Search Documents

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By J. -H. Wu, S. Nishiyama, Y. Ohnishi

The behaviors and stress distributions of the inclined jointed rock masses with different dip angles obtained from DDA are compared to the results of laboratory tests. By calculating the block stress distributions, it is confirmed that DDA can reproduce the arching around the trap door when lowering the trap door. The shapes of arching change with the angles of inclined layers. In addition, the earth pressures acting on the trap door shows non-symmetrical distributions when the layers are not horizontal. The stress concentration occurs in one side of the rock masses close to the trap door. Furthermore, the surface settlements are also related to the inclined angle, and the loosening zone in rock masses can be different from Terzghi’s theory [1]. Since, simulations have good agreements with the laboratory test , it demonstrates the applicability of DDA to explain the mechanical behaviors of tunnel, such as arching phenomenon, non-symmetrical earth pressure distributions acting on the trap door, and the surface settlement profile in the jointed rock masses. Dans cet article est décrite l’étude numérique du perçage d’un tunnel dans un massif de couches rocheuses jointes inclinées. La simulation à l’aide de l’Analyse de Déformation Discontinue (DDA), en faisant varier l’angle d’inclinaison des couches de roche, nous apporte des résultats en termes de distributions de contraintes et de comportement des couches, résultats qui sont ensuite comparés avec des résultats de tests en laboratoire. Les résultats confirment le fait que la DDA est capable de reproduire le phénomène d’arcage autour de la trappe lorsque la trappe s’abaisse. Les formes d’arcage varient selon l’angle d’inclinaison des couches de roche. Par ailleurs, lorsque les couches ne sont pas horizontales, la distribution de pression agissant sur la trappe est assymmétrique. La concentration de contraintes se produit du coté proche de la trappe. De plus, les tassements de surface dépendent eux aussi de l’angle d’inclinaison. En conséquence, les résultats de simulation sont en accord avec les tests en laboratoire, ce qui prouve que la DDA permet d’expliquer des comportements mécaniques du tunnel tels que l’arcage, les distributions assymmétiques de pression du sol sur la trappe, ainsi que le profil du tassement de surface dans la masse de roches jointes. Dieser Beitrag beschreibt eine numerische Studie über Tunnel im geklüftetem Fels. Das Verhalten und die Druckverteilungen in den unterschiedlich geneigten und geklüfteten Felsenmassen wird mit Hilfe des Discontinuous Deformation Analysis Programms (DDA) simuliert, und mit Laborversuchen verglichen. Die Resultate bestätigen, dass DDA der Gewölbewirkung im „Trapdoor“ Experiment gut reproduzieren kann. Die Form des Gewölbes, ändert sich mit unterschiedlichen Neigungswinkeln der Schichten. Bei geneigten Schichten entstehen unsymmetrische Druckverteilungen. Auch die Oberflächenabsenkung ist von dem Neigungswinkel abhängig. Die gute Übereinstimmung der Simulationen mit den Laborversuchen zeigt, dass die DDA-Methode gut geeignet ist, um das mechanische Verhalten von Tunneln, wie z.B. den Effekt der Gewölbewirkung, die unsymmetrischen Druckverteilungen bei geneigten Schichten, oder die Oberflächenabsenkung in geklüfteten Felsenmassen, zu erklären.

Jan 1, 2003

By Rolf Birger Pedersen, Alden Ross Denny

"Synthetic Aperature Sonar (SAS) is a powerful tool for ultra-high resolution marine survey. The Kongsberg HiSAS system deployed on the HUGIN AUV has a rangeindependent resolution of 3x3 cm for sonar image and ~10x10cm for the interferometric bathymetry product [1]. This resolution is achievable for areas up to 50 km2 on a single survey mission providing huge multi-attribute datasets. This technology, originally designed for military and oil-industry applications, has the potential to revolutionize scientific seafloor mapping. The extreme resolution of this technique allows for deposit mapping in and around seafloor hydrothermal systems, including the discovery of extinct venting structures. By clearly distinguishing between volcanic and hydrothermal landscapes based on features below the resolution of conventional multibeam systems, SAS enables an entirely new level of hydrothermal deposit survey. Additionally due to the extreme resolution of this survey technology, repeat survey and change detection should allow centimeter-scale changes in deposit morphology to be routinely detected over an entire hydrothermally venting region. In collaboration with the EU funded MIDAS project, the Centre for Geobiology at the University of Bergen will deploy the HUGIN AUV this summer at two distinct shallow venting systems on the Arctic Mid-Ocean Ridge system. The AUV will collect repeat bathymetry at the Jan Mayen Vent Field, and extend the SAS coverage to include newly discovered venting sites. We will present the preliminary findings of this expedition, including the first deposit estimations made from full-resolution SAS mosaics."

Sep 1, 2014

The stratigraphy of the Western Coalfield is briefly reviewed and the important units of the Lithgow Coal Measures, particularly the coal seams, are defined. The possibility of coal measures of Tomago age ocurring near the edges of the Sydney Basin is discussed onpresent evidence.Using data obtained from unpublished drilling records, detailed structural, isopachous and lithofaeies maps have been drawn. These show that the structure of the coal basin has been influenced by the underlying basement in many ways.The prominent jointing in the overlying Triassic sandstones is discussed in relation to jointing in the coal measure sediments.It is concluded that in addition to the general knowledge obtained with respect to the coal basin, useful information regarding coal quality and quantity can be gained by the study of broader sedimentary and structural features.INTRODUCTIONThe term "Western Coalfield" covers approximately the area from Katoomba to Rylstone, together with the smaller, separate Ulan area (Fig. 1). The area studied is part of the great sedimentary Sydney basin named by Osborne (1948). The first discovery of coal in Sitlt in the area was made in 1824 by Andrew Brown, although George Bass noted the presence of coal float in the Grose River in 1797. Production is recorded from the Western Coalfield in 1838 but mining was intermittent until 1868 when mines in the Lithgowvalley (producing coal from the Lithgow Seam) came into production. In 1882 the Katoomba Seam was first worked at Katoomba.The work of J. E. Carne (1903, 1908) defined the limits of the Coal Measure sediments and also contributed a great amount of valuable detailed information about the region.

Jan 1, 1960

By D. B. Rebuli

Seismic networks in deep gold mines of South Africa are often planar owing to the tabular geometry of the orebody and, therefore, the mining infrastructure. Consequently, seismic event locations are poorly constrained in the direction perpendicular to the reef plane, and symmetrical locations above and below the reef plane may fit the observed data equally well. This problem may be resolved in situations where the strata above and below the reef plane have significantly different seismic velocities, which is the case for the Ventersdorp Contact Reef at Kusasalethu mine (previously Elandskraal, the amalgamation of Deelkraal and Elandsrand). A location method using a layered location model that takes into account the velocity contrast between the layers was tested. Observed direct- and head-waves were used to determine the velocity bounds of the P-wave velocities in the two-layer model. The data-set was also used to find the best P- and S-wave velocities for the two layers by grid searching over a range of velocities and minimizing the sum of the travel-time residuals. The results from the grid search and those from the calibration of velocities using direct- and head-waves give similar P-wave velocities for each of the two layers. A second set of seismic events was then relocated with this layered model and locations closer to reef were found. This simple layered location method goes some way to reduce the reefperpendicular location errors for Kusasalethu mine in particular. Keywords mine seismology, velocity model, location methods.

Jun 1, 2013

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

By David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air-blast levels and measurement methods are equivalent in terms of structure response, and anyone could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must he used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to preclude damage to residential structures and any possible human injury over the long term.

Jan 1, 1980

By C. Lottering

Copper sulphate solutions are produced during the pressure leaching of first-stage leach residue in a typical base metal refinery process. Apart from impurities such as selenium and tellurium, this leach solution also contains other precious metals (Rh, Ru, and it) due to dissolution in the pressure leaching stage. Selenium and tellurium are removed from the leach solution by precipitation with sulphurous acid, since these elements negatively affect electrowinning. This study investigates the feasibility of modifying the Se/Te precipitation process step to achieve significant rhodium precipitation in addition to selenium and tellurium precipitation, in order to reduce the rhodium inventory of the process. Thiourea, S02, formaldehyde, formic acid, and sodium thiosulphate were evaluated to determine which of these reagents would achieve the highest Rh precipitation. Based on these screening tests, SO2 and thiourea were selected to be used as precipitation reagents in optimization tests. During these optimization tests, the operating temperature (80 to 150°C) and the amount of reagent added (80 to 140 per cent excess) were varied to evaluate the effects that these operating conditions have on the precipitation behaviour of Rh as well as Se, Te, Cu, and Ni, and to propose appropriate operating conditions. It was found that thiourea resulted in good Rh and Se precipitation (typically in excess of 90 per cent), but precipitated noticeably more copper and nickel from the solution than when SO2 was used. In addition, thiourea had poor Te removal characteristics. SO2 achieved a maximum of 70 per cent precipitation of the rhodium. Faster kinetics and a larger extent of Te precipitation were, however, observed when using SO2 compared to thiourea.

Jan 1, 2012

By S. Ganguly

Slag samples taken from adjacent to the furnace wall of a submerged arc ferromanganese smelting furnace have been found to contain high concentrations of K2O. To characterize the phase equilibria relevant to these slags experimental studies have been carried out to determine pseudo-ternary sections of the form ?MnO?-CaO-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.65 and 6.0 wt% K2O for temperatures in the range 1523-1673 K. In the pseudo-ternary section investigated the primary phase fields are found to be mullite, 3Al2O3?2SiO2; corundum, Al2O3; spinel, MnO?Al2O3; manganosite solid solution, (Mn,Ca)O; dicalcium silicate,2CaO?SiO2; gehlenite 2CaO?Al2O3?SiO2; anorthite CaO?Al2O3?2SiO2; kalsilite KAlSiO4 and leuciteKAlSi2O6. It was found that the presence of K2O in the slag decreases liquidus temperature in the anorthite and gehlenite primary phase fields. The manganosite primary phase field is expanded in the direction of increased (Al2O3+SiO2) and the liquidus temperatures in the manganosite primary phase field are increased significantly with the presence of K2O in the slag.

Jan 1, 2007

The need to hoist increasing loads from great depths is leading to the more general adoption of winders of the Koepe and Blair types. The trend has introduced a number of new problems in winding ropes, more particularly in the Koepe system where regular destructive tests during the life of a rope are not possible. Consequently, the importance of introducing non-destructive tests is much greater, especially so in the case of Koepe ropes used for deep winding where there are three major destructive fatiguing influences. These are rotational effects when a vertical rope is changed end-for- end each trip, the much greater range of stress to which the rope is subjected each trip as compared with drum winding, and the destructive effect of a high coefficient of friction between wheel and rope. A plea for a lower coefficient in the interest of better rope and tread life, substantiated by analysis, is made for Koepe winders operating at depth.Co-ordination of rope testing with general hoisting problems is stressed and the active participation of the Wire Rope Committee of the Australian Mineral Industries Research Association Ltd. in the promotion ofthe project is noted.The general introduction of a rope testing programme in Australia, personnel requirements and some local basic research in the subject to cope with future demands are considered.

Jan 1, 1967

By Drupad B. Desai, Bruce Chang, Jay L. Merritt

This paper reviews difficult ground conditions encountered along the alignment of large-diameter sewage tunnels for the City of Los Angeles. It offers a detailed one-of-a-kind solution to a unique problem for shallow urban underground tunnels in a seismic zone, using state-of-the-art materials, technology, and equipment. The following topics are discussed in detail: • Geotechnical Design consideration for tunnel traversing through an active fault zone. • Seismologist evaluation of possible fault-offset problems where a fault zone crosses the alignment, in the event of an earthquake of moment-magnitude 6.5. • Probability analysis regarding "recurrence interval." • Structural design of tunnel subjected to displacement, subjected to axial elongation or shortening, and capable of rotational freedom. • Special joint details.

Jan 1, 1989

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By Evelynn Stirling

Agenda ? Emissions legislation ? Cummins Tier 4 Technology ? Cummins Experience with Technology ? Operation and Maintenance Impact The Emissions Challenge ? The 2014/5 emissions regulations present the most significant challenge to our customer?s diesel powered equipment design and operation in recent history? ? ?and Cummins has the solution.

Aug 1, 2013

By Peter D. Bell

The paper describes the geology of the gold deposits of the Yanacocha district, Northern Perú. The Yanacocha District is located 20 km north of the city of Cajamarca, whose deposits are located in the Andes of norther in Perú. Gold production may have occurred as early as Incan times, but modern exploration that began in the 1960’s targeted only copper and silver. Current mining is entirely by open pit methods with heap leach recovery. Production in 2003 was from the Cerro Yanacocha deposit and the La Quinua fluvioglacial deposit. La Quinua is not discussed in detail in this report. However, Yanacocha is described as a high-sulfidation epithermal deposit occurring in pyroclastic rocks. The success of Yanacocha has made this type of target among the most sought after by exploration companies worldwide. The important characteristics of the geology of Yanacocha are reviewed below, along with some specifics of exploration techniques used in the district.

Sep 12, 2005

By Y. Ichihara, H. Matsumoto, K. Itakura, H. Eguchi, G. Deguchi, K. Sato

Mechanical data from a rockbolt drilling machine, such as torque, thrust, revolution and stroke, are useful for understanding the geological and geomechanical conditions around roadways and hence selecting the optimum bolt type and density. Laboratory experiments showed that the level of torque or thrust reflects differences in rock type, with separation of strata and cracks appearing as a specific pattern. Algorithms of neural networks based on adaptive resonance theory and back-propagation were used to extract the pattern and estimate the location of discontinuities. For field testing in an underground coal mine, a prototype data acquisition system was attached to a portable drilling machine. Several sets of logging data from one locality were combined to construct a two-dimensional model of the strata, from which the slope angles of discontinuity faces could be estimated

Jun 19, 1905

In all the industries that require blasting operations using explosives, there exists numerous unwanted side effects of the blast which may pose as environmental hazards. These hazards face prominence, especially in India, where there are very stringent rules and regulations governing the use of explosives. The environmental hazards associated with blasting operations as a whole can be tacked successfully to a certain extent depending upon the ultimate expectations of ,the post-blast effects and the limitations of the environmental obligations as specified by the authorities from time to time and from place to place. The main parameters which require attention to limit the post-blast results to the optimum level are ground vibrations, dust pollution, gas pollution, air blast effects, noise pollution & fly rocks etc.

Jan 1, 1995

By H. R. Butler, J. F. Church, A. T. MacGibbon

Introduction Inco is the major North American nickel producer. Initially based in Sudbury, Ontario, its past exploration activity was directed toward finding new nickel deposits. New nickel sulfide discoveries outside Sudbury have included Thompson, Manitoba; Shebandowan, Ontario; and Widgiemooltha in Western Australia as well as a host of nickel laterite deposits. The company is currently diversifying into other commodities, including gold. Inco's exploration department participated in uranium discoveries in Saskatchewan and chromite discoveries at Tiebaghi in New Caledonia. In addition, it found new gold deposits at Lupin, Northwest Territories; Crixas, Brazil; Hoyle Township, Ontario; and Casa Berardi in Quebec. Crixas and Casa Berardi are currently being evaluated by underground exploration. Figure 1 shows some Canadian Shield gold locations where Inco is or was an active participant. Base metal developments Base metal exploration in shield areas has been greatly eased by applying scientific studies. Archean nickel sulfide deposits have been found using komatiitic-flow models (Fardon, 1971). Volcanogenic massive sulfide model has been applied to copper-zinc deposits (Sangster and Scott, 1976). Such deposits were subsequently seen developing on the sea floor through black smokers (Spiess, MacDonald, and Atwater, 1980). Sedimentary processes were recognized early as important in ore formation, particularly in the southern hemisphere (King, 1976). And many ore deposits are now regarded as a simple part of the geological column (Stanton, 1960 and 1972). Petrographic work on alteration patterns in and around ore bodies was used to develop standard porphyry copper models (Lowell and Guilbert, 1970). Epithermal models for precious metals followed. Stratigraphic zonation patterns have been formulated for base metal deposits, including keel facies, ore facies, and cap or distal facies. Gold developments The work on base metal deposits naturally spilled over into precious metal exploration when the gold price was allowed to float on world money markets. Early work on elements associated with gold deposits, especially arsenic, tellurium, selenium, and mercury, pioneered more detailed geochemical work (Bagby and Berger, 1985; and Groves, Ho, and Houstoun, 1984). Geochemical patterns have been recognized around microfine gold deposits. And the study of gold precipitation patterns in modern geothermal systems has helped understand gold deposition. In the late 1960s and early 1970s, it was noticed that numerous Archean banded iron formations contained anomalous gold values. From this and other observations, the syngenetic exhalite gold model has developed. Gold deposits also occur along shears in some plutons such as the Belmoral mine in Quebec. This indicates the importance of epigenetic processes in ore formation. Shield ore settings Initial studies recognized that the major gold camps in the Canadian Shield were mostly in greenstone belts and found along "breaks," especially zones of faulting and sedimentation. Gill (1948) wrote, "Only recently, as a result of detailed mapping, has the importance of major schist zones such as the Larder Lake, Cadillac, Porcupine Creek, and Destor Breaks been recognized. These zones of persistent adjustment mark broad belts favorable for ore occurrence." The importance of shearing in ore location and regional greenstone stratigraphic position close to late sedimentary packages was clearly understood. And structural models have been further developed for some Canadian ore deposits (Hubert, Trudel, and Gelinas, 1984). In the Beardmore-Geraldton camp of northwest Ontario, the importance was soon recognized of fold noses in banded iron formation, as localizers for gold ore. This importance had also been recognized in Western Australia,

Jan 2, 1987

By F K. Buckley

Currently, Kanieri Gold Dredging Limited operates the only large scale gold dredging operation in New Zealand. It dredges a claim in the Taramakau River using the bucket dredge 'Kanieri'. This dredge, a 'Yuba' type, was designed and built in the 1930s. On the current claim it works about 12 hectares of ground a year. Because of its design, the tailings from the 'Kanieri' make land restoration difficult. This was unimportant until it commenced its new claim ML-32-310 in 1978. The conditions, attached to this licence required it to restore the land for afforestation, the designated use fur the Crown land being mined. With the company planning to work future claims on the Grey River, it decided to undertake restoration work on the Taramakau to demonstrate its capability of establishing pasture land on tailings, a more difficult task than restoring the land for afforestation. After two years and the restoration of two blocks totalling 22 hectares, reasonable pasture establishment has been achieved. Much has been learned to date and further refinement of the techniques used will take place over the next two years. The quality of the tailings produced has improved as a result of the limited modifications possible on the existing dredge. This has been significant in achieving better results. The knowledge gained will be taken into account in future dredge design. Both the Company and its Consultant are confident of achieving satisfactory restoration of dredge tailings for pasture land.

Jan 1, 1981

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987