Search Documents

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

By James W. Bass

Introduction Atmospheric fluidized bed combustion (AFBC) is an improvement over coal-fired boiler design. It offers several advantages over conventional boilers. AFBC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling that can in turn increase a boiler's fuel flexibility. AFBC process The fluidized bed boiler that operates at atmospheric pressure on the fire side (AFBC) is relatively simple and no different in purpose from those pulverized coal boilers used by utilities today. Fluidized bed boilers can generate steam at the pressure and temperature needed by modern steam turbines. Only the firing system is different. In fluidized bed combustion, the fuel can be almost any coal or waste fuel. It is burned in the presence of a bubbling bed of limestone. Air is forced through the bed at a velocity sufficient to support the weight of the bed particles. When the bed is fully fluidized, it bubbles like a boiling liquid. Although the burning coal makes up less than 1% of the fluidized bed, all the bed particles are heated quickly by the turbulence. The calcium in limestone reacts with sulfur dioxide produced in coal combustion to form calcium sulfate in a dry solid state. In this way, sulfur emissions regulations can be met without installing flue gas desulfurization equipment. Boiler tubes submerged in the bed absorb heat directly from the turbulent solids. The heat converts water in the tubes to steam or superheats the steam. Because of the intimate contact of the boiler tubes with the fluidized bed, heat transfer is highly efficient. Consequently, less boiler tubing surface is needed to generate the same amount of steam as in a comparable pulverized coal boiler. The optimum temperature for sulfur capture is relatively low, about 815°C (1500°F) as opposed to 1370°C (2500°F) for pulverized coal boilers. This results in the formation of lower levels of NON. Because operating temperatures are below those that fuse coal ash, a single design can burn a variety of coals without slagging or fouling problems. TVA's AFBC development program Tennessee Valley Authority's (TVA) involvement in AFBC development began in 1974 and has addressed the technical uncertainties through a comprehensive program of design, experimental, and analytical studies. In 1979, TVA and the Electric Power Research Institute (EPRI) developed plans for a 20-MW AFBC pilot plant, a 10-fold scale-up over the next largest test facility. Pilot plant design features TVA constructed the pilot plant at the Shawnee Steam Plant near

Jan 4, 1986

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By A. v. E. Conradie, I. Nieuwoudt

Comminution and flotation circuits are frequently perturbed by disturbances, such as feed particle size variations, ore hardness and varying mineral liberation, which can have a significant impact on the recoveries and grades. Although advanced control strategies can neutralize many of these disturbances, few such systems have been implemented at present. One reason is that it is only recently that the requisite sensor systems have been developed and used to control froth flotation systems. Another is owed to the complexity of these non-linear interactive systems. In this paper, a plant-wide control strategy is considered, wherein both unit operations have a single overall control objective. The automated design of the controller is based on an advanced evolutionary algorithm viz., Symbiotic, Memetic Neuro-Evolution (SMNE), for developing neural network controllers in a reinforcement learning framework. A rigorous phenomenological comminution and flotation model was used to develop suitable neurocontrollers, which used all possible sensor inputs and available manipulated variables. The neurocontroller managed to identify optimal or near-optimal operating conditions consistently and showed robust performance in the presence of significant disturbances. The results suggest that evolutionary reinforcement learning offers a very competitive approach towards the development of integrated non-linear controllers for mineral processing plants. Keywords: neural networks, control, flotation, comminution, evolutionary reinforcement learning

Jan 1, 2003

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010

By Douglas C. Brunot

Mabey Inc. is providing for the shoring design for the Naples bay Center project, located in Naples, FL. The excavation is approximately 374' long by 164' wide and is 27'-8" deep at the shoring line with a groundwater level six feet below present grade. The project Excavation is for a multi-use facility for residential and retail with underground parking. The shoring design will be incorporated into the foundation walls for the building. Mabey is using its pre-engineered Super Powerbrace Plus (SPP) wales and Mega Struts to support the excavation in two phases. The system design and the design of all the pre-engineered components are by Mabey. The foundation is supported on drilled shafts arranged with the building column grid. The excavation will be completed in two phases to allow for equipment mobilization and operation on a site with limited access. The construction sequence will begin with placement of the drilled shafts. The drilled shafts will also serve as the building columns. After the drilled shafts have cured, 630 AZ24-700 x 45 ft. long sheet piles will be installed. The sheets will be arranged in two phases, divided by a center row of piles. Since de-watering in south Florida is very expensive and often downright impossible prior to placing the seal slab, all the initial foundation and excavation bracing work will be completed with groundwater in situ. The entire excavation will be excavated to 5 ft. below ground surface to allow for the installation of the wale support brackets at 12 ft. on center, welded to the sheet piles. After the support brackets are installed, the SPP hydraulic wales and the Mega Strut hydraulic braces may be installed for both phases. Once the frames and struts are in place, Phase 1 excavation is completed, followed by Phase 2 excavation. The 4-ft. thick seal slab is then placed and cured in the wet. De-watering is now possible with the seal slab in place. Once the excavation is de-watered the leveling slab is placed and cured. The center row of sheet piles is then cut off at the top of leveling slab. With the leveling slab cured, the sheet piles have enough strength to support the excavation without the frames and struts near the ground surface. The permanent sheet piles are then seal welded for water proofing and the foundation walls are cast with the sheet piles. The design is modelled in 3D using REVIT to ensure accuracy of the design. The earth pressures are developed using Coulomb theory as there is a top frame and the frame and sheet pile are flexible and move to develop an active pressure wedge. Earth pressure uniform loads and loads from predicted surcharge are modeled in STAAD to determine load effects on the SPP frames and Mega Struts. Coulomb theory and Mabey’s structural model will be tested through monitoring with Mabey’s LIVEPin system. LIVEPin will be placed in struts for each phase of construction. The LIVEPin results will be calibrated with the structural model to determine actual frames forces and will also determine the actual earth pressures applied to the system from surrounding soil. Mabey has used the LIVEPin system in similar applications and this has helped us determine modelling accuracy.

Jan 1, 2018

It is shown that factors associated with conditions whIch are thermodynamically favourable for the formation of CuS04 in roasting lead to high copper recoveries on leaching. One of these factors is the ratio of the air to solids used for roasting. This can be varied widely without loss of temperature control in the sulphating roasting of many Australian copper concentrates.Thus, the prediction of the air to solids ratio corresponding to a maximum p(SO3) value, for a given concentrate and temperature, is of importance in fluidized bed roasting, since this could be associated with the formation of a maximum quantity of CuS04. Calculations are presented which predict this air to solids ratio, not only for a given concentrate composition, temperature, and pressure, but also for air which is enriched with sulphur dioxide or oxygen.

Jan 1, 1968

Based on X-ray phase analysis and exploratory experiments, a new technology was developed to recycle multiple valuable elements in spent Al2O3-based catalyst. The experimental results showed that after roasting at 750°C for 30 minutes at an Na2O:Al2O3 mol ratio of 1.2, the leaching recoveries of alumina, vanadium and molybdenum from the spent catalyst were 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by barium hydroxide and barium aluminate. The precipitation recovery of vanadium and molybdenum was 94.8% and 92.6%, respectively. Al(OH)3 is prepared from sodium aluminate solution using the carbonation decomposition process. The purity of Al2O3 is 99.9% after calcinations, and the recovery of alumina can reach 90.6% in the whole process. The Ni-Co concentrate was leached with sulfuric acid, and a nickel recovery of 98.2% and a cobalt recovery of more than 98.5% were obtained under the experimental condition of 30% (w/w) H2SO4, 80°C, a liquid: solid ratio of 8:1 (by weight), a reaction time of 4 hours and a stirring rate of 800 rpm.

Jan 1, 2007

By A. J. Kraemer, H. M. Thorne

The following account of oil-shale operations in Australia is based upon infor- mation obtained by the authors while visiting Australia from September 15 to October 7, 1947, supplemented by published data, and augmented by analyses of samples of oil shale and its products at the Oil-shale Research and Development Laboratories of the Bureau of Mines at Laramie, Wyo. The primary objective of the authors' trip to Australia was to obtain, first hand, information regarding the equipment and methods used by National Oil Proprie- tary, Ltd., at Glen Davis, New South Wales, in mining oil shale, extracting oil from it, and refining the shale oil. This company was operating the only oil-shale plant that had been active in Australia since 1945. The plant comprised an oil-shale mine, 104 modified Pumpherston (Fell) retorts in 2 batteries, a hele refinery, and a 3-inch gusoline pipeline to the railroad loniing terminal t Sun Junction, 30 miles away. There were, also, the usual and necessary any uralities, such as a power house, mechanical shops, offices, and laboratories One Information regarding the company's operations was wance because of its bear- Ing upon the synthetic liquid fuels program of the Bureau of Mines, pursuant to the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C., 321-325, as amended). objective of the Bureau's program. In accordance with the maniate of the Act, is to furnish American industry cost and engineering data necessary for the development of synthetic-liquid fuel industry, and an obvious means of obtaining some of these data is to learn how oil shale is being mined and retorted and how shale oil is re- rined in countries where these operations have been conducted on a plant scale for many years. The authors spent 2 weeks at the plant of National Oil Proprietary, Lt., at Glen Davis, and were afforded every opportunity to obtain letailed and specific information regarding all aspects of the company'a operations.

Jul 1, 1951

Jan 1, 1989

Dynamics of Three Phase Contact Line Motion in Liquid-Liquid-Solid Systems - Impact of Surface Roughness

Sep 13, 2010

By M D. Hannington

On the southern flank ofLihir Island, a group of three volcanic cones were discovered at water depths from 1000 - 1500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts, and porphyritic phlogopite basalts. One of the volcanoes has a recently erupted ejecta blanket (recovery of warm ash!), containing a suite of abundant mafic to ultramafic xenoliths. These xenoliths appear to represent a unique cross-section of subduction-modified mantle material sampled by volatile-rich primary fore-arc magma during its ascent to the seafloor. The most spectacular finding was the discovery of an active hydrothermal system with associated vent fauna and mineralization at Edison Seamount, and the recovery of unusually gold-rich (up to 43 ppm Au) hydrothermal precipitates in 1050 m water depth at the top of Conical Seamount, only 25 km south of the world-class epithermal Ladolam gold deposit on Lihir. The discovery of submarine hydrothermal vents associated with highly alkaline, quartz-undersaturated fore-arc volcanics represents a significant departure from similar hydrothermal systems on the mid-ocean ridges and in back-arc basins. The high gold grades in hydrothermal precipitates at Conical Seamount may indicate the first documented example of a shallow-marine epithermal system analogous to those known on land, and has important implications' for the gold potential of submarine arc environments.

Jan 1, 1995

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997

By R. G. Burn

"A brief outline will be given of the concept of risk and its implications with regard to investment in exploration. The relationship between risk and decisions under uncertainty will be examined as a prelude to identifying those factors which contribute to exploration risks:consideration of the effects of corporate objectives (e.g. survival, expansion, diversification) on exploration strategy and ultimately on success or failure, exploration and mining as an investment (the relationship between risk and reward) and the desired return on investment; exploration odds, funding levels, staying power, financial exposure and the concept of gambler's ruin;origins of uncertainty in exploration decision-making-man-made risks and natural hazards; the nature of introduced constraints at each exploration decision stage and their effect on the rate of success;improving the chances of success and the invest reduction of risk through sound exploration strategy, effective project generation and efficient target detection capabilities."

Jan 1, 1984

Geological maps, data, and prospectivity analysis relevant to mineral exploration in New Zealand have recently been released. Regional-scale geological mapping is increasingly available for the country through the QMAP 1:250 000 Geological Map of New Zealand programme. Published QMAP sheets Greymouth, Wakatipu, Waitaki and Dunedin cover large areas of interest for mineral exploration companies. The QMAP geological data are also available in digital form for use with other digital datasets using GIS software. Crown Minerals, in cooperation with GNS, have completed two gold prospectivity studies; the first covering mesothermal gold in the South Island, and the second encompassing epithermal gold in northern New Zealand. These studies have defined areas of interest for these two mineralisation types and assembled geological, mineral occurrence and production, geochemical, geophysical, topographic and cultural data into projects for use with GIS software. Included are the results of prospectivity modeling for gold using these data and specific mineralisation models. The prospectivity studies and relevant data are freely available on CD through Crown Minerals and are intended to encourage mineral exploration in New Zealand.

Jan 1, 2003

By Xiaodong Wang

A liquid metal flow generated by a magnetic field whose traveling direction is periodically reversed, the Reversed Traveling Magnetic Field (R-TMF) is studied. The modulation frequency ranges from 0 to 6 Hz. Ultrasonic Doppler velocimetry probes the generated fluid flow. Depending on the modulation frequency, a number of characteristic flow features are exhibited. A transition frequency (approximately 4 Hz) exists, above which the flow is no longer sensitive to the force modulation. Below this transition point, the amplitude of the velocity oscillation increases, and then below fm = 0.05 Hz, it saturates around a value close to that observed without any modulation. A theoretical model to obtain an analytical solution of electromagnetic force and to predict flow motion is developed, which is fairly in agreement with the experiments.

Jan 1, 2009

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006

THE Broken Hill mining field, approximately 31 miles in length, is at present being exploited by seven companies, viz. : North Broken Hill Limited, Junction North Broken Hill No Liability, Broken Hill Proprietary Block 14 Company, Broken Hill ProprietaryCompany Limited, Sulphide Corporation Limited, Broken Hill South Limited, and Zinc Corporation Limited.The variation in size and shape of the ore-bodies in the mines of these companies, together with the many alterations in pitch and dip, necessitates differences in methods of mining, each company working out its problem in its own particular way.In the matter of chute construction for the handling of the ore broken in the stopes, each mine belonging to the above companies has adopted a style particularly its own, though it may be said that one or two of the types approximate very closely to each other, slight minor differences only being noticed in the design. It is the purpose of this paper to give a brief description of the principal types of chutes now in use in th,e various mines on the field, and in doing so they may roughly be classified into three groups, viz:1. Bulk Chutes, 2. Circular Chutes, 3. Square-set Chutes.The Bulk type of chute is used in the North and British mines of the North Broken Hill Limited, the Central and Junction mines of the Sulphide Corporation, the South Blocks mine of the Zinc Corporation, and the Block 14 mine.The Circular type of chute is used by the Broken Hill South mine and the South Blocks mine.The Square-set chute is used in the Proprietary mine, the Junction North mine, and occasionally in other mines where the square set method of mining is a necessity, and more particularly as mullock passes.

Jan 1, 1925

By L Hussey, H Thanasekaran, J Kohmuench

Conventional flotation technology has historically failed to achieve high recoveries when treating <15 µm particles (Lynch et al, 1981). The new StackCell™ flotation technology was developed to specifically target this particle size range, and was tested at pilot plant scale at Mt Keith Nickel Concentrator. The streams tested, Slimes Rougher Tailings and Fines/Slimes Cleaner Tailings, represent 21% and 11% of the total nickel lost to tailings in the plant. Laboratory scale test work indicated that an economically significant fraction of these losses was consistently available to be recovered by additional flotation. The pilot plant experimental scope included over 50 tests. A grade recovery curve for each stream was developed, as well as information on the effect of ore type, feed rate, wash water, air flow, collector and frother on the performance of the cell. The single StackCell was able to achieve nickel recoveries of 16.8% and 16.5% on the Rougher Tailings and Cleaner Tailings, respectively, at grades consistent with these blocks. Additional test work of the StackCell in a cleaner scalper duty yielded final quality concentrate with a maximum nickel recovery of 59.5% for the single stage StackCell. Laboratory scale simulation of the downstream impacts of the StackCell operating as a cleaner scalper indicated a net recovery benefit of up to 2.0% for this cleaner block.Tests were completed to compare residence time requirements of the StackCell, as compared to conventional flotation. In 55 seconds, the pilot plant StackCell achieved 50% of the recovery of a 960 second laboratory scale conventional flotation on the same feed material. The apparent improvement in flotation kinetics is attributed to the novel high intensity aeration system, which provides efficient bubble-particle contact thereby shortening the residence time required to achieve high recoveries. The smaller footprint and lower energy costs of such a cell are also benefits of this technology, which is being considered for industrial scale installation as a result of this test work. Given the industry’s historical poor performance treating slimes with conventional flotation, it is clearly best practice to challenge the status quo through innovative new technology, such as the StackCell.CITATION:Hussey, L, Thanasekaran, H and Kohmuench, J, 2017. The application of high intensity flotation technology at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 259–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017