Search Documents

By M. P. Meehan

The purpose of this paper is to present the key elements in a system; study of the electrical system for a timing and/or tilling operation. The ability of an electrical system to function in a reliable fashion at its proper levels is essential for an operation to be successful. A system study consists of a load study for determining the capability of the electrical network to provide power to the various loads and a short circuit study for determining the capability of the electrical protective equipment to properly protect against fault conditions. The sequence of events in a system study is data acquisition, determining the electrical parameters and analyzing the ability of the system to meet these requirements. If the system is small, herd calculations will be the manner in which the study will be conducted; if it is large then commuters will be used. A load study has as its objectives the determination of the capability and reliability of the source of power, transformers and conductors to satisfactorily deliver power to the loads at an acceptable voltage level. The Information required is a single line diagram showing the source, transformers, conductors and loads.

Jan 1, 1980

By Robert F. Shurtz

This paper suggests that pre-occupation with the random process model notised by geostatisticians may result in neglect of more promising techniques, especially since the random process model does not appear to be essential to current geostatistical procedures. This point of view is emphasized pictorially. To emphasize the potential of new techniques a simple application of the conventional Brownian function is described. The probabilities estimated in this truly random way are different from those estimated by Kriging

Jan 1, 1980

By Philip E. LaMoreaux

The development of large quantities of ground water for any major use in an area is always of environmental concern to representatives of regulatory groups, citizens, agricultural and industrial users. From these concerns, state and federal congressional representatives receive a variety of impulses from their constituents and in turn begin a series of questions upon which to-base appropriate legislative actions. The kaolin industry in Georgia is substantial to the economy and the welfare of an important segment of east-central Georgia. It uses large quantities of water for processing. This constitutes an important source of income and tax revenue. Pumping test procedures to provide an accurate and efficient dewatering scheme have been developed and carried out at a number of mines in the kaolin district of Georgia. This paper highlights one such test and is directed at an assessment of the impact of this industry on ground water supplies of an area.

Jan 1, 1983

By John D. Smith

This paper describes how a knowledge of inherent rock characteristics can aid the mining engineer in his design of a mining method for a massive domelike structure. The paper shows how the pertinent rock characteristics were measured and analyzed and how the data obtained was used for design purposes. This analysis was conducted in 1964 in a producing salt dome, since that time, mine management has tried certain of the recommendations for mine design changes. The results of such changes are presented.

Jan 1, 1968

By R. Asmatulu

According to Darcy?s law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By N. Magdalinovic

Generally speaking, erosion, as a process which entails degradation of surface layers of earth under the influence of the mechanical energy of surface waters, and from the point of view of biosphere sustainability, is a harmful process. This is absolutely true when agricultural and forest areas are concerned. However, if erosion is viewed selectively, this general definition about its harm raises serious questions. In other words, the erosion which takes place in the terrains where there is no vegetation because of the geological composition of the soil, does no harm. On the contrary, if the mineralogical composition of such terrains is characterized by a presence of precious and rare metals, erosion can be very useful. It contributes to the creation of new alluvial deposits of these metals in the waters in the plain land. It is here that torrents from hills come down and cause erosion. And finally, if there were no erosion, there would be no renewable deposits of gravel and sand.

Jan 1, 2007

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the Separation Efficiency: ES = (R ? Rg) where R is the percentage of the valuable constituent and Rg the percentage of the waste appearing in the concentrate. The Separation Efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products.

Jan 1, 1969

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By E. R. Phelps

It is very seldom that a completely new project is initiated. Most projects consist of a new and different combination of proven techniques or a combination of proven and new techniques. The theme of my discussion today falls in the second category. Proven methods of water transportation and proven methods of bulk material handling were combined with some new techniques which resulted in a new market for the coal industry and a cheaper fuel supply for the power industry. In this respect I refer to the water transportation of coal from the West Kentucky coal fields to coal burning power plants on the west coast of Florida. Peabody Coal Company, Florida Power Company, Gulf Coast Transit, and Mid-South Towing combined their individual requirements and "know how' to make this project possible. I feel the results speak for themselves since it proves that coal can be mined in the West Kentucky coal fields, transported some 1,200 miles by river barge and some 450 miles by ocean going barges, be delivered to power plants on the west coast of Florida and still meet the competitive prices of gas and residual oil. The unique parts of this project concerns the storage and trans loading facilities for coal from river equipment to ocean equipment near New Orleans; the return haul of phosphate and it's trans loading from ocean to river equipment at the same facility and the use of large ocean going barges. In detail it works as follows: Coal is mined in West Kentucky and loaded into 1,500 ton river barges on the Green River. It is then transported some 100 miles to the mouth of the Green on the Ohio River, then 200 miles down the Ohio to it's convergence with the Mississippi, and then 900 miles down the Mississippi to the trans loading facility some 40 miles South of New Orleans. There it is transferred from the 1,500 ton river barges to 18,000 ton ocean going barges and hauled some 450 miles across the Gulf of Mexico to the Gannon Station of Tampa Electric at Tampa entailing a total haul of approximately 1,650 miles.

Jan 1, 1966

By Gordon B. French

The Occidental Oil Shale mining and retorting system for the production of shale oil has many advantages over the conventional underground mine and surface retort systems. For example only a portion of the oil shale is mined and transported to the outside, where it blends with the existing shale talus found on most of the slopes in the immediate area. The retorted spent shale is retained underground so that it does not become a surface disposal problem. The process consumes only minor amounts of water which is produced in adequate amounts in the retorting to fulfill all mining operations needs without outside supplies. Noise and dust levels are kept to a minimum with most of the facilities located underground. The exception being the generating stations and facilities as required to monitor air and water qualities, and last but not least, more than four times as much oil is pro¬duced from a given acre than from conventional surface processing. With the increased thicknesses as available on the government monopoly area this number could be increased by a substantial amount.

Jan 1, 1975

By D. S. Dinsmoor

Boron, estimated to comprise about 0.001 percent of the earth's crust (Fleischer 10), as an element is never found free in nature, although its compounds are found in many localities. the borates are the most important. Sassolite (B(OH)3) and boracite (Mg6C12B1406), non-borates, are-of-minor importance. The crystal structures of most natural borates are still unknown. A classification based solely on the ratio of boron to the total number of cations has been devised (Palache 28). This classification divides the borates into four, sub-groups; anhydrous borates, hydrated borates, borates containing hydroxyl or halogen and compound borates. Only four or five minerals of the hydrated borates group have ever been used commercially. In more recent years, the sodium borates have comprised all but a 'small fraction of all borates used. Borax, the hydrated borate compound, is the most important of all boron compounds. It has been used so long and so often that the layman often confuses borax and boron and, applies the terms synonymously.

Jan 1, 1958

By L. Alagha, F. Schott, M. B. Haya, Z. Xiao, K. C. Monyake

"Froth flotation is a process in which valuable minerals are separated from gangue minerals on the basis of surface wettabilities. It is a universally accepted process for the beneficiation of coal. The large amount of coal fines that have been generated from both mining and beneficiation processes has been reported as a chronic problem to both fine coal preparation and utilization as these fines contain a high amount of ash forming minerals. The current study investigated the potential application of Synthetic Bio-compatible Polymers as slime depressants in fine coal flotation for the possibility to enhance the combustible recovery and ash rejection. Raw coal samples containing 21% of ash-forming minerals were crushed, grinded and floated in the presence of Chitosan polymer. Flotation tests were carried out in D-12 Denver flotation cell with 1-Liter capacity. Flotation outcomes were studied as a function of polymer concentration. Box-Behnken factorial method was used for experimental design. Second order response functions were produced for ash% and combustible recovery. The results obtained from this study demonstrated positive influence of chitosan polymer on ash% and combustible recovery. Ash % was decreased by 3.32 % while an increase of 48.15 % in combustible recovery was observed when chitosan was introduced in the flotation process. INTRODUCTION Froth flotation is a widely used method of separating minerals by utilizing the difference between surface wettabilities [1], [2].Modern mechanized mining and ore handling operations produce large amounts of coal fines which in the past were not processed but discarded as waste[3]. Even though flotation is the best method of beneficiation for coal, it can be challenging in case of fine coals. In fine coals, slime coatings of colloidal mineral matter exist on the coal surface. These coatings render the coal hydrophilic, hence reducing flotation efficiency and recovery. Of late, different researches have been using biodegradable polymers to determine their feasibility in enhancing fine coal flotation efficiency[4].Naturally occurring and synthetic polymers, for example, polyacrylamide-based polymers, have been widely used in flotation as multifunctional reagents[5],[6],[7]. Hybrid polyacrylamide polymer has been successfully used as a depressant for ash forming minerals in fine coal flotation[3]. Recently, chitosan has been successfully used in flocculating quartz particles to produce faster settling rates of fine tailings [4]."

Jan 1, 2018

By Ande&apos, Bengt n

The first Model 480 SALA-HGMS R carousel high gradient magnetic separator was recently manufactured (Figure 1). The carousel's design was based upon the high gradient magnetic separation technology developed and owned by Sala Magnetics Incorporated, Cambridge, Massachusetts. After a short (approximately 300 hours) in-house mechanical and electrical test and break-in period, the carousel was ready for a long term demonstration test. This paper describes the demonstration plant and operational performance of the Model 480 HGMS treating a low grade iron ore tailings. A location convenient to Sala International's main office in Sala, Sweden was desirable because Sala engineers and technicians were to operate the demonstration plant. The Strassa iron ore mine in central Sweden was chosen because it fit most of the criteria that was important for a good demonstration site. The Strassa mine is part of the state owned Svenskt Stal AB. The mine produces about 320,000 tons of iron concentrate per year consisting of 200,000 tons of magnitite concentrate and 120,000 tons of hematite concentrate.

Jan 1, 1980

By R. A. Seitz

Although the role of the collector has long been thought to play a predominant role in coal flotation, recent investigations by the authors show that the frother plays an equally important role. These investigations have included extensive testwork in several coal preparation plants and in the laboratory. The factors which were investigated include the absolute level of collector and frother addition, the ratio of frother to collector additions, the type of frother, and the particle size distribution of the feed. Results from this testwork reveal strong interactions between these factors as well as the necessity of considering these factors in order to optimize the reagent regime.

Jan 1, 1987

Factors which cause thiourea consumption in gold-leaching systems include adsorption by gangue mineral particles, complexation with base metal ions, thermal degradation, and oxidation by air/ferric iron. Of these factors oxidation by ferric iron is the most significant factor. Of course, ferric sulfate is desired as an oxidant for the gold leaching reaction, but an excess of ferric sulfate leads to high thiourea consumption. In this regard, the rate of gold leaching by thiourea must be balanced against the rate of thiourea decomposition. It is important to note that the thiourea decomposition reaction in ferric sulfate solution is relatively slow in pure solutions and has been found to be first order with respect to both thiourea concentration and total ferric iron concentration. However, when mineral particles from gold-bearing ores or concentrates are present, the decomposition rate can become quite significant. As might be expected, the catalytic activity of mineral surfaces varies with particle composition and size. Experimental results are discussed with respect to the consumption of thiourea.

Jan 1, 1997

By O. E. Wheeler

The term "finite element analysis" is heard and seen in print a great deal these days; a few words on what precisely it is are in order. In the broadest sense, finite element analysis is an application of an idea developed by a nineteenth century mathematician named Rayleigh. His basic idea was to decompose any problem in mathematical physics into a large number of simpler problems, solve the simpler problems, and then put those solutions together to form an approximation to the solution of the original problem. The scheme works nicely because of two features: first, much of the difficulty in solving practical problems of mathematical physics stems from irregularities in the boundaries and the simpler problems can be chosen with regular boundaries and second the smaller problems are solved for small physical areas where simple approximations of the solution do not differ much from the true solution. In the narrower sense, in which we are now interested, finite element analysis is a technique of using imaginary simple structural elements to construct analytical models of real structures. A direct parallel with the Rayleigh approach exists since the "finite elements" have simple boundaries and are restricted to simple behavior within a single element. Although the correspondence between Rayleigh's ideas and finite element analysis is now widely recognized, the computational tool, as it has developed over the last thirty years, comes not from the discipline of physics but rather from that of structural engineering. It is interesting that it came not from the traditional research community, the universities, but instead from working

Jan 1, 1974

By William G. Doepken

The extensive use of rubber-tired support vehicles as a complement to a fleet of load-haul-dump and drill jumbo units has proved invaluable in maintaining scheduled multilevel/multiheading development drifting advances at the Henderson Mine. Support equipment, whether self-powered or towed, releases primary drill-blast-muck equipment from the supportive functions of ground control, utilities installation, steel and concrete construction and supply handling, thus providing both balance and increased flexibility to an underground, rubber-tired mining system. Experience has indicated that increases in man productivity and improved safety and working conditions coupled with decreases in overall costs and mining cycle times are realized with the inclusion of support vehicles in the mining fleet.

Jan 1, 1976

By V. Iordachita

In the beginning of the third millennium, the world mining industry has to cope with many challenges; the continuous need for mineral resource deposits and the mostly unsolved economic efforts should be accompanied with ecologic measures mankind has to take in order to avoid self-destruction. The present paper analyses the possibilities of using underground mining spaces in Romania for storing dangerous waste and suggests viable solutions. The characteristics of dangerous wastes and their disposal in suitable underground spaces are analyzed. Also, some methods for deactivating dangerous solid wastes as well as the importance of monitoring underground spaces in order to eliminate environmental impact risks are presented.

Jan 1, 2008

By Arthur S. Radtke

The structural setting of disseminated-replacement gold deposits of the Carlin-type and other aspects of their genesis are closely related to events which took place during the evolution of the Basin and Range province. The deposits formed as a result. of chemical and physical processes which took place at shallow depths in the roots of hot spring systems at moderate temperatures (about 200°C) and low pressures (about 25 bars) (Radtke and Dickson, 1974). Locations of Carlin-type gold deposits in the Basin and Range province are shown in Figure 1. Most of the block-faulted mountain ranges in the Great Basin formed by tectonic activity that happened since Miocene time, although faulting in some places probably began in Eocene to Oligocene time (Hamilton and Myers, 1966). The Carlin-type deposits are spatially related to Basin and Range-type faults: Many deposits, such as Getchell, Pinson, Preble, and Cortez, occur along the flanks of ranges, while other deposits, including Carlin (Radtke, 1974) occur within the ranges in areas characterized by crosscutting and intersecting high-angle or Basin and Range-type faults. The association of the ore deposits with Basin and Range-type faults is evidence that ore deposition is young, Miocene or later. The steep, high-angle faults played three roles: first, they provided deep channels for upward-flowing solutions; second, in preparing the rocks for fluid penetration by brecciation and general rock dislocation; and third, they moved sedimentary carbonate rocks, favorable for ore deposition, from deep levels to near-surface positions where the physico-chemical conditions were more suitable for the deposition of ore.

Jan 1, 1976

By R. G. Lundquist

The idea that fragmentation for mineral processing results from some tradeoff between increased drilling and blasting and increased load on the primary crusher is well known. In a previous paper (Lundquist and Konya, 1963) the authors reported on the results of a laboratory scale study which attempted to quantify this tradeoff in energy terms. If we look only at the production of new surface area, blasting is 1700 times as energy efficient as crushing. On an energy cost basis, crushing is 57 times as expensive per unit surface produced as blasting with dynamite and more than 700 times as expensive as blasting with ANFO. The comminution process at an open pit operation starts with the drilling of blast holes and ends after the material has gone through the fine grind circuit. Operators usually break the process into several separate operations and do their cost analysis based on this approach. Often drilling and blasting is considered as one system and crushing and grinding are considered as one or two separate and independent systems. Operators will independently optimize each system. The cost for the drilling and blasting system is obvious in operations which use contract drillers to do the drilling and either contract the blasting to a distributor or do the blasting themselves. The cost of rock breaking in this manner is readily available since the contract driller will supply a monthly drilling cost to the operation and either the distributor who is contracting the blasting or the distributor who is supplying the powder to the blasting operation will also supply a monthly billing. In either case, the costs can easily be seen on a monthly or per ton basis. They are not difficult to compute even when drilling and blasting are done entirely in-house.

Jan 1, 1985