Search Documents

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.'" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By D. J. Mack, R. E. Reiswig

Six examples of the peritectoid transformation were selected from the literature and studied by the method of isothermal transformation. The kinetics and mechanisms of five of the examples are presented as TTT diagrams and photomicrographs. The exist-enc- of a peritectoid in the sixth case is doubtful. ALTHOUGH the peritectoid transformation per se has been known for many years, no precise published data exist concerning the kinetics or mechanisms involved in transformations of this type, except for the brief treatment by Rhines, et al. 1,10 Bearing in mind the fact that investigations of recent years are uncovering more and more peritectoids and suspected peritectoids, a thorough study of the well-established peritectoids appeared to be in order. It was for this reason that a study of the kinetics and morphological mechanisms of six binary peritectoids was undertaken. The six peritectoids selected from the literature for study were those reported at 7.02 wt pct Al-Ag, 26.0 wt pct Sb-Cu, 30.5 wt pct Sb-Cu, 32.3 wt pct Sn-Cu, 8.35 wt pct Si-Cu, and 21.2 wt pct Al-Cu. These selections were based on availability and purity of components, ease of preparation and heat-treatment, and estimated reliability of the available equilibrium diagrams in the regions of interest. EXPERIMENTAL PROCEDURE The alloys used in this investigation were induction melted in electrode-grade graphite and chill-cast in cast-iron split molds. In all cases, the alloys were so brittle that they could easily be broken into samples weighing 1 or 2 g. Chemical analyses showed that the alloys used were close to the respective peritectoid compositions reported in the literature and that the impurity levels were low in all cases. Metallographic examination showed uniform distributions of phases in all samples, indicating uniformity of composition in the samples studied. Isothermal transformation studies were carried out in fused-salt media, using the familiar inter-rupted-quench method. Uniformity of temperature in the salt baths was maintained by continuous stirring with a stainless-steel agitator. On the basis of actual observations of the temperature fluctuations, the estimated temperature control was + 10C for the Ag-Al and Cu-Sb alloys and ±30C for the Cu-Sn, Cu-Si, and Cu-Al alloys. The accuracy of all temperature measurements was estimated to be ±1°C. It was found necessary to mount metallographic specimens of the Ag-Al alloy in cold-curing methyl methacrylate, since the temperatures encountered in mounting in bakelite or lucite caused an appreciable degree of transformation to the ß phase. For the other alloys, wood-flour-filled bakelite mounts were used to avoid extraneous X-ray diffraction lines during the later examination of the metallographic specimens on a Norelco Geiger-counter d if f r ac tomete r. In the X-ray diffraction procedure, agreement between the published diffraction patterns and those obtained in this study was good. This was particularly important for phase identification, since the literature contained little in the way of micrograph description in some cases. Etching of the silver-aluminum alloy for metallographic examination was done by swabbing with either of the following reagents: 1) 10 g CrO3, 1 g (NH4), SO2, 0.5 g NH4NO3, 100 ml H2O, or 2) 10 ml NH4OH, 1 ml 20 pct KOH, 4 ml 3 pct H2O2, 5 ml H2O. The other alloys were etched with the usual bichromate etchant: 2 g K2Cr2O7, 1.5 g NaC1, 8 ml conc. H2SO4, 100 ml H20 (swabbed vigorously). EXPERIMENTAL RESULTS A) The Ag-Al peritectoid at 7.02 wt pct Al— The phase equilibrium involved in this peritectoid is shown in Fig. I.2 The phase boundaries in the vicinity of the peritectoid were most comprehensively established by Hume-Rothery, et al,3 who placed the equilibrium temperature at 448 °C and the equilibrium compositions of the a ß' and y phases at 6.11, 7.02, and 7.24 wt pct Al, respective The alloy used in this study analyzed4 6.95 wt pct A making it slightly hypoperitectoid according to the accepted equilibrium diagram. The rate of the transformation a+ y — ß' varies rapidly with degree of undercooling below the equilibrium temperature, passing through a maximum in the vicinity of 350°C. Thus the TTT dia-

Jan 1, 1960

By W. A. Tiller, W. C. Johnston

A high-temperature electromagnetic stirrer is described in which heating and stirring are accomplished by independently controlled power sources. The appavatus is suitable lor use at temperatures up to 1700°C in a variety of ambient atmospheres. Some typical examples of the homogenizatimz capabilities of the system are given. THERE are few processes in solidification that are not markedly affected by motion in the melt during freezing. In many instances, the mechanisms are diffusion-controlled, and the transport in the melt may be greatly accelerated by deliberately stirring the melt. In zone-refining, stirring1 assists the removal of rejected impurities from the interface, so the process proceeds at a faster rate. The transition from a planar to a cellular interface is caused by constitutional undercooling in the melt ahead of the interface: and stirring delays its onset. Stirring is valuable for homogenization of melts: and chemical reaction with sluggish kinetics may be accelerated. Finally, it has been observed that grain refinement is related to motion in the melt. Fine grain castings are usually produced by the addition of catalysts to the -melt,' catalysts which are thought to act simply as hetereogeneous nucleation centers. Even here motion is important. Richards and Rostoker 5 applied ultrasonic vibration to a solidifying A1-Cu alloy which had been innoculated with a catalyst and found that the grain diameter fell linearly with the amplitude, the peak acceleration and the power input to the melt from the transducer. Finally, mechanical and electrical stirring alone have been used to generate a fine-grained structure.6,7 Johnston ef a1.' have carried out a series of systematic investigations of grain refinement by electromagnetic stirring in a number of low melting point alloys. They found, for example, that the number of grains per unit volume in Pb-Sn alloys could be increased several orders of magnitude by stirring an undercooled melt at the moment of recalescence. In general, a relation AT .H = constant prevailed for a given grain size, where AT was the undercooling of the melt and H the field strength. In more recent work, deliberate homogeneous nucleation of slightly undercooled melts established that the mechanism of refinement must be one involving crystal fragmentation and subsequent multiplication, rather than a "shower" of nuclei effect.9 It is the purpose of this note to describe a stirring device suitable for use up to 1700°C. At low temperatures mechanical stirring and direct-current methods are feasible, but at high temperatures the problem of a protective atmosphere and of electrode corrosion rules out such procedures. The most convenient method for high temperatures is to use externally generated ac fields for both stirring and heating. With rf induction heating alone, considerable stirring and agitation can be achieved, but in general the penetration of field into the melt is small, and the stirring cannot be controlled independently of the heating. In the present experiments, separate power sources of different frequencies for heating and for stirring were used. A susceptor design was chosen so that the 450 kc rf heating field was completely absorbed in the susceptor. The stirring frequency, 400 cps, hereafter called the af field, was chosen so that a high penetration of the melt proper was achieved. EXPERIMENTAL APPARATUS The apparatus, Fig. 1, consists of a quartz tube and end plates, surrounded by an rf induction coil and six equally spaced af stirring coils, four of which are shown in full and a fifth in section. Each af stirring coil is a transformer of which the secondary is a single-turn water-cooled copper loop and the primary is composed of two 10 amp-117 v Variac cores as shown. These cores are cooled by forced air, as each of the six pairs will carry maximum currents of 15 amp for short periods. Each set of Variac windings are connected in series, but opposite sets are connected in parallel with a three-phase 400 cps 400-v source. By properly phasing the coils in this way, a rotating field is produced. Capacitors C1, C2, and C3 in Fig. 2 are used to match this inductive load to the generator. Fig. 3 shows a cutaway view of the quartz tube. The sample (1 in. diam by 1 in. high) is placed in a tapered alumina crucible. An axial W-26 pct Re thermocouple, enclosed by a protection tube, is provided. The cruci-

Jan 1, 1968

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-' cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967

"NAME…""Utah"" is derived from the name of the Indian tribe, variously spelled ""Yuta, “Ute"" ""Youta,"" ""Uta,"" ""Eutaw,"" and finally ""Utah."" It means ""in the tops of the mountains,"" or ""on the heights."" The state emblem is the ""Beehive,"" typical of industry. State nickname is ""Beehive State.""AREA…Utah is the tenth state in area. It contains 84,990 square miles, of which 2,806 miles are water. When admitted as a territory in 1850, Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.TOPOGRAPHY…Utah is generally mountainous, with several main ranges and also detached groups of mountains. The valleys are broad and level. The mean altitude of the state is 6,100 feet above sea level, which makes the state the third highest of the Union. The highest point in Utah is King's Peak (13,498) in the Uinta range. The lowest point is Beaverdam Creek (2,000) in Washington county.CLIMATE…The climate is diversified between mild temperate in the northern portion to semitropical in the southern portion. There are four distinct seasons. Snowfall is heavy at the greater altitudes and rare in the southern portion. Rainfall is moderate throughout the state. Extremes of heat and cold are unusual."

Jan 1, 1925

Between July 10 and August 15, 1918, the Secretary of United Engineering Society, of Engineering Foundation, and of Engineering Council visited 17 cities which are headquarters for large numbers of engineers. His mission was to tell men in all branches of the profession about "Centralized Activities of National Engineering Societies." Stops were made at Denver, Salt Lake City, Reno, San Francisco, Sacramento, Portland, Seattle, Spokane, Anaconda, Butte, Duluth,

Jan 10, 1918

By W. F. Wheeler

IN the study of the coals of Illinois now being carried on by the State Geological Survey, an attempt is being made to determine the most satisfactory basis of comparison between different coals. The following discussion is based upon work done for the survey in the laboratories of the State University and under the general direction of Prof. S. W. Parr. " Pure coal " has been defined by Mr. A. Bement1 as ash- and moisture-free coal, and the use of this " pure coal " as a basis for comparing different bituminous coals has lately been much discussed among engineers in the middle West. By some the B.t.u. of the pure coal is being used to check calorimetric results, and to calculate the calorific value of different coal-samples from the same seam, for which purposes it is necessary to assume-first, that the composition and calorific value of pure coal from different parts of the same coal-seam are uniform, and, second, that these values remain constant after the coal is mined, both of which assumptions there are reasons to believe are inconsistent with the facts. Certain variables are included in pure coal, as ordinarily defined, and disregard of them may lead to serious error. In any event, where delicate shades of difference are involved, no sure interpretation of results can be made, unless these variables be eliminated. As a basis of comparison between coals, ash- and moisture-free coal is much to be preferred to " dry coal," and still more is it to be preferred to " moist coal," as ordinarily reported in analyses. There are, however, two constituents other than ash and moisture which are similar in effect to them, and which

Jan 1, 1908

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent;, a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928

By David Scott

THE MOGOLLON mining district, New Mexico, has received little public attention, although for 15 years it has been the leading silver producer of the state; it is situated in a region remote from the principal lines of travel, and its activities have usually been limited to the operations of two or three companies. The value of the total production of the district in the 44 years of its history has been estimated at $15,000,000. For the years 1904 to 1917, inclusive, the output was: gold, $4,370,000; silver, 10,042,000 oz.; copper, 874,862 lb.; total value, approximately. $10,500,000. In 1913 the district contributed 80 per cent. of the total silver production of New Mexico, but in 1917 only 41 per cent., due to serious interruption in the operations of the leading producer. Since 1914 the silver output has diminished one-half, and the present high value of silver is nearly offset by the increase in cost of production. The output of gold has rarely exceeded 35 per cent, of the total for New Mexico. The ratio of silver to gold, by weight, has averaged 46:1 based on the whole output of the district. LOCATION AND TOPOGRAPHY The town of Mogollon is 75 mi. (121 km.) by a poorly located highway from the nearest railroad terminals, at Silver City and Tyrone. All supplies are transported by motor trucks and teams. The area, sometimes called the Cooney Mining District, lies on the western flank of the Mogollon Mountains, which occupy the western part of Socorro County. The elevations drop steeply on the west to the valley of the San Francisco River, adjacent to the Arizona boundary. The topography is very rugged, the whole area being sharply dissected; deep canyons with steep gradients and rugged walls are characteristic of the whole western-slope of the Mogollon Range. The main canyons run east and west, and usually maintain a flow of water during the entire year. As would be expected in a region of such deep dissection, the

Jan 2, 1920

By M. S. Klima, P. T. Luckie

Interfacing new or improved unit operations SUBMODULES with the EXECUTIVE of a macro analysis simulator usually requires modification of the input data. For example, particle processing SUBMODULES that are sufficiently general in nature to provide useful predictions require input data for rather narrow size fractions. Such data is not always available for the EXECUTIVE and must therefore be generated by the SUBMODULE. A successful interface to allow incorporation of a new SUBMODULE for comminution and one for classification in a general stream state flowsheet simulator is presented. The general nature of the SUBMODULES, as well as the logic of expanding and contracting the required data input is discussed.

Jan 1, 1983

By W. F. Boericke, T. H. Garnett

The Wisconsin zinc district, or the Upper Mississippi lead and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies country in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, withroads, railways, streams, and the various towns, or "camps," around which the mines are clustered. The hatchwork indicates the areas in which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zoncs of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. ease or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within comparatively recent time been worked intensively for zinc, the chances are good for opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However; the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Ben-ton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland. The district is one of the best farming districts in Wisconsin, with deep fertile soil. The farms are large and well improved, and the towns are modern and prosperous. Railroad facilities are good and proximity to Chicago is an asset. Mining is usually done on a leasing system of 10

Jan 1, 1920

By W. F., Netzeband

SEVERAL criteria have been used more or less successfully in finding and developing orebodies in this district. Among them is the relation of the fracture to the orebodies. It has been known for some time that there was some relation, but it has been but recently. that careful study has been given to this subject. Like all the criteria used in this district, this relationship must be used with caution, for what-is true in one part of the district is not necessarily true in another.

Jan 1, 1928

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties situated at 29 West 39th Street in New York City United Engineering Trustees, Inc. When Mr Carnegie made his gift, "for the erection of a suitable union home" for the engineering societies, United Engineering Trustees, Inc (then United Engineering Society) was chartered un¬der Chapter 703, Laws of the State of New York, 1904, for "the advancement of the engineering arts and sciences in all their branches, and to maintain a free public engineering library " The Corporation was further empowered to acquire real and personal property and to use, maintain and occupy it, with the provision that any building erected by the Corporation shall be used perpet¬ually as a meeting place and headquar¬ters for the Founder Societies Thus the Carnegie gift realized the ideal of bring¬ing the engineering societies together under one roof, and the Corporation through its members nominated in equal numbers by the four Founder Societies had the necessary authority to act for the Founder Societies in their joint in¬terests in owning and operating for them not only Engineering Societies Building, but in the course of time, Engineering Societies Library, and The Engineering

Jan 1, 1952

An informal discussion on the application of physical chemistry to steelmaking was held during the Annual Meeting of the Institute in February, 1929. Alexander L. Feild presided. In opening the session, Mr. Feild said: We are all familiar with the cooperative mining and metallurgical studies that were begun in 1920 by the U. S. Bureau of Mines, the Carnegie Institute of Technology, and the Mining and Metallurgical Advisory Boards, and in particular with the work on the physical chemistry of steelmaking which was launched under the technical direction of Dr. C. H. Herty, Jr., in May, 1926. It was this work at Pittsburgh more than anything else that was the immediate cause of the formation within the Institute of a committee on the physical chemistry of steelmaking. During the latter part of 1927 a small group of Institute members interested in. the general subject of the physical chemistry of steelmaking undertook the organization of a subcommittee within the Iron and Steel Committee, to foster an active interest in this comparatively new field among the Institute membership and to obtain papers for publication in the Transactions, covering the various phases of the general subject. This plan was conceived by C. E. Meissner, to whose active efforts at the outset as well as during the past year is largely due whatever measure of success the plan has thus far attained. The subcommittee, now a committee of the Iron and Steel Division, was recognized and formally made a part of the Institute's organization at the February, 1928, meeting. As originally organized and as const,it,uted during the past year the committee has been made up as follows: C. H. Herty, Jr., C. D. King, A. B. Kinzel, John Johnston, C. E. Meissner, L. F. Reinartz, R. B. Sosman, and A. L. Feild, Chairman. Dr. C. H. Herty, Jr. has just been elected chairman for the coming year and C. E. Meissner has been reelected as secretary. From the outset it has been the settled policy of the committee to make membership an annual rather than a permanent matter and to reconstitute in part the membership of the committee each year by dropping a certain number of members and adding new members. In view of the fact that the work of the committee is still in a

Jan 1, 1929

GENTLEMAN: The year 1928 was another in the history of the Institute which was marked by quiet growth and steady progress. The total membership as of December 31, 1928, was 8703 as compared with 8438 on December 31, in 1927. Again the main increase has been in Members and the number of Junior Associates is less. As will be seen also by the Treasurer's report, the increase is reflected in larger receipts for dues indicating that fewer have had to be dropped for non-payment. There has been a gratifying increase in the number applying for reinstatement and it seems clear that interest in and attachment to the Institute has notably increased. The year was signalized by the merging of the Rocky Mountain Club with the Institute which brought to our roll one hundred and forty who were not previously members from among the men who have made the West. It also brought to the Institute a strong tradition of good fellowship and a fund of over $100,000, the interest from which is to be expended so far as may be, for purposes beneficial to the Western states. The Endowment Committee expects to see other and similar funds entrusted to the Institute and the Board has already appointed a special committee to consider all projects for expenditure of the revenue from them. It is felt that with the organization and personnel available in the Institute even modest revenues can be made to yield large returns in the way of scientific and technical knowledge. Within the year also, a third great Division has been organized within the Institute, building on the foundation of the old Iron and Steel Committee. The new Division signalized its independence by joining the Lake Superior Mining Institute in a visit to the Menominee Range in September and by furnishing material for a special volume of 353 pages, "Iron and Steel" Technology in 1928," printed and distributed in December. The Institute of Metals Division held its fall meeting with good attendance as one feature of National Metal Week at Philadelphia in October, and published its volume of Proceedings, running to 836 pages, in August. "Petroleum Development and Technology in 1927," 844 pages, came out in June and recorded the work of the Petroleum Division. A most interesting Fall meeting was also held by the Division at Tulsa,

Jan 1, 1929

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period August 1, 1916 to September 10, 1916: C. L. Cantley, New Glasgow, N. S. H. M. La Follette, La Follette, Tenn. D. A. Cowell, Columbus, Ohio. Montrose L. Lee, Montevideo, Uruguay. Alexander Deussen, Houston, Texas. V. H. McNutt, Billings, Mont. Chas. E. Dutton, Goldfield, Nev. J. W. Maller, New York, N. Y. H. S. Emlaw, Grand Haven, Mich. Edwin W. Mills, Tul. Mi Chung, Chosen, J. M. Gillette, Swatsburg, N. Y. Korea. E. Gorilla, San Antonio, Texas. Francis R. Pine, Elizabeth N. J. Bertram Grant, Kingman, Arizona. Frank A. Ray, Columbus, Ohio. Ruger W. Hay, Bisbee, Arizona. John A. Rice, El Paso, Texas. C. F. Hendricks, Cobalt, Ontario. W. E. Rice, Ringwood Manor, N. J. Stanley C. Herold, San Jose, Cal. W. H. Staver, Lynchburg, Va. Lloyd Hoffman, Pottersville, N. J. Ralph H. Sweetser, Easton, Pa. Charles Hunter, London, England. Kirby Thomas, New York, N. Y. G. Jansen, Benkoelen, Sumatra. Henry Traphagen, Union Hill. T. H. Jenks, Oatman, Arizona. M. M. Valerius, Tulsa, Okla. Warren jenny, Chanaral, Chile. Wilfrid B. Wainewright, London, Eng. Walter A. Barrows, Jr., of Brainerd, Minn., has been elected president and general manager of the Thomas Iron Co., Easton, Pa., to succeed Ralph H. Sweetser, whose resignation of several months ago becomes

Jan 10, 1916

By Pierre R. Hines

These notes are based on observations made while on a recent trip through the West, for the purpose of studying the practical operation of the ball-mill. The writer takes this opportunity to express his thanks for courtesies extended at the many plants visited as well as for the valuable data received: While there are several types of ball-mill on the market, particular attention will here be given to the diaphragm type, as the open-trunnion type, especially the conical mill, has been thoroughly discussed in the Transactions. There is a prevailing impression that the ball-mill is a recent development; however, ball-mills were used extensively in Montana and other western states for crushing ores for concentration as far back as 1808. Its present prominence is due in part to its recent successful application by one of the large copper companies. Without any reference to dry grinding, the first successful ball-mill for wet crushing, which is still in operation, was built 10 years ago.l This mill, designed by Erminio Ferraris for crushing Sardinian ores for concentration, is of more than passing interest. It embodies the peripheral discharge with grates, large forged-steel balls, and the principal features of the modern ball-mill. The results approach present-day practice, the chief differences being that the mechanical construction has been improved in the modern types. Crushing Action of Ball-mill The action of the balls and the principles of crushing have been studied by several investigators.2 Their conclusions are confirmed by results obtained by the writer in experimenting with a small machine built at

Jan 1, 1918

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Project Manager or Construction Engineer, 48, married. Twenty-five years' experience on mine, mill and smelter construction work, design and operation, U. S. and Mexico. Speak Spanish. Now employed; available 30 days notice. Prefer U. S. or Mexico. M-698-489-E-1-San Francisco. Mining Geologist, 53, single. Eleven years' intensive field experience giving a completely practical competence for the smallest or largest of areas; plus the highest possible grade of academic background and independent research qualifying for top rating. Available in thirty days or less. Any location acceptable. M-699-3611-E-7-San Francisco.

Jan 1, 1952

By James Douglas

I had the good fortune to visit the Stockholm Exposition just before its close in October last, and to get a glimpse of the methods used in Sweden in making the wonderful steel and iron for which its furnaces are so famous. My time and opportunities for observation were limited, but some points which I noted may be worth bringing to the notice of the Institute. The Exposition itself was confined to the natural and artificial products of Scanclinavia, and therefore iron and steel held a very prominent place in it. There was a complete collection of the rocks and ores of the Peninsula made by the Geological Survey; and every iron-mine of note exhibited a glass model of its workings, as well as classified specimens, accompaniecl by thorough analyses of the ores. Another feature of interest was the display of models of the old mining-machinery, in the invention and introduction of which Sweden led the way, and of the old and new surveying-instruments and compasses devised for the exploration of the Swedish iron-ore bodies, all of which are more or less magnetic. The magnetometric collection and exhibit of methods of operation made by Prof. Nordestrijm were supremely instructive. The larger metallurgical works, such as those of the Kopparberg and Sandvik companies, exhibited their wares in separate pavilions, in which crude and manufactured objects were arranged most eflectively and tastefully; while the smaller companies erected in the Industrial Arts Building trophies, every one of which was an object of beauty. One was struck on all sides by the fine asthetic feeling exhibited in the ingenious installation of materials and objects not easily lending themselves to artistic treatment. Hammers, picks and drill-steel were grouped into mural designs which it was a delight to look at.

Jan 1, 1899

By Thomas V. Falkie

The use of operation research and computer techniques in the mineral industries continued to gain acceptance during 1966. There are generally at least five sources of information for researchers and practitioners in the field: (1) Technical periodicals like MINING ENGINEER- ING, Mining Congress Journal, etc. (2) Proceedings of the Symposium and Short Course on Computers and Operations Re- search in Mineral Industries, held last year at Penn. State University and jointly sponsored by the University of Arizona, Stanford University, Colorado School of Mines, Penn. State University and the Society of Mining Engineers of AIME. (3) Various local conferences, such as the 1966 Rocky Mountain Minerals Conference held in Denver. (4) United States Bureau of Mines publications. (5) The AIME annual meeting in New York and the SME Fall Meeting in Tampa.

Jan 2, 1967