Search Documents

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1931 was 30, a decrease of 20 fatalities or 40 per cent from the number killed in 1930. As a result of the decrease in the number of fatalities for 1931, the fatality curve of tie California petroleum industry reached its lowest point in nine years. Although reductions in personnel--which permitted the retention of a select and experienced class of workmen, decreased active field-development work, and curtailed production--undoubtedly have had a marked effect on reducing the number of fatalities in 1931, the decrease also has resulted from continued accident-prevention efforts. Statistics show that a direct relationship exists between development activity and the number of men accidentally killed in the drilling and producing division of the California petroleum industry. For example, when the average number of drilling wells in 1930 was 29 per cent less than in 1929, the number of men accidentally killed at drilling wells dropped 48 per cent; and when the average number of drilling wells in 1931 decreased 52 per cent from 1930, the number of fatalities at drilling wells decreased 58 per cent. The relationship between field-development work and fatality frequency is significant because each year at least 50 per cent of all the fatalities in the California petroleum industry occur in the drilling and producing division. This relationship should serve to guide the accident-prevention efforts of the industry, especially in the drilling and producing division, toward checking an increase in fatal accidents when development activity again takes an upward trend.

Jan 1, 1932

By J. B. Clemmer

This report summarizes the results of u laboratory study of the beneficiation of Arkansas bauxite by flotation. Although the investigation is not yet completed, a preliminary retort of the results on several typical bauxites is presented to show the merits rind limitations of flotation for the production of concentrates acceptable to the aluminum industry. It is

Jan 1, 1941

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

By F. P. Haver

The Federal Bureau of Mines developed a 10,000-ampere cell to determine the economic feasibility of producing high-purity electrolytic titanium from mill scrap or offgrade sponge. Operating variables were investigated, matetial handling procedures were established, and the cost of electrorefining titanium was determined. The prototype cell produced premium-grade metal (<100 Brinell hardness number (B.h.n.)) from very impure Kroll sponge at a processing cost of less than $0.60 per pound. Refined metal was deposited at the cathode in the form of coarse (85 percent plus 34-mesh), hexagonal crystals of a titanium when the cell was operated an 850° C. A cathode current density of 1,000 amperes per square foot and a molten sodium chloride electrolyte containing approximately 5 percent by weight of soluble titanium were used. In continuous operation, at the optimum number of ampere-hours, (40,000), the current efficiency averaged slightly less than 60 percent. It was possible to supply large enough amounts of electric current for electrolysis to maintain the temperature of the bath, thus reducing overall power consumption to less than 5 kilowatt-hours per pound of metal refined.

Jan 1, 1961

By Max J. Spendlove

The secondary copper industry is comprised of numerous enterprises which collectively employ many of the recovery and refining processes now used in primary plants as well as many other processes that are unique to the industry. Effective methods are used for identifying and segregating all types of scrap according to widely accepted standard classifications. Segregated scrap and waste materials usually require some preliminary processing to remove both valuable and deleterious associated constituents. Smelting, melting, alloying, and pyrorefining are common methods used for producing secondary metal, but operating techniques usually differ from primary metal operations because of the difference in physical and chemical properties of the respective raw materials. Some copper scrap is converted to copper chemicals rather than to refined metals or alloys. Recovery efficiencies of all processes are reasonably high, and the quality of products meets rigid specifications.

Jan 1, 1961

This report is the 25th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations, and the 7th of these reports to be issued on a calendar-year basis.3 It reviews briefly work in progress during 1960, and furnishes references to publications by Bureau personnel during 1960 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned can be found by referring to the publications cited in the footnotes or in the further list in the Miscellaneous section; other phases of work are reported here for the first time and will be covered in more detail by later publications, Coal programs of the Bureau of Mines extend over the wide range of theoretical and applied studies indicated by the table of contents. Fundamental research on coal structure and on the properties of coal will, over a period of time, increase the general knowledge about coal Which scientists and engineers may use in answering practical questions and in solving problems in the mining and utilization of coal. More applied studies are conducted in connection with the developement and evaluation of new mining techniques and the effective processing and utilization of coal and of coal products. Health and safety activities, analyses of coal being mined, and technical advice and assistance to Federal agencies in connection with fuel and boiler-water problems are among the practical services handled by the Bureau.4 5

Jan 1, 1962

By H. D. Kline

This publication describes mining and milling methods and costs at the Madison mine of National Lead Co., St. Louis Smelting & Refining Division, in the Fredericktown district of southeast Missouri and is one of a series prepared by the Federal Bureau of Mines on methods, practices, and costs of mining and milling throughout the United States. The are bodies of the Madison mine are known for the complexity and diversity of their are minerals. Sulfides of copper, nickel, and cobalt occur in commercial quantities with lead sulfide, which is the most valuable metallic mineral in are bodies of the Bonne Terre formation in southeast Missouri. Several attempts were made by various operators to mine the complex ores and separate the sulfide minerals before 1927 when National Lead Co. became interested in the Fredericktown district. Operating then as the St. Louis Smelting & Refining Co., the company began mining and milling ores from the Madison mine in 1944 and has operated continuously since then. A recently built refinery produces copper, nickel, and cobalt metal from a concentrate containing iron sulphides and small quantities of copper, nickel, and cobalt sulphides.

Jan 1, 1961

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil-production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By Howard W. Wainwright

This bibliography was compiled by the Bureau of Mines as part of an investigation into the possible utilization of low-temperature coal-tar bases. The bibliography consists of literature and patent references from about 1945 to 1961 and is divided into the following headings: Analysis and Composition; Production, Synthesis, Reactions, and Utilization; and Separation, Purification, and Properties. Although over 1,000 references are included, no attempt was made to insure a comprehensive survey. The literature and patent references are arranged alphabetically by author or patentee. When several publications have the same author they are listed in reverse order of age, with the newest first. An author index is included because secondary authors are not cross-indexed. In almost every instance, the entry is accompanied by a Chemical Abstracts reference for those interested in locating an abstract of the original paper.

Jan 1, 1962

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation&apos;s coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965

By J. F. Neill, O&apos

The manganiferous schists occurring in the vicinity of Kings Mountain, North and South Carolina, suggest significant tonnages of potential submarginal ores. Although some reconnaissance work in connection with these deposits has been reported, no recent information has been published. Evaluation of the schists as a possible domestic manganese resource has not always adequately considered the fact that the manganese content occurs quantitatively both as oxide and as the silicate, spessartite. The Bureau of Mines investigation herein reported includes preliminary studies to indicate the extent of manganese oxide mineralization and to deter-mine the amenability of the material to sulfur dioxide leaching. The field reconnaissance studies suggest a resource containing in one area an average of 6.4 percent manganese as oxide. The procurement of depth information was beyond the scope of the investigation.

Jan 1, 1962

A pilot program was undertaken to evaluate a process developed by the U.S. Bureau of Mines to recover nickel, cobalt, copper and chromite from domestic nickel laterite resources. An existing five ton per day pilot plant was modified to accommodate treatment of laterite by the Bureau process, which employs reductive roasting, ammoniacal sulfate leaching, solvent extraction, and electrowinning to extract, separate, and recover nickel, cobalt and copper as high purity cathode products. Three distinct types of laterite i.e., limonite, saprolite and a mixture of limonite/saprolite were processed through the plant during three operating campaigns. Nickel cathode was made during all three campaigns, while cobalt cathode and chromite concentrate were recovered only during processing of limonite. Leach extraction of nickel and cobalt averaged 83 and 67 percent, respectively, while the overall recovery was 80 and 63 percent for nickel and cobalt, respectively. Initially, over-reduction of iron in the saprolitic calcine contributed to poor settling of the leached solids. This problem was overcome by careful control of reducing conditions and flocculant addition. An economic feasibility study was made for a 5000 TPD grassroots laterite processing facility scaled-up from pilot plant data. Estimated (+ 30) percent capital cost for a Nine and plant is $367 million with an estimated $103 million per year operating cost. The study indicates that low-grade domestic laterite may he processed with marginal profit- ability.

Jan 1, 1982

By S. J. Schatzel, W. P. Diamond

High methane emissions originating from the active face areas and from the fractured formations overlying and underlying the mined coalbed can adversely affect both safety and productivity in underground coal mines. Since ventilation alone may not be sufficient to control the methane levels in the longwall mining environment, gob gas ventholes have become a standard supplementary methane control option in many mines. As mines progress into deeper and gassier coalbeds, or as longwall panel size increases, ventilation and gob gas ventholes together may not be sufficient to maintain methane levels within statutory limits. To decrease the risk associated with methane emissions under these circumstances, in-seam horizontal methane drainage is often used to reduce the gas content of the coalbed prior to mining. Horizontal methane drainage borehole completion designs, drilling strategies, and degasification lead times may need to be adjusted for site-specific conditions due to mine design, geology, and the gas content of the coalbed. This study investigates different horizontal methane drainage borehole patterns, borehole lengths, and degasification times prior to and during panel extraction to evaluate their effectiveness in reducing methane emissions using a "dynamic" 3D reservoir modeling of a 38 1-m wide longwall panel operating in the Pittsburgh coalbed. Results of this study showed that dual and tri-lateral boreholes are more effective in decreasing emissions and in shielding the entries compared to fewer shorter, cross-panel, horizontal boreholes parallel to the longwall face. Modeling results showed that after 12 months of pre-mining methane drainage, the average longwall face emission rates can be reduced by as much as 10.3 m3/min and 6.8 m3/min using tri- and dual-lateral boreholes, respectively. It was also shown that if pre-mining methane drainage time is short, it is important to continue methane drainage during the panel extraction to maximize reductions in longwall face emissions since additional face emission reductions achieved during this period can be comparable to pre-mining degasification.

By David L. Shuck

This report was prepared for the Bureau of Mines to describe the current methods of design, construction, and development of wells for in situ leaching of uranium. The discussion includes the alternatives for well design drilling equipment and fluids, grout formulation and emplacement, well integrity testing and repair, and well development and stimulation. Current practice in these areas was determined through interviews with eight operators of commercial scale in situ facilities and is also discussed. Based on this information plus the authors&apos; experience, recommendations are made regarding well design, construction, and development tor in situ leaching.

Jan 1, 1982

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.&apos;s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

By Raja V. Ramani

The potential usefulnuss of reclaimed surface-mined land has received much attention in recent times. This attention is partially due to the establishment of federal environmental reclamation standards but concern for achieving better land uses has also been shown by interested members of the mining industry. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U. S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, a 430-acre surface mine in Clear-field County, Pennsylvania has been studied. Established site planning principles have been applied to the case study site including formation of a data base, development of alternate land use plans, and evaluation of the economic, environmental, and social impacts of the land use alternatives. Key factors affecting site realization have been identified along with positive suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By Margaret R. Egan

A series of experiments were undertaken by the Bureau of Mines to determine the emission products of several types of conveyor belting and other combustible materials found in mines. These experiments were conducted under intermediate-scale, simulated mine conditions to determine smoke characteristics and gas concentrations. From these determinations, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. Three types of belts were investigated: chloroprene, also known as neoprene (NP); polyvinyl chloride (PVC); and styrene-butadiene rubber (SBR). The belts were designated as ignitable or self-extinguishing depending on the length of the burning time and the subsequent combustion products. Under these experimental conditions, the SBR belts were the easiest to ignite. The PVC and NP belts tended to self- extinguish within a few minutes after ignition, but were still capable of maintaining a brief flaming period. These conveyor belt combustion results are compared with previous analyses of wood, transformer fluid, and coal fires. Together they form a data base by which findings from future experiments with other mine combustibles can be compared.

Jan 1, 1988