Search Documents

By Donald J. Barnes

Gold was found in samples collected from Pleistocene and Holocene stream and terrace deposits. Approximately 15,000 cu yd (11,400 cu m) of small and discontinuous terrace and stream gravel deposits in the study area are composed of material derived from sedimentary and granitic rocks. The detritus is subangular to subrounded, and poorly sorted, ranging from boulder to sand size. Gold values in samples collected averaged 8.2 cents per cu yd (gold value of $500 per oz). Pan concentrates and rock chip samples collected from reported mineralized zones showed an absence of economic minerals. Stream placer deposits are uneconomic. No potential was observed for metallic or nonmetallic minerals in the La Panza study area. No potential exists for gas, oil, or coal resources.

Jan 1, 1981

By George S. Rice

"""To prevent the propagation of mine explosions, the Bureau of Mines, Department of Commerce, recommends rock-dusting all coal mines, except anthracite mines, in every part, whether in damp or dry condition. It also recom¬mends that rock-dust barriers be used to sectionalize the mine as additional defense; but these should not be regarded as a substitute for generalized rock-dusting."" (Mine safety decision, No. 5, April 7, 1927.)The purposes of this circular are to present concisely the requirements for effective rock-dusting of coal mines in order to prevent propagation of mine explosions, and to point out the principal related facts on explosibility of coal dusts and mixed coal-mine dusts, as determined by extensive testing in the Experimental Mine of the Bureau of Mines. study of these principal facts on coal-dust explosibility in conjunction with the recommendations for rock-dusting, should help to make clear to mine operators and others concerned the necessity for systematic rock-dusting in all coal mines except anthracite mines, and the futility of inadequate or sporadic rock dusting.The descriptions of nearly 1000 explosion tests in the Experimental Mine are available in a forth-coming bulletin2 and in earlier publications.3For detailed specifications as to the kind of rock-dust, amount to use, where to be applied, and method of sampling and testing, the reader is referred to Bureau of Mines Serial 26064, and American Engineering Standard Committee ""Recommended American Practice for Rock-Dusting Coal Mines"" quoted in Bureau of Mines Information Circular No. 60305.Summary of Specifications for Rock-Dusting1. Mines to be rock-dustedAll coal mines, except anthracite mines, should be rock-dusted.2. Extent of rock-dustingAll open accessible parts of a coal mine should be rock-dusted, including slopes, entries, cross,-cuts, and rooms, headings and pillar workings to within at least 50 feet of the face.3 Amount of rock-dustingAfter cleaning up the coal dust as thoroughly as practicable, sufficient rock-dust should be used to have the mixture of remaining coal-dust plus the rock-dust in any zone contain 65 per cent or more of inert or noncombustible matter. First dusting may require 3 pounds to 5 pounds per linear foot of passageway.4. When to rock-dust In any zone or section (made by dividing the mine for rock-dusting purposes) when the incombustible content falls to 55 per cent, that section should be re-rock-dusted so as to bring the incombustible content well above 65 per cent."

Jun 1, 1927

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT's and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT's and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990

By D. K. Ingram, P. Jurovcik

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown that operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5 to 9 dB at the operator’s left ear and 2 to 5 dB at the operator’s right ear while hammer-drilling. This paper briefly discusses the preliminary design of a cab and the testing of materials for construction of the prototype. An explanation of the ideas behind the prototype design and fabrication are covered. Finally, the field test method and results are discussed in detail.1

By Doris M. Hyde

The Government of Belize maintained strict control over spending in 1982 as a means of protecting its import-dependent economy against the effects of a general worldwide recession. The modest economic performance was not expected to differ substantially from the $152 million2 gross national product (GNP) estimated for 1981. Exports and reexports were expected to decline in 1982, partly as a result of the Mexican peso devaluation. Imports were also expected to decline slightly in 1982, but the overall trade deficit was projected some-what higher than the $44 million experienced in 1981. On September 21, 1982, Belize became an independent state. As a result, the new Government became eligible for assistance from international organizations such as the International Monetary Fund, the International Bank for Reconstruction and Development (World Bank), and the United Nations Development Program (UNDP). Belize's independence from its former status as a colony of Great Britain was marred somewhat by the unsettled territorial dispute between Great Britain and Guatemala. Guatemala declared Belize was a part of Guatemala and. therefore. refused to recognize it as an independent state. Negotations between Great Britain and Guatemala continued without resolution.

Jan 1, 1984

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

As part of the Phase I study activity, a questionnaire was sent to a representative sampling of mining companies to obtain information on the uses, use conditions, personnel policies and other user concerns associated with front-end loaders. On-site visits to several of the mining companies were also parried out and the questionnaire was used during these visits as well. Five major areas were dealt with in the user questionnaire. These included: 1) Front-End Loader Critique - An open-ended form was employed to permit the mining companies to describe the particular things they liked and disliked about front-end loaders, in general, and/ or specific models in particular. 2) Usage - A form indicating the functions performed by front-end loaders and the numbers, makes and models of front-end loaders being used by mining companies. 3) Environment - A form where the user indicated the various types of conditions encountered in their use of front-end loaders. 4) Personnel - A form for describing factors pertaining to the qualifications of front-end loader operators. 5) Miscellaneous and Comments - A form permitting the user to comment on his feelings toward standardization of front-end loader operator stations.

Jan 1, 1973

By Cavallaro. J. A.

This report presents the results of a washability study of 455 raw coal channel samples with special emphasis on sulfur reduction. These raw coals contained on the average 14.0 percent ash, 1.91 percent pyritic sulfur, and 3.02 percent total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds. Finally a similar statistical evaluation is included showing composited data interpolated at Btu recovery levels of 50, 60, 70, 80, 90, and 100 percent. Graphical summations are presented for the various coal producing regions. Generally, significant sulfur reduction is achieved if the coals are crushed to a finer size and the higher specific gravity increments are removed. If a 50-percent Btu recovery was acceptable, then 32 percent of the samples tested could be upgraded to meet the current Environmental Protection Agency (EPA) standard of 1.2 pounds of S02 emission per million (MM) Btu when crushed to 14-mesh top size and separated gravimetrically.

Jan 1, 1976

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By H. Stuart Auvil

Twelve samples of run-of-oven coke were taken at coke plants in the United States and Canada. Sampling procedure was directed toward obtaining the highest possible degree of uniformity in the gross samples, so that variations in results caused by sampling variations were at a practical minimum. Under these conditions the standard deviation of the screen analysis test on 500-pound samples is found to range from 1.2 percent for the 1-inch screen to 4.5 percent for the 5-inch screen. At present, the A.S.T.H. standard method of test requires that results be reported to the nearest 0.1 percent. This implies a higher than actual degree of precision, and revision of the report required by the method is suggested. Much larger Samples than are generally tested are required to reduce normal testing errors to a point where they are not appreciable fractions of the total variations found in a smoothly operating plant. For example, it is deduced that over 100,000 pounds of coke must be screened to determine if ordinary day-to-day variations in screen analysis have appreciable effects on the performance of a blast furnace.

Jan 1, 1950

This report describes Phase I of the project --Development of a Mechanized Scaler --performed by Battelle, Pacific Northwest Laboratories for the U.S. Bureau of Mines. The objectives of Phase I were to 1) assess the needs of the industry as related to mechanized scaling; 2) conceive, evaluate and select mechanized scaler concepts; and 3) prepare preliminary designs of the selected machine concepts. To assess the scaling needs of the industry, we reviewed both U.S. and foreign literature, evaluated U.S. scaling accident statistics, reviewed existing mechanized scaling equipment, performed a series of mine visits and telephone interviews with mine operators, and assessed the applicability of a loose-rock detection system. The literature review identified over 25 scaler-related articles. However, little of the information could be used directly in the conceptualization and design portions of the project. Three articles did supply information on a number of machines used in Europe, along with statistics describing their effect on mine safety. For example, the French reported a 50% reduction in the total number of scaling-related accidents and a full 80% reduction in the number of lost-time injuries in the Lorraine mining district.

Jan 1, 1981

By Bertrand L. Johnson

Barite, the natural sulfate of barium (BaSO4), is the most important barium mineral. Normally it is white (opaque to translucent), but impurities sometimes render it yellow, gray, blue, brown, red, or black. Brown or red stains are commonly caused by iron oxide. Barite is unusually heavy (specific gravity, about 4.5); in fact, it is one of the heaviest of the nonmetallic minerals. It is brittle and fractures unevenly. The hardness of barite ranges from 2.5 to 3 but is usually about 3. It can be scratched by a copper coin. Pure barite contains 65.7 percent BaO and A.3 percent S03. Much of the crude barite ore mined, however, contains impurities; thus it has a lower content of barite and consequently less barium oxide. Commercial analyses show its total BaSO4 content. Barium also occurs in nature as the mineral witherite (BaCO3), which, however, is not common in the United States, and commercial deposits have been found only in California. Witherite is a yellowish-white, light-gray, or Kite mineral with a specific gravity of about 3, a hardness of 3 to 4, and an uneven to subconchoidal fracture.

Jan 1, 1941

By Floyd D. Everett

The Cougar Spar property is in southwestern Beaver County, Utah, approximately 35 miles by road northwest of Lund, a station on the mainline of the Union Pacific Railroad (fig. 1). Original fluorspar discoveries on the property were made a. short time before 1941. During 1941 lessees produced approximately 600 tons of ores averaging 40 percent CaF2. Bureau of Mines engineers examined the property in 1942 and recommended development. Work was begun in December 1942 and completed in October 1943. The area was mapped by members of the Federal Geological Survey during the project period. Development included surface trenching; drifting, and crosscutting, a short distance below the outcrop. The surface work comprised a total of 440 linear feet of bulldozer and hand trenches. A total of 550 feet of workings was driven on the 100-foot level. Samples were taken for assay from the trench exposures and from the underground workings as work progressed. Pocks in the area of the Cougar Spar property are igneous and consist mainly of fine-grained tuff and quartz monzonite porphyry. The fluorspar mineralization occurs in a northwest fault zone.

Jan 1, 1951

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By H. E. Powell, T. E. Hill, W. A. Calhoun

The object of this investigation was to determine the effectiveness of certain cationic flotation collectors , Ethomeens , in recovering fine particles of lead minerals from mill tailings at a grade equal , at least , to that of the mill feed ( 1.7 percent lead ) . The Ethomeens , derived from tertiary amines having one fatty alkyl group and two polyoxyethylene groups attached to the nitrogen , were evaluated by bench- scale flotation tests . The 14 Ethomeens tested consisted of four groups : Coco amine , soybean amine , tallow amine , and stearyl amine . The best results were obtained with coco amine C / 12 , soybean amine S/ 15 , tallow amine T / 12 , and stearyl amine 18/20 . From a feed containing 0.23 percent lead , rougher concentrate grades of 2.12 to 3.89 percent lead were obtained , with recoveries of 17.3 to 27.5 percent of the total lead . Some of the lead mineral particles recovered had diameters of less than 1 micron . In comparative tests , the Ethomeens , or polyethoxylated amine types of cationic surface active agents , were more selective than conventional xanthate collectors for flotation of slimed lead minerals .

Jan 1, 1964

By R. R. Sayers

The effect of comparatively low concentrations of carbon monoxide for short periods and under normal air conditions.of temperature and humidity , with the subject at rest , was studied by Dr. Yandell Henderson and his co -workers . In making recommendations to the New York and New Jersey tunnel commissions * he advised that , if the New York New Jersey vehicular tunnel be so ventilated that persons passing through the tunnel would be exposed to not more than 4 parts of carbon monoxide in 10,000 parts of air for not longer than 45 minutes , they would experience no ill effects . supplementary experiments , carried out by us in connection with our studies at the Bureau of Mines experiment station at Pittsburgh, substantiated this advice . ** In continuing our studies on low concentrations of carbon monoxide , we made a few experiments in a gas chamber where the conditions could be accurately controlled . The factors investigatel were : ( 1 ) The effect of long exposure in low concentrations of carbon monoxide ; ( 2 ) The effect of strenuous exercise ; ( 3 ) The effect of high temperature and humidity in low concentrations of ccarbon Lonoxide .

Mar 1, 1922