Search Documents

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By Tom Plouf, Deepak Malhotra

INTRODUCTION The U. S. mining industry experienced a severe recession in the early 1980's. This resulted in the realization that the domestic mining industry had to compete on a global basis and only the strong or the low-cost producers would survive. The economic viability of a mining company not only depended on maximizing mineral recovery but also on its ability to do so at minimum cost. Companies had to become more productive not only by cutting costs, but also by developing and/or evaluating new technologies in existing or new plants. Several innovative concepts, including in-pit crushing and conveying, fine crushing, improved classification equipment, flotation, column flotation, pressure filtration, etc., have been developed in recent years. This paper addresses the impact of new flotation concepts and equipment on mill design. MILL DESIGN PHILOSOPHY Modern mill design, especially for large capacity plants, has its foundation in minimizing capital and operating costs. Capital costs can be minimized by minimizing the various components of the capital cost: infrastructure, equipment, instrumentation, structural, initial spare parts costs, etc. All these costs are minimized by simplifying the mill design and/or process flowsheet. The simplified process flowsheet, where applicable, consists of a single stage primary crusher followed by a semiautogeneous - ball mill grinding circuit to produce feed for a flotation circuit. Multiple flotation circuits have been eliminated in most cases. These concepts minimize the cost and encourage the use of large capacity equipment while maintaining optimum metallurgical recovery. The philosophy of mill modernization/modification is generally driven by the desire to increase the mill capacity within the limits of the existing mill building. This need is facilitated by using large size flotation equipment and eliminating multiple parallel flotation circuits in order to minimize capital and operating costs. Conventional flotation machine development has paralleled this mill design philosophy. FLOTATION CELL DESIGN Since froth flotation has been the most widely used separation process for over half a century, one would expect that it would be possible to design and select flotation machines for specific applications based on scientific principles. But this has not been the case. Best judgment, experience and personal prejudice have played a key role in equipment selection. These factors, along with the difficulty of evaluating new concepts in commercial plants, has slowed progress in implementation and commercialization of innovative ideas and/or equipment. Conventional Flotation There have been no major technological advances in conventional flotation cell design in recent years. A recent flotation cell survey indicates that 'larger flotation cells are still the order of the day.”(1) A comprehensive review of design of flotation machines indicate that they have been mechanically redesigned and are generally simpler and easier to maintain and less expensive to manufacture. (2,3) The approximate chronological development of conventional cells from the 25 cubic foot cells to the 3000 cubic foot cells, which were recently installed at the Copperton concentrator of Utah Copper, is given in Table 1. Larger flotation cells are the obvious choice for new plants or plants looking for expansion because of the following reasons: • They have lower capital cost per unit volume • Installation costs are generally lower because fewer units require less space • Maintenance costs are lower because of fewer mechanisms • Power requirements (HP/ton dry feed) are generally lower • with increased flotation cell size as illustrated in Table 2 [Table 1. Conventional Flotation Cell Size Development Year Individual Cubic Cell Size, Feet 1925 25 1935 50 1960 100 1965 300 1970 500 1975 1,000 1980 1,500 1985 3,000]

Jan 1, 1989

By F. Gonzalez, A. Zambrano, J. Schwoebel, S. Kravits

Significant lost time delays were experienced by Carbonifera de Nueva Rosita, S.A. de C.V. ("CNR") during mining development of the Pasta de Conchos Mine ("the Mine") near Nueva Rosita, Coahuila, Mexico. Furthermore, methane gas concentration in the return air course had exceeded 1.0 percent. Resource Enterprises, Inc. ("REI") was contracted by CNR to recommend an approach to reduce methane emissions at the Mine. In order to recommend a degasification approach, REI and CNR obtained geologic and reservoir characteristics of the Double coal seam, Olmos Formation. A vertical core hole was drilled to obtain core samples to determine gas content (average 8.4 cm3/gm) and to conduct a slug test to estimate permeability (34 md). This information was used to simulate gas productivity and drainage effectiveness. The simulation indicated that underground horizontal boreholes would remove significant quantities of gas in advance of mining in a reasonable period of time. Based on the results of the simulation study, an underground degasification drilling program was initiated at the Mine. In a six month period, five long in-mine degasification boreholes were drilled in advance of CNR's three to five years mining projections. Peak gas production from the five boreholes (approximately 2,750 cumulative meters) had exceeded 45,000 m3/D. Results to date have indicated a general reduction in methane concentration in the return air course below 0.8 percent.

Jan 1, 1993

By John K. Adams

Phosphorus may be incorporated into sedimentary rocks in at least four different ways: (1) by the accumulation of detrital mineral fragments, (2) by the accumulation of phosphatic organic debris, (3) by diagenesis and (4) perhaps by the primary precipitation of calcium phosphate. Based-on the petrographic examination of Cretaceous and Tertiary sediments from the northern and central parts of the Atlantic Coastal Plain, Diagenesis is the most important of these mechanisms. Both syndiagenesis and epidiagenesis are required to explain the origin of all the diagenetic phosphate mineral species which occur in the northern and central parts of the coastal plain. Syndiagenesis produced much of the coastal plain's apatite. It was operative below the sediment-water interface while the substrate was being compacted. Compaction forced pore waters, which were enriched in phosphate by the decomposition of organic matter, upward through calcareous sediments. The PO43- radicle replaced the CO23- and calcareous nodules, pellets and shell fragments were converted to apatite. Epidiagenetic reactions occurred in the subaerial environment where downward percolating meteoric waters carried phosphate in solution to cites where cation activity was sufficiently high to form new minerals. Vivianite may form where ferrous iron is available and wavellite and variscite may form in the presence of aluminum rich minerals. Textural evidence suggests that many of the reactions were repeated. The present day appearance of apatite, vivianite, wavellite and variscite in the coastal plain may represent several generations of diagenesis.

Jan 1, 1972

By W. Blake, J. Mahaut, W. Hustrulid

Division II at Kamoto mine in Kolwezi, Zaire represents a transition zone between Divisions I and III where transverse and longitudinal cut-and-fill rooms were being mined. Because this transition zone had been geologically depicted as being badly faulted the mining in this division had been deferred to a future time. However, to increase production and to reduce mining costs by carrying out the mining of the 3 divisions simultaneously, it was decided to mine Division II. The mining research group of Gecamines was given the task of designing a mining geometry then testing this design in a full scale test. Based on an evaluation of the faulting and fracturing of the 2 parallel orebodies and on an extensive in situ testing program preliminary mathematical analyses were used to develop and evaluate room and pillar designs in the 35°-65° dipping bedded formations. Based on these analyses and the constraints of having to fit the design of Division II to grade into Divisions I and III in a logical manner, a mining geometry for Division II evolved. To test this design an instrumented room was excavated in the most critical area. The results of this full scale testing showed that the behavior of the roof and wall rocks were as had been predicted by finite element computer model studies which incorporated the material properties and results of the field testing. The room geometry design was both judged and observed to be stable, hence mining commenced.

Jan 1, 1977

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of both underground and surface operations. The East Ertsberg Skarn System (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production is from the third lift (Deep Ore Zone), which is scheduled to peak at 80,000 mtpd during 2009, with this rate sustained through 2015. The orebody is proven below the existing caving level, with the next vertical block called the Deep Mill Level Zone (DMLZ). This paper presents an overview of the DMLZ Mine based on recent feasibility level study. The mine is being designed for a peak production rate of 29.2 million mtpy, with 1,803 total ore draw points spread over a panel caving footprint of about 1.3km by 375m. The present reserves for this mine total 501 million tonnes. Located 1,400-1,800m below the original surface, the DMLZ will be one of the deepest caving operations in the world. Production is scheduled to commence in 2015. Discussion is provided on most design aspects including; caving methodology and layouts, geotechnical predictions and risks, ore handling systems, ventilation design and associated infrastructure, high-lift pumping system, cost estimation and expenditure scheduling.

Jan 1, 2010

By K. A. Smith, X. Cheng

Introduction The separation of minerals from complex sulfide ores by flotation requires careful control of the surface chemical behaviors of the minerals constituting the ores. When the minerals in the ore are finely disseminated, extremely fine grinding is needed to liberate the minerals. Fine grinding is not only an energy-intensive operation, but also influences the flotation behaviors of liberated minerals. Steel balls are commonly used for grinding. Galvanic interactions occur not only between sulfide minerals and grinding media but also among the different sulfide minerals themselves. The electrochemical characteristics of chalcopyrite and pyrrhotite when they are independently coupled with steel grinding media and the relevance of these characteristics to the flotation behavior of these minerals have been exten¬sively studied (Cheng and Iwasaki, 1992: Li and Iwasaki, 1992). These studies dealt with reactions in two electrode combinations, simulating mineral-grinding medium and mineral-mineral interactions. In practice, however, it is more common to involve more than one sulfide mineral. In a study of a pyrite-pyrrhotite-mild steel system, Pozzo et al. (1989) provided evidence that a mineral having an intermediate potential could behave differently, depending on the condi¬tion of galvanic contact. This investigation was undertaken to study a chalcopyrite-pyrrhotite-mild steel system to gain better in¬sight into the mechanism of multiple galvanic interactions. A three-electrode system was chosen to simulate a typical copper sulfide ore. The sulfide minerals were represented by chalcopyrite and pyrrhotite. The grinding medium was rep¬resented by mild steel. The nature of galvanic interactions involving these minerals and grinding medium in an oxygen atmosphere was investigated in a three-electrode combina¬tion, and an attempt was made to relate the laboratory flotation results of pyrrhotite-chalcopyrite ores. Possible implications to the differential flotation of complex sulfide ores are discussed. Key words: Electrochemistry, Flotation, Sulfide ores Experimental The pyrrhotite (57.74% Fe, 0.09% Cu, 4.84% Ni and 36.54% S) sample was obtained from Falconbridge Ltd.'s Strathcona mine, Ontario, Canada, and the chalcopyrite (26.00% Cu, 28.57% Fe, 0.05% Ni and 31.52% S) sample came from Transvaal, South Africa. Mild steel (AISI 1020, 0.2% C) was chosen to represent grinding media. A conventional three-electrode cell was used in the elec¬trochemical measurements. The working, counter and refer¬ence electrodes were, respectively, sulfide minerals or mild steel, graphite rod and saturated calomel electrode (SCE, 0.245 V vs. standard hydrogen electrode). The exposed areas of the sulfide minerals and grinding medium electrodes were approximately the same (0.17 to 0.19 cm2). The preparation methods of working electrodes, the reagents used, the experi¬mental procedures and the instrumentation were the same as those described previously (Cheng and Iwasaki, 1992). Rest potentials of pyrrhotite, chalcopyrite and mild steel were measured individually in 0.05-M sodium sulfate solu¬tions. Combination potentials and galvanic currents of the sulfide minerals and grinding medium were measured in short-circuited two- and three-electrode systems. All poten¬tials in this study are quoted in volts with respect to the standard hydrogen electrode (SHE). To simulate the constantly abrading conditions in a ball mill, rest potentials, combination potentials and galvanic currents were also measured by rotating a porcelain ball against chalcopyrite, pyrrhotite and mild steel electrodes in

Jan 1, 2000

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By H. G. Naidu, Raj K. Singhai, S. P. Singh

Introduction The economics of open-pit mining de¬pend heavily on the cost of overburden removal. It is necessary to maintain a pit slope as steep as possible. Steeper slopes lower the volume of overburden to be handled, thus lower the cost of material handling. There is, however, a limit to which the pit slopes in any given situation can be steepened. Steepening beyond this point could jeopardize the pitwall stability, ren¬dering it unsafe. It might even result in curtailment of pit production. Several factors affect the stability of pitwalls. Some are natural, such as topogra¬phy and regional and local geology. Others are man made, such as pit geometry, ground water management, equipment, drilling and blasting, and the type of excavation. Greater control can be exercised in the latter with proper planning and by following a set of procedures based on field experiences. This article deals with one such control¬lable factor - drilling and blasting. The eco¬nomics of steeper pit slopes is discussed, followed by a record of drilling and blasting practices in western Canadian surface mines. Microprocessor-based instrumentation and its application to blasthole drilling is also described. Economics of steeper pit slopes The economics of steeper pit slopes is not a new issue. It should be reinforced, though, that pit slopes must be as steep as possible to ensure maximum recovery of minerals at a minimum stripping ratio. For operating, economic, and safety reasons, different pit slopes are maintained during different phases of pit development. Figure 1 shows a hypothetical ore body, cylindrical shape, with a radius of 225 m (740 ft) and located 30 m (100 ft) beneath the surface. The mining operations are planned at two different slope angles of 25° and 40°. The ultimate pit depth was established on the basis of the criterion of "break even pit." The variation of the stripping ratio at differ¬ent mine levels is shown in Fig. 2. Table I summarizes the eco¬nomics involved for two pit slopes, 25° and 40°. Figure 3 presents the profits during the life of the mine for these two pit slopes. This study shows that steeper slopes for an open pit operation are far more advanta¬geous than flatter slopes. But, what is the optimum slope at any one point in the life of a moving pit? And how can the stable slopes be maintained over the short- and long-term? Canadian blasting practices A survey of blasting practices in western Canadian surface coal mines revealed that, at most mines, hard consolidated overburden is drilled and blasted. Blastholes are drilled with rotary crawler-¬mounted rigs using bits in the 220 to 310 mm-diam (8.5 to 12 in.-diam) range. Typi¬cal hole depths are 12 to 18 m (40 to 60 ft) to accommodate the pit bench heights of 12 to 15 m (40 to 50 ft). For a 12-m (40-ft) high bench, a typical hole will be 14.6 m (48 ft) deep including the subgrade drilling of 2.6 m (8.5 ft). Half of this hole will typically be a powder column and half will be stemmed. For a 15-m (50-ft) bench, a typical hole will be up to 18 m (66 ft) deep including the subgrade drilling. Drilling patterns are usually 9 m (29.5 ft) spacing and 9 m (29.5 ft) burden. De¬pending on local geology and hole diameter selected, drilling patterns of 8 x 8 m, 8.5 x 7.3 m, and staggered patterns of 11 x 5.5 m

Jan 1, 1989

By Jerome F. Sheldon

The earliest recorded history in the use of belt conveyors in the United States is in O. Evans' "Miller's Guide" published in Philadelphia in 1795. Evans defines a conveyor as a "broad endless strap of thin pliant leather or canvas revolving over two pulleys in a case or trough." (Ref. 1) In this definition, pulleys are being used in a bulk material belt conveyor application. Pulleys used in belt drives can trace their origin back to 1200 A.D. In fact, Engineers had considerable experience designing them into drives transmitting greater horsepower than those used in the early belt conveyors. In belt conveyor application, a pulley's purpose is primarily three-fold, 1) support the belt in directional changes, as designed in the conveyor, 2) transmit driving power to the belt, and 3) guide or train the belt. There are various types of pulleys used in belt conveyor systems and these are thoroughly covered in "Belt Conveyors For Bulk Materials" prepared by CEMA, 1966. For our discussion, however, the most common used in belt conveyors are drive pulleys, snub pulleys, head pulleys, tail pulleys, takeup pulleys and bend pulleys. The drive pulley imparts the driving force to the belt and may be located at the head or discharge end of the conveyor, in return strand, or at the tailor loading end of the conveyor. A snub pulley is located near the drive pulley to provide more arc of contact between the belt and pulley for maximum

Jan 1, 1971

By Leonard Sugin

Recent changes in the field of ore and bulk commodity handling has forced a reevaluation of previously conceived notions. When vessels were small, and sources of raw material were reasonably close to areas of need, the role of the shipping terminal was of secondary importance. Now terminals must be built to take advantage of the economic benefits of the supercarriers. The shipping rates of the 80's will not be determined by the 60,000 DWT or even 150,000 ton capacity bulk carrier, but rather by the supercarriers in the 250,000 DWT class or larger. When the Suez Canal was closed, the shipping industry took a hard look at the economics of the large bulk carrier. Naval architects overcame the problems and successfully designed large supertankers, which today are plying the seas in excess of 350,000 DWT. Orders have been placed for tankers of 480,000 DWT. The shippers of dry bulk materials are now coming to similar conclusions about the economics of supercarriers. As of today, over 40 orders have been placed for vessels in the 250,000 DWT class, representing an investment of over 11/2 billion dollars, and many more are being considered. These vessels are being designed as combination ore/oil (0/0) or ore/bulk/oil (OBO's) carriers. The oil industry has seen the need for terminals which can accommodate these supertankers. The dry bulk shippers, and particularly ore shippers, must now act.

Jan 1, 1972

By John Nadolski

Intensive hydrologic monitoring of the Powder river basin has been on-going since the early 1970's. Data were used in environ- mental assessments and for determination of hydrologic consequences associated with coal mining activities. For most coal mine operators, data collection has continued in this baseline mode with little or no statistical analysis of the data and with no statistical procedure established to detect changes in groundwater quality. For the past four years Powder River Coal Company has studied several statistical techniques to analyze groundwater quality. Three objectives were pursued: 1) to determine the baseline water quality for key aquifers; 2) to determine which wells could be deleted from the monitoring program without reducing monitoring effectiveness; and 3) to define a statistical test to determine water quality changes. Knowledge of the regional geo-hydrologic system was combined with an analysis of the water quality monitoring in order to identify homogeneous aquifer zones. All wells within an aquifer zone were treated as one population, and a t-test was used to determine the minimum number of samples needed to define the water quality for each aquifer zone. Results indicate that the data for each aquifer zone were nor- mally distributed and that groundwater quality could be defined using a fairly small number of samples. Because of the minimum sample size test, groundwater quality sampling was reduced by between 75 and 85 percent.

Jan 1, 1989

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal's mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

By Herschel H. Potter

While preparing this paper, I soon realized I had a problem in defining what injuries should be classified as "personal." Admittedly, in some cases, falls of persons, sprains and strains, pulling and pushing injuries, and back injuries may have been caused by the individual. But, I believe the number of injuries directly attributed to an individual's carelessness is relatively small in comparison to the total number of injuries in those categories. For discussion purposes, the injuries most often considered to be personal, that is, caused by individuals are those classified as back injuries. My paper will be devoted to back injuries because this category represents the greatest number of injuries occurring in coal mining. A man's best friends are his wife, his back, and his dog. The back, however, has a reputation of not being as faithful as his other two friends.1 "Industrial back injury is one of the major occupational health problems plaguing industry to- day. According to national surveys, back injury accounts for more lost time than any other occupational injury and costs companies thousands of dollars in compensation, medical fees and over- time pay."2 A study conducted by USA Today found that back ailments afflict an estimated 75 million Americans, have totally disabled about 2.5 million adults, lead to as many as 200,000 required surgeries each year, are a leading cause of absenteeism and disability, are the second leading cause of hospitalization, are responsible for 18 million doctor visits a year and cost about 93 million work-days annually. The cost to industry is estimated at $14 billion a year.3 During the past 30 years, a great deal of accident prevention education has been directed toward the reduction of back injuries. However, this effort has not produced any great change in the incidence of the injury. Back injuries should be of the utmost concern to everyone here today. I don't need to tell you what the incidence rate is for back injuries, nor will I use any statistics to inform you of the incidence rate for the coal mine industry or any specific mine. It is only important to know that the number of back injuries is excessive. Back in- juries resulting from lifting have been and continue to be one of the most constant and undiminishing problems in the occupational environment. The fact is, we use our backs to per- form work that the back was not designed to do. Historically, manual materials handling related accidents have consistently accounted for the largest percentage of all industrial accidents. In fact, over 25 percent of all industrial accidents are related to handling of materials.4 In underground coal mining operations, material handling accidents account for even larger percentage of lost time injuries. In 1983, for example, they accounted for 34 percent of all lost time injuries and 32.6 percent of all non-lost time injuries. 5 I want to use one example of a task that will illustrate what I have just said: the building of a concrete block stopping. Each solid concrete block will weigh from 60 to 70 pounds. To build a stop- ping 6 feet high and 20 feet wide will take approximately 80 blocks. On the average, these 80 blocks will be handled at least four times from loading into the conveyance for transportation to being placed while constructing the stopping. This generally requires repetitive lifting from ground level. The next three slides demonstrate the lifts

Jan 1, 1986

By E. W. Geist

This paper is presented from the viewpoint of the mill operator and maintenance supervisor. Its purpose is to highlight the things that have been accomplished by the mill designers to lighten the load for the maintenance superintendent and to reduce the overall costs for the plant operator. The complexity of plant design, the civil and structural engineering problems encountered when the satisfactory maintenance layout is accomplished are appreciated, and the writer is fully aware of the complexities of these problems. However, it is not the purpose of this particular paper to dwell upon these problems, nor to emphasize or de-emphasize the problems of the civil, mechanical and electrical engineers. It is simply that the paper will attempt to review what these people have accomplished in spite of the many technical problems. This paper then is prepared with the operator and maintenance people?s viewpoint. What is their definition of design for maintenance? It is the writer's interpretation that the various design concepts which mean improved maintenance are such items as (I) maintenance areas, (2) laydown space for maintenance materials in specific maintenance jobs, (3) the inclusion of bridge cranes in the plant and specific design of the craneways to accomplish flexibilities for the cranes, and (4) the location of the piece of equipment to allow maintenance people to work around the equipment - - - this specifically includes the orientation of the particular piece of equipment.

Jan 1, 1967

By William S. Alldredge

The Washington Metropolitan Area Transit Authority(WMATA) officially came into existence in February 1967 after the District of Columbia, Maryland, and Virginia joined in a com¬pact pursuant to Federal creative legislation signed the previous November to build a regional rapid rail transit system called METRO (1). The parent organization was the National Capital Transportation Agency (NCTA), a Federal agency, subject to Federal statutes and regulations. Soon after the completion of the transition from NCTA to the new "non-Federal" status of the Authority, the Board of Directors of the Authority formally adopted procurement policies and procedures (2). These are specific statements concerning competition by formal advertising for bids or by solicitation of proposals for negotiation, contracting authority, approval of awards, awards of contract modifications, and processing of claims and disputes. These policies and procedures are silent as to Federal procurement statutes and regulations. But because of the Authority's origin, the sensitive nature of the compact among the several sovereign jurisdictions, Federal financing of two-thirds of the costs, and the resultant surveillance by the General Accounting Office over staff operations, the Authority's procurement practices follow closely Federal regulations adapted to WMATA's needs. This is an important point and is the foundation of contractual relations between the Authority as the owner and its construction contractors. Various constraints and flexibilities of this arrangement with respect to excavation and tunneling contracts will be pointed out in the ensuing discussions.

Jan 1, 1974

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

It is imperative that the hydrogeologic frame- work and the ground water flow systems of a Potential mine area be investigated prior to initiation of mining. Such investigations are necessary so that potential mine water inflow problems can be anticipated and controlled. Obvious difficulties can arise if large inflows of ground water occur in underground workings. Costs of water removal and disposal, if not foreseen and included in economic planning, can severely limit or eliminate profit from a mining operation. Safety problems associated with large inflows are an additional potential problem. The inflow of water into a mine necessarily alters the associated ground water system. The inflow also may impact nearby surface water regimes, depending upon the interaction of the surface water and ground water systems. The inflow of water into a mine inevitably causes a decline in the ground water levels in the vicinity of the mine. This decline may be restricted to a small area or it may extend a considerable distance, depending upon the hydrogeologic properties of the associated hydrostratigraphic units. A decrease in surface flow will result if the area of ground water level decline intersects a stream or spring that is hydraulically connected to the ground water system. Mine inflow problems historically have been evaluated after-the-fact. Premining hydrologic investigations only recently have been initiated. Brown's (1977)* report on anticipated hydrologic impacts of oil shale mining in the Piceance Basin of Colorado is an example of premining hydrologic planning. Observed difficulties inherent in designing a data collection network and then utilizing the data to predict mine inflow have led us to the preparation of this manuscript. This manuscript reflects a two-phase effort. The first phase describes and develops analytical and numerical techniques for mine inflow prediction. Emphasis in this section is placed on the selection and application of data collection techniques and data analysis procedures. The second phase applies the prediction technique(s) developed during phase 1 to two existing mines. The objective of phase 1 efforts is to evaluate the hydrologic variables associated with surface water systems and ground water systems that can affect the inflow of water into an underground mine. Subsequently these variables are incorporated into predictive techniques for estimating underground mine water inflow and its effect on associated ground water and surface water systems. The specific objectives of phases 1 and 2 are to: 1) Determine the hydrologic parameters required for predicting underground mine water in- flow and the potential effects of the inflow on surface and ground water systems. The hydrologic parameters represent both premining and past initiation conditions. 2) Outline methods for obtaining the necessary input data for the predictive techniques in pre- mining and post initiation periods. 3) Present existing numerical techniques for predicting underground mine water inflow including assumptions Ad required input. 4) Evaluate existing numerical techniques previously tabulated based on their applicability to mine water inflow prediction. 5) Attempt to develop analytical techniques for predicting underground mine water inflow. 6) Develop, through modification of existing models, a general mathematical model as a numerical technique for predicting underground mine water inflow and the resultant effects on surface and ground water systems. 7) Apply the predictive techniques to two existing mines selected for this purpose. 8) Compare the predicted inflow rates to measured inflow rates at both mines. 9) Compare predicted impact on district hydrology to observed impacts where possible. 10) Evaluate the predictive technique.

Jan 1, 1986

By J. R. Frederick

Introduction In response to industry needs and requests, Joy Mining Machinery is aggressively evolving a "game changing" system of underground development mining machinery. This entry-development system (EDS) project is concentrated on providing clean, protected and ergonomic operator areas and a quantum leap in productivity. To meet these goals, a virtually continuous and automated mining system is needed. Operators must be able to efficiently and ergonomically perform required functions from a protected environment. Health-related issues, such as respirable dust and noise, must also be addressed. A new concept system of integrated face equipment, from the continuous miner to and including advancing the section belt and services, is needed. Phase I of the project was aimed at developing the bolting technology required. Through acquisition of Cram Australia and joint development efforts with Canyon Fuel Co., Joy now has this capability. The test platform, known as the Joy Multibolter, has successfully completed its trials at Canyon Fuel's SUFCo Mine (Fig. 1). These tests validated the bolting technology and operator protection and ergonomic issues. Phase II includes the development and testing of an integrated mining machine (IMM) capable of advancing a heading 1.5 m (5 ft) while simultaneously cutting a fullface width (single pass) and installing a complete bolt pattern. The IMM, unveiled at MINExpo 2000, incorporates the bolting technology of the Multibolter with automated full-face cutting. This machine was designed to meet Joy's stringent health, operator protection and 300m/d (1,000-ft/d) productivity goals. Phases III through V will include development of processes and integrated haulage, ventilation, power, material handling and section services advancing equipment. Processes and equipment developed will be designed for seamless integration into a complete entry development system. The focus of this paper is the new continuous miner (IMM) development, proposed testing and expectations for the EDS. The IMM is scheduled for commissioning and trials beginning in April 2001 at the SUFCo Mine. SUFCo Mine Canyon Fuel Co. is jointly owned by Arch Western Resources and the Itochu Corp. of Japan. It owns and operates three coal mines in Utah: the SUFCo Mine in Sevier County, the Skyline Mine in Carbon and Emery Counties and the Dougout Canyon Mine in Carbon County. Incorporating state-of-the-art-mining technology and advanced mine management practices, the SUFCo Mine is one of the most efficient underground coal mines in the world. The SUFCo Mine is located approximately 50-km (30 miles) northeast of Salina, UT, in the Wasatch Plateau portion of the Uinta coal basin. The mine property consists of 9,900 hm2 (24,470 acres) with approximately 118 Mt (130 million st) of recoverable reserves. Public utilities and industrial concerns purchase approximately 95% of the coal mined at SUFCo through short- or long-term contracts. Coal reserves are extracted by longwall mining, and the panels are developed using continuous miners. The longwall face at SUFCo Mine is 283-m (930-ft) wide, and the seam height ranges from 2.4 to 4 m (8 to 13 ft). The two development sections are in full operation using Joy 12CM12 continuous miners. Two super longwall panels, under development in the northeast portion of the lease block, are 4,270-m (14,000-ft) long with a 283-m (930-ft) wide longwall face. Each panel contains approximately 5.4 Mt (6 million st) of recoverable coal. SUFCo has been a world leader in productivity for a

Jan 1, 2003

By Greg J. Hasenfus, Allison M. Haines, Joshua M. Silvis

The floodable volume of longwall gob can be of great importance in developing accurate coal mine operation plans, particularly for mine water management and environmental control strategies. Given the inaccessibility and difficulty in direct measurement of gob characteristics following gob recompression, hydrologic, geomechanical, and spatial data and principles were used to solve for the porosity and height of the residual gob using a mathematical model framework and bulking-based techniques. Based on this approach, gob porosity of Appalachian longwalls appears to be tighter than previously reported, ranging between 4.99 and 14.31%. Residual gob height, as normalized with respect to mine extraction height, ranges between 1.90 and 2.45. A novel, bedding-based bulking approach is ampliative with respect to existing roof caving and bulking fundamentals, as it has greater explanatory value compared with the traditional, lithologic-based bulking application. The efficacy of using the residual gob characteristics determined by the mathematical model and bedding-based bulking is examined using a causal comparative method, whereby time series prediction of historical groundwater rebound is compared with observed mine pool elevation data. Prediction accuracy is significantly improved using a prototype model to calculate void volume of longwall gob, specifically, the dependence of porosity of the gob material upon the longwall width to overburden depth ratio for movement basins of subcritical and critical panel widths. The potential implication of these findings toward hydrologic, geomechanical, and ventilation studies of longwall gob could be significant.

Aug 13, 2021

By Todor P. Stefanov

The thermal draught within ventilation networks of underground mines depends to a great extent on the shafts depths and degree of change of ventilating air density. When the topology and space orientation of a ventilation network are constant, the dynamics of thermal draught is determined mainly by the variations of the heat- and mass-transfer processes in the openings. This conclusion follows from the well known basic theoretical notions about the thermal draught-aerostatics and thermodynamics [1]. Quantitative evaluation about the influence of heat- and mass-transfer processes on dynamics of thermal draught could be made through: direct mine measurements, special experiments and with the aid of mathematical models. The first two methods produce sufficiently accurative results, however it is very difficult to perform such studies, particularly when these processes are evaluated within a large scope and multifactor aspects. Mathematical models of thermal draught allow to overcome easily these difficulties. The degree of accuracy of results, obtained by this method, depends to a great extent on the degree of approximation achieved by the model to the real heat- and mass-transfer processes. In this paper, with the aid of Bulgarian developed method, algorithm and computer program V WT-4 - for complex evaluation of ventilation parameters in active mine ventilation networks [2], the authors investigate some changes in the thermal draught. Basically, the method is an iterating evaluation of an open set of equations, which represents relationships between the following basic parameters of a mine ventilation network: [ ]

Jan 1, 1980