Search Documents

By Emerson de Andrade Monteiro

As ligas de titânio ao Nióbio apresentam grande potencial de desenvolvimento graças a excelentes combinações de propriedades. O tratamento termomecânico a elas conferido é importante para atingir as propriedades desejadas. O presente estudo tem como objetivo avaliar o efeito da conformação mecânica nas propriedades da liga Ti42Nb forjada a frio com 80% de encruamento e seguido de envelhecimento. Foram realizados ensaios de tração, medidas de dureza, metalografia e microscopia das superfícies de fratura. Foi possível observar que a liga Ti42Nb apresentou maior dureza e consequentemente maior resistência após o envelhecimento.

Aug 16, 2017

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

? Develop a six year capital budget for future emission controls at Western Springfield Power Plant that would provide long-term operating certainty

Jan 1, 2005

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

The Mount Angelo prospect outcrops as two copper rich gossans, the larger of which is 250 ft long and 70 ftwide. The mineralization is epigenetic and replaces part of a brecciated and disturbed lime tone and calcareou sediment sequence.Magnetic and self potential survey indicated a substantial body of sulphide mineralization, the top of which was approximately 100 ft below the surface.Diamond drilling confirmed this and established the presence of a mineral body of at least 500,000 tons, extending to a depth of 300 ft. Of the 500,000 tons, 200,000 ton are primary copper ore which a ays 2 per cent copper.This mineral body is not economic at present, but could become economic if copper mining is established elsewhere in the district...

Jan 1, 1966

The Manto Verde mine is found in the coastal ranges of the Atacama desert, 1000 km north of Santiago, Chile . The deposit is a fault-breccia specularite-oxide copper mineralisation hosted by the Jurassic andesites of La Negra Formation. It is located in a tensional fault that joins twoparallel arms of the Atacama Fault. The mine is in feasibility study: reserves are of the order of 60 Mt at 0.9 wt per cent soluble copper; mining will be undertaken at a rate of 11 000 tpd utilising an open pit and the ore will be heap-leached with acidified sea water, with copper recovery and by SX/EW.

Jan 1, 1992

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By R. J. Traube

The purpose of the Inherently Safe Mining System (ISMS) project is to develop continuous and conventional coal mining equipment and systems which will reduce the incidence of fatal and nonfatal accidents in the working sections of underground bituminous coal mines by application of existing technology. This 3-year program, initiated on 18 June 1971, is being conducted in three phases: ? PHASE I (8 months) Systems Analysis Concept Design Planning ? PHASE 11 (16 months) Design Procurement Manufacture Preliminary Testing ? PHASE III (12 months) Underground Coal Production Demonstration.

Jan 1, 1972

There is a significant amount of historical mining and exploration information available. This information is often distributed throughout a number of reports or plans, available from a variety of sources, and in many differing formats. The ability to capture paper-based historical information in a modem digital format provides mining and exploration companies with valuable information that can be used in a number of ways; for example, reassessments of exploration or mining work previously undertaken, or used in conjunction with current exploration information.   The purpose of this paper is threefold. Firstly, to present the paper-based historical information; highlighting some of the problems encountered, solutions to those problems, and any assumptions used. Secondly, to present the historical data in digital format, and demonstrate the tools available to analyse geological and associated information, and finally, to illustrate some of the potential future applications of the information, including mining optimisation, mine design and scheduling.   The Glenorchy scheelite/gold prospect has been used as an example. Within the overall prospect two smaller areas were selected. The Mount McIntosh and surrounding areas, focuses on exploration and surface excavation information. The Mount Judah area (State and Kelly-Taylor workings) focuses on underground mining and exploration information.  

Jan 1, 2001

By John L. Thames

The benefits of water harvesting as an alternative to conventional reclamation were demonstrated on the Peabody Coal mines in Northeast Arizona. The project produced food crops for four years, and demonstrated that a catchment/crop area ratio of about 2.5:1 was sufficient to obtain sufficient water from the 11 inch annual precipitation to produce garden and fruit varieties in quantities equal to or exceeding national production averages. The economic returns exceeded those of the conventional practice of returning the mine area to rangeland by at least ten fold. Subsidence of the regraded spoil was the only major problem in maintaining the system. Although, water harvesting systems have the potential of providing high economic returns and greater social benefits, as demonstrated by this project they are presently at variance with the strip mining regulation.

Jan 1, 1984

By S. Sinha, S. Ganguly

"In an opencast mine explosives are used for fragmentation of rock. Inefficient use of explosive energy in an opencast operation produces excessive ground vibration, which is measured by peak particle velocity (PPV). To mitigate ground vibration, it is essential to develop a model to predict PPV. At present empirical models are used. These models are based on only a few input variables, hence they fail to take into account the effects of the myriad factors that cause ground vibration. Due to lack of explicit knowledge about the complex mine blasting system the scope of application of mathematical and statistical modeling techniques is limited. The artificial neural network (ANN) technique is a learning algorithm that can remove some of these limitations and can be applied to predict PPV. In this paper an ANN model is developed for prediction of blast vibration using 248 data records collected from three coal mines with diverse geomining conditions. The correlation coefficient between measured PPV and model output was found to be 0.96 and the average error percentage 11.85. The ANN model output was compared with the output of three empirical models that are widely used for prediction of PPV. The correlation coefficient between the PPV predicted by an empirical model and measured PPV data was 0.63 and the relative error percentage 38.47. This result demonstrates the superiority of the ANN model compared to empirical blast models. By using site-specific structural discontinuities as input the model performance can be further improved. Sensitivity analysis and 3D plotting were used to gain further knowledge about blast-induced ground vibration. IntroductionIn an opencast coal mine explosives are used for fragmentation of coal and overburden. If the explosive energy is not fully utilized it causes blast-induced ground vibration, which may damage nearby structures. Ground vibration is expressed as peak particle velocity (PPV). During different stages of mine planning and operation, it is necessary to use a ground vibration prediction model for blasthole design. Selection of the modelling technique is crucial. Mathematical and statistical modelling techniques have limited application because of the lack of explicit knowledge about the complex mine blasting system. Vogiatzi (2002) highlighted the problem of multicollinearity in case of statistical modeling techniques. Mutalib et al. (2013) stated that mathematical models are unable to capture the nonlinear relationship between several blasting-related parameters due to the complexity of the model input data. However, the difficulty involved in modelling complex blast vibration problems can be removed by adopting an alternative soft computing modelling approach. One of the soft computing techniques is the artificial neural network (ANN). Ragam and Nimaje (2018) developed an ANN model for predicting PPV using six input variables. Kosti et al. (2013) stated that the conventional predictors fail to provide acceptable prediction accuracy. They showed that a neural network model with four mine blast parameters as input could make significantly more accurate on-site predictions. Sayadi et al., (2013), using a database from Teheran Cement Company limestone mines, found that a neural network resulted in maximum accuracy and minimum error. Khandelwal and Singh (2009) developed an ANN model using 150 data records from an Indian coal mine with site-specific rock characteristics and geomining setting. Khandewal and Singh (2007) built a ground vibration prediction model for a magnesite mine using four prediction variables with 20 data records. Kamali and Ataei (2010) predicted PPV in the structure of the Karoun III power plant and dam using an ANN. El Hafiz et al. (2010) evaluated ground vibration predictors using data from a single-station seismograph at a limestone quarry in Egypt."

Feb 1, 2019

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By James Scott

Outline Deposit Overview and Brief History ?Geologic Setting ?Local Geology ?Petrography ?Geochemistry ?Mineralization ?Geochronology ?Conclusions Deposit Overview ?Porphyry Cu-Mo-Au ?Discovered 1957 (BIK Syndicate) ?Various programs, most significant: ?Hecla(1970s) ?Teck(Late 1970s Early 1980s) ?Copper Fox Metals (2005 -Ongoing ?optioned from TeckComincoin 2002) ?Measured and Indicated Resources: ?847Mt grading: ?0.292% Cu ?0.019% Mo ?0.202g/t Au ?1.796g/t Ag ?Total ~ 0.485 % Cu Eq.

May 1, 2006

By E. A. Lowe, J. W. Smith, C. W. Overton

"The operations of Bethlehem Copper are situated in the south-central interior of British Columbia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Columbia.The minerals are chiefly chalcopytite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies some pyrite is present. Average grade of mill feed is 0.55% copper.History of Milling Operations Production commenced in December 1962 at a rate of 3,000 tpd in a plant that comprised two-stage crushing followed by rod and ball milling. Production ratings were increased to 6,000, 10,000 and 12,000 tpd by the addition of a further stage of crushing and more rod and ball mills. When the last expansion was completed tonnage throughput exceeded the 12,000 ton designed rate and was stabilized at 15,500 tpd.However, recovery did not meet expectations at the expanded rate because of coarse flotation feed. Capacity in the rod mill circuits exceeded the subsequent fine grinding capacity, resulting in poor liberation. Studies were initiated to improve recovery without decreasing throughput.Description of Operation Prior to Pebble Milling Crushing with primary, secondary and a closed tertiary stage proceeds at a scheduled 20.5 shifts per week. Fine ore screened on 1/2"" x 4"" apertures is stored in a 30,000-ton bin ahead of two 12.5' x 15' rod mills. Rod mill discharge joins secondary ball mill (one 10.5' x 14' and one 11' x 14') discharge for classification in a single 50"" cyclone which closes the secondary mills. Overflow from this cyclone is split between three third-stage ball mill-pump-cyclone circuits (two 11' x 14' and one 12.5' x 15'). Prior to addition of the two pebble mills the flotation feed was produced by this three-stage grinding system. Grinding criteria are shown in Table I."

Jan 1, 1975

By Gregory J. Canivan

Three test pile programs were conducted in Charleston, South Carolina to evaluate differences in bearing resistance due to installation methods. The tested piles were installed with impact hammers and vibratory drivers through soft clays and/or loose sands into the Cooper Marl, a stiff calcareous marine clay or silt. Piles driven into the Cooper Marl experience significant capacity gain with time following initial installation due largely to pore pressure dissipation. Pile size and pile type were both known to affect pore pressure generation during installation and subsequently the capacity gain with time. The test programs were primarily conducted to optimize pile design values and construction methods with regard to trestle construction but the results also contribute to the understanding of driven pile behavior. High strain dynamic testing was performed on several open-end pipe and H-piles. The measured difference in long-term bearing capacity of the H-piles as a result of the two installation methods was negligible, while the short-term bearing capacity of the pipe pile was larger when the piles were installed using impact hammers. The lower short-term resistance in the vibratory driven piles is attributed to larger excess pore pressures generated during installation compared to those generated during impact driving.

Jan 1, 2002

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

By O. C. Blade

Total sales of diesel fuel in the United States continue to Increase. This growth is due primarily to two causes: More conversion to diesel units by the rail-roads In recent years, and the greater use of diesel engines in trucks, busses, and tractors. Following are some figures on the distribution of the fuel computed from data issued by the Bureau of Mines.2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,522,000 barrels during the first six months of 1955,3/ corresponding figure for 1954 was 91,170,000 barrels. Information on the properties of this engine fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1955

By Edgar Carlos García Flores

El presente texto señala al Perú como modelo de sistemas de explotación minera para Bolivia -en tanto desarrolle, prepare y explote las minas con calidad y así incrementar la producción de sus operaciones mineras. Asimismo, describe los procedimientos idóneos para seleccionar las tablas geomecánicas, la ingeniería de explosivos, equipos de acarreo y los elementos de sostenimiento adecuados para las excavaciones subterráneas con el objetivo de tener operaciones de calidad, seguras y óptimas.

Feb 1, 2015