cracking tendency is said to increase with the hardenability of the steel, though it is now recognized that the situation is not so simple. The phenomenon itself, on the other hand, has been but loosely described, and it is in only broad generalizations that this cracking has been related to steel metallurgy. Thus, while it has been abundantly demonstrated that the hardenable aircraft steel, S.A.E. 4130, must tend to crack when are-welded, the problem still remains of why two lots of the same composition and the same hardenability can vary so greatly in cracking tendency, or what it is about the prior metallurgical history that so strongly affects the results. Further, while the efficacy of preheating and postheating in preventing cracking is recognized and utilized in production, the mechanism by which they function seems not to have been described. These points are thought to be significant in the production of steel for fabrication by metallic arc welding and, hence, of interest to mill and process metallurgists and welding engineers. Consequently, it is another object of this paper to discuss the mechanism of parent-metal cracking, including the influence of the condition of the steel and the control of cracking by manipulation of the time-temperature conditions during and after welding. A new method of rating the cracking tendency is also discussed, and the results of the test are related to steel composition and structure or prior history. The work to be described was the outgrowth of work in 1940-41 at Battelle Memorial Institutc on two projects, one

Jan 1, 1945

By E. C. Harder

AT a Meeting of the New York Section, on May 23, 1918, the sole subject of discussion was the nature and occurrence of iron ores in certain parts of the world.? Owing to the importance of this subject, it has been deemed' advisable to publish the remarks made at that meeting in the form of a paper, for presentation at the Milwaukee Meeting, instead of in the usual place, under News of Local Sections. The remarks related to the following districts: Brazil, by E. C. Harder, of the U. S. Geological Survey; Scandinavia, by Waldemar Lindgren, of the U. S. Geological Survey; Cuba, by C. M. Weld, of the U. S. Bureau 'of Mines; Southern Europe, by A. C. Spencer, of the U. S. Geological Survey; China, by H. Foster Bain, of the U. S. Bureau of Mines; Alsace-Lorraine, by Sidney Paige, of the U. S. Geological Survey. BRAZIL By E. C. Harder During the years immediately preceding the war, the iron ores of Brazil were attracting the attention of iron operators both in Europe and in the United States. This was clue to the large quantities of practically undeveloped ore available, and to its great purity. It is reasonably safe to state that had capital not been diverted from the exploitation of these deposits to war purposes, Brazilian iron ores would probably now be offered in European and American markets. It is certain that after the war these ores will play a prominent part in the economic reconstruction of Europe and perhaps in the development of America.

Jan 9, 1918

By Freeman Bishop

Mercury is the latest ecological disaster. It was believed to be no pollution problem because it is heavier than water and expected to fall to the bottom of streams. But the Food and Drug Administration (FDA) found that mercury in a dozen states and several Canadian provinces was being ingested by fish. A Deadly Dose First to sound the alarm was Canada when a graduate student's research revealed that mercury contamination in Lake St. Clair had reached 1.4 pmm. which is almost three times the 0.5 ppm the FDA's allowable maximum.

Jan 1, 1970

The surface area that mining requires is a minuscule fraction of the total land mass of the United States, according to the US Bureau of Mines' latest report "Land Utilization and Reclamation in the Mining Industry, 1930-71." During the 42-year period from 1930 to 1971, the mining industry utilized 3.65 million acres-only 0.16% of a total 2.27 billion acres of land-and reclaimed 1.46 mil- lion acres, or 40% of what it used. Which leaves, as still unreclaimed, 0.096% of the nation's total land mass.

Jan 10, 1974

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1975

By B. H. Caudle, L. G. Davies, I. H. Silberberg

This paper presents a method of predicting the recovery and performance of a five-spot steam injection project, in which a realistic approach to pattern sweepout efficiencies is made. Published methods for radial systems were modified for the five-spot pattern by approximating the stream lines with straight lines radiating from the injection well and then converging to the producing well. In each radial segment, the position of the steam front and the temperature profile ahead of the steam front were determined by heat balance equations, which included an estimation of heat losses to surrounding formations. The location of the saturations behind the cold water front was determined from a Buckley-Leverett solution to the material balance equation. Results from this program show steamflood recovery in a five-spot pattern to be considerably less than that predicted for true linear or radial flow systems. For a specific reservoir containing 900-cp oil, a steamflood in a purely radial flow system was predicted to recover more than 75 percent of the original oil in place when 2 PV of water had been injected as steam. A five-spot steamflood with otherwise identical properties was predicted to recover 10 percent of the original oil in place when 0.15 PV of water had been injected as steam and to recover almost no oil thereafter. A cold water five-spot flood in this system was predicted to recover approximately W percent of the oil in place with I PV of water injected. For a five-spot pattern in an example reservoir with 10-cp oil, steam injection similarly showed lower ultimate recovery than water injection but no improvement in recovery rule. Introduction The thermal recovery method considered in this study is steam injection in a five-spot pattern. Pattern steam injection has been given little attention in the past, possibly because of some rather obvious disadvantages. Unless steam temperature is maintained throughout the entire swept area, the process will revert to simple waterflood with all heat being lost prior to reaching the oil bank. Also, the oil viscosity reduction takes place near the steam front and not around the producing wellbore, so that low producing rates must still be endured. This is the reason for the success of the steam stimulation, or cyclic injection, in which the fluids are produced from the same well used for injection. On the other hand, steamflooding can offer some advantages. Oil displacement is by four methods: (1) mechanical displacement by the condensed water, (2) viscosity reduction of the crude oil, (3) swelling of the crude oil, and (4) distillation of the crude oil in the steam zone. Although dependent upon the crude, laboratory experiments have shown displacements up to 80 percent by steamflooding. In addition, steam is a good heat transport medium, since it is cheap and has a high heat content. Previous Investigations Previous publications have reported methods for predicting recovery in a steamflood for linear and radial systems. Since no pattern sweep efficiency is taken into consideration, the recovery even from a radial system must be greater than from more realistic geometries such as the very common five-spot patterns. Probably the broadest coverage is given by Willman who reported experimental results and offered a method of predicting recovery for a radial flow system. They concluded that both hot water and steam injection recover more oil than an ordinary waterflood, and that steam injection could yield recoveries "as much as 100 percent greater than by water flood." They also concluded that both the heat requirements for a reservoir and the residual oil remaining in the reservoir after steam injection were independent of the amount of oil originally in place, that short exploitation times were desirable, and that a high percentage of net sand in the reservoir with a high initial oil saturation was desirable. The method assumes that the flood occurs in three concentric cylindrical zones: (1) an inner steam zone, (2) a central hot water zone, and (3) an outer cold waterflood zone. Displacement in the steam zone is based on laboratory-determined residual oil saturations while the hot water and cold water zones use the conventional Buckley-Leverett equations. Although the results shown by Willman et al. are for a radial system flowing out from the well to an assumed external circular boundary, their equations did

Jan 1, 1969

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.' It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this' paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Albert Brokaw

THE so-called ?paraffin dirt" of the Gulf Coast oil fields has been con¬sidered an indication of the possible presence of oil and gas, and not a few wells have been brought in solely on the basis of such evidence. In a sense, it may be empirically justified as evidence of the presence of oil or gas, though it cannot be said to be infallible. If the writer is correctly informed, its association with oil and gas was pointed out by Lee Hager some years ago, and while it is commonly mentioned by geologists and operators in conversation, no discussion seems to have found its way into print. The present interpretation is based on laboratory study rather than on field investigation, and is put forth with the hope of stimulating discussion which shall lead to more complete understanding. The term "paraffin dirt" has been applied to soils with a peculiar texture, which has been described' as "curdy" or "rubbery." When moist, the material breaks much after the fashion of "green" cheese. It is rubbery under compression, but does not resemble rubber in tenacity or cohesion. When dry, the material ranges from hard clods to a horny mass of high tensile strength. The shrinkage in drying is very great, especially in the hornlike matter. The moist material ranges in color from dark brown in the specimens rich in organic matter to grayish in specimens containing more inorganic matter. All of the specimens studied were readily attacked by molds, which in some cases grew in great profusion on the samples. Samples exhibited a rather characteristic "swampy" or "mucky" odor when wet, and a characteristic odor of humic soils when moist.

Jan 4, 1918

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By John E. Latz

QUICKSAND far below the surface, stopped two attempts by the Potash Co. of America to sink a third shaft to a potash bed that lies 1000 ft below the southern New Mexico desert. Virtually all methods of grouting were employed in the two failures without any indication of consolidation of the flowing sand. Sinking the South Shaft at the Carlsbad potash mine seemed an almost insurmountable task, until freezing was employed as a final resort. This process that proved to be the answer may be defined as "the sinking of a shaft by freezing, consists of the formation, in the water-bearing strata, of a large block of frozen ground in which it is possible to sink a shaft without danger of an influx of water, providing the ice-wall between the water outside and the shaft itself is strong enough to resist the hydrostatic pressure." Freezing Method Used Extensively in Europe Successful frozen ground shaft sinking projects had been completed in Europe, and Russel G. Haworth, resident manager of the Potash Co. of America, went abroad in search of the know-how needed for the New Mexico undertaking. The freezing process, with a history of two failures at the time, was first successfully employed by Poetsch in 1885 at the Houssu Collieries near Haine St. Pierre, Belgium. Poetsch contracted to sink the remaining 64 ft of an uncompleted shaft through water laden strata from a depth of 190 ft to a depth of 254 ft. This work was in progress until 1887. The freezing and sinking consumed more than two years. As a result of early failures, the process was not favorably received until soon after the turn of the century. The accurate prediction of success in a given application was made possible by the concerted effort and study of a group of European engineers. Means of accurate deviation measurement and control were devised, the nature and properties of frozen water laden soil (the ice wall) were investigated, a thorough and rational basis of refrigeration load calculation developed, and concurrently the efficiency and dependability of refrigeration machinery was greatly advanced. Numerous shafts in Germany, Belgium, France, and England today testify to the reliability and economical surety of the freezing method. Applied to the South Shaft, which is circular in cross-section and 15-ft diam, the freezing method consisted of drilling holes 350-ft deep, through the water bearing strata into impervious ground-the freeze hole pattern being concentric with the shaft and 31-ft diam. The holes were cased with pipe closed on the bottom end. Smaller tubes were placed inside these casings and connected to a header supplying chilled brine from a refrigeration plant. The brine descended in the tubing to the bottom of the hole and ascended through the annular space between the two pipes to the top of the casing; flowed into the return header and back to the refrigeration plant. Under these conditions, each of the freeze hole casings became surrounded by a cylinder of ice

Jan 1, 1952

By Frederick Prime

The Great or Cumberland Valley, which (under a variety of names) extends from Canada, through Vermont, Massachusetts, Connecticut, New York, Pennsylvania, Maryland, Virginia, and East Tennessee, to Alabama, is composed in part of limestones lying immediately above the Potsdam sandstone. Geologically, they belong to the era between the Potsdam and Trenton, and are commonly termed Calciferous. A peculiarity of these limestones is their great richness in limonite or brown hematite ores, which form a large part of the charges of the many blast-furnaces situated on their outcrops. The mines from which the ores are obtained are (properly speaking) only pits or quarries, from which 'the ore is extracted by means of picks or shovels, powder being rarely employed. The ore does not occur casually at any point in the limestone, but forms regular lines, following apparently the outcrops of certain beds. In Lehigh County, Penn., where 1 have been engaged on the Geological Survey of the State, during the past season, there are three or four of these lines. During the progress of the survey I was much struck by the fact that the two most important and promising lines of outcrop were, one at the base of the crystalline schists (forming the South or Lehigh Mountain), and overlying the Potsdam sandstone conformably; the other, near the line of junction of the calciferous limestone with the slates of the Cincinnati epoch. The mines along these two lines, following the topography of the country, were in place, richer and more permanent than those of the belts between, which were generally leaner. A peculiarity of these two lines of outcrop, and one to which I particularly desire to draw attention, is the occurrence of what I at first mistook for a highly altered slaty limestone, but which subsequent analysis proved to consist in great part of damourite (hydrated potash mica). The following are analyses of this damourite slate: I. From Fogelsville, Lehigh County, within a few hundred feet of the contact of limestone and slate, by Dr. F. A. Genth. 11. From Hensingerville, Lehigh County, within 300 feet of gneiss, by Mr. Sydney Castle, of the University of Pennsylvania. 111. From Allentown, Lehigh County, within 150 feet of con