Search Documents

Fine Coal Evaluation by Gravity Methods

Sep 13, 2010

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

By E. T. Turkdogan

Jan 1, 1962

By K. Leutwyler

The key to realistic casing stress analysis in thermal recovery installations is accurate knowledge of the temperatures involved. Much information leading to prediction of heat losses from tubing string to wellbore has been published. This .same information permits calculation of casing temperature under certain conditions. This paper reviews the basis for most of the published work, the line source solution to the diflusivity equation and examines some of its application criteria in the light of unsteady-state conditions. An alternate finite differences method is presented for correlation, and experimental data pertaining to the heat transfer mechanism in the annulus is reported. In the light of the information presented in the paper, it appears that the assumption of a line source for the tubing-wellbore system is valid even for reasonably short periods of heat flow, .such as "steam soak" operations. The empirically modified equation presented earlier matches computer derived results of the finite differences approach lor periods as short as 50 hours. Previously predicted cas ing temperatures and the associated stress levels are thus verified based on these correlative computations and the reported experimental information. Fall out from the computer output resulting in some studies of the influence of insulating cement properties on casing temperature, and experimentally studied effects of nitrogen placed in the annulus at various pressures., are described. INTRODUCTION Generally speaking, predictions of average casing temperatures have been based on an idealized model involving a centralized tubing string at uniform constant temperature radiating energy towards the casing under steady-state conditions.'. ' Heat is transferred away from the casing to the formation by unsteady-state conduction across thermal barriers consisting of cement and the mud sheath. Heat balances written on the casing permit prediction of instantaneous casing temperatures. During early periods of injection, casing temperature varies appreciably as a function of time; however, for long injection times this variation decays as heat flow from the wellbore to the formation stabilizes, and it becomes virtually negligible as conditions surrounding the wellbore become quasi-steady-state (Fig. 1). Carslaw and Jaeger -escribe a solution to the diffusivity equation for a line source (Fig. 2). A constant supply of heat is introduced into the medium from the line placed into the origin of the x-y coordinate system and parallel to the z-axis. Heat spreads outward in the infinite cylindrical solid and the temperature increase on a line going through point (x, y) parallel to the z-axis at a distance r can be predicted by: The following criterion must be considered: the Carslaw and Jaeger equation is obtained on the basis of a large

Jan 1, 1967

By R. Webber, D. Averill, L. Whittle, D. Moffeti, G. Kassakhian

"This paper describes the recent pilot-plant work carried out on two alternative processes capable of producing an effluent containing less than 10 pCi/L total radium-226 activity and very close to 3 pCi/L dissolved radium-226. The processes incorporate coprecipitation of radium with barium sulphate by the addition of barium chloride in continuously stirred tank reactors followed by either chemical coagulation with ferric chloride, flocculation and clarification, or polymer-aided dual-media filtration. IntroductionUranium mines in Canada have practiced radium removal from tailings basin effluents since 1965. Treatment consists of addition of barium chloride to precipitate radium as barium- radium sulphate and provision of natural or constructed settling ponds for sedimentation. This process, however, has been identified as being deficient in that it allows particulate or suspended radium-226 releases which are higher than the regulated dissolved values». Also, the large size of some of the settling ponds is believed to represent a real limitation of the present technology because of inferred difficulty in recovery of barium-radium sulphate precipitates.The Federal Government Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical/chemical treatment systems as an alternative to settling ponds. In response to the SubGroup recommendations, a bench-scale study began in March 1976at the Wastewater Technology Centre (WTC) of Environment Canada . The results of this study indicated that coagulation and flocculation of the precipitate from barium chloride addition is a viable alternative to sedimentation in settling ponds(3). The bench work was expanded and accelerated in 1977, with financial assistance provided by the Atomic Energy Control Board. Subsequently, a research program with a larger scope was developed; this program is jointly managed and funded by government and industry, as shown in Table I.One of the goals of the joint program is to develop, at pilot scale, a physicalI chemical process to reduce the radium-226 content of uranium mining and milling effluents. Target radium-226 activities for treated tailings basin effluents were set: namely, 10 pCil L total and 3 pCil L dissolved radium 226. Extensive bench-scale and pilot-scale work was conducted through 1978 and 1979 and has culminated in the development of two physical/chemical processes. This paper describes work carried out at a pilot plant which led to the selection of the two physical I chemical processes for demonstration. In short-term tests, the processes produced effluents meeting the radium-226 target activities."

Jan 1, 1980

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

By Lees M. G, Vitnell B. W

The post-war need to increase coal production promoted an intensive drilling campaign. Ineffectiveness in core recovery inclined the coal industry towards percussion drilling rather than diamond drilling. The Joint Coal Board, recognising the greater potential of core drilling, has actively encouraged improvement in techniques and equipment. One outstanding need was a barrel which, over and above other improvements being achieved, would permit recovered core to be examined before it had been subjected to the increased fragmentation and displacement which to date has been inevitable except in core which has been drilled in solid sticks û as New South Wales coal rarely can be drilled. In conjunction with Triefus Pty Ltd a barrel with a split inner tube has now been evolved, as a result of which, core can be more accurately logged, division in to lengths for analysis more aptly made, any core loss more reasonably allocated to appropriate plies, and a greater percentage of core recovered û of the order 95 per cent and more. The one half of the split inner tube is lifted from the other and the logging completed before the core is disturbed.

Jan 1, 1957

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

By William R. Barton

Sampling to determine development potential of beryllium deposits was conducted at 31 New England localities. A total of 54 additional areas where the geochemical environment appeared favorable were sampled to determine if economically interesting percentages of beryllia (BeO) might occur. Newry Hill-Plumbago Mountain, Maine, Iron Mountain, N.H., and Long Island, Maine, were investigated in some detail to determine the size and grade of deposits. The mineralized pegmatites at Newry Hill-Phunbago Mountain are extensive but very low grade; at Iron Mountain the ore bodies are very rich but of small volume; at Long Island beryl occurs with molybdenite, wolframite, and scheelite, but the tonnage of ore was not determined.

Jan 1, 1968

By Chikaosa Tanimoto

INTRODUCTION Bratislava is located at the intersection of important traffic routes, including motor-ways, roads, railways, air traffic, trading, and inland waterway with an important harbour. The construction of the D2 Motorway Bratislava, Lamacska cesta Stare grunty was the last missing section of D2 Motorway and its completion linked the Czech Republic through Bratislava to the Hungarian Republic. Traffic was obliged until its completion to use the Lamacska Road and Mlynska Dolina, which were the most heavily trafficked roads in the city. The section of D2 Motorway to be completed in 2006 was 3,300m in length, of which the SITINA Tunnel was approximately half the length. After putting into operation the transit traffic(motorway) and urban traffic was separated. Transit traffic by passing the town was eased. The junctions D2 with Lamacska Road (Harmincova) and Mlynska Dolina also allowed better use of the motorway for the urban traffic The tunnel construction was specified by the features with the highly weathered and thermally altered granitic rock formation with the overburden of Quaternary sediment of 2?4 m thick, very thin overburden, severely controlled deformation limit and environmental protection. The tunnel had to be excavated beneath and nearby the academic complex area and the zoo, where sensitive facilities exist and animals live in. The tunnel consisted of two tunnels (Tunnel A and B) with the length of 1,415 and 1,440 m, respectively. The overburden thickness was in the range from 10?30 m. The standard cross-section and the one with invert arch were 79.5?81.5 m2 and 92.1?93.3 m2. The excavation took 21 months from September 2003 to May 2005. The construction was based on the concept of NATM. The SITINA Tunnel was the third application of NATM in Slovakia, following the BRANKISKO Tunnel (commenced in July 2003) as the first and the HORELICA Tunnel (in October 2004) as the second NATM practice. To protect the surrounding structures and citizens from tunneling operations, seismic monitoring was performed in association with blasting. The allowable limit of blasting vibration was fixed to be under the particle velocity of 15 mm/sec. The tunnel excavation cleared this limit as expected before construction. In driving through the difficult geological situation the excavation work hit 49 faults, and some of them occasionally caused serious face instability. In principle, the rock formation has been affected by the high hydrothermal effect and the resultant clay filing along faults and joints. The auxiliary reinforcement with the 4?8 m long pipe roofing was needed to protect the vicinity of mining face area. This operation extraordinarily required additional works and time which had not been expected before construction.

By Joseph A. Conway

This paper is one of a series dealing with the mining and crushing methods and costs of the nonmetallic industries, prepared under the sponsorship of and in cooperation with the U. S. Bureau of Mines,. The quarrying methods described in this paper are those used at the Monocacy trap rock quarry which annually produces from 450,000 to 500,000 tons of crushed stone. This property is located 3 miles east of Birdsboro at Monacacy, Pa., and is one of the three quarries operated by the John T. Dyer Quarry Co. Throughout the paper an effort is made to explain the various methods used and the cost of operation.

Jan 1, 1931

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

By Gregory M. Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

By D. P. Nicholson

The current phase of office development at Canary Wharf in the London Docklands includes twelve multi-storey buildings varying from eighteen to forty stories in height. The area of Canary Wharf South comprises five multi-storey buildings with low level in fill podium and garden areas. Three of these multi-storey buildings have "pile-cap" designs where the entire building load is applied to the piles. The remaining two buildings have "piled-raft" designs where allowance is made in the design for part of the building load to be transferred to the raft formation. Using a piled-raft design approach has enabled savings to be made on the number of piles used below the raft. This paper describes the calibration analysis undertaken to validate the design method. The ground conditions at the Canary Wharf site are typically fill and recent gravel deposits over the overconsolidated clay and sand of the Lambeth Group. Below these strata is the Thanet Sand. The Lambeth Group provided the founding layer for the raft and contributed to the pile shaft resistance. The Thanet Sand stratum provided the bearing layer for the 1.5m diameter base grouted bored piles. The piled-raft design required an assessment of the building load transfer through the raft to the formation layer. This load transfer led to significant increases in effective stress in the soil below the raft and thence a corresponding increased the capacity of the piles. This interaction of the raft with the prepared formation contributed to between 27% and 45% increase in total vertical load carrying capacity of the piled-raft substructure compared with the pile-cap design method. The development of the piled-raft design was carried out in three main phases: ? Development of the approach and validation analyses. ? Design work on various schemes resulting in detailed design packages. ? Validation analyses using full 3D finite element analysis (presented herein). The validation of the piled-raft design approach was initially carried out against published case histories for piled-raft interaction. To improve on the validation work a full 3D finite element analysis of a simplified pile raft and superstructure (which contributes stiffness to the raft) was undertaken; the analysis included only a quarter of the structure due to assumed symmetry of the structure and vertical loading. This 3D validation analysis is presented herein. The analysis was carried out using the Oasys LS-DYNA finite element program. Prior to carrying out the analysis of the piled-raft an initial finite element analysis was carried out to back analyse a fully instrumented field pile test providing accurate modelling of a single pile performance. This back analysis allowed confidence in the soil parameters used in the 3D model; comparisons of shaft and base resistances between the pile test and the FE model calculations for the single pile are presented. The parameters provided in this work were then carried into the full 3D model of the piled-raft. The 3D model of the piled-raft structure included 18 piles (12 full piles and 6 half piles on an axis of symmetry of the model).

Jan 1, 2002

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

Thermodynamics of Non-Cyanide Gold Solvents The present status of the raw material base in the gold industry requires specific ways to recover gold and silver from ores. Most gold is closely associated with sulfides which require flotation followed by pressure or bacterial oxidation. The next stages of processing usually require using expensive operations for the preparation of leaching. A lot of researchers want to find a new alternative solvent for the extraction of precious metals from these products. According to the authors, one of the best ways is to use sulfur-based solvents (thiosulfate, sulfite, and their various mixtures). Thermodynamics of gold and silver thiosulfate dilution are calculated for conditions: the concentration of Au - 200 mg/L, oxygen - 3.2 mg/L, thiosulfate - 79 mg/L, OH- - 170 mg/L. the general result is the possibility of process remains under standard conditions. (erAu = = 0.035 V, ?G298 = - 29.18 kJ/g-atom ??). Silver with thiosulfate forms two strong complexes: [AgS203]- and [Ag(S203)2]3-. ?G0 = -1027 kJ/mol. The complex [AgS203]- is less stable: ?G0 = 486 kJ/mol. It should be noted that despite the high stability of gold complexes, the sodium thiosulfate may decompose to sulfite and elemental sulfur during the process, especially when heating. Gold is slightly soluble in the sodium sulfite solution, however it forms the strong complex [Au(SO3)2]3-. Depending on the concentration of free S2O32-ions, silver with sodium sulfite forms three complexes: [AgSO3]-, [Ag(SO3)2]3- and [Ag(SO3)3]5-. The dissolution speed of gold in sodium sulfite solution may be in the same range as it is during cyanidation. In this case, a practical application of sulfite process can be also used, especially for the products containing free elemental sulfur. In conclusion, sulfite-thiosulfate gold lixiviants can be used for concentrates after pressure oxidation of the cakes.

Sep 13, 2010

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d'une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

The whole of the iron ore required by the Broken Hill Proprietary Company Limited at the Newcastle Steel Works, and Australian Iron and Steel Limited, at Hoskins' Kembla Works, is drawn from the Iron Knob, Iron Monarch, Iron Prince and Iron Baron deposits situated in the northern part of Eyre's Peninsula, South Australia.The Iron Knob and Iron Monarch deposits are near the township of Iron Knob, approximately 42 miles W.S.W. of Port Augusta, whilst the Iron Prince and Iron Baron deposits are some 18 miles due south from Iron Knob, in another group of leases, the adjacent township being known as Iron Baron.The ore mined at Iron Knob, Iron Monarch, Iron Prince and Iron Baron is conveyed on the Company's 3ft. 6-in. gauge tramway to Whyalla, on the western side of Spencer's Gulf, approximately 45 miles south by west of Port Augusta whence it is shipped to Newcastle and Port Kembla.SHORT HISTORY.The establishment in South Australia of the lead smelting industry at Port Pirie, Dry Creek and Port Adelaide in the...

Jan 1, 1937