Search Documents

By Will H. Coghill

Titanium is a well-known component of bauxite ores, sometimes occurring in sufficient quantity to mace its recovery worth considering. This question has been raised by some of the companies lixiviating bauxite ores. At the East St. Louis plant of the Aluminum Ore Co., a subsidiary of the Aluminum Co. of America, the waste sludge discharged daily contains over 75,000 pounds of Ti02. The sludge is all through 20-mesh, and a large proportion is slime. A supple of the waste was deslimed so that a gravity-concentration test of the "sand" could be made. The Aluminum Ore Co. cooperated in the work and made the chemical determinations In order to anticipate the results of table concentration a series of specific gravity fractions (float-and-sink) was made with heavy liquids. Acetylene tetrabromide was used for a density of 2.95, methylene iodide for 3.33, and thallium formate for 3.78, and the double salt of thallium formate-malonate made the separation at slimed sample appears in Table 1.

Jan 1, 1928

By Lloyd Williams

1. This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By J. F. McIlwain

Cobalt-base hardfacing alloys used for wear resistance consist almost entirely of metals largely imported into the United States. As part of an overall research program to help alleviate this foreign dependency, the Bureau of Mines has been investigating an iron-base alloy system as a potential replacement for cobalt-base alloys for some uses. To ascertain the melting ranges, thermal analyses were made of cast heats of alloys containing, in weight percent, 59-61 Fe, 16-19 Cr, 8-9 Ni, 1 Mn, 1 W, 1 Mo, 0.5 Cb, 0.6 Si, 0.3 C, and 0-12 stoichiometric TiB2. Powder alloys within this range of composition, prepared by mechanical alloying, were sized and applied to mild steel test coupons by nontrans-ferred-arc plasma spraying. The resulting thin coatings were >95 pet dense, with bond strengths of 35 MPa and hardness of 400 to 840 DPH. Abrasive and adhesive wear test data were compared to those of a plasma-sprayed cobalt-base alloy. A range of boride contents resulting in most promising properties was determined for further research.

Jan 1, 1985

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By Matthew J. Sheridan

The Bureau of Mines study described in this report was conducted in the Denver, Colo., area (1) to summarize existing conservation practices as related to the most beneficial utilization of deposits of sand and gravel; (2) to identify the conflicting positions of the aggregate producer, the mineral owner, nearby residents, and local government officials responsible for determining land status and for issuing operating permits; and (3) to show the need for planning in Denver and in other expanding communities toward obtaining the benefits of conservation of our rapidly dwindling mineral resources. In order to determine the effects of urbanization on the Denver aggregate industry, interviews were held with owners of sand and gravel operations, with producers of concrete and bituminous pavement, with city and county planning and zoning personnel, and with representatives of various interested organizations. The conservation and ultimate utilization of deposits of construction raw materials near expanding urban areas can best be accomplished by long-range land-use projection and the requesite cooperation of technically advised planning and zoning administrators, government officials, mineral producers, and land developers.

Jan 1, 1967

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By P. Yant, A. C. Fieldner

"IntroductionIn its investigations relative to reducing the hazards of carbon monoxide poisoning, the Bureau of Mines recently had its attention drawn to a compound2a sold under a trade name for which claims are reported to have been made regarding its efficacy in reducing that type of poisoning in automobile garages. Accordingly, some of the product was obtained and analyzed for its power to absorb, oxidize, or destroy carbon monoxide; and the results are herein reported.Description of ""Compound"" (quoted from manufacturer's circular)While the circular does not actually state that the ""compound"" protects against carbon monoxide, the inference is therein, because each of the two following quotations is below these respective headings; ""Carbon-Monoxide Poisoning,"" and ""Chronic Gassing Among Garage Workers.""The ""compound"" holds chlorine and oxygen gases in solution with formaldehyde, which unites with the hydrogen to form hydrochloric acid., giving an over-supply of oxygen which burns up carbon just as a piece of wood is burned in the fire. The formaldehyde in the composition of the ""compound"" is a great affinity for ammonia and hydrogen sulphide."

Apr 1, 1924

Commodities statistics and other information are available through the following three systems: Internet Access: To access the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, environmental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By Donald R. Irving

ALTHOUGH the quantity of material handled at metal and nonmetal mines in the United States in 1962 was 2.7 billion tons, the same as in 1961, a larger proportion was waste. At metal mines, crude ore production declined 1 million tons and waste output rose more than 18 million tons; at nonmetal mines crude ore production declined 6 million tons and waste output rose 36 million tons. Copper and iron ore producers increased their share of crude ore and material handled from about three-fourths to four-fifths of the national metals total, and sand and gravel and stone producers in-creased their share of the nonmetals total, also from three-fourths to four-fifths. Six States-Arizona, California, Florida, Michigan, Minnesota, and Utah-each handled more than 100 million tons of ore and waste, and together they accounted for 43 percent of the U.S. total. When the large-volume construction materials (sand and gravel and stone) were excluded from the totals, four States-Arizona, Florida, Minnesota, and Utah-supplied over half of the material handled.

Jan 1, 1963

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By John W. Kopp

A major concern with blasting at surface mines is generation of ground vibrations and airblast and their effects on nearby residences. This Bureau of Mines report looks at the use of millisecond delays in blast design and their effect on the resulting ground vibrations and airblast. A total of 52 production blasts were instrumented and monitored at a surface coal mine in southern Indiana. Arrays of seismographs were used to gather time histories of vibrations and airblast. The data were analyzed for peak values of vibration and airblast and for frequency con-tent. Various delay intervals were used within and between rows of blastholes. Delay intervals within rows were 17 and 42 ms, and those between rows ranged from 30 to 100 msj these intervals are equivalent to 0.5 and 1.3 ms/ft within rows and 1.2 to 4.3 ms/ft between rows. Sub-sonic delay intervals within rows reduced airblast by 6 dB. Large delay intervals between rows reduced the amplitude of ground vibrations; their frequency depended primarily upon the geology of the mine site.

Jan 1, 1986

By Sathit Tandanand

This report presents a Bureau of Mines study on the time-dependent behavior of coal measure rocks for future implementation in stability analysis and safety evaluation of in-mine rock structures. This initial study focused on moisture adsorption rate and strength degradation of shales in Pennsylvanian coal-bearing strata in the Illinois Basin. A reaction of clay minerals in Illinois shales with atmospheric water vapor was hypothesized as the adsorption and strength degradation mechanism. Part of energy exchange between shales and the environment was attributed to a free energy controlled by pore pressure of the rock and partial pressure in the environment. The relationships between adsorption versus time and strength degradation versus moisture content were derived and correlated with the experimental data. Partial saturation at various levels of relative humidity occurs within approximately 2 weeks at room temperature. The strength of shales tested decreases linearly with increasing moisture content. When the moisture exceeds 7 pct of the dry weight, these Illinois shales become unstable. To this end, the moisture content is a good predictor of rock strength for shales.

Jan 1, 1987

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

By Frederick K. Allgaier

This is the first in a series of progress reports on the longwall subsidence research program at the Bureau of Mines Denver Research Center. As part of this program, the Bureau and the Utah Power and Light Co. are cooperating on a study conducted at the Deer Creek Mine, which is directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. A monitoring network has been established at the Deer Creek Mine to measure subsidence over four adjacent longwall panels. To date, two panels have been mined. Subsidence began as the first panel was mined and continued for 1 year following completion of the panel, during which time the adjacent panel was mined" A maximum of 2.7 feet of subsidence occurred over the two longwall panels mined at a depth of 1,500 feet. Because of the length of time that subsidence continued after mining, the final subsidence profiles and angle of draw have not yet been determined.

Jan 1, 1982

By W. M. Dressel

Over 2 million tons of steel furnace dust containing approximately 100,000 tons of zinc and 10,000 tons of lead are produced each year. Recycling of the dusts would conserve mineral resources, lessen land area requirements for disposal, decrease pollution problems, and aid in solving our balance of payment problem. Steelmaking dusts can be pelletized and thermally treated to remove lead and zinc and to reduce the iron oxide to form metallized pellets. In laboratory tests more than 99 pct of the zinc and 85 pct of the lead was volatilized from the dust by roasting at 1,000° C in carbon monoxide. The volatilized material can be collected and treated further for lead and zinc recovery. Reduction and volatilization of over 95 pct of the zinc and most of the lead was achieved by roasting self-reducing mixtures of steel furnace dusts and high carbon steelmaking wastes in an inert atmosphere at 1,100° C. Over 80 pct of the iron in the resulting pellets was metallized.

Jan 1, 1974

By E. O. Bennett

Various methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of tests show that the "shut-in pressure-drop" method described by Rawlins2 is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rate of leakage from the fall in pressure and change in temperature determined by the "shut-in pressure-drop" method of testing. METHOD OF MEASURING PRESSURE DROP The gas is "shut in" the line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The change in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.

Jan 1, 1926

By P. G. Barnard

Losses of alloying metals in furnace flue dusts, grinding swarfs, and mill scale produced during the manufacture of stainless steel are substantial. About 25 million lb Cr, 8.7 million lb Ni, and 150,000 lb Mo and other critical metals can be made available annually for recycling by a process developed by the Bureau of Mines. Stainless steel wastes pelletized with a portland cement binder were reduced in a small electric-arc furnace by a two-stage process to produce a recyclable alloy containing Cr, Ni, Mn, and Fe. The initial reduction was with carbon; the second, with ferrosilicon. Results are compared with previously reported laboratory induction melting tests. A 2,000-lb demonstration test of the process in a commercial electric-arc furnace is also described. Data are also presented on three 1,500-lb tests made using various slag conditions in the electric-arc furnace. Recoveries up to 99 pct of the Fe, Cr, and Ni contents of stainless steel wastes were obtained in using the process.

Jan 1, 1977

By Dennis A. Hansen

The solubility of anhydrous aluminum chloride in solutions of titanium tetrachloride and vanadium tetrachloride was determined as part of a re-search project-by the Bureau of Mines to make a homogeneous alloy sponge of titanium, vanadium, and aluminum. Solubility curves were established using an autoclave at 75°, 100°, 125°, and 150° C. The solubility of AJC13 in TiC14 is 0.2 wt pct at 75° C; it increases to 18.3 wt pct at 150° C. The data concur with data from earlier researchers of this bi-nary system for 75° to 125° C. For the VC14-AlC13 binary system the solubility of AlC13 is 0.1 wt pct at 75° C, increasing to 1.6 wt pct at 150° C. For the TiC14-AlClrVC14 ternary system the solubility of AlC13 decreases from the values found with a pure TiC14-AlC13 system to the lower values found with a pure VC14-AlC13 system at the respective temperatures.

Jan 1, 1986

By John R. Reeves

The development of an new industry, which must prepare its marketable products at or near the source of the raw material, and ship them to a market which may cover half a nation, is more or less influenced by a number of natural and cultural conditions such as (1) location of plants with respect to a large market, (2) climatic conditions, (3) transportation facilities, (4) labor supply, and (5) water supply. An effort is made in this pager to give in detail a number of the more important of these conditions as they affect, either favorably or unfavorably, the development of the oil-shale resources of southeastern Indiana. The utilization of the New Albany formation for the production of oil will be similar to a large scale low-grade ore proposition in which the raw material can be obtained in very large quantities at a relatively low cost. It appears, therefore, in considering the value of this shale or its economic position in relation to other oil shales, tie cost of mining and preparation for the retort are of prime importance.

Jan 1, 1923

By T. T. Campbell

Although secondary recovery of lead and lead-tin alloys has been common practice in the United States during recent years, there is little published in-formation concerning recovery techniques. Available information does not cover metal recovery from wet dross skimmings. This investigation by the Bureau of Mines was undertaken to develop techniques that would allow lead-tin alloys to be recovered from wet dross skimmings containing large amounts of zinc chloride. A process was developed, on a laboratory scale, for recovering lead-tin alloys from wet solder dross skimmings. Straight water leaching, either with or without a second leaching operation carried out with a Na2C03 addition for removing chloride, produced a dross that could be smelted without further treatment. Overall recoveries averaging 92 percent of the metal values in the dross were obtained in the form of lead-tin alloys, which had an average tin content of 16 percent and lead content of 84 percent. The recovered alloy contained less than 0.02 percent zinc, as determined by both chemical and spectrographic analyses.

Jan 1, 1956