Search Documents

By P D. Katsabanis

This chapter describes the principles for the derivation of the equations for a detonation wave. The importance of the equation of state for the detonation products is demonstrated and commonly used equations of state are discussed. Furthermore a brief introduction to the TIGER code is presented.

Jan 1, 1991

By R. W. Bee

This project, sponsored by the U.S. Bureau of Mines, Division of Environment, addresses two major subjects: refuse removal and subsidence monitoring. The refuse removal task consisted of developing a methodology for selecting the most economical combinations of coal mine breaker refuse and rock banks, disposal sites and material moving systems (trucks, trains, belt conveyers and pipelines). To prepare plans for moving refuse in the Lackawanna Valley of Northeastern Pennsylvania, refuse banks were inventoried, underground disposal sites identified and unit cost data prepared for the various material moving systems. The subsidence monitoring task consisted of defining the phenomenon of coal mine induced surface subsidence, establishing operational requirements, cataloging sensors and techniques to detect and measure subsidence and testing of the most promising techniques (photoelastic patch, tiltmeter, strain gage, microseismic and precise surveying). A preliminary system for a 700 acre area in Scranton utilizing 267 grid sensors, seven microseismic sensors and precise surveying techniques was designed with initial and annual operating costs determined. Two minor tasks supported both main subjects: zoning in the Northern Anthracite Field of Pennsylvania and Technology Transfer of subsidence vulnerability prediction techniques.

Jan 1, 1972

Since the last occasion on which I spoke to you on this subject there has been a considerable increase in the mechanical ventilation of Western Australian mines.The following table compares the figures for 1939 with those of 1941. The type of fan most commonly used is the limit load fan. On account of its higher mechanical efficiency it has very largely superseded the multivane fan with forward curved blades.Two fans of the propeller type are in use and these have given very satisfactory service. This type of fan also has a high mechanical efficiency particularly at the correct duty for maximum efficiency.The maximum efficiencies obtainable from the various types are, for "multivane" 670/0, for "limit load" 75%, and' for aerovane 7810/0.References to propeller fans with variable pitch have appeared in the technical press, but no detailed d~scription has been issued. The advantages of these fans for mine ventilation are not obvious. An aeroplane is required to operate over a wide range of duties, while the speed of the motor for maximum efficiency is pl'actically constant. In such circumstances the propeller can be adapted to the particular work it has to do by varying the pitch of the blades. In a mine the speed of the fan can be varied to suit.the conditions, and it would appear that variable pitch is not necessary while there is a reasonable range of fans to choose from.The question of the correct position for the fan still comes in for considerable discussion. Exhausting fans at the surface have the support of time and custom, and in many cases this represents the only reasonable arrangement. Such fans should be fitted with an evase, especially in the case of fans with a high outlet velocity such as the aerovane types.It is claimed that there are advantages in having the fan at the surface where it is readily available for inspection and maintenance. Experience has shown that these advantages are more apparent than real. Fans will run for long periods with no attention other than occasional greasing and cleaning, and modern electric motors will run without attention for very long periods.In some instances the expense of a power cable to take current to the fan may be saved by placing it on the surface, but in the majority of cases...

Jan 1, 1941

By K Cameron, S Strohmayr, J Wallace

In 2012, a single module heavy medium cyclone plant (HMP) was installed at the Glencore Zinc’s (then Xstrata Zinc) McArthur River lead zinc mine. The HMP formed the first part of the MRM Phase 3 Project to increase run of mine (ROM) capacity from 2.4 to 5.5 Mt/a.The purpose of the HMP is to remove liberated gangue from the crusher product at minimal loss of valuable mineral. The McArthur ores are very finely disseminated requiring a fine primary grind size prior to rougher flotation. Rejecting waste prior to grinding therefore offers significant power and grinding media savings. The plant was designed to treat only those ores with a reasonable upgrade ratio at the target zinc recovery across the HMP of 95%.On this basis, a 1.8 Mt/a single module plant was built based on 250 t/h feed rate and 82% availability. In contrast to existing base metal heavy medium plants in Australia, the MRM Flow sheet utilised the principles in modern coal heavy medium cyclone plant design. Since commissioning, the plant feed rate has been significantly increased and is now normally operated up to 540 t/h (dry basis).Although this throughput increase is partially due to debottlenecking work, it is also attributable to the conservative design parameters for base metal heavy medium cyclone circuits in comparison to those used in equivalent coal circuits.This paper discusses Flow sheet design and compares traditional base metal design parameters with those achieved at MRM and those of modern coal plants. It provides information on plant capital and operating costs and the net savings realised by its installation. In addition to power and grinding cost savings, the paper also highlights the savings in water through rejection of near dry waste and reduction of tailings pumped to the storage dam.CITATION:Wallace, J, Strohmayr, S and Cameron, K, 2015. McArthur River Mine heavy medium plant – the benefits of applying modern coal plant design principles to base metal heavy medium separation, in Proceedings MetPlant 2015, pp 311–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Two events during the past decade have combined to effectively alter the role of the geologist working in Papua New Guinea. The gold boom of the 1980s resulted in a substantial increase in the general awareness at village level of mining companies, gold and landowner issues, and as a consequence of the Bougainville tragedy, landowners are also very much aware of the potential problems of a mining operation in their area. Landowners know they have the power to remove a company from a project area, and government has shown itself to be virtually powerless and unable to help the company effectively. During a considerable proportion of a project's development time, the project geologist is viewed in the eyes of the local community as the 'company'. Good landowner relationships are nurtured over a reasonable time period and the input of the geologist is significant in determining the eventual fate of company-landowner relationships. The initial impressions of the company, gathered by the local community, will have a far reaching impact on the nature and direction of their future exchanges with the company.

Jan 1, 1991

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By William B. Plank

IN this paper are presented the results of a complete statistical survey of the enrolment, courses and degrees, and the employment situation of recent graduates in all of the 46 institutions in the United States, including Alaska, and four of the six schools in Canada that grant degrees in mineral technology. The data were collected by the writer by means of a questionnaire in December, 1933, to which all the institutions, except one, replied. Included also are data of a similar study made by the writer in May, 1933, for the S. P. E. E. summer session of mining and metallurgical teachers at the University of Wisconsin and published in the Journal of Engineering Education for December. 1933. Some of the data of a paper of the writer's entitled, "The Trend of Mineral Engineering Student Enrolment in the United States," read at the A. I. M. E. meeting on Feb. 16. 1931, are given for comparison. Acknowledgment is made to all the administrative officers of the institutions who took the time from their busy lives to supply the in- formation asked for. Their fine cooperation has alone made possible these two surveys with a completeness of detail never before attempted

Jan 1, 1934

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

By P. Samanta, Mohammed N. Azad, Gustad F. Taraporewalla, A. K. Mukherjee, Abhay S. Patra, D. Sachinraj

Beneficiation of coal is a water intensive process, and the water is recovered in downstream operations in the high rate thickener (HRT) and vacuum belt filtration (VBF). Clean coal particles entering the HRT have an inherent tendency to enter the overflow because they are extremely fine and hydrophobic. Hence, flocculants (polymers) are used to floc the ultrafine particles so that they settle and enter the underflow. Ultrafine coal particles (−37 μ), which are highly hydrophobic, if present in the stream, will not be efficiently captured by using flocculants alone. This is observed in the normal plant operation at one of the beneficiation plants in the Jharia region, Jharkhand, India. Approximately 6–7% of the feed to the HRT enters the over flow (supernatant water). Hence, this amount of clean coal particles is not recovered and account for production losses. A comprehensive settling and dewatering test work was conducted with clean coal slurry using several commercially available reagents. Studies were also done on different combinations of reagents, including coagulants and surfactants along with flocculants, to improve the settling behavior of the coal particles. The reagents were assessed based on their performance with respect to settling rates, overflow water clarity, and compaction of the underflow solids. Emphasis was given to the ability of the reagents in compacting thickener underflow to higher densities so that maximum water could be recovered from the thickener. Pretreatment of highly hydrophobic coal slurry with a combination of coagulant and surfactant followed by flocculation showed very good settling characteristics with clear overflow.

Sep 30, 2021

By I T. Ross

In the last 50 years there have been tremendous improvements in equipment used in development on underground mines. Compressed air powered jacklegs have been replaced by high powered electro-hydraulic drifters on sophisticated drill jumbos and load haul dump units have taken over from small shovels and rail cars.Despite the increase in power applied in key parts of the development cycle, average advance rates have fallen and costs have increased. The factor that is most often regarded as the main contributor to slowing advance rates is increased support requirements. Whilst there is no denying that the drive to improve safety has resulted in the requirement for more bolting and the installation of a skin support (mesh or shotcrete), this is not the only factor.Within the industry as a whole, many of the basic principles of development appear to have been lost over time. This paper looks at a historical case study and discusses some of the features of old development cycles that are no longer in use. This highlights some of the basics that appear to have been forgotten. These may be indicators to what may provide improvements in the conventional drill and blast development cycle.CITATION:Ross, I T, 2014. Development – back to basics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 67–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators' shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators' duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators' noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

This paper presents a resume of the likely profitable mining areas in New Zealand. It covers the main 'minerals' û gold, coal, oil and gas, ironsands, silica sands, clays, lump silica, perlite, sulphur and limestone. The potential mining projects are depicted on a map of New Zealand together with the associated works involved in hydro-electric and geothermal power development requirement for industries such as aluminium, nickel ferro-silicon or silicon carbide production. The political need for mining development to relieve unemployment and reverse emigration is stressed. A case is made for exploration and development assistance by government in labour re-training, energy supply and transportation, if the tremendous losses through lack of use of human and industrial resources are to be rapidly reduced. These losses are currently estimated at $10 000 000 000 per year. The need for protection of the sanctity of contract and security of tenure of all mining operations is touched on briefly as is the need for a reasonably balanced view on conservation. However, as both of these are more properly covered in papers on the legal and environmental aspects of the mining climate, they are presented here only as they affect the economy of the mining operation. Finally, there is a brief comment on the mining climate in New Zealand relative to Australia and South Pacific mining operations.

Jan 1, 1990

By P. W. Jensen

Gold deposits in Interior Alaska are commonly coincident in time and space with reduced, mid-Cretaceous granitoids. The True North deposit of the Fairbanks district is several km from such granitoids, but yields mineralization ages indistinguishable from the Fort Knox granite-hosted deposit. True North, however, resembles sediment-hosted epithermal Au, demonstrating the variability of intrusion-related Au deposits in metamorphic rocks. The True North deposit (14M tons at 1.5 gpt) is hosted within a carbonaceous thrust complex separating eclogite facies from amphibolite facies rocks, located > 5 km from mineralized granite outcrops. The ores contain anomalous Sb, As, and Hg (stibnite is the most common sulfide) with ankerite-sericite alteration in steep NE-striking ?feeder? shears and low angle thrust shears. Nearest hornfelsed rocks are located > 1 km away, and across several high-angle faults. Fluid inclusion data indicates trapping temperatures of ~250C from low-density, low-salinity fluids at P < 0.5 kb. Au was originally present as solid solution in sulfides; minable ores are restricted to the oxidized upper 100 m of the deposit. The considerable differences between this deposit and the temporally equivalent Fort Knox intrusion-hosted deposit indicate no one description adequately characterizes this deposit type.

May 1, 2003

By Ernest M. Spokes

For bituminous and lignite coals the economic picture continued to improve as it has each year since the low of 1961, with production at 480 mil- lion tons in 1964 compared with 1963&apos;s 459 million tons. The anthracite industry produced 16.3 million tons in 1964 and 18.3 million tons in 1963. The industry is looking toward a further expansion; among the new developments will be a mining wheel producing 3 million tons of lignite per year in South Dakota. It is expected that electric power generation will continue to provide the market for most of the increase in consumption, with exports second in importance in the expansion. Improvements in methods of mining and transporting coal underground and in strip mines, and the cooperation of carriers in finding ways to reduce transportation costs to distant markets, have made possible these expansions. Research continues to reduce costs of mining, transportation, steam generation of electric power and production of steam for space heating and manufacturing processes, to retain some markets and expand others. Other research seeks to expand markets by developing fuel from coal which will be more attractive than competing fuels, by reducing sulfur and other sources of air pollution. Public relations efforts of the industry are bearing fruit in a greater acceptance of coal as a modern fuel.

Jan 2, 1965

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor&apos;s field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By M. W. Von Bernewitz

Fay&apos;s glossary3/ of terms contains the following definition of "black sand": Heavy grains of various minerals which have a dark color and. are usually found accompanying gold in alluvial deposits, for example, magnetite, chromite, ilmenite, cassiterite, tourmaline, and others. The Bureau of Mines is issuing this report in answer to the many inquiries from individuals and firms as to how they may treat or sell the heavy black sands that accumulate in the sluice boxes of beach and river placering and to warn such individuals and firms against becoming too enthusiastic over the chances of striking it rich. For a half century or longer much money, energy, and time have been wasted in devising, building, and trying numerous machines to recover gold and platinum, also gem stones, from sand that generally has not been worth the effort. Volumes have been written on the subject, and thousands of letters of inquiry have been received by agencies of the State and Federal Governments. The demand for information has been so great that all of the Bureau&apos;s publications dealing wholly or partly with black sands are out of print. They are listed at the end of this report.

Jan 1, 1938

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

By M. C. Harris

The past twenty to thirty years have seen unprecedented research activity aimed at understanding the performance of flotation froths. In 1990, Finch and Dobby coined the term froth recovery factor, Rr, to represent the efficiency of the froth in delivering particles from the pulp-froth interface to the concentrate. Originally defined for flotation columns, Rr has also been found useful in modeling mechanical flotation cells, and a number of techniques, based on quite different approaches, have been developed for measuring the froth recovery in industrial flotation cells. None of these techniques is universally successful. This paper reviews the concept of the froth recovery factor, and the basis of each of the techniques that have been proposed to measure Rr, and examines the reasons for this parameter being so difficult to pin down. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

The Mahakipawa gold deposit is located 21 km northwest of Blenheim. It became the site of a small hardrock gold rush in 1889 following nearby alluvial gold discoveries in 1888. The study investigates the geology of the area of hard rock mining in the vicinity between Cullens and Waikakaho Creeks. The Marlborough Schist which hosts the gold depos, it consists of polydeformed greenschist facies quartzofeldspathic psammitic, pelitic and volcanigenic schist.

Jan 1, 1993