Search Documents

By J. Jara

Oxygen, ozone and air were evaluated in the oxidation of ferrous iron in the presence of hydrochloric acid ranging from 0.1 to 4 M HC1. Stoichiometric coefficients were determined through mass balances of gases and ferrous titration. The molar ratio ferrous to ozone increases from two at 0.1 M HC1 concentration to six at 4 M HC1. For oxygen the same ratio is constant and equal to 2 and it is in agreement with other works. The stoichiometric coefficient of hydrogen ion was not defined due to the effect of hydrolysis of ferrous and in particular ferric ion on measuring acid concentration by titration with sodium hydroxide. Agitation, gas flow and pressure contribute in the utilization of gas. A technique to compare the gas efficiency at several conditions is discussed and it is based on the relationship between oxygen and ferric during time. There is a strong compromise between gas efficiency and ferrous conversion. Oxygen efficiency decreased with time due to ferrous depletion. The gas efficiency ranged from 3 % (low level of agitation) producing 25 g Fe(III)/h to 12 % at 1000 rpm with 60 g Fe(III)/h converted. At 405 kPa absolute the oxygen efficiency was in the range of 80 % producing 300 g Fe(III)/h. The replacement of chlorine with oxygen to enrich molybdenite concentrates by reducing copper to less than 0.2 % was evaluated. Oxygen can be employed in batch or continuous operation and it can treat molybdenite concentrates with high variation of copper content. The dissolution rate is mainly controlled by oxygen addition in which utilization of oxygen plays an important role. Improvement on safety and environmental conditions is feasible by using oxygen instead of chlorine gas. The economics indicate good opportunities to implement oxygen without significant modifications to the actual circuit and enough benefit when oxygen is well used.

Jan 1, 2007

By Jamal Jafari, Abbas Sam

"The concentration of the fourth production line at Golgohar includes 66% iron with Blaine number of 500 cm2/g. For pelletizing process, the feed iron grade should be greater than 68% with minimum Blaine number of 1800 cm2/g. In this study, the low intensity magnetic Separators, particularly the feed particle size distribution of LIMS were considered. The feed particle size distribution of the separators was optimized to prepare an appropriate concentrate (as mill pelletizing feed). The samples were performed from the LIMS feed and after grinding, four d80 (64, 103, 132, and 15 3µm) were prepared. Then, laboratory magnetic separation experiments were conducted on these samples. The best results obtained using d80 of 132µm. In this particle fraction, the iron grade and Blaine number were 70.3% and 1571 cm2/g, respectively. Therefore, it seems necessary to include a grinding and classification systems before LIMS stage. According to the presence of a high amount of -132 µm particles in the initial feed, an inverse closed circuit was selected. The hydrocyclone was designed in three units as the classification system with 62 cm (diameter), 22 cm (overflow outlet) and 11 cm (apex diameter). By simulation of hydrocyclone with USIMPAC software, the size distribution of underflow was determined. Based on these results, a ball mill with dimensions of 6.7 m (length) and 5 m (diameter) was designed as grinding system.INTRODUCTIONGole-Gohar iron ore concentration plant No.4 (Polycom Plant) in Gole-Gohar Industrial and Mining Complex was installed to increase production capacity as well as treating the circulating load from AG and SAG mills of the main concentration plant of the complex. The load from the mine is crushed using jaw and cone crushers. The crushed ore is then combined with the circulated load and the combination is then grounded using HPGR and ball mills respectively.After comminution, there is a magnetic separation plant which includes a medium intensity magnetic separator (MIMS) followed by three low intensity magnetic separators (LIMS). Final concentrate dewatering is done using three belt filters. After the primary magnetic separation, the ore is upgraded to 62% Fe content and final concentrate which is the product of LIMS has 66% Fe content."

Jan 1, 2016

By Pierre Beaudoin

"This paper deals with the repairs made on two damaged mills. It investigates briefly the causes of the damage, explain its nature and the design of the repair. It explains the detrimental effect on operation and the solutions implemented to reduce them. Finally, to review the follow-up required for such repairs. LOCATIONThe Holt McDermott Mine is located 75 kilometers Northeast of Kirkland Lake and 30 kilometres west of the Quebec border in Northeastern Ontario. The town of Kirkland Lake is located approximately 500 kilometres north of Toronto. HISTORYThe discovery of gold in Holloway Township dates back to early 1920. In 1984 Barrick Resources, which amalgamated with Camflo Mines, acquired more claims on the property and initiated an extensive drilling program. By 1985, the drills indicated reserve increased to 2,500,000 tonnes grading 6.8 g/mt. In 1986 a production decision was made and in 1988 the mine was officially opened.As of December 31, 1998, 4,691,507 tonnes grading 5,66 g/tonnes have been milled from 4 ore-bodies. The mill started up in June 1988."

Jan 1, 2001

By J. J. Bouillon

"Located in the northwestern portion of the Abitibi greenstone belt, Les Mines Selbaie is a copper-zinc (silver and gold) producer. Felsic tuffs host three are zones. Composed of sulphide veins and breccias, they are not exhalative massive sulphide deposits, except, probably, for the massive pyrite (fragments and lenses) localized close to the top of the volcanic sequence.The total of all (mineable and mined) ore in the three zones presently outlined on the property, is of the order of 29.9 x 106 tonnes with average grade of 0.63 g/t Au, 37.02 g/t Ag, 1.21% Cu, 1.91% Zn.The ore reserve calculations and the daily production procedures are computerized to various degrees. The data handling process is highly computerized.Various geophysical methods are, and have in the past, been successfully used on the property. The ""mise-à-la-masse"" surveys were used to perform the geological interpretation of an underground deposit (A-2 zone). Presently the PULSE-EM surveys are performed in all surface and underground exploration drill holes."

Jan 1, 1990

By R. V. Kumar, F. Tailoka

In order to use ZnO laden dust as a possible desulphurization reagent, it is important to evaluate thermodynamics of the Zn-O-S system. At temperatures greater than 1450 K, there is an uncertainty in the thermodynamic data for the reaction of zinc with sulfur to form Zinc sulfide. In this work, the standard free energy has been determined using an electrochemical cell: Pt, Mo, MoO2/YSZ/ZnO, ZnS, S02, Pt., between 1198 and 1602 K. AG° varies from -145,880 to -88,100 J (± 2500) , with a phase change to ZnS (g) by sublimation occurring between 1450 and 1460 K. This is supported by thermogravimetric analysis which shows about 80% weight loss in ZnS from 1273 to 1473 K. Feasibility reactions were also performed and confirmed that ZnS (g) is formed when ZnO reacts with FeS (1473 to 1653 K) or with Fe-Csat-S(1473-1673 K). There is therefore potential for the utilization of ZnO laden waste as an additional or alternative reagent for desulfurisation.

Jan 1, 2004

By J. T. Furey

"A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from a gold/tellurides bearing sulphide ore, and to compare the performance of column flotation to conventional ""mechanically agitated"" flotation.Tests were conducted in a 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail.The ore had an average ""as tested"" feed grade of about 5 g/t gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbragite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of 97%, but produced grades of+ 150 g/t Au. INTRODUCTIONColumn flotation is the most significant innovation that has occurred in the mineral processing industry in recent years and has become an important alternative to mechanical flotation. Column flotation has been most widely accepted and applied in cleaning service where it has frequently proven to be superior to mechanically agitated flotation. Roughing in columns has not been ignored, but early testing indicated that columns may not be capable of achieving adequate recovery and, to date, columns have not been seen as serious competitors for mechanical roughers."

Jan 1, 1990

By P. L. Li, B. X. Song, C. H. Wang, T. Wang, Z. Hu

"The treatment of an oxidized copper-gold ore by stage cyanide addition was investigated. For cyanidation, free cyanide ion concentration can be an indicator of whether there is copper dissolved in cyanide solution, and maintaining the free cyanide ion concentration lower than 1.0 g/L could be an effective way to prevent copper dissolution and reduce cyanide consumption. For that purpose, stage cyanide addition was introduced to control free cyanide ion concentration within the range from 0.8 to 1.0 g/L. Cyanidation tests results indicate that gold extraction was still acceptable at reduced cyanide consumption with a lower copper extraction. Based on the experimental study, industry application works at Beiya concentrator of Yunnan province, China were successfully conducted. When the raw ore contains 2.95 ppm Au and 0.75% Cu, by stage cyanide addition method, the gold extraction was still 93% at reduced cyanide consumption of 2135 g/t, which was only half of one addition method, and the copper extraction dropped to only 5%, which indicated that dissolution was prevented for almost 75% of the malachites.INTRODUCTIONCyanide with its competency to form a strong complex with gold, is the most preferable lixiviant for gold leaching. However, cyanidation is not inherently a selective process since many other minerals present in the ore are also readily soluble, especially the copper minerals. Muir (2011) reported that every 1% reactive copper present in the ore consumes about 30 kg/t NaCN, which can have detrimental effects on the process efficiency and economics due to high cyanide consumption, reduced gold leach rates and poor gold recovery."

Jan 1, 2016

By T. G. Joseph, M. Bolster, M. Curley

"High tirerim loading on haul trucks operating on rough ground frequently manifests as mechanical separations and rim base cracking caused by cyclic fatigue. This paper provides an understanding of the impact of high loads on rim component life and tire footprint, bulge, and deformation behaviour; and develops a maintenance planning tool to predict strain implications of high g loading for a given rim location. Loading tests and analyses were conducted for a tirerim arrangement under increasing load and internal tire pressure. Graphical models were developed, allowing higher g load extrapolation predictions for specific rim components.KEYWORDS g load, Mining, Model, Prediction, Rim, Strain, Tire bulge, Tire footprint, Ultra-class vehicleRÉSUMÉ L’application d’un chargement élevé sur le système pneu/jante de camions de transport rou¬lant sur des terrains accidentés se manifeste fréquemment par des séparations mécaniques et une fissure à la base de la jante engendrée par une fatigue cyclique. Cet article nous permet de mieux comprendre l’incidence de l’application de charges élevées sur la durée de vie des composantes de la jante ainsi que sur l’empreinte, la hernie et le comportement de déformation des pneus. Il développe également un outil de planification de l’entretien visant à prévoir l’incidence des contraintes en cas d’application d’un chargement g élevé sur un endroit donné de la jante. Des essais et des analyses de la charge ont été effectués pour un agencement pneu/jante soumis à une charge et une pression interne du pneu croissantes. Des modèles graphiques ont été développés, ce qui a permis d’établir des prédictions sur la base d’une extrapolation du chargement g plus élevé appliqué à des composantes spécifiques de la jante.MOTS CLÉS charge g, contrainte, empreinte du pneu, exploitation minière, hernie du pneu, jante, modèle, prédiction, véhicule ultralourdINTRODUCTION The purpose of this paper is to report on a proposed and trialed tire performance test based on data obtained from controlled testing that is used to predict the impact of high g loading on hauler rims and tires with greater accuracy. For example, for many years oil sand mining operations have expressed qualitative beliefs that an impact load of the magnitude experienced by a rim and tire arrangement is not detrimental to a rim as a stiff component; however, mining equipment components are subjected to cyclic loading where failure can result from repeated load/unload activity, truncating the peak region of a stress–strain response and resulting in fatigue failure at a stress value that is less than the peak value. The outcome reported by oil sand haul truck maintenance groups indicates they have realized that most high g impacts—such as those experienced by hauler tires and rims operating on poor ground conditions—can result in failure due to cyclic loading, where higher loads require fewer cycles for failure. This high-level loading and the resulting strain transmitted to the rim is evident in the results of the laboratory testing presented in this paper."

Jan 1, 2019

By D. Van Tonder

ABSTRACT The comparative economics of ion exchange and direct precipitation have been analyzed by developing indicative CAPEX/OPEX models for typical alkaline leach uranium circuits. An agitated tank ore leach application is considered, comparing resin-in-pulp and direct precipitation as recovery options. Capital and operating cost estimates are derived from rates and factors used in recent studies and projects. The analysis showed the main economic drivers to be the ore grade and resin loading. The resin loading is impacted by the prevalence of competing ions, especially chloride. At resin-in-pulp solution chloride concentrations below 3 g/L and uranium grade below 640 g/t U3O8, resin-in-pulp is more economical, whereas at chloride concentrations above 3 g/L, direct precipitation is more economical.

Jan 1, 2012

By Alan J. Wianwright

Introduction ??New world-class Upper Devonian porphyry Cu-Au system located in south Mongolia ??6.5 km NNE-trending mineralized corridor ? 4 discrete deposits ??Southern Oyu deposits: Chalcopyrite, deposits: bornite ??Hugo Dummett: Zone: Hypogene chalcocite in addition to chalcopyrite and bornite ??Total resource exceeds ~2 Gt@ >1% Cu, >0.25 g/t Au (0.6% Cu equivalent cut-off) (Ivanhoe Mines press release, 2005)

May 1, 2006

By Laszlo Imreh, Pierre Trudel, André C. Tessier

"The Siscoe gold mine is ranked as the fourth largest mine in the history of the Val d' Or mining district with a total production of 27.4 tAufrom1929 to 1949. Most of the gold mineralization occurred in quartz veins, hosted in a small (.69 km2) intrusion of altered quartz gabbro known as the Siscoe stock. The southern contact of the Siscoe stock is crosscut by a major shear zone (the ""K"" zone) trending 295/80 NE and from which gold mineralization was also exploited within the limits of the stock. Field and petrographic observations of the Siscoe stock combined with chemical analyses of major, trace and rare earth elements of the stock and its volcanic host rocks (Dubuisson Formation) suggest that:The Siscoe stock comprises four alteration facies formed from a homogeneous precursor: 1) the actinolite - Mg-chlorite facies, characterized by low FeOt,Na2O andTiO2 , and highAlp3 and MgO; 2) the albite- Fe-chlorite facies, containing high concentrations of FeOt and Nap; 3) the Mg + Fe-chloritefacies, which is transitional between the actinolite- Mg-chlorite and albite- Fe-chloritefacies; 4) the carbonate-chlorite facies, which consists of rocks that were subjected to extreme hydrothermal alteration, is spatially associated with mineralized veins and part of the K-zone. The first three facies are depleted in SiO 2, CaO and Au, and enriched in MgO, relative to fresh rocks of the Siscoe stock and the equivalent rocks of the Dubuisson Formation.Hydrothermal fluids introduced mainly along the K-zone ""channelway"" induced three types of element remobilization, resulting in the various alteration facies: 1) redistribution of elements within the stock from one facies to another (e .g., FeOt, Nap, Ti02 migrated from the actinolite- Mg-chlorite facies to the albite- F e-chlorite and Mg + Fe-chlorite facies); 2) remobilization of elements from the intrusive rocks into veins (e.g ., SiO 2 and CaO ); 3) introduction of elements by hydrothermal fluids in rocks of the Siscoe stock (e .g., Al2O3, MgO, H2O, CO2 and FeOt).The Siscoe stock and the Dubuisson Formation form part of the same tholeiitic suite. Similarly, the Bourlamaque batholith and the Val d'Or Formation belong to a single calc-alkaline suite. In view of this relationship, dissimilarities between the petrochemistry of the Siscoe stock and the Bourlamaque batholith suggest that the two intrusions are not co-magmatic.Finally, gold may have been leached from rocks of the Siscoe stock and remobilized into the quartz-carbonate mineralized veins. In order to account for the total production at the Siscoe mine, approximately 1.2 km3 of the Siscoe stock is thought to have been partially leached of its gold."

Jan 1, 1990

By Mehmet F. Tauer, Pierre Trudel

"The metamorphosed mineralized Archean Bourlamaque batholith, dated at 2710 +-54 Ma, is a homogeneous body, composed mainly of quartz diorite; it is cut by late dioritic, mafic and aplitic dykes, and contains metasomatized ultramafic xenoliths. A geochemical investigation confirms the calc-alkaline affinity of the batholith, and the REE profiles are similar (Lal Yb = 3.9 to 8.1) to those of the intermediate to felsic metavolcanic rocks at Val d'Or into which the batholith was intruded and to those of the calc-alkaline members of the Blake River Group at Rouyn.Gold distribution within the batholith is heterogeneous and anomalous. Although the background Au content of the batholith is estimated to be 3.2 ppb Au by RNAA , the estimated median gold content of the batholith is 10 pp b (with P84 =32 and PI 6=3.1 ppb), much higher than that of ""normal"" granites (I to 5 ppb A u). The gold mineralization exhibits a close relationship with shear zones (e.g. Belmoral Mine) or with diorite dykes (e.g. Sullivan, Perron and Courvan mines).The following sequence of geological events is proposed: (I) pretectonic emplacement of the batholith, which is cogenetic with its volcanic host rocks; (2) regional metam orphism and deformation with localized shearing; and (3) hydrothermal alteration and quartz veining. We conclude that: (1) the Bourlamaque batholith is a gold-enriched intrusion, and (2) the determination of average gold content may be an effective method f or distinguishing ""sterile"" intrusions from those with potentials for gold mineralization.RESUMELe batholite archéen minéralise de Bourlamaque, daté de 2710+-54 Ma, est une intrusion homogène, constituée principalement de diorite quartzique, qui a été recoupée par des dykes tardifs de diorite, d'aplite et de composition mafique. Il contient aussi des enclaves de roches ultramafiques metasomatisees. L 'étude géochimique confirme le caractère calco-alcalin du bath olite et les profits des ETR sont semblables (La/ Yb=3.9 a8.1) a ceux des volcanites intermédiaires afe tsiques de la région de Val d'Or dans lesquelles le batholite fait intrusion et à ceux des unites calco-alcalines du Groupe de Blake Ri ver a Rouyn. La distribution de Au dans le batholite est à la fois anomale et hétérogène. Bien que le bruit de fond du batholite ait été estime à 3.2 ppb A u par AANR, sa médiane a été estimée a10 ppb Au (avec P84=32 et PI6= 3.1 ppb) , ce qui est nettement plus élevé que la valeur des roches granitoides ""normales"" donnée dans la littérature (1 a 5 ppb A u). Dans la batholite, la minéralisation aurifère est intimement associée aux zones de cisaillement (e.g. mine Belmoral) au aux dykes de diorite (e.g. mines Sullivan, Perron et Courvan).La séquence des évènements géologiques suivante est proposée: (1) emplacement pre-tectonique du batholite, lequel est cogenetique avec les roches volcaniques encaissantes; (2) deformation et metamorphisme regional avec des cisaillements tectoniques locaux; et (3) altération hydrothermale et développement des veines de quartz. Nous concluons que: (1) le batho lite de Bourlamaque est une intrusion enrichie en Au; (2) la determination de la teneur en Au peu être une méthode efficace pour distinguer les intrusions stériles de celles qui possèderaient un pot entiel pour des minéralisation s aurifères."

Jan 1, 1989

By G. C. McKerrow

"Mr. G.C. McKerrow, Assistant Manager of Noranda Mines and formerly Smelter Superintendent attended the meeting to answer questions as to why smelters imposed penalties for too much zinc in a copper concentrate or too much copper in a zinc concentrate, etc.D.W. Bridges -Mattagami Lake MinesWhat limits do you set on zinc and lead in a copper concentrate?G.C. McKerrow - At Noranda, we allow 5% zinc free and charge 25 cents for every unit above that. For lead, it is 1% free and 25 cents per unit above that. Lead is a much more harmful impurity than zinc because it tends to recycle more in the smelter circuit and creates a greater health hazard in the plant.E. Thornton - Sullivan GroupWHat harm does fluorine do in the smelting process?G.C. McKerrow - Fluorine usually does not occur in harmful concentrations in non-ferrous smelters. Fluorides are present in exhaust gases in the aluminum and phosphate industries. If these fumes escape into the atmosphere, they may settle out on forage grasses in concentrations that are harmful to livestock.Thorton - Sullivan GroupI have asked this question other places and have been told that it is hard on brick linings and causes gold and silver to be lost up the stack.G.C. McKerrow - Almost any volatile constituent in a smelter charge will aid in carrying other metal values. To this extent it may be harmful.E. Thornton - Sullivan GroupMr. Tait mentioned before a smelter where they have a copper-tin ore and they pay for copper, tin, bismuth and silver but object strongly to indium in the concentrate. Why would this be?G.G. McKerrow - 1 can't see why indium would be a serious impurity. It does tend to concentrate in flu dusts and if you get enough of it you can recover it and sell it but I have never heard of anyone putting a penalty on it.Question - I once ran into a small copper mine in Peru that had cadmium in the copper concentrate but no zinc. The copper smelter charged a penalty for the cadmium. Why would this be?"

Jan 1, 1971

By S. G. Shabestari

Thermal analysis is a tool that is generally employed to predict the structure of the alloy before the actual casting is carried out. By cooling a sample of the molten alloy and recording the temperature-time curve, important solidification events may be analyzed by using the first derivative-cooling curve. In this research, strontium is added to (AS5U3G) 319 aluminum alloy and its influence on the formation of intermetallic compounds e.g. Al15(Mn,Fe)3Si2, Al2Cu, Al5Mg8Cu2Si6 formed during pre- and post-eutectic reaction have been investigated. Also any changes in solidification parameters such as temperature of Al-Si eutectic under cooling and temperatures of nucleation and growth of each phases caused by strontium addition, have been determined via the first derivative cooling curves. The effect of strontium on the formation of various intermetallic compounds has been studied by using very accurate thermal analysis equipment and the microstructures were analyzed using an optical microscope. The various phases reported in this paper were identified using Scanning Electron Microscopy (SEM) and linked to Energy Dispersive Spectroscopy (EDS). Formation of all pre- and post-eutectic phases was interpreted by comparing the phases formed in the microstructure and the reactions detected by using cooling curves. The results of this research indicate that thermal analysis technique can be used as an on-line process control in the production lines in aluminum casting industries.

Jan 1, 2004

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By F. Moraw

The use of redox fuel cells in which oxygen is replaced by other oxidants such as ferric ions can have significant advantages [1-3]. For example, the cathodic reaction rate (e.g., exchange current density) can be increased by several orders of magnitude compared to the oxygen reduction reaction, and platinum group metal (PGM) catalysts are not required. As a result of the higher aqueous solubility of the oxidant in a redox fuel cell compared to that of oxygen the rate of mass transfer (e.g., limiting current density) is greater by several orders of magnitude. The redox fuel cell can achieve high efficiencies and has other fuel cell advantages. The main issue with the redox fuel cell cathode is the regeneration of the oxidant where low conversion efficiencies are achieved even with platinum group metal (PGM) catalysts. In the work discussed here the Fe3+/Fe2+ redox fuel cell cathode is characterized over a range of electrolyte concentrations and operating conditions, and electrode materials. Cyclic voltammetry and electrochemical impedance spectroscopy are mainly used for electrochemical characterization and mechanistic determination of the cathode redox couple. Further characterization with selected compositions and materials is done in a redox fuel cell (hydrogen - Fe3+/Fe2+). The mechanism and the advantages and disadvantages of the fuel cell redox cathode are discussed with respect to other approaches and other redox couples.

Jan 1, 2005

By Anne-Marie Dagenais

Un recouvrement de type couverture à effets de barrière capillaire (CEBC) a été mis en place en 1988-1999 sur le parc à résidus de l?ancien site minier Lorraine situé au Témiscamingue. Depuis sa construction, la CEBC fait l?objet d?un programme d?auscultation et de suivi qui vise à évaluer son comportement hydrique et sa capacité à limiter le DMA. Des essais de consommation d?oxygène ponctuels ont également été réalisés sur le site afin de mesurer directement le flux d?oxygène traversant la couverture. Les résultats provenant des relevés de teneur en eau volumique et de succion, pour les années 1999 à 2001, montrent que les effets de barrière capillaire sont présents et que la couche de rétention d?eau demeure dans un état près de la saturation pour l?ensemble de la couverture. Les flux d?oxygène calculés à partir des mesures mensuelles sont en général inférieurs à 10 g/m2an, soit en deçà des valeurs de design de 20 à 40 g/m2an. Les essais de consommation d?oxygène réalisés sur la CEBC donnent également des flux d?oxygène du même ordre de grandeur. Les résultats obtenus de ces différentes méthodes d?évaluation concordent, et ils confirment l?efficacité de la CEBC à inhiber le flux d?oxygène et à contrôler le DMA.

Nov 1, 2002

By R. Lasmanis

"Washington State's diverse geological setting is reflected by its several types of porphyry Cu-Mo deposits. All are associated with calc-alkaline intrusions, and they range in age from Jurassic to Miocene.The largest is the Mount Tolman Mo-Cu deposit located in the Omineca Belt. It contains 2.18 billion tonnes of material averaging 0.093% MoS2 and 0.09% Cu. There are intermediate-size Mesozoic deposits in the Intermontane Belt. The Cascade volcanic arc hosts small- to medium-Tertiary deposits. Among these, of particular interest is the Sunrise breccia pipe, which has been explored over a vertical distance of 1000 m. It contains reserves of 64.6 million tonnes averaging 0.319% Cu and 0.071% MoS2 with significant tungsten values. The Glacier Peak deposits have potential resources of 1.7 billion tonnes averaging 0.334% Cu and more than 0.015% MoS2 and also contain tungsten. The Margaret deposit can be classified as a porphyry Cu-Au type; it has reserves of 200 million tonnes averaging 0.434% Cu, 0.0175% MoS2> 0.27 g!t Au and 1.92 g!t Ag. Drill intercepts of the North Fork deposit also show significant gold values.Mineralization and hydrothermal alteration of these deposits are typical of porphyry deposits, although some differences can be noted. The Mount Tolman molybdenum deposit contains topaz alteration zones and is transitional between a plutonic type and a Climax-type molybdenum system. Other deposits, such as the Kelsey, Mazama, North Fork, and Margaret, are low-sulphide systems that contain significant amounts of magnetite."

Jan 1, 1995

By B. Misra, B. S: Sastry, Kollu S. Rao

"This paper reports the results of a finite element study of the geothermal heatflow into dry mine airways. For isotropic and unsteady state conditions the heatflow into mine airways is studied for a range of surface heat transfer coefficients between rock and air, and age of the airway. Dimensionless temperature gradient values are presented in tables for different values of Boit and Fourier numbers and the results are compared with Starfield tables and Gibson algorithm. It is found that Starfield tables have consistently over-predicted the G values with errors ranging from 2% to 10%. The differences between results obtained from the finite element study and the G values calculated from Gibson's approximation method are mapped. The small error values over a large range of Fourier and Biot numbers confirm the suitability of Gibson's algorithm to rapidly calculate G values for estimating the heat transfer from surrounding rock to mine air.IntroductionIn many underground mines heat is a major problem, and the provision of acceptable working conditions requires considerable expenditure on ventilation systems. The rational design and operation of these systems depend upon an understanding of the various sources of heat in the mine. The natural source, i.e. geothermal heat, contributes up to 80% of total heat added to mine air and it is difficult to analyze and predict the heat owing to a number of influencing variables. The problem of geothermal heat flow has been studied by many investigators (Goch, 1940; Starfield, 1966; Hemp, 1987; Amano et al., 1982; McPherson, 1986).The primary concern of this paper is to develop a better ready reference dimensionless transient temperature table for estimating heatflow at any stage of mine airway life."

Jan 1, 1994

Overview ?G-9 Discovery Hole 420 drilled May 2005 ?14.16% Zn, 1.76% Cu ?Greenfield discovery built into the G-9 Mine in under 4 years. ?Utilized a unique ?Parallel Track? approach to fast-track mine development. ?Raised over $200million in financing without a Feasibility Study. ?Mine built for $149.7 million, only 20% over PEA. ?Commercial Production declared April 1, 2009. ?G-9 Mine has now completed the first year of commercial production on April 1, 2010. ?Initial cash costs per pound of zinc US$0.39/lb -US$0.45/lb range. ?Mill operating at over1,900 tpd in March 2010, well above design capacity (1,500tpd) only one year after starting commercial production. ?Balance Sheet -$167 million assets, $24 million long-term debt, $22 million cash. ?Restarted Exploration ?excellent initial results. ?Strategically positioning Farallon to grow to a mid-tier mining company.

May 1, 2010