Search Documents

By J. Organiscak

A majority of continuous mining machines employ a water spray system and a machine-mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine-mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays and scrubber airflow on dust and gas levels, while using a 12.2-m (40-ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1-m (20-ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complement the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off-curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

By Scott G. Britton

The first section of this text delves into construction engineering techniques for successfully completing necessary underground production support projects. I will discuss alternative design concepts, installation practices, materials and material costs, completion time, and necessary labor for individual projects. The emphasis of this section is on describing each project thoroughly and providing a practical guide for the supervisor or engineer. There are four main construction categories for typical underground mining projects. These are: 1) Transportation of men and supply materials. This refers to track and wire installation and roadbed grading and ballasting. 2) Ventilation, composed of overcasts, man doors, regulators, and stoppings. 3) Drainage, including sumps, pumping stations, drainage networks, pumps, and face drainage. 4) Haulage of coal and rock from the face to the outside. The focus here is in the installation of belt lines, belt drives, transfer points, and vibrating bins/feeders. The first section shall fully discuss these four categories in regard to the construction engineer or supervisor designing, building, or improving a system. In addition, special projects such as surge bins, rotary dumps, and underground offices not classified under these categories will be discussed. For manageable purposes, I have limited the installation discussions to one or two approaches I feel have merit. The variation of installations in coal mining is endless, each with its own advantages and disadvantages. Therefore, the reader should not dismiss or restrict his thinking to only the approaches in the text. It serves as a guide only.

Jan 1, 1983

By Mark C. Williams, Shunsuke Managi, Noriko Hikosaka Behling

Particle processing is a key to using solid particles in fuel cell applications. Selectivity with regard to reactivity, impurities, etc. is an important feature and the treatment of particle surfaces could greatly impact the performance of direct carbon fuel cells. Solid fuel particles will become increasingly important in the future. Present energy conversion systems for solid fuels are too inefficient. New energy conversion systems for solid fuels with higher energy conversion efficiencies are possible. Fuel cell technology is a key technology in these new conversion systems. The direct carbon fuel cell (DCFC) operates on carbon particles obtained from a variety of solid fuel feedstocks. The DCFC is the only fuel cell designed to directly oxidize carbon particles in a special anode chamber. The particles are generally graphite structure with high purity. The electrolyte used is the high temperature solid oxide, molten carbonate, or hydroxide electrolyte. Since a pure stream of CO2 is produced, the stream can easily be sequestered and disposed. Pure carbon dioxide produced as a by-product would also have a market in many industries. A well-defined technology roadmap identifying key research and development (R&D) issues is necessary to provide a framework for the development of these systems and to prevent entrenchment in inherently inefficient technologies. This review paper describes the direct carbon fuel cell and its system, how it works, the developmental status, the characteristics of the carbon particles needed, and the research and development issues for the technology

By Jie Li, Longxiang Li, Wenbing Guo, Gaobo Zhao, Yuhang Hu

Surface subsidence caused by underground longwall mining is a very complicated process in time and space, influencing building and structures on the surface of the mining area, including houses, pipelines, and highway. The field monitoring data of surface subsidence are essential for protecting them. This study investigated the dynamic and residual subsidence characteristics of both the surface and the highway over a 730-day monitoring period on a longwall panel. Three monitoring lines (Lines 1–3) were established to monitor the subsidence process, and three stages were identified: initial stage of surface subsidence, active period of surface subsidence, and residual subsidence deformation stage. The maximum subsidence value on the highway (1,786 mm) was smaller than that on the surface (2,094 mm), and the maximum subsidence velocity on the highway (41.7–50.8 mm/day) was also lower than that on the surface (66.7 mm/day). During the residual subsidence deformation stage, both the surface and highway subsidence velocities decreased to below 0.6 mm/day. Furthermore, differences in subsidence characteristics between the surface and the highway were analyzed, with the subsidence value on the highway always being less than that on the surface, while the subsidence velocity during the residual deformation stage was not always lower. This could be attributed to the influence of dynamic loads from vehicles, which could induce additional residual subsidence on the highway. Further investigation into this phenomenon will be conducted in future research.

Jul 1, 2023

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By Keros Cartwright

Sanitary landfilling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for any natural limitations at a particular site Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) Regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites. (2) Site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources. (3) Re- search on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills. (4) Formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers.

Jan 1, 1970

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By James M. Barker

No commodity agreements now exist for sulfur and a lack of reference to sulfur commodity agreements exists in the literature. Law (1975) made a passing reference to sulfur as one of a group of commodities where "there have been additional control efforts of various types." Clearly, sulfur was a candidate, at least conceptually in the past, for some form of commodity agreement and the following discussion centers on the world sulfur market of the early 1980's in this context. GENERAL THEORY OF COMMODITY AGREEMENTS The upsurge in demands for commodity agreements seen in the last decade or so stems largely from agitation by the less developed countries (LDC) for better economic treatment by more developed countries (MDC). Several economic factors, real or imagined, adversely affect the LDC's as follows (MacAvoy, 1977): 1) variable demand in MDC's causes wide fluctuations in commodity prices which hurt the economies of commodity producers, who are often LDC's although consumer economies may also benefit from more predictable prices; 2) a general decline of commodity prices relative to the price of manufactured goods which hurts commodity producers in their balance of trade while their stocks and overcapacity rise; 3) instability of LDC economies enhanced by the above factors lowers internal stability, inhibits foreign investment, and retards economic growth; and 4) a lack of self respect when dealing with developed countries o, following the OPEC lead, LDC producers want the stature related to cartel market power.

Jan 1, 1985

By R. M. Von Storch

Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that influence miring. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined, conditions are met in most coal mines in southeastern Utah including those of the United States Steel Corporation. This coal bed measures up to 16 feet in thickness, the pitch is as much as 25% and mining is under a cover approaching 2, 000 feet. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colorado. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest..It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development.

Jan 1, 1967

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By Harold Wagner, Prakash Donde, Larry H. Heflin

INTRODUCTION The Washington Metropolitan Area Transit Authority is responsible for the planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. Some 117 kilometers (72.8 miles) of this system is in operation and contains 30.6 route-kilometers (19 miles) of rock tunneling. To complete the planned system an additional 1.6 kilometers (1.0 miles) of single track tunnels in rock are planned and additional contracts will consist of 4 kilometers (2.5 miles) of twin tunnel, resulting in 8 additional linear kilometers (5 miles) of single track tunnel contracts yet to be offered in soft ground. Three recent contracts in soft ground included the New Austrian Tunneling Method (NATM), along with conventional tunneling, as a bid option. Section E5a, Fort Totten Station and Tunnels, was the only one of the three to be constructed using the NATM option. This is the first application of the New Austrian Tunneling Method in soft ground in the United States. This paper will concentrate on the Fort Totten Station chamber NATM design, construction, and the instrumentation readings and evaluations which lead to an engineering back analysis which allowed a refinement of the bid design, resulting in a faster, more efficient construction. Design of the Fort Totten Station and Lines was done by Sheladia Associates. The design team included Greiner Engineering and Jenny Engineering with Mayreder-Consult of Austria, who was responsible for NATM design and NATM construction consultation.

Jan 1, 1991

By Rihab Guellala

In Tunisia, the Paleocene-Eocene series has an important socio-economic interest. It contains profitable oil and water accumulations. Moreover, it encompasses phosphate reserves. The present study uses seismic reflection prospection and borehole data for the reconstitution of the Paleocene-Eocene deposit structure in the Jerid area (southwestern Tunisia), a crucial step for the phosphate exploitation. Firstly, lithostratigraphic correlations incorporating water and petroleum wells were established according to different directions for a tentative approximation of the Paleocene- Eocene deposit geometry by following their lateral evolution. To give more details, seismic reflection profiles were interpreted in the second step. The Paleocene-Eocene formations were associated with their corresponding reflectors on the closest seismic profile using the relation of time and depth in petroleum wells. Analysis of lithostratigraphic correlations shows notable variations in the Paleocene-Eocene series thickness and depth. Seismic profile interpretation explains these variations by highlighting different buried tectonic features. The results confrontation reveals that the phosphatic deposit geometry in the Jerid area is mainly influenced by the (1) emergence of the Saharan platform and the Chott northern chain since the Late Cretaceous, (2) syn-sedimentary normal activity of E-W and NE-SW faults during the Paleocene-Eocene epoch, (3) reverse-reactivation of these faults, and (4) major Tortonian folding phase. This study can enormously enhance the Jerid area socio-economic development by presenting useful findings that may orientate the phosphate exploration.

Aug 15, 2021

By Peter A. Gillett, Ian S. Clelland, J. G. S. Hynd

Today mine shaft and slope contracts include a greater amount of ancillary work such as level and pump stations, loading pockets, rotary and side dumps and connecting raises. This ancillary work requires the application of a number of construction methods often for short periods and often at short notice if the contractor is to maintain a profitable operation. In the next decade, the number of shafts that will be sunk by a boring method will outnumber those sunk by traditional methods. This will be particularly true of the deeper shafts where water problems are minimal. The increase of bored shaft work will not decrease the work completed by the shaft sinking contractor but it will change it. A greater emphasis will be placed on the speed of construction of station and other ancillary work. To meet this challenge the contractor requires full information on the ancillary work as well as the shaft work at an early date, preferably pre-bid. The two examples discussed in this paper illustrate the importance of early information. The two main factors of shaft ancillary work construction are sequence and ground support. This paper describes two examples completed recently by The Cementation Company of America Incorporated in Arizona. The first described is a Rotary Dump-Ore Pocket-Ore Pass complex and the second described is the excavation of the Main Station Level in a 2 Station-Loading Pocket-Ore Pass complex. CONSTRUCTION OF ROTARY DUMP, ORE POCKET AND PASS Introductory

Jan 1, 1976

By Edwin G. Johnsen

Underground mining is relatively safe today, but no technique or equipment is completely fool proof and 100% reliable. The only sure way to prevent accidental death or injury to underground workers is to remove them completely from the hazardous environment. This alternate approach to underground work is now feasible. Tunnelling and mining systems can be built that could be remotely controlled by men operating consoles in a surface control room. This concept, called a teleminer, would use recently developed remote control technology to remove man from underground work but still give him the capability to remotely operate mining and excavating equipment as if he were actually in the working area. It is appropriate to present this concept in the session "Environmental Controls" because the rationale for environmental control in underground areas can be significantly modified if man is excluded from the underground operation. The development of teleminers cannot only reduce or eliminate most of the requirements for conventional environmental control, but it can also create new and powerful techniques for rapid tunnelling and excavation. TELEMINER CONCEPT The concept of remotely controlled mining machines is neither new nor untried.(1)(2) Conventional remotely controlled mining equipment employs the standard techniques of extending the controls of the equipment to a remote console. For example, the rotary cutters on a remotely controlled tunnelling machine are started or stopped by a human operator turning a switch on the remote control console.

Jan 1, 1997

By John C. Cook

In reasonably dry rock, long-wave radar can theoretically explore to distances approaching 75 meters (250 ft). High-resolution radar reflections have already been demonstrated through 13 m of hard limestone, through 9 to 18 m of coal in place and through 225 m of rock salt, using only low-power experimental radar equipment. Radar reflections have been received through the rock from rough pillar walls, from faults, and from a slim, uncased, vertical drill hole. In three years of intermittent experimentation, the feasibility of rapid radar exploration of large volumes of rock, with portable equipment, in deep, wet workings has been demonstrated. With future, improved equipment the theoretical working range, of the order of 75m, is expected to be attained in most hard rocks. THE TECHNIQUE Fig. 1 illustrates an early "monocycle" radar system (1) set up in a coal mine. This radar equipment is entirely different from that employed for detecting distant objects through the atmosphere. However, the basic principle is the same: a pulse of electromagnetic energy is radiated by the transmitter, a portion is reflected by some "target" object embedded in the surrounding medium and some of this energy is collected by the receiving antenna. In the receiver, the pulse is amplified, is "stretched out in time" by a sampling process, and is displayed on the screen of a cathode-ray oscilloscope. It may also be recorded on paper or magnetic tape. Fig. 2 illustrates a

Jan 1, 1997

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979

By Tim Neil, O&apos

Introduction Compania de Carbones de Chile (Cocar SA) has brought into production Chile's first large-scale, open-pit coal mine, located in the Magellan Province. The US $65 million project includes a 1.1-Mt/a (1.2-million stpy) subbituminous steam coal mine and a mechanized bulk loading marine terminal with water depth sufficient to receive 60 kt (66,000 st) Panamax vessels. The loading terminal will be one of the largest in Chile. The Pecket coal project is expected to save Chile about $40 million in energy production costs and a further $100 million in oil imports, or about 25% of the country's oil import costs. Pecket coal will generate electricity for Codelco and will also supply general electricity needs for northern Chile. The Pecket coalfield is located on the Brunswick Peninsula, about 30 km (19 miles) northeast of Punta Arenas, the provincial capital, as shown in Fig. 1. Pecket is part of a large, coal-bearing basin. It extends from Punta Arenas 250 km (155 miles) north to Puerto Natales and across the border into the Rio Turbio coalfield in Argentina. A fleet of large and small O&K hydraulic shovels and backhoes is used to dig and load overburden and coal into mining trucks while O&K graders maintain the haul roads in and around the pit. Coal occurrence in the Magellan area of Chile has long been

Jan 1, 1988

By G. Biles

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralized zones, which are less economic or uneconomic as direct shipping ore. Testwork demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and ISO tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime's shares and manages and operates the mine on Prime's behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts' administration.

Jan 1, 1999

By I. H. Warren

Hydrometallurgy has a well-known and established role in the production of manganese metal (1) and manganese compounds, including battery grade manganese dioxide (2). Also, several leaching processes have been developed and applied at various times for the recovery of manganese from low grade ores (3). Recently, interest in the hydrometallurgy of manganese has been stimulated by the problems presented in the processing of sea nodules (4). Fumes and dusts from the ferro-manganese furnaces also offer a potential field for the application of manganese leaching techniques (5). In treating low grade manganese ores a major requirement of the leaching process is that it should dissolve manganese from a mixture of manganese and iron oxides. The most selective reagent for this purpose is ammonium carbamate applied after preliminary pyrometallurgical reduction of the ore (6). Since soluble carbamate complexes of the postulated type (7) are formed by both manganous and ferrous, but by neither manganic nor ferric, ions, selectivety of manganese leaching is achieved by control of the reduction operation to yield, essentially MnO and Fe304? A potential improvement to this two step process would be to simultaneously reduce and selectively leach the manganese in one hydrometallurgical operation. This possibility has been experimentally studied and the results are described below. During the preliminary study of the stability of solutions of ammonium, ferrous and manganous carbamates at elevated temperatures, it was observed, contrary to the observation of Welsh (8) at lower temperatures, that

Jan 1, 1971