Search Documents

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

The Effect of High Power Nanosecond Electromagnetic Pulses on Selectivity of Pyrite from Arsenopyrite

Sep 13, 2010

Ultrasonic Extinction for High Resolution Particle Size and Concentration Analysis

Sep 13, 2010

By A. B. Hazar-Yoruç

Ferrochromium produced by smelting chromite ores is an important alloying component in the steel industry. Ore, coke and fluxes are mixed and reacted in an arc furnace for a smelting process of ferrochromium. In ad-dition to this process, pre-reduction of chromite ore with carbon is an important industrial process. In all these processes, the mechanism and kinetics of reduction of chromite with carbon play an important role. In this study, the reduction of Turkish chromite ore with carbon was investigated. Chromite and carbon were ground to three different particle size groups. Chromite was mixed with carbon in stoichiometric and excess ratios. The samples were reduced under argon atmosphere at temperatures between 1,200° and 1,350°C. The formed phases and alloy compositions of reduced chromite samples were analyzed by optical microscopy, scanning electron microscope (SEM) with EDAX and X-ray diffraction analysis (XRD). Experimental results showed that the degree of reduction and the reduction rate increased with increasing temperature and decreasing particle size. The highest degree of reduction, 61.4%, was obtained at 1,350°C. The reduction took place in three stages: Stage 1: transformation of Fe3+ to Fe2+ and formation of metallic nuclei, Stage 2: formation of metallic crust around the particles and Stage 3: growth of the metallic crust and coalescence of the metallic phase.

Jan 1, 2007

By David V. Lewin

Heavy structures in central Cleveland, Ohio, are supported on raft foundations, driven piles, or caissons. Settlements can be predicted and structures are designed to accommodate such settlements. On one project the settlements were not provided for in the design of the structure. Soils are sands, silts, and varved clays to shale. A rift in a central area is 600 feet deep. Solutions to problems, and results, are detailed.

Jan 1, 1985

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By J. T. Nel

Non-transfer-arc linear plasma systems are highly suited to manufacturing nanoparticles. In this paper, the manufacturing of such particles with specially designed plasma systems is discussed. In general, it entails the volatilization of a metal halide that is injected in the high-temperature region of a plasma flame, where it is reacted with a suitable reagent, for example O2, to produce nanooxide powders. Metal powders can also be introduced directly in the plasma. Due to the very short residence time of only milliseconds in the reaction zone, as well as the fact that the reaction takes place in the gas phase, combined with very rapid quenching in the order of 10 000°C.s-1, nanoparticles are produced. At Necsa the manufacturing of such particles has been demonstrated on various scales. A pilot plant for the production of nano-Al2O3, and two pilot plants, one using SiCl4 and the other one using SiF4 as feed material, were built to produce fumed, pyrogenic, nano-SiO2. The alumina plant had a production rate of 8?10 kg.h-1 and the silica plants had production rates of 2 and 10 kg.h-1 respectively. Perfectly spherical alumina particles with a particle size distribution of between 10 and 200 nm were produced on a continuous system. Particle size analysis for the silica by SEM measurements showed a d50 of 60 nm and a particle size distribution of 30?100 nm. The specific surface area was in the range of 170m2.g-1. Other samples of plasma produced nanoparticles such ZnO and B4C will also be presented.

Jan 1, 2010

By Galen H. Clevenger, MARTINUS H. CARON

Although there are exceptions, oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. When these ores are of high enough grade they can be smelted; indeed, some rather low-grade ores of this type have been smelted at a profit because of their fluxing value. In the past, when these ores could not be smelted, they either were not treated or were treated at low efficiency, generally by cyanidation. The need for thorough investigation of the problem was therefore evident for some time before the writers began their research. The problem of treating manganese-silver ores seems to have been recognized first about 35 years ago by C. W. Goodale in applying pan amalgamation at Tombstone, Ariz. He attributed the low extraction of silver to the fouling of the mercury by manganese rather than to the presence of a refractory compound of manganese and·silver. Although definite knowledge as to the cause of the poor extraction of silver was lacking, a more or less effective preliminary treatment, that is, a chloridizing roast, was applied. E. M. Hamilton, in 1909, was perhaps the first to define clearly the problem as it affects the cyanidation of silver ores and to suggest possible methods of preliminary treatment. Most of the work done in the interval between the appearance of Hamilton's paper and the assumption of the investigation by the authors was in the nature of routine tests covering suggestions already made rather than of research directed to a fundamental study of the problem. No practical application has so far been made of any of these proposed processes. The investigation described in this bulletin has proved that there s a refractory compound of manganese and silver-probably a manganite- insoluble in cyanide solution and other common solvents for silver. Although this compound has not been isolated from natural ores, it has been made synthetically, and shows all the characteristics of the natural product. Furthermore the authors have shown definitely that heating in air a relatively small amount of a silver compound with a large excess of silica (in the proportions ordinarily occurring in a commercial silver ore) renders

Jan 1, 1925

By Fathi Habashi

"Crushing and grinding of ores and their beneficiation by washing away gangue minerals has been practiced since ancient times. Primitive crushing was done by hand pounding the ore with a hard stone then by using metallic hammers. The mortar and pestle was mechanized using a lever and when the size of operations increased in the middle ages, the stamp mill was introduced. The grindstone played an important role in grinding of ores. Panning for gold and hand sorting of minerals were two old methods of separation, now gave way to modern techniques. Flotation started in the middle of the nineteenth century by using oils to collect the mineral particles and float them on the surface of the aqueous slurry. It was only in the 1920s when it was discovered that organic compounds were affective floating agents. Textbooks written by distinguished engineers such as Rittinger, Rickard, Pryor, Taggart, Richards, Gaudin, and others contributed to the recognition of this field as a new discipline to be taught in Universities. INTRODUCTIONThe ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result all efforts were made to enrich the gold by washing away the light gangue minerals (Figure 1). Another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. The present day Georgia was known in ancient times as Colchis and was a center for gold working. It was known to the ancient Greek as the land of Golden Fleece. The use of special cloth to catch gold particles was also described by Agricola in his 1555 book De Re Metallica (Figure 2)."

Jan 1, 2009

By R. G. Gürtunca, J. A. Breslin

This paper briefly describes the progress in mine safety in the United States, with emphasis on recent events that have followed since the explosion at the Sago Mine in January 2006. Legislation following the mine accidents last year and areas of work carried out by the National Institute for Occupational Safety and Health (NIOSH) related to the accidents are discussed. American coal production in 2006 was 1,150 million short tons. Most of this coal is consumed domestically, with annual exports of coal about 50 million tons. One third of annual production is produced at surface mines and the rest from underground. This coal is produced by about 82,000 miners working at 1,400 coal mines. Major improvements in coal mine safety have been made in the US since the Federal Mine Safety and Health Act of 1977. The fatal injury rate in underground coal mines between 1977 and 2004 was reduced by 47.8% to 0.036. The annual number of fatalities dropped from 112 to 14 during that period. Likewise, the non-fatal days-lost injury rate was reduced by 42.6% from 10.87 to 6.24. The improvements in mine safety during this period can be seen in the graph of underground coal mine explosion fatalities and injuries from 1980 to present, which is shown in Figure 1. Between 1984 and 1993 (9 year period) there were 5 explosions and one major mine fire, for a total of 55 fatalities. Over the seven year period from 1993 to 1999 there were no fatalities from coal mine fires and explosions. However, in the six years since 2000 there have been 5 explosions and one fire, which have caused 37 fatalities. [ ]

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100 per cent recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after 12 years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

ABSTRACTMechanised cut and fill stoping in the Racecourse orebodies between II and 9 levels was started in 1964.Five stopes are in progress over the two level interval, extracting the full strike length (600-2,000 ft) of each orebody without transverse pillars.Each stope is served by a central 10 ft by 12 ft service intake ventilation raise and an 8 ft by 8 ft return air raise at each end of the stope. Each stope is divided into two sections for drilling. firing. mucking, and fillingto maintain steady production. All equipment is kept in the stope for one level lift stoping. Gardner-Denver 2 boom jumbos are used for uphole drilling and Wagner ST 5 Scooptrams for loading and transport to ore passes located in the footwall of the orebody. A Wagner PTIO is used for materials handling and scaling of the stope backs.Mill tailings, after one stage of cycloning are used to fill the stope, one section at a time. About 80 per cent of the water is removed by decantation while the remainder percolates through hessian-covered pipes and boxes.The ore is passed to 11 level where it is hauled by the 3 ft 6 in. gauge train to the tipple at the shaft area. The ore is crushed underground before hoisting to the surface.A performance of about 100 ton/manshift is achieved by the drilling, blasting, and mucking crews in the stopes.

Jan 1, 1968

Variations in delay timing can have a marked influence on blasting effectiveness and, hence, on total production costs. In single-row bench blasts, delay firing is invariably more effective than simultaneous initiation. In single-row delayed blasts, there is an optimum inter-hole delay above and below which inferior blasting results are obtained. This optimum delay is equal to the time required for each charge to just effectively detach its quota of the burden. The inter-hole delay should seldom be less than 4 ms.m-l of burden.In multi-row blasts in which holes in a given effective row are fired on the same delay, the entire burden on any effective row should be detached from the rock mass just before charges in the next effeotive row detonate. Delays shorter than this give inferior blasting results and an increased likelihood of environmental and slope stability problems. If the inter-row delay is too long, cut-offs can occur, especially where the delay unit is located outside the blasthole. For a surface delay system, the optimum inter-row delay usually varies between 4 ms.m-l and 8 ms.m-l of effective burden. The number of rows that can be fired effectively with surface delay systems (in a single blast) is limited by the threat of cut-offs. Greater interrow delays and a larger number of rows per blast can be fired to advantage with down-the-hole delay systems.There are practical limits to the timing accuracy of all available delay systems. The existence of delay time variability should be recognized and duly considered in the design of blasts.The relationship between delay timing and blasting vibrations is not discussed.

Jan 1, 1977

By H. C. Fuller, E. L. Anderson, F. S. Wartman, M. A. Cook

"This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic chloride with magnesium, followed by grinding, leaching, and magnetic separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described, and some data on operating costs are given.Although man has been aware of the existence of the element titanium for over 150 years, only recently has the metal itself been available in a form pure enough, particularly with reference to absorbed gases, to allow an estimate of its physical properties. In comparison with mild steel, the tensile strength of titanium is about the same, the resistance to atmospheric corrosion greater, and the specific gravity much less.These properties suggest the usefulness of titanium as a structural material for applications requiring resistance to atmospheric attack and a good strength-weight ratio. Although known reserves of titanium, high-grade enough to be useful at present are not sufficiently extensive to predicate that titanium might supplant iron, aluminum, and magnesium for structural purposes, the reserves are large enough to make its use as a structural material quite feasible in certain fields in which its unique properties are required.As a result of these considerations, the Bureau of Mines station at Tucson initiated an, investigation into the technology of titanium in 1938. First, a critical survey and small-scale trial of virtually all suggested methods7/ for producing the metal was made. The method devised by Kroll8/ seemed best adapted as a source of metallic titanium for, although the purity of the product was not as high as that of products from some other processes, it seemed that modifications in technique necessary for larger-scale production could be made more easily.Essentially, in applying the Kroll process, titanium tetrachloride was reduced to metallic titanium by adding the chloride slowly to molten magnesium contained in a molybdenum-lined iron reaction chamber filled with a protective atmosphere of argon. After reduction to the state of completion desired, the reduction mass and chamber were allowed to cool. Then the chamber was opened, and the reaction mass, consisting of titanium, magnesium chloride, and some unused magnesium, was removed by suitable means. Most of the magnesium chloride and metallic magnesium were removed by leaching in dilute hydrochloric acid. The leached sponge was then ground wet in a ball mill, releached in strong acid, and dried Removal of free iron by magnetic separation completed the production process.Development of the Kroll process by the Bureau was undertaken first at the station at Salt Lake City, in 1942 and the amount formed per run was increased in several steps from a few grams to pounds.9/ In addition to increasing the size of batch over that used by Kroll, the technique was simplified somewhat by the use of unlined reaction vessels."

Aug 1, 1949

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By J. W. Meier

Introduction The great importance of air warfare during World War II and the introduction of large-scale air transportation and airborne operations created an immediate demand for large quantities of high quality light alloy products. Before this war, the use of magnesium, the lightest structural metal, was barely in the development stage, and considerable research work was needed to overcome difficulties in improving its properties and to attain uniform quality in mass production of magnesium alloy products. The Canadian Bureau of Mines was frequently called upon, by various agencies of the Armed Forces and of the newly established war industries, to examine magnesium alloys that had failed in fabrication or in actual service, and to advise on proper alloys and fabrication methods to be used. Failures in magnesium alloy castings were connected mainly with lack of knowledge of proper founding and surface-protecting techniques. Most of the defects were due to microporosity and faulty heat treatment. To aid the foundry industry, small-scale investigations were started on the effect of various factors in the casting technique in order to improve the quality of the products. These investigations were made in co-operation with representatives of the Armed Forces and the Canadian magnesium industry. This work was later co-ordinated into a broad research programme on magnesium alloys, comprising problems on melting, refining, various casting methods, heat treatment, and testing of properties of standard and special alloys. This research programme? is still in force, and the present paper contains some results of the first series of investigations on magnesium casting alloys carried out at the Experimental Foundry of the Bureau of Mines.

Jan 1, 1948

By L. E. Eary

Many of the major international gold mining companies provide data on rates of greenhouse gas (GHG) emissions as part of their environmental reporting commitments. These data are evaluated by an index defined as the annual GHG emission rate in metric tons, divided by the annual amount of gold produced in grams, and referred to as GHGgold. This paper examines ranges of GHGgold values for a cross section of gold mines as a function of mining method (openpit, underground and combined operation) and ore-processing method (mill, heap leach and combined methods) for reported ranges of operational data, including annual total tons mined, ore processed and gold grade. The evaluation shows that ranges and distributions of rates of GHG emission are approximately similar across different mining methods and ore-processing methods. The data presented in this paper provide the context needed to make comparisons of GHG emissions reported in companies’ annual reports to the ranges reported for the overall gold mining industry.

Jan 1, 2009

By Christian Neumann, Josef Arnold, Albin Reinhart

The Channel Tunnel Rail Link (CTRL) is the most significant railway infrastructure development project in the United Kingdom since the construction of the Channel Tunnel between France and England. The key element of this project is the 2-mile-long(3.2-km) North Downs Tunnel, which will be the largest and deepest twin-track railway tunnel ever constructed in the United Kingdom. This paper describes the contractual agreement, the design and construction (excavation and lining) of a twin-track rail tunnel with a 166-m 2 face excavated through chalk using the New Austrian Tunnelling Method (NATM). The importance of collaborating with a tunnel contractor/designer who not only is expert in the New Austrian Tunnelling Method, but who was also responsible for the design and installation of the primary lining, will be highlighted in this paper. This paper will also deal with the benefits of partnering in tunnel design and construction, as well as the resultant added values of mechanizing conventional tunnelling methods (Value Engineering).

Jan 1, 2001