Search Documents

By B. Moore, Y. J. Zhang

In today’s competitive dimensional stone business environment, use of available technology is critical to achieve and maintain a competitive advantage. Awareness of improvements in diamond cutting technology, operation planning/scheduling, and geotechnical data manipulation/implementation are the keys to success. This paper presents the modern techniques of limestone sawing and quarrying developed and adopted by Indiana Limestone Company, Inc.(ILCI).To fulfill the growing market demands, ILCI’s quarries are committed to deliver planned quantities of all type of stone blocks in a variety of different colors, sizes, and textures. This involves scheduling which quarry ledges should be mined and when in order to minimize unnecessary inventory buildup. Challenges associated with ILCI’s operation are discussed and summarized in the closing of this paper.

Jan 1, 2004

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By D. J. Burdon, Anthony Caplan

"(1) The radiological appearances of pneumokoniosis on the Kolar Gold Field is described in detail. The characteristic abnormality is the. presence of a diffuse, fine annular and punctate mottling. (2) The frequency of symptoms could not be determined with any degree of accuracy, but it is believed that symptoms are absent and there is no incapacity until profuse radiological mottling is present, i.e., after long exposure to dust. (3) There is an increased predisposition to tuberculosis, which, if it occurs, affects the prognosismost unfavourably.(4) Pathological examination shows that the radiological mottling is due to the presence inthe lung of numerous small dust-cdll aggregates (up to T5 mm. in dia.) deposited around the smaller bronchioles and blood-vessels.(5) The dust-cell aggregates are relatively acellular but when tuberculosis is superadded thereis an excessive cellular and fibrotic reaction.(6) The difficulties of defining the radiological and pathological appearances of early pneumokoniosisare discussed.(7) The incidence of pneumokoniosis in 7,653 workmen with 5 or more years’ undergroundservice was 43-75%, but it is suggested that in future the incidence will be appreciably lower.(8) The methods of- dust production and the chemistry of mine dust are described. It isshown that the free silica-content of air-borne mine -dust is relatively low.(9) The aetiology'of the pneumokoniotic lesion is discussed."

Jan 1, 1947

Organization Place Date 1917 American Electrochemical Society Pittsburgh, Pa. Oct. 3-6 American Institute of Mining Engineers St. Louis, MO. Oct. 8-13 American Gas Institute : Washington, D. C. Oct. 16-19 American Institute of Architects Philadelphia, Pa. _ Dec.. 26-29 American Society of Mechanical Engineers New York City. Dec. 26-29 American Mining. Congress State Chapter Phoenix, Ariz. Dec. 26-29

Jan 10, 1917

By James H. McCutchan

The small and remote mine operators must comply with the Federal Mine Safety and Health Administration regulation requiring them to train and maintain mine rescue teams. The alternative is for the operators to contract with established teams within two hours travel time of their mine. Many of these remote operations are too far away from established teams and have too few employees to make up the necessary teams. Many cannot comply with the regulation either from a manpower or economic standpoint. The Office of Arizona State Mine Inspector, under the direction of the Honorable James H. McCutchan, State Mine Inspector, entered into a contract with the Bureau of Mines to develop the concept of a volunteer mine rescue program. This program with the assistance of the mining industry and volunteer rescue organizations, has planned and instituted a statewide volunteer mine rescue organization. The trained and equipped volunteers are stationed throughout the state and can respond to a mine emergency within the time constraints.

Jan 1, 1984

By Stephen Hodgson, Ken Brouwer

September 2005, Northern Dynasty Mines announced the discovery of a new, high-grade deposit at its Pebble project in southwest Alaska. The product of insightful geological investigation, Pebble East, as it is now known, is quickly growing into one of the most significant copper deposits in the world. Preliminary analysis shows it could reduce the U.S. copper supply deficit by a third. The new deposit has also altered Northern Dynasty’s view of how Pebble should be developed. This article describes the Pebble project as it is currently understood and outlines the work planned for the next several years.

Jan 1, 2007

By B Brown, P J. Hommert, B J. Thorne

"Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. A"" improved damage model based on microcrack growth in tension allows finite elementcalculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model."

Jan 1, 1990

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

Elongates are commonly used as stope support in South African gold and platinum mines. To evaluate the effect of the inherent strength, stiffness and yield variability associated with elongates, a statistical method is presented which addresses and quantifies the support performance at various levels of certainty. The analysis, which is based on a normal distribution, makes use of force-deformation curves determined from multiple laboratory compression tests on the same support type. The applicability of the method is illustrated making use of actual performance capabilities of various types of elongates. In order to ensure a high probability that support units installed underground exceed the standard support performance curve established by means of laboratory tests, the statistical mean of a suite of tests based on the same support type is downgraded. The ?correction factor? is a function of the mean and standard deviation of the test data, as well as the sample size of units deemed to control the local rock mass stability. It is shown that downgraded performance curves based on a high probability (90 to 95percent) of support units exceeding this performance level are suitable to ensure that the design of support systems will in variably meet the design criteria. In the highly discontinuous hangingwall rock mass typically associated with intermediate- and deep-level mining operations, the interaction between adjacent support units is comparatively limited (at the support spacings commonly used). Therefore, the appropriate sample size (n) of the support units controlling the local rock mass stability should be n= 1. In shallow mining conditions, sample sizes of up to n=5 may be warranted, depending on the spacing of joints and other discontinuities in the hangingwall.

Jan 1, 2001

By Fahimeh Dehghani, Louis Ackah, Tathagata Ghosh, Justin Godbold, Jia Liu, Meisam Peiravi, Manoj Mohanty, Azam Baharlouei

Primary economical deposits of rare-earth elements (REEs) are exhausting all over the world, and it has become necessary to find new sources and methods for their extraction. In addition, increasing the application of REEs in modern technological society has increased its demand globally. One of the important movements to compensate for the future shortages of critical metals is the recovery of REEs from recyclable materials. This paper presents a review of the classification and extraction methods, as well as general applications of REEs with emphasis on secondary sources such as coal and coal byproducts, iron ore tailings, apatite, and phosphate byproducts. An overview of the current state of knowledge on the various methods of REE beneficiation and extraction is covered. These methods include physical separation, as well as hydrometallurgical and bio-hydrometallurgical techniques. The application of these REE extraction techniques for enhanced recovery has been driven primarily by the unique industrial application of these important elements. This paper further explores the existing and potential environmental challenges associated with REE extraction. The authors have presented a wide array of literature, in-depth discussion of the subject, and a succinct summary of processes and relevant case studies.

Sep 23, 2020

The New Zealand microcontinent is relatively well endowed with gold deposits; its past gold production per unit area of 3.2 kg/km2 ranks high on a world scale. Total recorded production (1857 - 1986) is about 854 000 kg and most of this gold was mined between 1861 and 1920. There has been a strong revival in gold exploration and mining since 1979, with exploration expenditure of around $15 million per annum and a declared gold production in 1986 of 1265 kg (886 kg in 1985). In addition to numerous alluvial gold recovery plants working small to medium sized deposits (mainly in Westland and Otago), there are five medium to large projects that have started production (Martha Hill), or have reached advanced stages of construction (Grey River dredge), permitting (Golden Cross and Macraes) or exploration (Globe-Progress). This summary paper is taken from reviews by Brathwaite et al (1986) and Brathwaite (1988).

Jan 1, 1988

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By J. W. Jensen

This report was prepared as a background reference for future publica¬tions concerning the damping capacity of metals and alloys. It contains a broad description of the theory and methods of measuring damping capacity and correlates the developments of the past decade in terminology, units, and techniques. Damping-capacity instrumentation at the Mississippi Valley Experiment Station, Rolla, Mo., is described. The bibliography contains over 150 references to recent articles, each tabulated as to material investigated and test variables, such as frequency, stress, mode of vibration, and temperature. INTRODUCTION After it discovered high-damping manganese-copper alloys before World War II, the Bureau of Mines began research on the damping capacity of alloys and has continued to expand this activity to the present time. In physical metallurgy, damping capacity has become an important research tool in the Bureau. The physical measurement of the damping properties of alloys was begun at the College Park laboratories, and later conducted at Salt Lake City under the direction of Dr. E. V. Potter. Among the many articles resulting from this work, Damping Capacity of Metals (108)3/ has received frequent men¬tion in more recent literature and describes briefly the methods of measurement employed at that time.

Jan 1, 1959

By D. F. Malan, Y. Jooste

"SynopsisScattered mining was practised on Kusasalethu Mine (previously Elandsrand Gold Mine) prior to 1998, but at deeper mining levels it was no longer feasible, since it would have resulted in unacceptably high stress levels and energy release rates. Longwall mining was not adopted at these depths as the mine required a more flexible mining method owing to the highly variable grade and the presence of geological structures. A mining method was developed that consisted of dip stabilizing pillars for regional support, as well as bracket pillars to clamp geological structures. A strict sequence of extraction was followed and this, together with the particular layout, was called the ‘sequential grid mining method’. This method addressed two key problems, namely negotiating adverse geology and the erratic grade of the Ventersdorp Contact Reef (VCR) orebody. However, a significant drop in production rates resulted in the need for alternatives and improvements to the original mine design. Modifications to the design were proposed in order to increase production rates, and an investigation to consider the rock engineering implications of these modifications was conducted. The study indicated that the modified method, called the ‘multi-raise mining method’, appears to be feasible and might address some of the production problems that were experienced with the original sequential grid design. An analysis of actual seismic data showed no significant differences between the original sequential grid mining and the implemented multi-raise mining. The numerical modelling of the mining layouts showed slightly higher interim energy release rates (ERRs) and average pillar stress (APS) levels during the extraction process. The final values are nevertheless identical to that of the original sequence. The study also investigated the use of a modelled moment method to analyse future seismic trends. The study illustrated that the expected seismic trends will be very similar for the multi-raise method compared to the original sequential grid mining method. This study is nevertheless considered of a preliminary nature and ongoing monitoring and analysis of seismic data at the mine is required to verify the response of the rock mass to the modified sequence and increased extraction rate. In particular, future work needs to investigate the effect of mining rate (advance rates in individual panels as well as volume of mining in particular raise lines) on the level of seismicity."

Jan 1, 2015

By Jack Curran

KANSAS CITY, MO - Performing one of the most impressive urban building-implosion projects in recent memory, Tulsa, Oklahoma-based Dykon Explosive Demolition Corp. and Omaha, Nebraska-based Anderson Excavating recently felled the landmark Columbia Bank Building in downtown Kansas City, Missouri, USA. Although every structural blasting project presents special challenges, this undertaking was most notable for its unusually unique structural design, tight clearances, and high risk to adjacent structures.

Jan 1, 2003

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The application of statistical analysis software programs has proven useful for the investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the US National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Jun 18, 2023

By Lynn B. Hales

There is a large economic opportunity associated with improving metallurgical performance in mineral processing plants that use process control. Thus, future control systems will be developed towards more sophisticated user friendly, computer-based systems that use powerful software analysis and control techniques. Auto-tuning, adaptive control and process models will gain expanded use because of their transparent availability to the system designer. Control of individual unit operations will be optimized and coordinated through expert systems that monitor economic conditions and management directives and direct operations accordingly. Plant areas, once considered cost centers, will be integrated into plant-wide control systems for economic control and optimization. This article looks at new control hardware, process sensors, control strategies and software development tools. It also looks at the economics driving the continued development of advanced process control systems. Process control systems routinely used in the mining industry were born when the microprocessor was invented. They have continued along an evolutionary path from vendor specific processing hardware and proprietary operating systems to computer industry standard "open architecture" systems. The many economic forces that drive the development and functionality of these process control systems will cause this evolutionary process to continue. Two of the broadest categories are the needs of the end users and the desire of the system manufacturers to distinguish their products from one another. More

Jan 1, 1994