Search Documents

By D. P. Schlick

The German experience in dealing with the health hazard of respirable dust in underground mines is reported from first-hand observation in this Bureau of Mines paper. The report covers-- 1. The control of dust by water infusion, water spraying, and ventilation. 2. The sampling devices (tyndalloscope , konimeter , and BAT-I) and methods used to determine the dust concentrations in mines. 3. The systems of classifying hazardous and safe dust levels in mines. 4. The research facilities devoted to theoretical and applied work on mine dust and pneumoconiotic disease. Tile major research projects on dust and disease now underway in West Germany are outlined in an appendix.

Jan 1, 1970

By R. L. Montgomery

The heats of formation of lanthanum sulfate and the enneahydrate are -939.8 ± 3.1 and -1,587.1 ± 3.2 kcal. per mole, respectively. The heat of hydration is -32.5 ± 3.5 kca1. per mole. These values were obtained from heat-of-solution measurements of lanthanum oxide and salts. Low rates of solution precluded more accurate determinations of the thermal data. The heat of formation of the chloride was similarly observed to be -256.18 ± 0.28 kcal per mole. Heats of solution and combustion of lanthanum metal yield mutually concordant results, and earlier discrepancies reported in the literature may be ascribed to impurities.

Jan 1, 1959

By J. M. Singer

Flame propagation of lower limit hybrid coal dust-methane-air mixtures in vertical and horizontal flame ducts of 15.2 cm id and 1.8 m length has been investigated to provide information bearing on safety in mines. Fuel concentrations at lower limits of flame propagation and equivalences of coal dust and methane are much higher for continuing flame propagation than for short-span flame propagation in the vicinity of an "overdriving" ignition source. As the energy of the ignition source was increased, the flame speed and the distance of flame propagation from the ignition source increased, whereas the total fuel concentration at the lower limit decreased.

Jan 1, 1968

By M. M. Wong

Salt mixtures consisting of KC1, BaC12, and HfCl4 with RbCl or CsCl were investigated as electrolytes for refining hafnium. The presence of RbCI or CsCl in the electrolyte appeared to suppress the volatility of. Best electrorefining was obtained with an electrolyte containing 50.7 percent KCl, 27.l percent BaCl2, 15.7 percent CsCl, and 6.5 percent HfCl4. In this electrolyte, hafnium metal with an average oxygen content of 470 ppm was produced from an anode feed containing l,600 ppm oxygen. All metallic impurities were lowered, except titanium, manganese, and tin.

Jan 1, 1966

By Edwin B. Cook

This report presents the results of calculations of the equilibrium composition of the products of combustion with air of six different mixtures of octane CgH18, plus PbEt4 and halogen-bearing scavengers at three air-fuel ratios, at pressures of 5 and 30 atm., and at temperatures of 350°, 1,000°, 1,800°, and 2,000° K. The air-fuel weight ratio has the values 12, 15:12, and 18. The concentration of PbEt4, M, in milliliters per gallon of iso-octane, has the value 1 or 3. The word "case" is used to designate the halogen concentration. Three cases have been considered [ ]

Jan 1, 1953

1. Domestic Production and Use: In 1984, 12 companies operated 27 primary aluminum reduction plants, with 3 firms accounting for 57% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Missouri, and Tennessee 25%; Alabama, Arkansas, Texas, South Carolina, and North Carolina 20%; other States 20%. Based on published producer prices, output of primary metal in 1984 was valued at $7.2 billion. Aluminum consumption by 25,000 firms was centered in the east-central United States. Packaging accounted for an estimated 35% of domestic consumption in 1984, transportation, 20%; building, 18%; electrical, 9%; consumer durables, 8%; and other uses, 10%.

Jan 1, 1985

By David D. Walker

The purpose of the investigation was to describe and appraise tungsten deposits in Montana . The work supplements previous investigations made by Pattee ( 10 ) and Walker ( 17 ) in selected areas of the State . Scheelite deposits in tactite are the most numerous and most important economically , having accounted for nearly all of the State's tungsten production . Of the 64 deposits examined during the current study , 50 contained scheelite , 11 hubnerite , 2 wolframite , and 1 ferberite . The State's major tungsten production has been from scheelite deposits in Beaverhead County . The report lists , by counties , the type and grade of each deposit . The more important occurrences are accompanied by geological and assay maps .

Jan 1, 1963

By P. G. Pigott

This investigation by the Bureau of Mines demonstrated that building bricks can be produced by the steam-curing process from various types of industrial mineral wastes. Wastes, utilized to produce bricks, consisted of copper mill tailings, roofing granule fines, asbestos fines, and zinc mill tailings. Bonding of the wastes with either Ca(OH)2 or portland cement resulted in building bricks that met ASTM specification C73-67 for grade SW and MW bricks when evaluated in accordance with ASTM designation C67-66 on sampling and testing of brick. An economic evaluation of the process indicates the total operating cost per 1,000 bricks is about $36.

Jan 1, 1974

By J. B. Zadra, J. M. Gomes, Don H. Baker

Electrolytic deposition at 1,000 ° C in an electrolyte essentially consisting of 7 parts sodium pyrophosphate , 2 parts sodium chloride , and 1 part sodium tetraborate yielded tungsten of 99.9 percent purity . Scheelite concentrates containing 25 to 73 percent WO, and varying quantities of iron , lime , and silica were used as feed materials for the electrolysis . The metal contained less than 0.01 weight - percent each of iron , calcium , silicon , aluminum , carbon , and oxygen . Modification of the electrolyte permitted deposition of equal - quality metal from scheelite concentrates containing higher quantities of iron , calcium , and silica . The electrolytic separation of molybdenum and tungsten was accomplished by minor variations in the operating procedures .

Jan 1, 1964

By Donald R. Johnson

Apparatus developed by the Bureau of Mines for thermal analysis of oil shale was used to determine the thermal properties of shortite. Dissociation of shortite near 470° C occurs as an endothermic reaction that could consume significant quantities of heat in the oil-shale retorting process that produces shale oil. The shortite dissociation products undergo other thermal reactions that would not affect the retorting process. These reactions include crystal inversions near 365° C and 425° C and melting and decomposition endotherms above 500° C. Two separate reaction route for fusion and decomposition of the shortite decomposition products are dictated by the presence or absence of CO2 around the sample.

Jan 1, 1974

By D. J. Stoops, H. Kato, M. D. Carver

The effects of impurity elements silicon , aluminum, copper , nitrogen , and manganese , at 50 to 300 ppm, on properties of the zirconium alloy Zircaloy 2 were investigated . Variations in microstructure , mechanical properties , and corrosion behavior in some inorganic acid and salt solutions were observed with variations in level of impurity element . Corrodents were solutions of sulfuric acid , phosphoric acid , copper chloride , and iron chloride . Silicon was found to modify annealed microstructures by spheroidizing and dispersion of secondphase material throughout grains . Silicon or manganese improved ultimate and yield strength of the alloy without loss in ductility . All five elements affected corrosion rates of the alloy , the effect being generally different for each element .

Jan 1, 1964

By G. H. Hopkins

Like most industries, the refining industry has in recent years been confronted with the problem of a decreased martin of profit, due both to a general lowering of prices and to rising costs. This has resulted in accelerating a program of increased efficiency an evidenced by improved methods and the installation of equipment designed to affect a number of economies hitherto regarded as unimportant. Perhaps the most important of these has been that of fuel economy for, as is not often realized, a refinery consumes about one-tenth as much fuel as it produces. A recently completed canvas., made by the Bureau of Mines for the purpose of determining the trend of fuel consumption at refineries in the United States, showed the following outstanding points, (1) a decrease in the use of oil for fuel in 1926 of approximately 4,000,000 barrels as compared with 1925; (2) a small decrease in the use of coal; (3) a material increase in the use of gas, both natural gas and refinery gas; and (4) a considerable increase in the use of petroleum coke.

Jan 1, 1927

By Thomas P. Meloy

"The presence of respirable quartz-bearing mineral par-ticles has been well documented in many coal mines, and the Mine Safety and Health Administration regulations address the quartz content of mine dusts. Unfortunately, the correlation between the quantity of respirable quartz-bearing mineral particles and the pathogenicity of the dust is not strong. Work is currently underway by the National Institute for Occupational Safety and Health/U.S. Bureau of Mines and work is being included in the Respirable Dust Center Program by Dr. Seehra to determine the surface availability of quartz in mixed composition mine dusts. However, this paper propose a possible source of surface quartz or a spe¬cial region in the coal that may contribute to the pathogenicity of selected particles in the respirable dust.Assumed in this model is the hypothesis that either the cleat surface is coated with quartz or some cytotoxic sub-stance that in the body is capable of destroying macrophage and thus inducing a fibrotic response (1) that during the frag¬mentation a reasonable proportion of the respirable size coal particles contain some of the original cleat surface and that these particles have the same order of in vivo cytotoxicity as do the quartz particles. It may be that these cleat surfaced respirable size particles are only contributory to the overall pathogenicity of the coal dust, nevertheless, there are enough of these particles to to considered as a potential source of the cytotoxic dust particles.This paper demonstrates that if the cleat surfaces are mineralized with quartz or have a pathogenic coating, then in many mines there will be enough respirable coal dust particles containing some cleat surface to cause a fibrotic reaction. To understand why some of the dust particles contain as part of their surface some of the cleat surface, consider what happens when a beer bottle is broken. While there are a large number of beer bottle fragments, many of the fragments, particularly the larger fragment sizes, will have as a fraction of their surface part of the original beer bottle surface. The model and mathematics of this problem have been worked out by Meloy.(2-4)In the homogeneous IAC model, (2-5) a fragment or par-ticle resulting from comminution is equally likely to occur anywhere in the material being broken. Therefore the probability of a particle of size x having part of the cleat surface in it, p(x), is proportional to x. Thus:"

Mar 1, 1989

By Robert L. Chufo

The U.S. Department of Energy Pittsburgh Research Center,1 has developed and field tested a spatial, spectral sensor for measuring the thickness of mineral deposits. Knowledge of the dielectric constant of the material is not necessary because the electrical properties of the media are determined automatically along with the thickness or distance measurement. The technology was developed to measure the thickness of coal remaining in the roof and floor of a mine or the thickness of a coal pillar remaining between two mining entries for the purpose of guiding a mining machine. However, field tests have shown the new technique is equally valuable for measuring the thickness of each layer in a multilayer manmade structure such as highway paving or building foundations and the thickness of geological deposits other than coal, such as, salt, granite and sandstone. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple dipole sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data and enables frequency domain signal processing to solve the problem of media, target and antenna dispersion. The technique overcomes the problem of multipath reflections from nearby metal structures and avoids the use of radio frequency absorbing material. In its present form the system measures material thickness of zero to over 3 m to within ±2.5 cm accuracy. The system parameters are variable to suit the application but for most applications default values of 40 cm antenna motion with measurements made at 401 frequencies from 0.6 to 1.4 GHz at each of 32 antenna positions with a power level of 0 dBm or less are more than adequate to provide a satisfactory signal-to noise ratio. In the range of 0 to 10 m the system operates in the continuous wave mode and by simply turning off the transmitter for ranges beyond 10 m the problems of time domain processing are entirely avoided. The technique can be implemented with a vector network analyzer, a servo controlled L-band antenna positioner, an IEEE488 bus controller and a process computer. An electronics package designed and constructed to operate in the harsh mining environment and providing 1, 2 or 3 dimensional image presentation is being evaluated as a replacement for the network analyzer. Key words: Ground penetration radar, Spatial, Spectral

By H. Kenworthy

A zinc-pyrite ore from the Gray deposit in Jo Daviess County, Ill., was successfully concentrated on a laboratory scale. Initially, drill cuttings were submitted for separation of zinc and iron concentrates. Subsequent to mine development, a large sample of coarse ore was submitted to ascertain its amenability to sink-float treatment to produce a low-grade zinc-iron concentrate and discard a clean tailing. The samples of ore were submitted to the Rolla Metallurgical Branch by the Mining Division of the Federal-Bureau-of Mines. They were obtained during the recent war as a part of the extensive government program to increase metal production through exploration for new mineral deposits and investigation of old mineralized areas. The first sample consisted of about 3,000 pounds of drill cuttings collected, during the Bureau?s churn and diamond- drilling program. The second sample was taken at a later date, after Tri-State Zinc, Inc., had opened the deposit and commenced milling the ore. This sample consisted of a ?ton-of mill feed crushed through 2 inches and collected over a period of 3 days.

Jan 1, 1949

By R. M. Santmyers

Umber and sienna, like ocher, are naturally occurring mineral pig- ments composed largely of clay permeated with hydrated iron (ferric oxide), but they differ from ocher in that they also contain hydrated manganese oxide. The presence of manganese accounts for their browner color. In addition to silica and alumina (clay) and the coloring oxides of iron and manganese, these pigments often contain lime, barium, and other metallic salts as impurities. Sienna most nearly approaches ocher in chemical composition, and the chief distinction is its physical character. It grades into ocher with de- creasing iron content and into umber with increasing manganese content. Sienna is translucent rather than opaque and is more of a stain than a pigment; as the iron oxide content is rather high (often 60 to 80 per cent), the color is strong and rich and varies from pure brown to reddish brown. This pigment raw sienna, terra di Siena, and Italian earth. is known under several names: Burnt sienna is a pigment of an orange-brown tint made by cautionsly calcining raw sienna. It is divided into two grades; American, and Italian burnt sienna. American burnt sienna is a reddish-brown pigment containing from 25 to 60 per cent iron oxide (Fe2O3). One grade, found in Pennsylvania, analyses as high as 80 per cent and is mown as double strength sienna. Italian burnt sienna is a pigment generally containing more iron than the American product, averaging 60 to 75 per cent iron oxide.3 American pig- ments of the same iron content differ materially in shade, having a Havana- brown color, whereas the Italian is more of a maroon. Italian siennas when tinted with 20 per cent of white, show a bluish tint, whereas American siennas yield a brownish or yellowish hue. Raw umber, also known as Turkey umber, Levant umber, and terra ombra, is a greenish to yellowish brown siliceous and ferruginous earth, containing a considerable proportion of one or other of the higher oxides of manganese, Mng04 and MnO2." It is similar in many respects to raw sienna except that it is much coarser and contains more manganese oxide. All umbers contain over 5 per cent of manganese dioxide. Like sienna, umber is a permanent pigment, not being injured by light or by impure atmospheres. Burnt umber (velvet brown, chestnut brown, etc.), results from the calcination of raw umber. The color is much richer and warmer than that of the raw umber. The colors are equally permanent and can be used in conjunc- tion with all other durable pigments.

Sep 1, 1931

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

By E. Chin

The only economically significant mineral exploited in Banglades - during 1981 was natural gas. Nitrogenous fertilizer production was important to the agricultural sector and was totally dependent on the natural gas for fuel and raw material. Domestic cement plants were also fu pled by natural gas. The flat river-delta terrain for most of Bangladesh makes the potential for discovering major mineral deposits poor. No large deposits of metal ores have been found and only in the small hilly southeastern section of the country is there even much chance of finding any. Heavy mineral sand deposits may eventually be exploited along the Chittagong coastline. There is a good potential for crude oil discoveries. The Bangladesh economy has been heavi¬ly subsidized by billions of dollars of foreign aid since the country's inception. A World Bank report recommended total aid needs of over $2.6 billion in fiscal year (FY) 1980-81. It received commitments for barely over one-half that amount.

Jan 1, 1983

By Edwin M. Thomasson

HELIUM SHIPMENTS in 1964 exceeded the volume shipped during the previous year for the 15th successive time. Shipments from Bureau of Mines helium plants were 667.4 million cubic feet,2 about 6 percent more than in 1963. Production at Bureau of Mines plants totaled 784.5 million cubic feet. An additional 3,193.1 million cubic feet, which was produced by private companies participating in the helium conservation program, was purchased by the Bureau and stored underground for future use. The Bureau of Mines continued to sell helium at $35 a thousand cubic feet, the price established in 1961. Substantial railway freight rate reductions for tank car shipments of helium went into effect during the year, resulting in a lower delivered price for helium. As the Nation moved ahead in the space age, it became increasingly apparent that helium would continue to play an essential role in research, in technology, in defense, and in industry.

Jan 1, 1965

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962