Search Documents

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003

By W. J. Grose

The Embankment Place office development over the platforms of Charing Cross Railway Station in London has presented many interesting and unusual problems to the engineers involved with the project. The main structure is supported on widely-spaced columns which penetrate the station platforms and underlying vaults, calling for high capacity foundations built in severely restricted spaces. Hand-dug underreamed piles were chosen. Whilst a conventional design approach was taken to size the piles, a detailed appraisal of ground movements was made to explore the effects of the new building loads on the existing foundations, not only beyond the site perimeter but also those amongst the new foundations. Before construction of the pile proper could take place, it was necessary to sink a caisson through the upper unstable and water-bearing soils. This being identified as a high-risk item, a full-scale trial was carried out prior to embarking on the main works. The twenty-one hand-dug piles were 2.5m diameter, over 30m deep and belled out to between 4.5m and 6.6m.

Jan 1, 1989

By R. L. Virta

Six companies mined fire clay in Missouri and Ohio during 2004. Production, based on a preliminary survey of the fire clay industry, was estimated to be 398 kt(438,700 st), valued at $9.81 million. This was slightly less than the production and value figures from 2003. Missouri was the leading producer state. It accounted for more than 70 percent of the U.S. production. Consumption Domestic producers sold or used fire clay primarily for refractory applications. This application accounted for 79 percent of the market. Refractory products made using fire clay include firebrick and block, grogs, high-alumina brick and specialties, refractory mortars and mixes, and saggers.

Jan 1, 2005

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8'-3" wide by 9'-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By A Golsby

Although much talked about, social licence to operate (SLTO) is a relatively new concept that has been deemed as one of the four biggest business risks to a mining project over the life-of-mine. There is no accepted single definition of SLTO and this author understands SLTO to be stakeholder perception of the legitimacy of a project, a company or an industry. At a specific site, and across different sites within the same organisation, SLTO ranges through different levels according to stakeholders’ degrees of acceptance in time and space. Management of SLTO is vital for the mining sector but is difficult as it is informal and intangible. Although there are no key performance indicators, there are certain indicators that enable relative measurement of the ‘level’ of the SLTO. Because of the importance of the SLTO, information management during the entire life-of-mine, from exploration to rehabilitation, becomes crucial for the continued operation of a project. This paper identifies ten basic principles for the management of information to support the SLTO.CITATION:Golsby, A, 2014. Managing information to support a social licence to operate, in Proceedings Life-of-Mine 2014 , pp 389–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Laurence G. Britton

Accurate flammability and ignitability data for chemicals form the cornerstone of procedures used to assess the hazards associated with commercial chemical production and use. Since 1967 the ASTM E27 Committee on the Hazard Potential of Chemicals has issued numerous, widely used consensus standards dealing with diverse testing and predictive procedures used to obtain relevant chemical hazard properties. The decision to issue a standard rests solely with the membership, which consists of representatives from industry, testing laboratories, consulting firms, government, academia, and instrument suppliers. Consequently, the procedures are automatically relevant, timely, and widely applicable. The purpose of this paper is to highlight some of the widely used standards, complemented with hypothetical but relevant examples describing the testing strategy, interpretation, and application of the results. A further goal of this paper is to encourage participation in the consensus standards development process. The paper is published in two parts. The first part (in the preceding issue of Process Safety Progress) dealt with the E27 standards pertaining to thermodynamics, thermal stability, and chemical compatibility. The second part, published here, focuses on the flammability, ignitability, and explosibility of fuel and air mixtures. © 2005 American Institute of Chemical Engineers Process Saf Prog 24: 12?28, 2005

Jan 1, 2005

By Yaw Boadi, Andrew McCallum, Sandy Gray, Yavuz Atasoy, Peter Wemyss

"Various full-scale test programs and installations of the InLine Pressure Jig (IPJ) have provided evidence that pre-concentration of the difficult to leach sulphide mineral through gravity can provide significant increases in economic recoveries. The continuous gravity concentrates are intensively treated either by re-grinding or Intensive Cyanidation. Data from various mine sites worldwide is presented. Treatment of complex ore bodies with this low cost methodology may render previously uneconomic ore bodies financially viable and assist in the recovery profile of transitional ore.INTRODUCTIONThe use of gravity is made extremely attractive in complex ore situations due to the low cost of operation, typically a few cents per ton operating cost and lack of chemicals.Gold mines which suffer from poor recovery due to complex mineralogy such as Stibnite, Arsenic, Carbon, Telluride, Silver and other pacifying agents such as Iron, which can form coatings, can all benefit from the process proposed in this paper. The key issue is not overall recovery as much as one of economic recovery. The key to this is maximised recovery at the lowest possible capital and operating cost. Other options such as flotation are reviewed but are not seen in many instances to be the panacea due to issues discussed in the paper. The use of the InLine Pressure Jig in the re-circulating load of the milling circuit is a cost effective means of recovering a sulphide/gold concentrate containing the complex mineral assemblages which require re-grinding and intensive leaching for optimised gold recovery.The benefits of Jig Assisted Grinding (JAG) are many and the challenge over the past years has been developing, understanding, implementing and evaluating the benefits of various flowsheet models. This has involved the reconciliation of results in plant scale trials back to the original laboratory test program. The following paper outlines the insights gained in this area through extensive work carried out by many people across both laboratories and plant sites in Australia and overseas. The examples in this paper are some of the work carried out on a few selected sites but similar work has been carried out on other sites such as Penjom, Granny Smith and Agnew. This work has eventuated in several installations which we believe have great importance in the future of the gold processing industry. They will lead the way forward to the modern all-gravity plants of the future.Compared to flotation, for the recovery of sulphides, gravity is a simple option. The simplicity generally translates to low capital and operating cost."

Jan 1, 2004

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By M. Hitch, M. B. Lytle

Resource development conflicts arise largely due to differences in worldview between those who support and those who oppose development. This paper illustrates how societies and civilizations with different worldviews produce different levels of creative and economic energy. A questionnaire was created to build a database of responses to test whether worldview and resource development are correlated. Factor and multivariate regression analysis determined correlations for respondent groupings. Results showed a positive correlation between the respondents\u2019 worldviews and their attitudes toward resource development. Correlations became stronger as the homogeneity of the sample subgroups increased.

Jan 1, 2017

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

Techniques have been developed for the dissolution of a wide range of rocks and minerals by a sodium peroxide sinter process. A olarge number of elements are determined by atomic absorption spectroscopy, and other elements such as arsenic and sulphur are determined by chemical analytical methods. The methods adopted to overcome inter-element and ionization effects on the atomic absorption results are discussed.

Jan 1, 1974

By Donald P. Tuchman, Justin R. Patts, Emanuele G. Cauda, Andrew B. Cecala, Elaine N. Rubinstein

Video techniques for monitoring exposure, such as NIOSH’s “Helmet-CAM,” employ both real-time dust monitors and mobile video cameras to assess workers’ respirable dust exposures. Many real-time personally worn dust monitors utilize light scattering sensing elements, which are subject to measurement biases as a function of dust type (size, composition, shape factor) and environmental conditions such as relative humidity. These biased and inaccurate dust measurements impair the monitor’s ability to properly represent actual respirable dust concentrations. In the testing described, instrument mass concentration data was collected using three different types of commonly used commercial off-the-shelf personal dust monitors and compared to a reference standard. This testing was performed in a calm air (Marple) dust chamber in which three units of each make and model (for a total of nine monitors) were used for each test. Equivalency factors (EF, a multiplier to match the Thermo TEOM 1400a reference instrument) ranged between 0.746 and 1.879 across all dusts and environmental conditions tested, and between 0.821 and 1.519 on the ISO test dust.

By Donald P. Tuchman, Justin R. Patts, Emanuele G. Cauda, Andrew B. Cecala, Elaine N. Rubinstein

Video techniques for monitoring exposure, such as NIOSH’s “Helmet-CAM,” employ both real-time dust monitors and mobile video cameras to assess workers’ respirable dust exposures. Many real-time personally worn dust monitors utilize light scattering sensing elements, which are subject to measurement biases as a function of dust type (size, composition, shape factor) and environmental conditions such as relative humidity. These biased and inaccurate dust measurements impair the monitor’s ability to properly represent actual respirable dust concentrations. In the testing described, instrument mass concentration data was collected using three different types of commonly used commercial off-the-shelf personal dust monitors and compared to a reference standard. This testing was performed in a calm air (Marple) dust chamber in which three units of each make and model (for a total of nine monitors) were used for each test. Equivalency factors (EF, a multiplier to match the Thermo TEOM 1400a reference instrument) ranged between 0.746 and 1.879 across all dusts and environmental conditions tested, and between 0.821 and 1.519 on the ISO test dust.

For the first time in its history, the George A. Fox Conference let its focus venture away from the friendly confines of the East Coast of the United States to spend part of the one-day conference looking at projects from around the globe. With a record-setting attendance of 377 people, the conference, titled ?Tunneling: An international perspective,? opened with a keynote speech from special guest In-Mo Lee, professor, Korea University in Seoul, South Korea. He is also the president of the ITA-AITES. In a sweeping presentation, Lee walked the packed audience through some of the most fascinating and challenging projects in his home country. Among the projects he spoke about were Korea?s longest railway tunnel, the Solahn Tunnel and the Inje Tunnel, a freeway tunnel that is 11.94 km (7.4 miles) long.

Jan 1, 2012

By Zhao-shu Sun, Mao-lin Li, Rui Cui

"Fankou Mine produced pyrite concentrate (PC) from the tailings by rougher and scavenger flotation before 2010, with the averaged S grade of 40.54% at recovery of 79.34%. The economic value of PC increases with its purity. When the S grade of PC feed to sulfuric acid plant is over 47%, the pyrite cinder can reach a high Fe grade of 62% which can be directly sold as iron concentrate. On this background, engineers in Fankou Mine set the PC with S grade of 47% as target.The direct way to reach that goal was to clean the rough PC Lots of cleaner flotation tests were conducted and the balanced strategy was to produce two ranks PC with the S grade of 47% and 38% at the recovery of 44.20% and 36.17%, respectively. The dual-product flowsheet was successfully industrialized in 2010. In order to further improve the quality of PC, gravity separation was introduced into the flowsheet. The numerical simulation and tests were performed to evaluate the beneficiation and classification performance of hydrocyclone as it treated the rough PC. It was shown that the underflow of hydrocyclone could addressed the S grade of 47%, and the finer size overflow could also be enriched to PC with S grade of 47% by flotation, due to the contained pyrite with well liberation. That is to say, with the ingenious addition of hydrocyclone to treat the rough PC, single PC with S grade of 47% could be achieved. The new flotation-gravity separation flowsheet was commissioned to produce the high quality PC at the end of 2013. The averaged S grade is 47.20% at recovery of 82.26% in 2014. The two steps flowsheet improvement maximizes the enterprise benefits and leads to simple utilization of Fe in pyrite in downstream industry."

Jan 1, 2016

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

By V. J. Parks, Leonard Obert, A. J. Durelli

The state of stress in the region where core discing initiates has been investigated through the use of three-dimensional photoelastic models and the results of this study have been compared with those of a previous investigation of rock models. This comparison showed that discing initiates at a point of maximum shear stress, but that the magnitude of the shear stress, as determined photoelastically, is much larger than the shear strength of the rock as deter-mined from conventional triaxial testing. Moreover the shear stress required to produce discing is not constant, but depends on the applied stress field. Possible explanations for these effects are included in this article. In both exploration core drilling and overcore drilling to determine the stress in rock, occasional sections of the core obtained are broken into a series of discs.I* This discing phenomenon has been investigated in the laboratory to ascertain the state of stress required to produce it. The objective of the study was to obtain information that would make it possible to approximate the state of stress in subsurface rock from which disced cores are obtained. Referred to as the discing test, this laboratory study was conducted to determine the applied axial and radial loads required to produce discing in cylinders of rock from several sources. The dimensions of these cylinders are given in Fig. 1. Discing was produced by first applying an axial load to the cylinder and then diamond drilling the core along its axis. The radial load was then incrementally increased until discing initiated. The discs fractured or ruptured* on surfaces approximately normal to the axis of the core (planes A, B, C, D, E, Fig. 2). In many instances, the bottommost disc fractured before the drill had advanced past the points F and F', cre- ating a mush room-shaped fracture surface FEF'. Alternatively, it was also found that the same shaped fracture surface could be created by first drilling in an unloaded core to some point, say F and F', and then triaxially loading the core until fracture occurred on the plane FEF'. Jaeger and cook4 produced similar fracture surfaces in specimens subjected only to a radial biaxial load. From these laboratory studies and observations made in the field, it can be inferred that fracture or rupture initiates in the proximity of the lowest point in the kerf area, (at F and F', Fig. 2) and that the fracture or rupture surface progresses inward from this point. The experiments described above, however, do not provide any information as to the state of stress at the point at which fracture or rupture initiates. In the investigation discussed in the following sections, a three-dimensional photoelastic analysis was conducted to determine the stress distribution in the proximity of the kerf area of a triaxially loaded plastic (epoxy) cylinder containing a short section of core.

Jan 1, 1969

By Charles L. Kusik

A study was conducted for the Bureau of Mines, U.S. Department of the Interior, to provide information which will lead to an increase in the recycling of mineral materials, in order to help conserve the Nation's mineral resources. Data were collected on energy requirements to recycle prompt industrial and obsolete scrap for nine metal commodities: Iron and steel, aluminum, copper, zinc, lead, stainless steel, titanium, tin, and nickel and nickel alloys. Major process routes for recycling were considered, starting from the first collection point through scrap preparation, transportation, smelting and/or refining to the molten metal, ingot, or other semi- finished form approximately equivalent to a primary metal of a similar composition. Available data for 1976 were collected on the amounts of each metal commodity recycled by major scrap categories. In addition, energy requirements were estimated for separating municipal solid wastes into four major categories: Refuse-derived fuel, and magnetic, aluminum, and glass cullet fractions. Finally, areas of research were identified to enhance recycling and/or increase the efficiency of energy use.

Jan 1, 1978