Search Documents

By R. W. Smith, D. Clare

The removal of metals from an acid mine drainage (Leviathan Mine, Alpine County, California) water by precipitate flotation was investigated. The Leviathan waters vary from about pH 4.0 to pH <2.0and contain from about 2,000 to about 12,000 ppm SO42-.The main multivalent metals present in solution are Fe, Ca, Mg, Al and Mn. Both Cu and Co are present in small amounts. The pH was adjusted with lime. The collector used was either sodium oleate or tall oil. The sodium oleate was used as a function of pH to establish optimum flotation conditions and the tall oil was used only at the optimum pH. Dow Froth 250 was used as a frother. In some test additional Cu was added to the system. Excellent recovery of Fe and Cu were achieved at optimum pH. The process achieves results comparable to precipitation and filtration without as much problems with screens blinding because of less material to filter.

Jan 1, 2004

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003

By John D. Morgan

The United States is the world&apos;s most productive nation and its citizens enjoy one of the highest material standards of living of any people in the world. Materials and energy are the lifeblood of any industrialized economy. Annually the United States uses over 4 billion tons of mineral materials and fuels, or 40,000 pounds per person as detailed in Figure 1. Domestic processed materials of mineral origin and energy are valued at more than $150 billion annually, and they are derived largely from domestic sources, supplemented by imports, as detailed in Figure 2. In recent years the superior productivity of the United States has also enabled it to give food and manufactured articles to many other less fortunate nations and peoples of the earth. What then is our concern with materials at this time? Seeing the burgeoning increases in our mineral demand: from 2 billion tons in 1950, to over 4 billion tons today, and projected to 11 billion tons by 2000 - we are getting questions concerning our ability to continue to increase production sufficiently for the future.

Jan 1, 1974

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025

By M. F. Werneke

Flotation of the carbonate, oxide and silicate minerals of copper (malachite, azurite, chrysocolla) has been the subject of much research in recent years, but few effective solutions to this problem have been found. With decreasing reserves of sulfide minerals, the economic recovery of these "oxides" appears to be an important source of copper for the future. Xanthates have been known for many years to be malachite collectors (1), but only at very high dosages, or at lower dosages following activation of the mineral by sulfide ion. Dewitt and Batchelder (2, 3) found that chelating agents such as certain oximes were collectors for malachite and azurite, but also required high reagent dosages. Fuerstenau (4) has suggested, for example, that potassium octylhydroxamate may be an effective collector for malachite, On the other hand, Balberyszski (5) has found that oxide minerals may be completely sulfidized at high temperatures with gaseous sulfur or H2S, and then floated with conventional collectors. None of the above approaches appear to offer an economically effective method for the direct flotation of these oxide minerals.

Jan 1, 1977

By Siyu Song, Yanhong Wang, Guohua Gu, Linbo Huang

In this study, the effect of cations, Na+ and Mg2+, in saline water on copper flotation in the presence of calcium bentonite was investigated. It was found that as the concentration of NaCl was increased, the copper recovery initially decreased and then increased to above 99%, while the copper grade initially increased and then decreased. In contrast, as the concentration ofMgCl2 was increased, the copper recovery continuously increased, while the copper grade continuously decreased. The variation of copper recovery and grade was mainly attributed to the synergistic effect of pulp rheology and flotation solution chemistry. The underpinning mechanisms are the compressing electrical double layer and ion-exchange interaction between saline water and bentonite, which occur at the same time. Using salinewater slightly affected the pulp rheologywith a decrease in copper recovery at low NaCl concentration. Increasing the concentration of cations in saline water might even facilitate the flowing out of exchangeable cations, especially divalent cations, from the interlayer space of bentonite to the solution, resulting in the decrease of copper grade at high salt concentration.

Sep 10, 2020

By John C. Draper

Little precise information is available on the effect of mining on the surface topography. It is often assumed that after mining the surface will simply sink. This is not an infallible conclusion as is well illustrated in two of the three examples herein. This paper describes the results of an attempt to precisely measure the surface movement in the area around coal pillars left in place for three oil wells in a completely mined and caved area at the Harwick Mine of the Duquesne Light Company. The dates when the various measurements were made are shown on the data sheets and indicate the rate of surface movement. These oil wells are identified as wells Nos. 2, 3, and 6. This mine property is located on the north side of the Allegheny River at Cheswick, Pennsylvania, and extends in a northerly and westerly direction about five miles. The three well pillars are situated on the westerly side of the Bessemer and Lake Erie Railroad some 2,000 feet from Rural Ridge, Pennsylvania (Fig, 1).

Jan 1, 1964

By Toshio Fujiwara, Sumikichi Ito, Masao Kitamura

The Tennohji-Benten Giant Trunk Sewer Project has been under construction since 1974 in the eastern part of Osaka, the second largest city in Japan. The entire project is divided into 7 blocks, some of which have already been completed. This 8.8-km sewer tunnel, being driven through a densely populated area, was planned to be constructed by the shield tunneling method. This paper described shield tunneling performances and ground behaviors during the construction of Blocks 2 and 3. An earth pressure shield (dia., 6,750 mm) was employed in Block 3 tunneling. The ground was generally soft and the cover over the tunnel varied from 13 m to only 4.5 m, so that a considerable amount of chemicals was injected to stabilize the ground. A hand-digging type shield (dia., 7,250 mm) was used in Block 2 tunneling under compressed air. For 85 m of the total length of 1.6 km, the soil at the face was extremely soft, and therefore, the ground freezing method was additionally employed.

Jan 1, 1981

By Rameshwar Sah, Basavaraja Maribasappanavar, Sangamesh Desai, G. Balachandran, Ravi Kant Sagar

The present research work deals with the effective utilization of hematite ore containing goethite, kaolinite and gibbsite losson- ignition (LOI) phases in pellet making without deteriorating product pellet properties by optimizing the induration cycle especially drying and preheating of pellets. Adequate drying and preheating of pellets before sintering is of prime importance to sustain the desired properties of pellets. Green pellets of + 8 to − 16 mm size were prepared in a laboratory disc pelletizer and indurated by varying drying and preheating temperatures in a laboratory Raising Hearth Furnace (RHF). Produced pellets were assessed for physical and metallurgical properties. Improvement in drying and preheating temperature simultaneously helped in mitigating fired pellets’ property deterioration. Drying at 300 °C and preheating at 750 °C helped in the maximum removal of matrix LOI from the pellets before firing and enabled the production of pellets of desired properties. Laboratory scale findings successfully implemented at existing 4.2 MTPA capacity pellet plant of JSW Steel Ltd. Vijayanagar and high LOI iron ores (IOs) utilised which resulted in reduction of average monthly pellet fines generation by ~2 wt. %.

Jun 4, 2022

International Minerals & Chemical Corp.&apos;s New Wales operation near Mulberry, FL, is reportedly the world&apos;s largest concentrated phosphate chemical fertilizer and phosphate-based animal feed ingredients complex. Its latest expansion represents a $191-million investment. Two Northwest draglines were put to work at the operation early last year and, according to a company spokesman, total production from the units have more than doubled that from older rigs. This article describes how the draglines are used and provides details on the New Wales operation. The principle product at New Wales is phosphoric acid, produced by reacting ground phosphate rock with sulfuric acid in large concrete attack tanks. For each ton of phosphoric acid produced, New Wales must dispose of about 4.5 t (5 st) of waste gypsum. New Wales stores the gypsum on-site, and uses durable Northwest draglines to help handle the material. Two Units Maintain the Gypsum Stack After the gypsum is separated from the phosphoric acid through 23-m-diam (75-ft-diam) vacuum filters, it is mixed with water from a 121-hm2 (300-acre) recirculating cooling pond and, in slurry form, is pumped to the top of a 121-hm2 (300-acre) gypsum stack located adjacent to the cooling pond. The slurry contains mostly gypsum (CaSO4), with small traces of silica and other elements. The water at this point is corrosive, containing from 1-2% phosphoric acid. Its pH usually ranges from 1.5-2.0. Water drains from the gypsum stack into the cooling pond. Only about 15% of the pond&apos;s water, however, comes from the gypsum stack; the balance is from various sources throughout the complex and is held in the pond to cool before being returned for reuse in the plant. About 97% of New Wales&apos; water needs come from this recycling program. The gypsum remains on the stack, inert, ready for future processing if it becomes economically feasible. Throughout the handling process, Northwest draglines work around the stacks&apos; rim, continually directing the waste flow and digging out dried solids to heighten the perimeter dike to provide more storage volume. When wet, gypsum is extremely soft. When dry, it compacts well and provides footing with enough bearing capacity to support the machines. Processing at New Wales started in 1975 and the gypsum storage area has already been built up 12 m (40 ft) above grade. A total of 14.8 km3 (12,000 acre-ft) of solids are now stored. The draglines dredge material from near the perimeter dikes and place it to build parallel berms. This

Jan 8, 1982

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not coprecipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Nov 1, 2011

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not co-precipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Jan 1, 2011

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By D. Malhotra

The number of variables which can effect flotation of molybdenite is very large. This paper discusses the effect of two operating variables, namely, the degree of aeration and agitation, on the grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." The analysis of flotation results indicate that molybdenite can be characterized into fast-floating and slow-floating components. The rates of fast-floating components, which do not create a problem in flotation, could be varied by changing agitation of airflow rates. However, the rate of slow-floating components was stable and was only a function of residence time in the float machine. The degree of aeration has a significant effect on the grade of MoS2 with only a slight effect on the recovery of MoS2. The degree of agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits is subsequently discussed.

Jan 1, 1977

By A. Lashgari, V. Kecojevic

This paper presents research on the environmental impact of digging and loading equipment used in surface coal mining. Environmental impact was assessed through the measurement of equipment exhaust and dust emissions, and sound level. In this study, exhaust emission refers to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx) and volatile organic compounds (VOCs). Dust generation refers to fine particles (PM2.5), inhalable particles (PM10) and total suspended particulate matter (TSP). Sound level refers to the sound pressure level at different distances from the equipment. Modeling of the environmental impact of digging and loading equipment was conducted using the Microsoft Visual Studio.NET software package. This research was a part of a broader project involving the development of a software system for the selection of productive, cost-efficient and ecofriendly mining systems, sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). This research may assist mining professionals in quantifying the environmental impact of digging and loading equipment, and developing strategies for reducing the overall impact of such equipment in surface mining.

Jan 1, 2013

By LeEtta M. Shaffner, John R. Marks

The Homestake Gold Mine in Lead, South Dakota, commenced operations in 1876. As is the case with old, deep, continuously developing mines, a ventilation improvement is periodically required to maintain acceptable underground environmental conditions. Recent historical improvements at Homestake include a 5.2m diameter air shaft driven in the 1960&apos;s and a 2.1 MWR (580 ton) chilled water plant installed in 1978. By 1983, it became apparent that yet another ventilation upgrade would be needed to keep pace with accelerated development in the deepest mining sections. A study was therefore undertaken to project ventilation requirements for the next ten years and to select the method(s) most suitable to meet those requirements. The study called for a two-phase approach in which air flow and air conditioning were carefully balanced. Phase I, the installation of a new 2240 kW surface fan and several underground circuit changes, was completed in 1986. This paper describes Phase 11: the planning, design, installation and initial performance of the air-conditioning portion of the upgrade.

Jan 1, 1989

By Bruce A. McKinstry

Introduction For many major mining projects the time frame from initial planning to production can be measured in decades. Hecla&apos;s Silver Shaft project, scheduled to go into production by the end of this year, includes a complete surface facility, shaft with an ultimate depth of 2.4 km (7,700 ft), complete ore pass and loading pocket system, and 610 m (2,000 ft) of development drifting and stope preparation. The project was conceived in the fall of 1979, and the duration of a mere four years from conceptual engineering to production is testimony to what can be accomplished when a mining company and a contractor work as a team rather than developing into two warring camps, as often happens. Engineering In 1979, Hecla Mining Co. awarded a contract to J. S. Redpath Corp. to perform feasibility investigations and design engineering related to a proposed new shaft facility at the Lucky Friday Mine. The Lucky Friday, in Mullan, ID, is a major producer of silver, as well as significant quantities of lead and some zinc. In late 1979, stoping was in prog-

Jan 10, 1983

By Gary L. Simmons

Over the past several years, Newmont Gold Company (previously Santa Fe Pacific Gold Corporation) developed a new technology for the flotation of refractory auriferous sulfide minerals which is referred to as the N2TEC flotation process. Starting in April 1997, the first commercial flotation plant utilizing N2TEC technology was successfully commissioned at the Lone Tree Mine near Valmy, Nevada. The Lone Tree flotation plant was designed to process 4,085 mt/d of ore producing 494 mt/d of sulfide concentrate. A flotation tails leach CIP circuit was added to recover cyanide-soluble gold from the flotation tails. A portion of the flotation concentrate is blended with whole ore feed to the Lone Tree autoclave, up to the limit imposed by the current oxygen plant capacity. The remainder of the concentrate is shipped to either the Twin Creeks autoclaves or the Carlin roaster for subsequent oxidation and gold extraction. This paper discusses the results achieved in the commercial flotation plant compared to pilot plant testing and engineering design flotation modeling. Capital and operating cost information are also presented.

Jan 1, 1999

By Landy A. Stinnett

Coal mines in the United States are the most productive in the world in terms of efficient labor employment. This is because of an abundance of workable coal beds, large infusions of capital, improved management practices and continuing competitive pressures. The standard unit of measurement for labor productivity is expressed as tons/manshift, although for underground mines, operators often refer to tons per machineshift. Articles written concerning labor productivity generally focus on measurement techniques, safety considerations, application of technology and training. This article will illustrate by example the impact of labor efficiency (or inefficiency) on the ultimate selling price of coal, f.o.b. mine site. During the past several years, the coal industry has seen significant improvement in labor use. Figure 1 shows the trends in productivity for all active mines in the United States from 1985 through 1994. Productivity in 1985 was 20.1 t/manshift (22.1 st/ manshift). This factor has increased almost linearly throughout that period to 37.5 t/manshift (41.2 st/manshift). This is a 7.2% annual compound growth rate.

Jan 1, 1995

By G. D. Hood, C. E. Jordan

The US Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water and ore, selectively attaching these bubbles to the hydrophobic mineral&apos;s surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67% copper and with a phosphate-bearing amine flotation tailings sample containing 9.5% P2O5 in a quartz matrix. Over 88% of the copper was recovered from the ore in a rougher concentrate containing 5.9% copper at a rate seven times, faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate four times faster than conventional flotation. The unfloated product retained 80% of the phosphate in a 16.9% P2O5 concentrate.

Jan 1, 1994