Search Documents

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By María Cristina Ruiz

Enargite rich copper concentrates can not be treated by conventional smelting/converting technology and thus nonconventional methods such as leaching must be used. Since enargite (Cu3AsS4) is a hard to dissolve mineral in acidic solutions, pyrite, a common impurity in copper concentrates, could be used to increase the enargite dissolution rate. On this matter, we present in this work experimental data on the pressure leaching of a mixed enargite-pyrite concentrate in H2SO4-O2. The results show that the dissolution of enargite from the mixed concentrate is considerably faster than the dissolution of pure enargite mineral. The leaching rate increases significantly with temperature. Over 98% of enargite was dissolved in leaching 64 micron size particles at 200 ºC and 100 psi of partial pressure of oxygen in just 30 minutes. A change in the partial pressure of oxygen from 50 to 150 psi showed also a large influence in the leaching rate.

Jan 1, 2010

By Taegong Ryu

Nanosized tungsten powder was synthesized by the hydrogen reduction of ammonium paratungstate (APT) in thermal plasma. The effects of operating conditions on the product composition and particle size were investigated. The particle size of synthesized W powder was less than 30 nm in all cases tested. The sintering behavior of the synthesized powder (25 nm average size) was then investigated and compared with those of commercial W powder of 500 nm average size and W powder of 23 nm average size produced by milling the commercial powder. The sintering was done at 1400oC with various holding times. The hardness of the resulting compact from the synthesized W powder (315 VHN) was similar to that from the milled W powder (309 VHN), but the plasma-synthesized powder had a much lower tendency to form cracks. The compacts of both nanopowders were significantly harder than that of the commercial powder (192 VHN).

Jan 1, 2009

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By Cem Colakoglu

In this study, nickel containing iron alloys were produced by carbothermal reduction of lateritic nickel ores obtained from Manisa - Caldag region of Turkiye in order to investigate the reaction mechanism of nickel and cobalt. In the experiments, the lateritic ore containing 1.58 wt.% Ni and 0.12 wt.% Co was calcined in a semi-pilot scale rotary furnace at 1100°C for 1 hour. Then, a mixture of calcined ore and metallurgical coke was reacted in sintered alumina crucibles using a graphite resistance tube furnace at different time (0- 60 min) and temperature (1500-1600°C).

Jan 1, 2009

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

By Xiao Caimei

The method of Substance Flow Analysis (SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level, such as copper, lead etc. In this paper the flows and inventory of cobalt in China, 2008, were traced with the STAF model, and the situations of production, fabrication and manufacturing, use and waste management in China were introduced. The result revealed that the resource of cobalt in China was so poor that a large amount of cobalt material or cobalt products needed to be imported, and there was lack of recycling of cobalt resources.0

Jan 1, 2010

By Y. F. Liang

Fe-6.5wt.%Si alloy has excellent soft magnetic properties compared with conventional silicon steel. It is very brittle at room temperature due to appearance of ordered phases, like B2 and DO3. In this paper, we investigate the effect of ordering on cold workability of this alloy. Methods of rapid quenching and hot rolling were utilized. It is found that rapid quenching and proper heat treatment of the hot rolled sheet could decrease the degree of order due to the very high solidification rate and high cooling rate. The rapid quenched sheet and hot rolled sheet after proper heat treatment could be cold rolled without crack. Microstructure, phase ordering, micro hardness, and cold rolling properties were investigated by Optical Microscope, X-ray Diffraction, Micro Hardness Indenter and Four-high Mill.

Jan 1, 2009

By Regina Maria Pinheiro

This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation in the amount of 10 wt.% on the properties and microstructure of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis. Incorporated bricks were produced in industrial scale before firing at 750°C in a Modified Caieira type furnace. The physical and mechanical properties evaluated were water absorption and compression strength. The microstructure of the fired ceramic was evaluated by optical microscopy. The environmental evaluation was made by solution test and atmospheric emission by monitoring the release of SO2, NOx and particulate material. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. The properties of the fired ceramic attend the norms. With respect to the environmental aspect, the incorporation of the waste did not impact the environment.

Jan 1, 2009

By R. Fragoudakis

AISI 4130 steel is a medium carbon Cr-Mo steel used in automotive, aeronautic and other general-purpose industries. In this study, 4130 steel fatigue specimens were carburized at 927oC to enhance the carbon content in the steel, raising it from approximately 0.30% (non-carburized) to 0.90% (carburized, oil quenched and tempered). Rotating bending fatigue tests were performed on the R. R. Moore Rotating Beam Fatigue Testing System, in order to determine the high cycle fatigue (HCF) life of 4130 steel and plot the corresponding S-N diagrams. A comparison of the results of carburized and non-carburized specimens shows that carburizing of steel: a) increases the surface hardness and b) improves the fatigue strength of the steel by at least two orders of magnitude.

Jan 1, 2010

By Leon H. Bruner

This paper presents a case study describing how a global consumer products company with 138,000 employees that markets over 300 brands in 180 countries is building sustainability into the rhythm of its business. This strategy extends beyond social investment programs by incorporating sustainability into the fabric of product design, manufacturing operations, employee engagement and stakeholder partnerships. During the implementation of this program it has been necessary to be explicit about sustainability and its importance to the business, to broadly define sustainability, to ensure that sustainability is not added work, to eliminate trade-offs between performance, value and sustainability and to implement programs to ensure that sustainability is incorporated into the DNA of the company. Our program continually emphasizes the importance of making no tradeoffs between consumer acceptance of sustainable products and sustainability investments. We also work diligently to overcome the challenges of engaging employees around the world to implement a single coherent sustainability strategy that delivers great results.

Jan 1, 2010

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

By Yanjie Liang

Elemental sulfur and volatilization kiln slag(VKS)containing heavy-metal produced by smelter factories were used to produce sulfured building material. The effects of heating mode, material proportion (MSulfur:MVKS), size of waste particles and ratio of aggregate to filler(A/F) on the mechanical properties and leaching toxicities of solidified stuff were investigated. The optimal conditions for the solidification are stepped heating mode, 3:7 ratio of MSulfur to MVKS, particle size less than 150µm and 3/17 ratio of A/F. Under the above optimal conditions, the compressive strength of solidified stuff rises to 35 MPa, and water absorption is down to 4%-6%.Furthermore, when NaOH is applied as an additive in the process of solidification, the 2+concentrations of most heavy metals except Pb have reached the national leaching toxicity standard. The results of X-ray diffraction reveal that sulfured solidification is caused by the physical encapsulation rather than chemical transformation.

Jan 1, 2010

By Xi Zhang

A technique for fabricating free-standing, high-aspect-ratio porous and pillar-type Ni structures has been developed using wet Si processing. A wafer of (100) Si was initially etched in HF solution to form deep pores with micron-sized diameter. The aspect ratio can exceed 200. By introducing the as-etched Si into a defined aqueous Ni2+ solution, Ni deposits grew rapidly onto the sidewalls and replaced the Si. Long-time immersion allows the Si sidewalls to be completely converted and thus form a metallic Ni structure with high-aspect-ratio pores. It is known that close-packed submicron Si pillars can be formed by oxidizing and subsequent etching of the macropore sidewalls. Treated in the same Ni solution, high-aspect-ratio Ni pillars were correspondingly emerged by replicating the original pillar-type Si structure.

Jan 1, 2006

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

By Liang Sha

In this study, adsorption of copper by chemically modified orange peel was investigated. A conspicuous change occurs in the surface morphology of the biomass due to modification, which is depicted by SEM images. Equilibrium isotherms and kinetics were obtained and the effects of various factors, including solution pH, contact time, initial metal ions concentration and temperature, were studied by batch experiments. Kinetics was found to be best-fit pseudosecond- order equations. Equilibrium was better described by Langermuir isotherms rather than Freudlich isotherms. At 25?, pH5.30, the maximum adsorption capacity was 70.67mg?g-1 . With increase of temperature, adsorption efficiency decreased. The biosorbent was suitable for repeated use for more than five cycles.

Jan 1, 2009

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By Jay S. Gunasekera

Since great emphasis is being placed on the manufacturing science and processing science programs in the Department of Defence and other government research agencies and industries; currently, extensive research on computer aided design(CAD)/ computer aided manufacturing (CAM)/ and computer aided engineering (CAE) is being conducted at Ohio University (OU) . OU has invested over a million dollars in CAD/CAM hardware and software. Design and analysis packages like ALPID, NIKE, STREAM, SHEAR, POLY_FLON, RINGROLL have been developed or modified at OUusing finite element method, finite difference techniques or enhanced slab analysis. Packages like ABAQUS, FLUENT, and NASTRAN have been extensively used.

Jan 1, 1990

By Gabrielle Gaustad

For aluminum, substitution of primary with secondary resources decreases energy consumption; this energy advantage creates a strong economic incentive to recycle. Several authors have raised concerns that the current sinks for secondary materials may soon be saturated, impeding subsequent expansion of recycling. This work combines dynamic material flow analysis with optimal batch planning models to quantify the significance and drivers of these pending limits under several scenarios, and thereby explore potential opportunities to increase recycling. An aluminum recycling system case was developed that includes containers and packaging, automotive, and construction products and scraps. The impacts on aggregate scrap utilization and materials cost are explored in the context of changing alloy demand and lifetime. Insights drawn from this specific case study could be applied to multi-stakeholder, systemic models.

Jan 1, 2010