Search Documents

By M. R. Dion, K. Frenette, R. K. Jonas, S. Simard, F. Robichaud

"In 2011, a site study indicated that the application of Honeywell’s Multivariable Predictive Control Technology (MPC) to the Goldex processing facility would provide significant opportunities for improvement. Grinding MPC was implemented in the SAG Mill in June 2015. This pilot application, called Phase 1, featured one of the first Multivariable Predictive Controllers to be installed in a Canadian mineral processing plant. Since the implementation of MPC, gold recovery from the gravity circuit has increased. MPC contributed to a decrease in flotation feed particle size (120 to 112 µm) and an increase in the SAG feed tonnage (8.5% increase). MPC also increased and stabilized the % solids of the SAG feed, which can have an impact on cost reduction (mechanical maintenance). Additionally, MPC increased productivity, providing grinding operators with more time to perform other tasks. Further anticipated benefits include the standardization of the grinding circuit operation from one team to the next, thereby minimizing circuit disturbances resulting from different operating philosophies. This paper will discuss the advanced control project development and justification, the technology and rapid implementation process, the performance results and the benefits obtained.IntroductionGoldex is an underground mine located near Val-d’Or that is owned and operated by Agnico Eagle Mines Limited (AEM). Between 2008 and 2011, mining focused on the Goldex Extension Zone (GEZ). In 2011, the project was halted due to geotechnical problems; operations ceased until late 2013. Goldex operations resumed in September 2013 with the M and E zones, for which there were 0.7M gold ounces of proven and probable reserves, 2.1M ounces of measured and indicated resources and 1.2M ounces of inferred resources, totalizing 4M ounces. Life expectancy was extended until 2024."

Jan 1, 2017

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By Marco Muñoz

La mina Porvenir, perteneciente al Grupo Milpo, está ubicada en Cerro de Pasco, destacándose por la corporación de equipos de alta tecnología minera adecuada a sus operaciones. En ese sentido, el presente texto señala el sistema de gestión operativa aplicado en la mina Porvenir con el objetivo de apoyar las operaciones, ya que la tecnología de información permite manejar complejidad y mejorar la calidad de las decisiones.

Jul 17, 2000

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By R. F. Shurtz

The problem of estimating the precision of systematic samples from a mineral deposit is attacked by interpolating the quality, or other attribute measured, by using Fourier approximation. Such approximation using trigonometric functions yields a particularly simple expression for the variance of the mean value of the attribute sampled. The increasing volume of publication in which the science of statistics has been applied to the problem of predicting the quality of an ore deposit from sets of samples taken from it might lead one to believe that engineering judgment can be replaced by statistics. There is, in fact, an implicit application of the principle of indifference or of "no advance knowledge" which has been discredited in modern statistical theory and practice. These pages will show that it is not always advantageous, efficient, or safe to apply this principle. This problem will be dealt with by using series of orthonormal functions to describe the distribution of the quality of ore in space as contrasted with the more commonly used distribution of quality as a frequency function. Mining engineers are rarely well acquainted with the use of such series or of the functions comprising them. These uses are commonplace in the fields of communication and information theory and it is not surprising that applications taken from these fields should be found appropriate for the analysis of the information contained in a set of samples from an ore deposit. It is hoped that presentation of the following basic, but incomplete, results will generate wider interest in this method and a fuller development of it as well as of the necessary computational techniques. FUNDAMENTAL PREMISES Random variables in the strictest sense are not very common in mine sampling. The sets of samples are almost always taken systematically and are, hence, not subject to all the laws governing random events. Therefore, unless there is indeed random experimental error in the determinations of quality, the treatment of systematic samples of n members as though they were random samples of n members often leads to calculation of confidence limits for the mean quality which are larger than they should be with the result that unnecessary additional sampling is done. The reason for this will emerge in the following discussion leading to Eq. 24 and its generalization. In order to inquire into such questions on a rigorous basis and at the same time avoid arithmetic complications that would obscure the concepts involved, a one dimensional distribution of quality will be assumed. The quality, Q, in suitable units is expressed as a function of the distance, x, along some straight traverse of the deposit. Such a function

Jan 1, 1967

By M. E. Poad, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mimes monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s Lucky Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 1992

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

By F. Lowell Lawrance

JOHN SMITH, citizen of the U.S.A., has become so accustomed to reading that Congress has appropriated billions of dollars to pay war costs. that he no longer is impressed by relatively small figures, such as several hundred thousand or a few million, in connection with Government departments.

Jan 1, 1944

By William R. Bond, Jim V. Rouse

Introduction The pressure/vacuum (p/v) lysimeter or soil water sampler has become useful for monitoring vadose zone or unsaturated zone water conditions. The soil water sampler was first introduced around 1961. It was used as a monitoring and research device for studies in agriculture and soil contamination around landfills. Since then, it has been used for many purposes. The use of p/v lysimeters at mining facilities to monitor for solution loss is a relatively new idea. The primary purpose of the lysimeter here is to function as an early warning system. It detects leakage through liners of tailings ponds, heap leach pads, and leachate holding ponds. Their use has proven valuable for collecting baseline data and detecting loss of precious leachate fluid. Different lysimeter designs are capable of vadose moisture sampling from near the surface and down to 90 m (300 ft). They are also capable of sampling soil moisture or saturation plume contaminants from areas not accessible by conventional water well installations. The most common installations are usually simple and cost-effective. In many cases, they can be installed without the use of heavy drilling equipment. A properly placed and installed lysimeter can detect solution leaks in several days or weeks. A conventional perimeter monitor well may take months or years to detect a leak of the same magnitude. A discussion on the general design and installation of p/v lysimeters will give an understanding of its versatility. Three case studies of lysimeter installations at mining sites will be examined in detail. Design, Installation, and Sampling Design The basic design of a p/v lysimeter chamber consists of a porous material through which the soil is drawn into a collection chamber. Access tubes run from the unit to the sample station at the ground surface. Most units currently available range from 25 to 76 mm-diam (1 to 3 in.-diam). The sample collection chamber, or body, can vary from 0.6 to 1.8 m (2 to 6 ft) in length. The body can be constructed of PVC casing or Teflon, depending on the installation desired. The collection chamber functions as a holding reservoir for the collected soil moisture. The intake, or porous material, on the lysimeter is the most complex and vulnerable portion of the unit. The pore size selection varies based on the needs of the installation, type of fluid to be sampled, and type of soil material surrounding the unit. Teflon (PTFE) and porous ceramic are used in fabrication of the porous inlet portion. When using a Teflon material, which is hydrophobic, a larger pore size of 70 µm is needed to overcome surface tension and draw water into the collection chamber. It is typically used at sites involving organic contamination, because of its inert properties. Ceramic material is generally hydrophilic, having less surface tension. Therefore, it has a smaller porosity range to conduct the moisture through the porous medium while under vacuum. Pore sizes may be selected from 0.16 to 6 µm, and can be manufactured for the specific needs of the installation. The final major design component of the p/v lysimeter is the access or sampling tubes. The tubes are usually of 6.3-mm-outside-diam. (0.25-in.-outside-diam). They are made of rigid polyethylene or flexible Tygon with a wall thickness of 1.5 mm (0.06 in.). The con-

Jan 4, 1985

By Paykan Safe

?? Background ?? WorleyParsons Gas Cleaning ?? PT Inco Smelter ?? Process Design Considerations ?? Furnace Control and Combustion ?? Combustion Chamber ?? Spray Chamber ?? Draft Control ?? Baghouse ?? Secondary Ventilation ?? ID Fan ?? Dust Handling Equipment ?? Project Execution ?? Heat Recovery ?? Conclusion ?? WorleyParsons Gas Cleaning ? Irving, TX ?? Formerly Gas Cleaning Technologies ?? Acquired by WorleyParsons in 2005 and now part of a global EPCM company ?? 14 years experience in off-gas system design for ferrous and non-ferrous facilities worldwide

May 1, 2008

By W. J. Theron

The purpose of the paper is to give an introduction to the concept of fatigue and its causes in the mining industry. By knowing the fundamental role it plays, together with its dynamics, can positively contribute to a mine?s safety management system. The difference between physical and psychological fatigue will be addressed with a possible range of causes that could trigger fatigue. There are two main sources of fatigue: firstly, work-related fatigue which is associated with activities at the workplace; and secondly non-work-related fatigue. The shared responsibility between the employer and employee is also discussed as it involves factors that occur both in and outside the workplace. Employers have the responsibility to manage fatigue through using a risk management approach. Employees have the responsibility to ensure they get enough sleep, take sufficient and regular nutrition, are healthy and physically fit and come to work fresh and alert. The impact of the implementation of a fatigue management plan and procedures has the potential to eliminate employee fatigue or its causes, reduce the likelihood of fatigue occurring in the workplace, and counteract the effects of fatigue when it occurs. Factors considered when implementing a fatigue management system include: extended hours of work, shift work, time of day and work design. Fatigue is one of the major role players (either causal or contributory) when it comes to causes of fatalities in the mining industry. Our main challenge in identifying whether fatigue played a role is the fact that it cannot be tested in post-mortems like drug or alcohol abuse. It is an aspect worth understanding and getting an organization sensitive to managing it properly to benefit both organizational as well as employee needs. Keywords Signs of fatigue: Causes of fatigue, circadian rhythms, the fatigue equation, fatigue management, fatigue affecting safety, fatigue fighting tips, lifestyle suggestions.

Jan 1, 2011

By Arthur R. Still, Paul Gilmour

The ore deposit of the Iron King mine occurs in a group of steeply-dipping metamorphosed eugeosynclinal volcanic and sedimentary rocks of Precambrian age. Within this sequence, the ore deposit lies at the contact of a unit made up of rhyolitic tuff and interbedded andesite and a structurally underlying series consisting of andesitic tuffs, minor rhyolitic tuffs, and argillaceous sediments. Field evidence suggests that these rocks have been overturned. The ore deposit is made up of a series of overlapping, conformable or bodies consisting of massive pyrite and associated lenses of massive quartz. These contain recoverable amounts of gold, silver, lead, zinc, and copper. A parallel zone of copper mineralization occurs within the hanging-wall rocks. The deposit is considered to belong to a large and important group characterized by mineralogical composition and the lithology and structural type of the host rocks. Evidence regarding the origin of the deposit is reviewed, and it is concluded that the ore bodies were formed through the agency of volcanic hot springs on, or near, a submarine surface of deposition

Jan 1, 1968

By R. D. Stewart

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 18pp., 5 refs. A seismic risk assessment method has been developed for application to rockburst prone deep-level mining sites which have sufficient seismic coverage. The technique utilises several seismic hazard parameters simultaneously and assesses the seismic risk on a daily basis according to the individual levels of these parameters. Critical levels are determined from investigation of the long-term behaviour of the parameters in relation to recorded potentially damaging seismic events. The method has been applied to a data set comprising 15 months' worth of seismic data, with encouraging results

Aug 1, 1995

By A T. Job, P R. McAree

There is significant value at stake in the mining industry from the implementation of new technologies that support the enhanced profitability and sustainability of mines. However, in order to realise this value, new technology must be implemented in a way that is both effective and sustainable. The industry has a mixed history for technology implementation that provides fertile ground for understanding what is necessary for innovation to deliver value. This paper describes early stage research investigating why this is so, with the aim of improving how to deliver value. Several case studies are provided covering both successful and unsuccessful technology interventions. The paper identifies the common factors that emerge from the case studies, and offers a path forward for further research in this area.CITATION:Job, A T and McAree, P R, 2017. Three case studies on the implementation of new technology in the mining industry, in Proceedings Iron Ore 2017, pp 407–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, Mexico, 150 km (95 miles) southwest of Ciudad Juarez (Fig.1). The ore deposit was discovered in 1979 and was placed in production in 1992. The production rate is about 2.4 kt/d (2650 stpd) from an ore reserve of 8.5 Mt (9.3 million st). Grades currently average about 8% zinc, 0.5% lead, 0.2% copper and 50 g/t (1.46 oz/st) silver. Substantial inflows of water into the underground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark is a joint venture with 90% participation by Minas Penoles, SA de CR of Mexico City and 10% participation by Promociones Industriales Banamex, S A de C V (PIB S A) of Mexico City. Anew company, Minera Bismark, SA de CV was formed to operate the property. Cyprus Minerals was a 40% participant in the joint venture but, in early 1993, sold its share to Minas Penoles. The Bismark Mine is one of the largest new underground mining projects built in Mexico during the last 10 years. It is the country's fifth largest underground metal mine and provides about 1 % of the world's zinc supply at about 50 t/a (55,000 stpy). Bismark is a trackless operation with overall productivities of 7.6 t/manshift (8.4 st/manshift). The 2.4-kt/d (2650-stpd) concentrator started up in March 1992.

Jan 1, 1994

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By Pound J. R

THIS mine, which is the property of the S. and M. Syndicate, London, is located at Moina, in North-West Tasmania, 18 miles from Stavertorr railway station and 36 miles from Devonport. There are metalled roads from both of these places, and, althoughhilly, these are good for team or motor traffic. Mails and passengers are provided for by a tri-weekly coach service from Sheffield, a railway town, distant 23 miles. The Moina mining field is situated on a main spur between the Forth and Iris Rivers, andat an elevation ranging from about 500 ft. above sea-level at the Forth River to 2400 ft. at the All Nations mine. The elevation at the mine office of the S. and M. mine is 1900 ft. The average annual rainfall, as recorded for the past eight years, is. 68 in.This inclildes, however, a couple of years during which the rainfall was much above normal, and taken over a longer period 60 in. would be nearer the average.

Jan 1, 1919

By F. J. Sotillo

The reduction in energy consumption has been always important for beneficiation plants. Also gravity separation processes have gained lately great importance due to environmental concerns, especially in the gold and silver Industries. In this sense, the paper point out how to reduce the energy consumption in grinding, and increase efficiency in both grinding and gravity separation are of utmost importance to optimize the use of the country’s resources. For these purposes, chemical additives, such as rheology modifiers have shown great potential, and deserved careful consideration.

Sep 9, 2007

By Chad W. Brown

"A study of five commercially available solvent-extraction diluents in combination with three commercially available extractants under sub-Saharan African copper solvent-extraction conditions yielded intriguing results. A variety of physical and chemical property analyses showed that the diluents have some property differences, but overall the properties are similar and provide comparable solvent-extraction performance. Although each physical chemical property technique provides useful information, no individual test result suffices for prediction of diluent performance. Furthermore, a diluent should be evaluated within the conditions for which it is targeted to determine a true measure of performance. Overall, the diluents studied possess appropriate physicochemical properties for sub-Sahara Africa copper solvent-extraction conditions and can be utilized to achieve efficient, safe and reliable operations. INTRODUCTION Background Today, commercial SX diluents are available globally from a limited number of manufacturers. Production quality and consistency of these diluents have improved tremendously over the past 20 years. For example, diluent flash points have been increased incrementally to improve transport and handling while reducing fire hazards. In addition, properties have been successfully modified to minimize evaporative losses, ultimately reducing SX plant raw material costs. Diluent manufacturers have also focused on meeting performance requirements of SX plants, including eliminating components detrimental to SX operations, such as olefinic groups that can react with various species resulting in changing phase-disengagement properties over time, as well as ensuring that proper hydrocarbon components are present within diluent mixtures to maintain good reagent–metal complex solubility. These challenges have been met in the midst of ever-increasing stringent environmental regulations. Sub-Saharan Africa copper SX operations pose a unique set of conditions for diluents due to inherent ore compositions and the associated high reagent concentrations required for complete copper extraction. Chevron Phillips Chemical Company, LP has been manufacturing hydrocarbons and hydrocarbon-based diluents since the mid-80s, applying this experience to identify the physical properties considered crucial for proper performance in SX operations. This paper documents the findings of a study utilizing commercially available diluents in combination with extraction reagents commonly utilized in African SX operations to evaluate the relative performance of the diluents under sub-Saharan Africa copper SX conditions."

Jan 1, 2015