Search Documents

By William Skinner, Ishmael Quaicoe, Jonas Addai-Mensah, Ataollah Nosrati

To date, intractable ore specific operational challenges such as poor heap geotechnical stability, permeability and high acid consumption rates associated with low grade (~1 wt%) nickel (Ni) laterites still makes the adoption of heap leaching processing unattractive. This paper presents some highlights of drum agglomeration, column leaching and characterization studies undertaken to foster the understanding and knowledge of some of the desirable product attributes of -2 mm and -15 mm, low grade saprolitic (SAP) and goethitic (G) Ni laterite feed ores and their blends (SAP/G). For column leaching, 5-40 mm agglomerate beds were continuously irrigated with 200 g/dm3 H2SO4 solution at 8.5 dm3/m2/h rate over 100 days. Ni, Co, Fe, Al and Mn extraction rates, free acid concentration, agglomerate bed slump and structural changes were determined as a function of time. The results show that at equivalent feed masses, except -15 mm G which displayed slower, pseudo-layering based behaviour, all the feeds (single and blends) displayed coalescence controlled agglomeration behaviour at varying binder dosages. Whilst the agglomerate compressive strength of the G ore was markedly higher than that of SAP ore, those of the blends were substantially similar. At fixed column leaching conditions, the Ni/Co extractions and acid consumption were higher for SAP ore whilst the agglomerate bed slump was lower than those for G ore. The bed of agglomerates produced from -2 mm G/-15 mm SAP blend was more stable than that for the -2 mm G/-2 mm SAP blend agglomerate, the latter experiencing blockage within 24 h of acid irrigation due to agglomerates breakdown. The Ni/Co extractions and acid consumption rates obtained for agglomerates of -15 mm G/-2 mm SAP blend were lower than expected based on the ratios of the SAP and G ores within the blend composition. The findings suggest that judicious saprolitic and limonitic ores’ blending could reduce acid consumption rate, improve the agglomerate bed robustness and enhance bed percolation behaviour under prolonged acid irrigation periods during heap leaching of lateritic ores of variable mineralogy.

Jan 1, 2014

By B. H. Zhao

A low grade Pt-Pd ores, with 1g/t Pt and 0.13g/t Pd, and 8.70% Fe and 2.50% P2O5 is experimented to recover of Pt and Pd. The flowsheet is proposed which consists of Pt-Pd selective flotation, apatite flotation from tailings of Pt-Pd flotation, magnetic separation of magnetite from apatite flotation tailing. With butyl xanthate, N-ally group-O-isobuturyl-thioanimoformate and Sodium y-89 xanthate as collectors, sodium silicate as depressant, and sodium carbonate as pH regulator, a concentrate, assaying 324.52 g/t Pt and 45.62 g/t Pd, is obtained with recoveries of 87.23% Pt and 76.89% Pd from surface ore. A concentrate, assaying 1693.53 g/t Pt and 64.12 g/t Pd, is obtained with recoveries of 88.54% Pt and 83.78% Pd from primary ore. At same time, A iron concentrate assaying 64.12% Fe with a recovery of 24.94%, and a apatite concentrate assying 30.32% P2O5 with a recovery of 80.12% are obtained.

Jan 1, 2014

By Nicolus Rotich, Ritva Tuunila, Louhi-Kultanen. Marjatta

Most minerals, their ores, and gangue require sorting in order to maximize the recovery of the primary product during concentration. Gravity separation though old, is not obsolete and is continually playing an important role in mineral processing and many other industries, especially where plant energy efficiency is of concern. Screen designs e.g. material of construction, deck angle of inclination, the feed throughput, and physical as well as chemical properties of the particles, are critical factors to consider when using gravity for solid separation. Solids loading and screen geometry are significant, and easily manipulated operational parameters that affect both the screening rate and efficiency to a large extent. In this paper we applied nonlinear least squares optimization technique, and response surface methodology first, to assess the significance of the two factors, and secondly to select the best mathematical models that optimize both capacity and efficiency of the screening process. Initial experiments and confirmation tests were conducted on a prototype screen of 846.51cm2 effective area, (2100 cm2 total area). For glass beads of sizes 0.75-3mm, with feed loads of 10g up to 160g, and inclination angles from 5-20o, a maximum efficiency of 66.7%, and a screening rate of 22g/s was achieved with a screen loading of 86.5g, and an inclination angle of 12.43o. These results were then subjected to nonlinear least squares optimization, in which afterwards an optimum theoretical efficiency of 72% and screening rate of 31.2g/s were achieved at a loading of up to 104g. There was excellent performance at angles 12.5=?=17.5, but poor at the angles outside this range. The screening efficiency did not seem to respond significantly to changes in screen loading. Confirmation tests conducted at selected optimum parameters achieved an efficiency of 72.1% (at 17.5o with 88g load), and a rate of 27g/s at 16.5o with 104g.

Jan 1, 2014

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By H. Kasaini

Batch wise adsorption tests for platinum (Pt) on the surface of activated carbon pellets (Norit RO 0.8 BET surface area 1100 mg/g) were carried out in mixed chloride solution. The purpose of this study was to assess and compare the adsorption performance of amine-treated activated carbons (AACs) and native activated carbons (NACs) in terms of adsorption capacity and selectivity. The effect of pH and temperature on adsorption capacity and selectivity was established. The amine- treated ACs were prepared by anchoring the amino groups (butyl amines) on the surface of AC pellets in aqueous media and the UV-Vis was used to determine the amount of amine sequestered from solution by ACs. The dosage of butyl amine on the surface of ACs averaged 0.15 g/g, carbon. The adsorption mechanism was described by the ionization and complexation model whereby interaction between the protonated AAC surface and the anionic chlorocomplex ions (PtCl5 [H2O]-, PtCl62-) proceeded by either electrostatic attraction or/and by covalent bonding [(NH3)2PtCl6 or (CH2COO)2PtCl6]. By comparison, the adsorption capacities of Pt on amine-treated ACs and native ACs were 53.8 mg/g and 33.03 mg/g, respectively which highlight the benefits of anchoring functional molecules on ACs. The selectivity of AACs was influenced by solution pH. Pt adsorbed selectively on the surface of amine-treated ACs at pH<1.5. The highest separation factor that was recoded pertained to Pt and Fe species (ßPt/Fe = 90) then followed by Pt and Ni species (ßPt/Ni = 30) or Pt and Cu species (ßPt/Cu = 15). The lowest separation factor was recorded for Pt and Cr ions (ßPt/N= 5). Adsorption kinetics of Pt on amine-treated AC surfaces, according to the first and second order reactions, were investigated and results showed that rates were in the order 10= 5). -4 min-1 and 102 g?min/mg, respectively. The pseudo 1st order kinetics predicted the adsorption capacity of 51.81 mg/g which was almost similar to the experimental value (53.8 mg/g) while the second order rate equation predicted Pt adsorption capacity of 40.1 mg/g. Both The Langmuir and Toth isotherm fitted the Pt adsorption at pH < 1.0. The Freundlich isotherm tended to underestimate the adsorption capacity of AACs.

Jan 1, 2014

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By N. D. Dementieva

Based on lab and pilot-plant tests to recover gold, silver and lead of a Russian deposit, a collective and flotation concentration flow sheet with lead and sulfide concentrates was proposed. The type of the deposit is gold-sulfide-quartz-bearing. The recovery of gold, silver, and lead to a lead concentrate was 47.4%, 68.1% and 70.7%, respectively. The grade of gold and silver grade was 170 g/t and 372 g/t, respectively. The mass percent of lead, zinc and arsenic mass percent was 41.7%, 0.34% and 0.63%, respectively. The recovery of gold and silver recovery to a sulfide concentrate was 50.1% and 28.8% at the grade of gold 20.5 g/t and silver 66.2 g/t. Sulfide concentrate with arsenic mass percent ~3% was biooxidised followed by CIL and obtaining metal at the site as well as zinc concentrate from bioleaching solutions with zinc mass percent 45% at its 64% recovery. The total gold and silver recovery using a developed technology with the account of their treatment at a polymetallic plant was 92.2% and 93.7%, respectively.

Sep 1, 2012

By D. Endara, E. De la Torre, S. Echeverria

"The study was conducted with the sulfide mineral from the province of Zamora Chinchipe. It was characterized physical, chemical and mineralogical, obtaining between its main results a copper concentration of head ore of 0,58 %. The mineral was homogenized and taken to direct closed circuit: rollers mill - vibratory sieve (mesh # 16). Flotation was carried out in two stages: the collective and selective where in each one were performed 6 water recirculation as suggested by the technique used to relate information of a batch flotation to a continuous circuit called cyclic flotation tests (LCT). In the collective flotation (bulk) 2 Kg of mineral were grinded with 10 Kg of balls for 30 minutes and 62.5% of solids, the pulp was taken to the flotation process with solids percentages of 33.3% and pH 7, it was conditioned with 45 g / t of KAX 1%, 50 g/t of Aerofloat 208 and 20 g /t of Pine oil. The concentrate and tailings bulk obtained were filtered separately for the recovery of water and it was recirculated to the next grinding of 2kg mineral. In the selective flotation 1Kg of bulk concentrate was carried to regrind for 40 min, 62.5% percent of solids, 10 g of lime and 5 g of tannin FLOATAN T5, the pulp was taken to the roughing-collection-refining flotation circuit controlling the pH between 10.5 and 11 where conditioning (60 g/t of Aerofloat 208 and 30 g/t of Pine oil) and adding lime to the circuit and FLOATAN according to the procedure. The four fractions obtained from the circuit were filtered; the water was recirculated to the regrind process of the bulk concentrate. In the collective flotation process tends to stability in the fourth recirculating water to obtain a copper content of 4.5% and a recovery of 87%, recirculated water represents 69.8% of all water used in the 6 recycles. In the selective flotation circuit the fifth recirculating of water is the optimal where obtaining a copper content of 13% and a recovery of 72%, recirculated water in the selective flotation circuit represents 95% of the total water used in the 6 recycles."

Jan 1, 2018

By M. S. Eygi

This study covers the investigations based on the electrokinetic and rheological properties to explain the interactions between kaolin minerals and commercially available polyelectrolyte in anionic character. Additional adsorption test were also conducted to support the interaction mechanism. Adsorption tests showed that adsorption densities decrease by increasing the solid content. In-creasing the solids contents from 1% to 30% by weight resulted in the decrease on adsorption from 2.14 mg/g to 1.85 mg/g. Because of its difficulty, the solids ratio at 70% was not studied. However, following to trend of the curve plotted adsorption density-solid ratio, an estimation was made and adsorption density at 70% solid content was extracted from the curve as 1.75~1.80 mg/g. The electrokinetic studies pointed out that the presence of polyelectrolyte increase the zeta potential of kaolin from 40 mV to 60 mV which is reasonable conditions to disperse and stabilize the kaolin slurry and lower the viscosity. When these result of the different tests are combined and considered together, 2 mg/g polyelectrolyte concentration was noted as optimal concentration where adsorption density, viscosity and zeta potential of the slurries give maxima and remain constant after this concentration.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By Ersin Yazici, Ahmet Bas, Haci Deveci

Pregnant leach solutions from waste of printed circuit boards (WPCB) leaching contain many impurity metals (Fe in particular) at significant levels. These impurities should be reduced to acceptable levels to avoid problems in downstream recovery processes e.g., low current efficiencies in electro-winning of copper from sulfate solutions in the presence of ferric. In this study, removal of iron in the form of goethite from synthetic (30 g/L Cu2+ and 1 M SO42-) and real leach solutions of WPCB was studied in some detail. The influences of initial concentration of iron (1-4.5 g/L Fe3+), pH (2.5-4.0), temperature (80-90°C) and seeding (23.5 g/L) were investigated over a period of 4 h. A significant increase in the iron precipitation was observed (i.e., from 68% to 96% over 4 h) with rising the pH from 2.5 to 4.0. The addition of seeds had also increased the removal rate over 4 h albeit to a limited extent i.e., from 96% to 99%. For the real leach solutions of sulfate (H2SO4-H2O2) and sulfate/chloride leaching (H2SO4-CuSO4-NaCl), precipitation of iron was found to be 63-73% (pH 2.5) and 93-98% (pH 4.0), respectively. The precipitates were further characterised by SEM-EDS analysis which showed the presence of copper (1-25%) in the precipitates indicating significant copper co-precipitation from the solution. These copper losses can be attributed to the formation of copper compounds such as anthlerite and brochantite within the range of pH (2.5-4.0) tested. This study showed that iron can be readily removed from synthetic/real leach solutions of WPCBs to a large extent (=93%) at the expense of high copper losses particularly at pH 4.0.

Jan 1, 2014

By Y. Lin

It is difficult to remove arsenic and bismuth from antimony in the process of crude electro refining. The electro refining of antimony has been studied using ammonium fluoride-antimony sulphate electrolyte system. The Influence of temperature, current density and additives on arsenic and bismuth removal from crude antimony has been investigated in this paper. Optimum process parameters, namely, temperature of 25?, current density of 400A/m2, distance between anode and cathode of 50mm, electrolytic period of 24 hours, oxalic acid dosage of 10g/L and complexon III dosage of 0.2 g/L have been ascertained.

Jan 1, 2014

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

By Arman Ehsani, Ersin Yazici, Haci Deveci

The downstream treatment of chloride leach solutions of WPCB for recovery of base and precious metals by a combination of adsorption and precipitation processes were carried out. A synthetic leach solution (1 M HCl, 116.5 g/L Cl-, 30 g/L Cu2+, 2.5 g/L Fe3+, 5 mg/L Au3+, 10 mg/L Ag+ and 20 mg/L Pd2+), which was prepared based on the composition of the pregnant leach solution obtained in the previous study was used in the tests. The leach solution was initially subjected to activated carbon (AC) adsorption (20 g/L AC, 80°C) in which gold was selectively recovered over silver and palladium i.e., 88% Au recovery at 0.5 h (92% at 3.5 h) compared with only 3-6% for Ag/Pd. Copper and iron were also observed to adsorb on AC as indicated by 1.4% and 17% decline, in their respective concentrations. Following the adsorption and filtration stage, metallic copper was added into the gold-barren solution to allow reduction of Cu2+ to Cu+, and to cement Pd on metallic copper. Over the mixing period (1 h), 93% of the Pd was recovered while only 1.4% of silver was cemented onto metallic copper. Subsequently, the leach solution was gradually neutralised by NaOH to pH 4, 7.5 and 9.5 for the precipitation of copper as cuprite (Cu2O). It was found that 41% and 46% of Cu and Ag, respectively, were precipitated at pH 4 at which iron was almost totally (99.8%) removed from solution. Precipitation of copper and silver was increased further at high pHs. At pH 9.5, cumulative recoveries for copper and silver were 91% and 85%, respectively. XRD analysis of the precipitates confirmed the presence of cupric copper oxides/hydroxides and revealed that copper losses occurred at pH 4 was due to the undesired presence of cupric copper in the solution.

Jan 1, 2014

By N. S. Voiloshnikova

Large-scale continuous ?Resin-In-Pulp? process tests were conducted at Irgiredmet. The object for testing was the sample of oxidized gold ore from one of Siberian deposit. Weak-base ion ex-change resin PuroGold was used as adsorbent. The duration of ?Resin-In-Pulp? tests was sufficient for a completing of three cycles ?Adsorption/Elution?. Gold in feed was 0.95 mg/L. Gold in solid phase of adsorption tails? 0.065 g/t. Gold in liquid phase of adsorption tails? 0.026 mg/L. Total gold in adsorption tails ?0.11 g/t. Gold recovery ?94.3 %. The use of regenerated resin had practically no effect on gold losses with adsorption tails. Alkaline cyanide solution (NaCN-20g/L, NaOH- 5g/L) was used as eluent for gold elution from loaded resin. Elution temperature ?60 °C. Number of eluent bed volumes passed ?10. Loaded resin analysis was following (g/ton): Au? 1700~1250; Ag? 400~460; Cu? 250~450; Zn? 5100~9600; Fe? 860~1200. Elution efficiency: Au? 95.3%~97.8%; Ag? 84.0%~88.0%; Cu? 84.0%~88.0%; Zn? 97.0%~99.0%. Although high zinc resin loading was shown zinc was eluted efficiently. The adsorption properties of fresh PuroGold resin, PuroGold resin after 3 cycle ?Adsorp-tion-Elution?cycles in comparison with AM-2B resin were tested. It was shown from adsorption isotherms that selectivity of PuroGold resin slightly less in comparison with AM-2B resin mainly due to its higher zinc adsorption properties. It was founded on base of test results that adsorption properties of PuroGold resin was practically constant during three ?Adsorption/Elution? cycles. Gold may be efficiently recovered by resin tested. There were no difficulties during gold elution from loaded resin and its regeneration. PuroGold resin was recommended for industrial use in RIP process. Process design criteria were developed and plant design is on progress at the moment.

Jan 1, 2014

By Junwei Han, Wenhua Li, Wenqing Qin, Fen Jiao, Wei Liu, Jiaqi Xu

"A novel technology was developed to study the process of recycling copper from waste printed circuit boards (WPCBs), which are the main source of metal production in the next decades. The chemical compositions of the WPCBs were investigated. The results indicated that the PCB powder was mainly composed of copper (38.5 wt.%), iron, aluminum, and non-metallic materials. Copper is mainly in the form of Cu and is the most valuable metal for the recycle of WPCBs. The concentrated WPCBs powder, obtained by the mechanical process, were pressed as the anode, which was directly electrolyzed to produce copper. The effects of H2SO4 concentration, Cu2+ concentration, current density, pole pitch, and liquid-to-solid ratio on the voltage, current efficiency, and copper extraction were investigated. The results indicated that the optimum conditions were liquid-to-solid ratio of 30 mL/g, current density of 571 A/m2, sulfuric acid concentration of 180 g/L, 50 g/L of copper ion, polar distance of 3 cm. Under the conditions, a desired current efficiency could be achieved. Meanwhile, about 95.62% Cu was recovered from the WPCBs. The experimental studies also revealed that the purity of copper obtained at the highest current efficiency was higher to 99.98%. Produced copper sheet were characterized by X-ray diffraction (XRD). XRD analysis indicated that the copper was the main phase. INTRODUCTION With the rapid development of electronic industry, more and more waste electronic and electrical equipments (WEEE) are generated every year (Fogarasi et al., 2012; Liang et al., 2013). The production of printed circuit boards (PCBs) is the base of electronic industry, because it is the essential part of all electrical and electronic equipments (Schlummer et al., 2007). As a result, a considerable amount of waste PCBs containing plenty of heavy metals have to be treated. In general, PCBs contain about 28% metals that are abundant non-ferrous metals such as Cu, Pb, and Sn. Printed circuit boards can be considered as a secondary resource for recycling rather than wasting. The contents of gold and silver respectively reach 80 g/t and 3300 g/t, which are much higher than that of primary ores. Copper is the main metal of PCB and its content is as high as 26.8% ( Zhang et al., 2009)."

Jan 1, 2018

By Y. M. Zhao

The dry coal preparation technology based on air dense medium fluidized bed is an innovative dry highly efficient technology of coal by introducing fluidization technology into beneficiation.. A modularized 40-60 tones/hr system (KZX-40) with an air dense medium fluidized bed separator was established. The construction cost of the modularized system is only 1/3 of the traditional wet heavy-medium coal preparation plant construction cost with the same capacity, and the consumption of dense medium can be reduced by 50%-60%. The footprint and volume of the system are decreased by 75% and by 89.81%, respectively. These facts show the improved intensity, efficiency and economy of modularized coal preparation technique. The modularized KZX-40 system can be used to separated 50-6 mm coal over a separation density range of 1.3-2.2g/cm3 depending on the variation of <1mm fine coal content. The separation efficiency of the system was investigated at low and high separation densities by float-sink experiments. The partition curve of the products at low separation density shows that the separation density (d) is 1.33g/cm3, and the probable error (E) value is 0.05g/cm3. Using 50-6mm coal with an ash content of 55.35% as feedstock, at a high separation density of 1.61g/cm3, the clean coal with an ash content of 14.67% and the tailing with an ash content of 71.26% are produced with an E value of 0.06g/cm3. It is clear that the modularized KZX-40 system is suitable for separating 50-6mm coal effectively. During the dry coal preparation process, the dust is removed by the bag collector and recycled back into the separator. So the system has the advantages to work without environmental pollution and water. The modularized system greatly reduces the construction and operating costs and decreases the area and volume required, compared with wet dense medium system. The system is applicable to the coals located in arid regions and also to the coals that tend to slime during wet separation. Keywords: modularized, KZX-40, fluidized bed, beneficiation

Sep 1, 2012