Search Documents

By R. D. Yancich

A case study of longwall mining surface subsidence was performed at a mine in Southwestern Pennsylvania. The mine operated in the Pittsburgh coal seam which averaged 70-72 inches with 6-8 inches draw slate in the longwall location. The average overburden depth ranged from 625 8eet to 660 feet. Three adjacent longwall panels were studied and classified as Panel 1, Panel 2, and Panel 3. The following is information on each and can be seen on the General Mine Map (Fig. 1).

Jan 1, 1984

Unrelieved residual strains can influence the states of stress in rock masses. If cheap, stable structures are to be constructed in Tock in which large pressures are exterted by unrelieved residual strains, the pressures must be either utilized or neutralized. A photoelastic technique has been used to show that the release of residual strains in rocks is influenced by the mechanical properties of anisotropic rock fabrics. The relationships between directions of residual strain release and the attitudes of minor geological structures have been determined. For engineering design purposes it is possible to estimate the principal stress directions in rock containing unrelieved residual strains if the attitudes of such minor geological structures as foliation planes, lineations, and joints are known.INTRODUCTIONQuarry workers have long been aware that near-surface rocks may be highly stressed. In many cases the stresses are too large to be the result of gravitational loads. Dale (1923, pp. 34-35) gives many instances of deformation produced by the violent release of residual strains in quarry rocks. Coates (1963) has described powerful rock bursts and cases of rock deformation underground implying the existence of much larger stresses than are likely to result from present-day gravitational loads. The only explanation is that pressures of up to several thousands of pounds per square inch may be caused by unrelieved residual strains in rock.Instruments have been developed for measuring states of stress in rock masses. Most stress determinations in rock have been made on the assumption that rock behaves as a simple elastic material. It is now known that rock is a...

Jan 1, 1964

By P. Lefebvre, J. Sargent, K. Major, B. Darnton

"Stillwater Mining commenced mining operations at Nye, Montana in 1987 for the recovery of platinum and palladium. Exploration identified that the J-M Reef extended for 43 km. In 1998 Stillwater Mining made the decision to develop the East Boulder mine complex, located approximately 13 miles from the Stillwater mine complex at Nye, to increase production. This paper describes the design, construction, and start-up of the East Boulder process plant.INTRODUCTIONStillwater Mining Company have been producing Platinum and Palladium from their Nye, Montana operations since 1987. The mine production from Nye had been increased in stages with mine production being delivered through several portals and one vertical shaft.The deposit is narrow veined which prevents the application of bulk mining methods and thus limits the production capabilities.In order to increase the production of platinum (Pt) and palladium (Pd) Stillwater made the decision to access the ore from the J-M Reef from the East Boulder site. The East Boulder mine site is located about 21 km (13 miles) from Nye, however as shown in Figure 1, the travel distance is closer to 188 km (114 miles). Distance, on strike, and space availability at Nye precluded the expansion of the Nye concentrator to handle the increased mining rate and supported the decision to install a new concentrator at East Boulder."

Jan 1, 2003

By Andy Mille

The paper highlights development of tunneling methodology in the UK during the years 1990-2000 using the example of two major tunneling contracts where there solution of difficult tunneling problems during construction has benefited the industry as a whole. The paper deals with specific difficulties on two Contracts. The London Water Ring Main 80 kms (50 miles) long tunnel average internal diameter 2.54 m (9 ft4 in) and the Brighton Stormwater Tunnel 5.2 km (3.2 miles) long tunnel with an internal diameter of 6 m (19 ft 8 in). The results of human endeavour and technological innovations will demonstrate the giant strides made in tunneling methodology in the last decade of the 20th Century.

Jan 1, 2001

By William D. Dodge

A typical quality program plan is presented for explosion-proof (XP) electrical enclosures. The plan is suggested for manufactures of XP enclosures which are to be certified by MSHA for mining use. The plan describes the quality system, organization and implementing mechanisms which are to be applied in the manufacture and delivery of certified XP enclosures. Example forms and example procedures are included.

Jan 1, 1984

By K L. Brown, J L. Mauk

Sulfide-rich scale occurs in steam and water lines at the Ohaaki geothennal field,Taupo Volcanic Zone, New Zealand. Precious metals show very high concentrations around areas ofpressure reduction (Au 15500 ppm, Ag 68800 ppm). Pyrrhotite dominates at the orifice plate due to low PH2s1PH2 conditions. Sulfide mineralogy in the scales is consistent with alteration mineralogy of the reservoir rocks. Separated steam then produces a mainly pyrite/magnetite mineralogy, with lesser chalcopyrite, where textures reflect high flow rates and high levels of supersaturation. This study outlines the effect that pressure and subsequent temperature decreases have on the mineralogy, chemistry and textures of sulfide scales.

Jan 1, 1998

By A. Thoraval, K. B. Slimane, O. Ozanam

The REP experiment is part of the research programme conducted by Andra to investigate the possibility of reversible radwaste disposal in a Jurassic (Callovo-Oxfordian) argillite formation at the Meuse/Haute-Marne underground laboratory site in northeastern France. The experiment focuses on the hydromechanical response of the formation to sinking the laboratory access shaft. Modelling of boreholes and shaft sinking operations has helped to optimise measurement point locations based on initial stress tensor anisotropy, while minimising interaction between instrument boreholes. Analyses were made of model sensitivity to intrinsic rock characteristics, hydromechanical coupling properties and sensor installation procedures. L’expérimentation REP fait partie du programme de recherche pluridisciplinaire engagé par l’Andra pour étudier la possibilité d’un stockage réversible des déchets radioactifs dans la formation Callovo-Oxfordienne des argilites du site de Meuse/Haute-Marne (Commune de Bure - France). Cette expérimentation permettra d’étudier la REponse hydromécanique de la formation aux sollicitations engendrées par le fonçage du Puits d’accès du laboratoire souterrain de recherche. Afin d’optimiser le positionnement des points de mesures, compte tenu de l’anisotropie du tenseur des contraintes initiales, et de minimiser les interactions entre les forages d’instrumentation, des modélisations des forages et du creusement du puits ont été conduites. Des analyses de sensibilité aux caractéristiques intrinsèques de la roche, aux propriétés de couplage HM et aux protocoles d’installation des capteurs ont été faites. Die REP-Untersuchung ist Teil des multidisziplinären Forschungsprogramms, das die ANDRA im Callovo-Oxfordian-Tonstein in situ am Standort Meuse/Haute Marne (Gemeinde Bure – Frankreich) im Hinblick auf eine Eignung zur reversiblen Lagerung radioaktiver Abfälle durchführt. Dabei soll das hydro-mechanische Verhalten der Formation auf die Beanspruchungen, die durch das Abteufen des Zugangsschachts zum Untertage-Forschungslabor erzeugt werden, untersucht werden. Zur optimalen Positionierung der Messpunkte unter Berücksichtigung der Anisotropie des Tensors der Ausgangsspannungen und zur Minimierung der gegenseitigen Beeinflussung der Instrumentierbohrungen wurden ein Schachtabteuf- und Bohrmodelle entwickelt. Zur Untersuchung der inhärenten Eigenschaften des Gesteins, des gekoppelten HM-Verhaltens und der Installationsprotokolle der Messsonden wurden Sensibilitätsanalysen durchgeführt.

Jan 1, 2003

By A Harris, N Fitzpatrick, F MacCorquodale

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Gosowong epithermal Au-Ag deposits, located on the island of Halmahera, North Maluku Province, Indonesia, are owned and operated by PT Nusa Halmahera Minerals, a joint venture between Newcrest Mining Limited (75 per cent) and PT Aneka Tambang Tbk (25 per cent).The Gosowong deposit was a greenfields discovery in 1994. Subsequent brownfields discoveries, most recently in 2009, have resulted in a total endowment of more than 6 Moz Au. The three main deposits include Gosowong, Toguraci and Kencana, and as of December 2013, production comprised 5.7 Mt Au at 24 g/t for 4.3 Moz with remaining resources of 4.2 Mt Au at 13 g/t for 1.7 Moz.Mineralisation primarily occurs in multistage veins, breccias and stockwork veins, with at least four texturally- and mineralogically-distinct vein events, including: banded crystalline quartz, quartz-adularia, quartz-chlorite and quartz-sulfide stages. Vein mode, texture and mineralogy are zoned around areas of maximum dilation, vein width and vein grade. Within banded quartz-chlorite, grades of >1000 g/t Au are common. Anomalous Au-Ag-Pb-As-Sb-K-Li geochemistry in rocks is commonly associated with the epithermal mineralisation. Four major types of hypogene alteration are recognised at Gosowong: silicification (quartz-illite-adularia-pyrite) within the immediate vein zone, argillic (illite-quartz-pyrite) alteration enveloping the vein zone, advanced argillic (dickite-kaolinite-quartz) alteration above and adjacent to the vein zone and within the overlying Kayasa Formation, and propylitic (chlorite-epidote-albite-calcite-pyrite) alteration within the footwall and distal to the vein zone.CITATION:Fitzpatrick, N, Harris, A, MacCorquodale, F and Wardiman, D, 2015. The Gosowong goldfield – a world-class epithermal gold-silver district in Indonesia , in Proceedings PACRIM 2015 Congress, pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S. R. Amos, N. O. Lotter, A. L. Hannaford, J. F. Oliveira, D. W. Broughton

"Ivanplats Ltd appointed Xstrata Process Support to perform the flowsheeting development work for their hypogene and supergene geomet units of the Kamoa Copper deposit, located in the Democratic Republic of the Congo. Through systematic flowsheet development using modern Process Mineralogy, the optimised milestone flowsheet delivered a saleable concentrate grade of 32.8% Cu at 85.4% recovery with hypogene ore, and a saleable concentrate grade of 45.1% Cu at a recovery of 83.4% for supergene ore. The significant value of this development is that a single flowsheet will treat both hypogene and supergene ores and produce saleable concentrates. Further work to advance the flowsheet performance has been identified for investigation in the near future.INTRODUCTIONLocation and Description of the Kamoa DepositThe Kamoa copper resource is located some 40 km west of the city of Kolwezi, in the south west of the Katanga Province of the Democratic Republic of the Congo, in the region of Central Africa. Drilling at Kamoa in 2008-2009 had discovered laterally continuous, sediment-hosted, high-grade stratiform copper mineralisation in a newly discovered copper district that forms a previously unrecognised western extension of the famous Central African Copperbelt – which hosts such world-class deposits as Kolwezi, Tenke-Fungurume, Konkola and Nchanga. This discovery showed that the western end of the Copperbelt in the Congo does not terminate at Kolwezi (Friedland & Broughton, 2009). The resource contains hypogene and supergene geomet units with a transitional zone located inbetween the (upper) supergene and the (lower) hypogene. In the hypogene unit, the major copper sulphides are bornite, chalcopyrite and chalcocite, whilst in the supergene, the sequence is led by chalcocite, then bornite, and finally chalcopyrite. Covellite is present in both units as a minor copper sulphide. Both geomet units will be mined and treated in one concentrator, either as blends or as campaigns."

Jan 1, 2013

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By Messenger A. J, Miles J. G

A thermal neutron irradiation technique using a mCf neutron source has been developed and applied to thp.simultaneous determination of iron and aluminium (expressed as AI2O3) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt.While the determination of iron with this technique is based on the use of a NaI(TI) detector to monitor the characteristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the etermination of AI2O3 is based on the use of a second Nal(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the AI2O3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing.Dynamic trials of the technique, using 1500 kg samples of ore on a 460 mm-wide rubber conveyor belt moving at 1.7 m/min, have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% AI2O3. At the present stage of development, it is recommended that lump ore be crushed to a particle size of 6 mm before analysis.In addition to iron and AI2O3 determinations, measurements of total moisture content and bulk density are possible. The determination of Si02 is also feasible, but a separate fast neutron source (e.g., Am-Be) and a separate gamma ray detector are required.

Jan 1, 1980

By A. G. Pasamehmetoglu, N. Celebi, K. Erarslan

A deposit evaluation system has been developed for a proposed new mine in the basin around Collolar in Turkey. It includes compositing, gridding and reserve estimation facilities and takes account of the economic value of the pit and the pit bottom elevation

Sep 1, 1991

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006

By Thomas G. Goonan

Copper production through smelting generates large volumes of material flows. As copper contained in ore becomes copper contained in concentrate to be fed into the smelting process, it leaves behind an altered landscape, sometimes mine waste, and always mill tailings. Copper concentrate, fluxing materials, fuels, oxygen, recyclables, scrap and water are in-puts to the process. Dust (recycled),gases — containing carbon dioxide(CO2) (dissipated) and sulfur dioxide (SO2) (mostly collected, transformed and sold) and slag (discarded or sold) — are among the significant process outputs. This article reports estimates of the flows of these input/output materials for a particular set of smelters studied in some countries. They include Chile (Altonorte, Caletones, Chagres, Chuquicamata, LasVentanas and Potrerillos), Japan(Naoshima, Onahama, Saganoseki,Tamano and Toyo), the United States(Garfield — Fig. 1 — Miami and Hayden) and Europe (Glogow I, Glogow II, Huelva, Norddeutscheand Ronnskar).

Jan 1, 2005

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By C. C. Harris, A. Jowett, S. K. Ghosh

An equation derived from first-order kinetics and accounting for return from froth to pulp has correlated continuous flotation data. The concentration of floatable material in the pulp can be altered either by changing the feed concentration or the feed rate. The latter does not affect the flotation rate constant, the froth to pulp return constant, and the concentration of non-floatable material in both the pulp and concentrate. Both the return constant and the concentration of non-floatable material in the pulp are directly proportional to the feed concentration, while the concentration of non-floatable material in the concentrate is related to the feed concentration. The investigation of the froth flotation process by continuous test methods, previously used by Brown and smith,1 Jowett and Safvi2 and Jowett and West,3 is being continued. Recent tests, primarily concerned with flotation cell design, have yielded kinetic data suitable for testing an equation proposed by Arbiter and Harris4 which postulates that a flotation process is defined by two rate constants: 1) the rate constant for mass transfer from pulp to froth. Previous workers have regarded this as the flotation rate constant. 2) the rate constant for mass transfer from froth to pulp, which has previously been ignored. THEORY Under continuous flow conditions at the steady state in Fig. 1 the equation developed4 is Symbols are defined in Table I. The air-liquid ratio terms4 have been omitted, since they are substantially constant for a given set of conditions. Also, for a system operating at the steady state Vf and V, remain constant and Eq. 1 can be written: Cp/Cc=b'/a,+Qc/a' [2]

Jan 1, 1963

By G. Donald Emigh

WESTERN phosphate resources which lie in Ida- ho, Montana, Utah, and Wyoming, have seen great expansion of activity in recent years. Growth has been two-pronged: expansion in fertilizer use, and since 1949, into the elemental phosphorous industry. Elemental phosphorous, produced in the electric furnace, goes largely into chemical making. Phosphate ore was first recognized in the West about 1889. Production started in 1906, and for many years consisted of underground operations by small companies operating sporadically. In 1920 Anaconda Copper Mining Co. opened the underground Conda mine near Soda Springs in southeastern Idaho, and has maintained and increased its operations since then. About 1930 Montana Phosphate Products Co. began underground mining in Montana and has remained a steady producer. In 1945 San Francisco Chemical Co., one of the oldest companies in the western field, initiated strip mining at the Waterloo mine near Montpelier, Idaho, and later at Leefe mine near Sage Junction, Wyo. In1946 J. R. Simplot Co. began open pit mining at Gay mine near Fort Hall, Idaho. In 1950 Victor Chemical Works began underground development work in the area of Maiden Rock, south of Butte, Mont.: and has since mined there. Monsanto Chemical Co. began open pit mining near Soda Springs, Idaho, in 1951.

Jan 11, 1954

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By Peter Bigwood

Whether drilling through tough clay or breaking rock, or facing the most severe conditions including mixed face ground, perched water and running and flowing sands, working under-ground certainly comes with no shortage of challenges. In an environment where the unknown is faced on a daily basis, tunneling contractors must be able to rely on their equipment to get the job done properly. Not only that, their equipment must comply with two of the highest priorities: safety and efficiency. In addition to being the number one concern, a proven safety record provides additional benefits to a company. A safe work environment serves as a key component to company growth, including the ability to remain competitive in bidding and maintaining higher-level, more challenging projects.

Jan 1, 2012