Search Documents

By P. M. Swash

The determination of the heavy minerals in beach sand samples is highly dependent on the preparation technique used. In this paper a simple reproducible method for the quantification of "recoverable" ilmenite, zircon, rutile and leucoxene by magnetic separation, is described. The procedure recommended yields information relevant to the metallurgical processing of the ore rather than to the total heavy minerals present in the samples. Finally the determination of mineral reserve estimations and grade assessments is greatly facilitated when this "mineral assay" method is employed. An assortment of other mineralogical methods are described including SEM, EMPA, XRD, XRF, Image analysis, Mossbauer. clerici and perm roll separations. The methods are briefly examined and the practical information that can be gained by using such techniques are reviewed. Experience has shown that an understanding of the relationship between the physical and chemical properties of the heavy minerals can contribute to the prediction of mineral particle behaviour. Such information may ultimately help reduce the prospect evaluation period and minimise expenditure on metallurgical testwork.

Jan 1, 1991

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By Nathanael Hudson, Ruel A. Overfelt, Sushil H. Bhavnani

"In the aerospace and automotive industries, complex shapes exist which require casting. The problem with these cast parts is the empiricism required to develop the casting process and the accompanying time and expense to develop that process.There has been an interest in using fluidized beds to allow molding sand to better encapsulate the complicated surface geometries of lost foam patterns. Fluidization coupled with a mixing jet helps to homogenize the sand through stirring and may improve the integrity of the casting.At issue is the hydrodynamics of the sand and air around the foam pattern. The commercial package PHOENlCSTM is used to simulate the flow around the pre-casting foam geometry. Employing a two fluid approach, each component is considered a fluid that interpenetrates the other phase. To this end, the kinetic theory of granular 'flow for the sand phase was incorporated into the re-compilable PHOENlCSTM code.The results of this study consist of time-averaged void fraction patterns, with voidage being defined as the fraction of air in the mixture, around the foam pattern submerged in a two-dimensional fluidized bed. The model was benchmarked against past fluidized bed experiments. In order to better understand the dependence of the void fraction pattern around the lost foam pattern, certain physical parameters are varied and the resultant void fraction maps are predicted with the model. Physical parameters such as the aspect ratio of length to width, the placement of the mixing jet, and different mixing jet velocities are varied to illustrate the dependence of the time-averaged void fraction on those variables.Results consistently indicate the presence of channeling around the lost foam pattern, with the extent of the channeling and void formation reliant to a greater degree upon the placement of the mixing jet, and to a lesser degree on mixing jet velocity and aspect ratio.The increase in radial position of the mixing jet from the bed centerline had the desirable effect of granting the churning benefits of a penetrating jet, while at the same time minimizing the formation of excess void fraction at the top of the pattern."

Jan 1, 2001

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to smelter smelting plants. In both primary smelting and converting, gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to sulphide smelting plants. In both primary smelting and converting. gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By A. Van den Steen

In the early fifties Professor Breckpot of the Louvain University in Belgium in collaboration with the Research Laboratory of Metallurgie Hoboken, discovered the possibility to separate nickel from cobalt sulfate solutions by a nickel sulfide depolarized cementation. This reaction, completed later with a zinc precipitation, was developed into purification processes for the Shituru and Luilu Gécamines cobalt plants in Zaíre. Due to increasing demand for higher quality products and the necessity of lowering the production costs, more laboratory and pilot plant investigations concerning the key parameters for the nickel and zinc sulfides precipitation were under- taken. Especially the relative stabilities of cobalt, nickel and zinc sulfides, precipitated with elemental sulfur or sodium hydrosulfide, were examined in relatlon with the pH and with the redox potential. These investigations have led to better plant practice and new development possibilities. The valorisation of the precipitated sulfides has also been considered.

Jan 1, 1988

By R. D. Pehlke

The history and present status of continuous casting of steel are reviewed, including a genera 1 description of current processes. Plant layout, process development and elements of machine component design are outlined, and key steps in integration into a stee-1 production system are detailed. Recent productivity advances and improvements in quality are described. Process developments are reviewed, and some future avenues for this technology are considered.

Jan 1, 1985

By Gerald M. Ellis

Exploration for gold .deposits on Hispaniola has taken place sporadically over the years but has expanded in the past decade. There are veintype, disseminated, alluvial and elluvial deposits. Investigations were previously undertaken in Haiti by combined Haitian, Bureau of Mines, and UN geological teams at Grand Bois Limbe(Milot) and Cap Coq areas. Later studies were conducted at the Miches and Moncion districts. Gold occurrences were reported in quartz, silicic-barite veins and gossans. An important deposit ?at Pueblo Viejo is? a disseminated type where extraction is taking place in the oxidized zone. Exploration by Japanese and West German firms with local geologists are described in this paper together with Pueblo Viejo, Miches, Restauracion, Milot, and Meme ?areas where occurrences are known. Copper deposits with associated gold va1ues are also described. These include vein deposits in Central Cordillera and disseminated deposits at Terrier Rouge and Blondin.

Jan 1, 1989

By Gabriel A. Torma

This paper provides infonnation on selected technologies available for remediation of metal contaminated soils and industrial effluent solutions. Because some of the industrial sites are contaminated with organics (solvents, gasolines and oils), an effort has been made to introduce the most frequently used cost-effective cleanup methods, such as "bioventing" and "composting." The microorganisms involved in these processes are capable of degrading organic soil contaminants to environmentally harmless compounds: water and carbon dioxide. Heavy metals and radionuclides contaminated mining and industrial sites can be remediated by using adapted heap and dump leaching technologies, which can be chemical in nature or bio-assisted. The importance of volume reduction by physical separation is discussed. A special attention is devoted to the remediation of soils by leaching (soil washing) to remove heavy metal contaminants, such as chromium, lead, nickel and cadmium. Furthermore, the applicability of biosorption technology in the remediation of heavy metals and radionuclides contaminated industrial waste waters and acidic mining effluent solutions was indicated.

Jan 1, 1996

By M. Giralico

Optimized mixer settler designs will now handle flows of over 25,000 GPM. The size and expense of the equipment hamper experimental settler optimization efforts. Computational Fluid Dynamics (CFD) is a timely and predictable tool for settler design development. In the past, CFD has been used to evaluate only the flow field in pumped and auxiliary tanks. A similar numerical analysis is used to evaluate settler flow and phase separation. Phase separation is analyzed using multiple species for the aqueous and organic phase. Experimental validation shows good agreement between the computational and experimental solutions in both flow field and phase separation. The computational model is used to show performance differences between various choices of settler geometry, liquid depth, with variable flow rates. Understanding the differences allows the development of optimized settler designs. System improvements are predicted to lower entrainment levels further and/or allow new smaller footprint designs. This paper focuses on the major design components of the settler and how future technological advances will lead to further improvements in their design. LIGHTNIN?s new designs will handle tomorrow?s production requirements, while maximizing profits.

Jan 1, 2003

By Brian Lightfoot

Ausmelt technology is a versatile bath smelting technology with application in many waste treatment fields at low capital and operating cost. Heavy metals extracted from wastes may be recycled to mainstream use and the slags produced will be inert and suitable for use as aggregate, shotblasting grit or other applications.

Jan 1, 1994

By J. C. Agarwal

Most metals are produced from minerals containing one or more of the desired metals, some contaminating metals, silicate, oxides, carbonates, and sulfides. Therefore, in the production of metals, there is generally a gaseous effluent in pyrometallurgical processes and a liquid effluent in hydrometallurgical processes. There are also solid residues such as waste ore, tailings, dust, and slag, created by the metal recovery processes. There are two important distinctions between the effluents and the residues: I. Effluents ? gases and liquids ? affect the neighboring environment for miles from the point of emission, while residues affect only the soil on which they are stored or dumped. 2. The environmental and economic effects of effluents are known and felt essentially immediately. By contrast, the environmental effects of the residues may not be known for a long time. For these reasons, the economic impact and the potential corrective actions required are very different for effluents and residues.

Jan 1, 1992

By Alicia Esther Ares, Carlos Enrique Schvezov, Alejandra Silvina Roman, Claudia Marcela Méndez

In this paper the structure of aluminum based alloys and their corrosion behavior by using different electrochemical techniques as characterization methods are considered. Currently, it becomes imperative to know the role of the Al2Cu against the susceptibility to corrosion of these alloys. The present work aims to studying the electrochemical behavior of aluminum base alloys with the following compositions: Al-1wt.%Cu, Al-4.5wt.%Cu and Al-15wt.%Cu (with different grain structures), in 1M NaCl solutions, at room temperature. Cyclic potentiodynamic polarization tests were performed and were found that the alloys with more than 1wt.%Cu in the matrix have an unstable behavior and without tendency to reach passivity. The equivalent circuits derived from electrochemical impedance spectroscopy technique (EIS) generally showed two capacitive contributions. The susceptibility to corrosion becomes a complex function, not only of copper concentration and structure, but also with interdendritic spacings and distribution of phases in the alloys.

Jan 1, 2015

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By Aliye Arabaci

In the present investigation, an attempt has been made to study the reduction behavior of composite pellets consisting two different types of iron oxide fines (high and low grade) and coke or lignite fines as reducing agents. The reduction experiments were carried out under isothermal conditions and constant flow of nitrogen gas in the temperature range of 900 ? 1100 oC. The variables investigated are the reduction temperature, Cfix/Fe3O4 ratio, reduction time and reductant type. In the experiments carried out with Sivas Divrigi A head magnetite ores (high grade) at a temperature of 1100 oC, for 40 minutes and on the condition that Cfix/Fe3O4 ratio is 0.2, in which lignite and coke fines were used as reductant, degree of reduction was obtained as 91 % and 86 %, respectively. Whereas, in the experiments realized with Malatya-Hekimhan-Hasançelebi magnetite ores (low grade) on the same conditions by using lignite as the reductant, around 60 % degree of reduction was found.

Jan 1, 2008

By Shengli Wu, Mingyin Kou, Feng Chang, Laixin Wang, Hua Lu, Jianliang Zhang

Sintering dust has been regarded as an important secondary resource in a modern steel plant. Sintering dust was mechanically treated using different milling machines and experimental conditions in air atmosphere. The changes in phase constitution, particle size, specific surface area, particle morphology, and lattice parameters of activated sintering dust were determined. It was found that the agglomeration of the particles take place during extended dry milling with accessible pores for Nitrogen gas. The maximum specific BET surface area in the stirring wet grinding and planetary wet grinding increases to 43.06 and 46.45 m2/g after activated 360 min respectively. With the increasing of energy input, the intensity of diffraction peaks of dolomite and hematite gradually decreased. Furthermore, the previous phase almost disappeared eventually under any experimental conditions. In addition, Fourier transform infrared spectroscopy indicates that organic matter and carbonate decompose easier than other phases, especially under stirring wet milling.

Jan 1, 2016

By W. K. Tolley

The Bureau of Mines is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from CdTe scrap produced in the manufacture of infrared optic devices. Sulfation, ferric chloride leaching, and oxygen-pressure leaching have been tested. Cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. However, no satisfactory scheme for dissolution of the higher valued tellurium has been devised. Leaching the ground CdTe for 75 min at 110°C in 1.1M H2S0, under 120 psig 0, yielded 99.5% Cd extraction. Tellurium remained in the leach residue as TeO, and elemental tellurium; residual cadmium was less than 0.5%. The cadmium in the leach liquor was purified of coextracted metals such as gallium and iron by adjusting the pH. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Recovery of by product metals, notably gallium, is possible.

Jan 1, 1991

By U. M. Mutnti

In order to meet the stringent market requirements for high purity cobalt, ZCCM commissioned the VIR plant in December 1982. The plant comprises a 4.1 tonne/heat vacuum induction furnace with a rated annual capacity of 2,500 MT of barstock. In the VIR furnace, molten cobalt is held under vacuum at 1600°C resulting in the removal of more volatile impurity elements by distillation. Operations todate have demonstrated that Pb, Zn and Cd have good distillation rates in excess of 95%, leading to cobalt containing 1 ppm or less of the above elements. Removal of other impurities such as Se, Bi is about 65% with the finished product still assaying around 1 ppm of each of these elements. Vacuum refining of cobalt offers an economic route for producing higher grades of cobalt from the type of concentrates and treatment processes available within ZCCM. The consistency of VIR cobalt quality has been confirmed by ZCCM and some of its alloy customers.

Jan 1, 1988

By N. Mizutani, S. Harada, Z. Asaki, T. Tanabe

"The development of lead-free solders is urgent in view of environmental standpoints. In this -work the wettability of tin-bismuth- silver solders on copper was studied. Three kinds of fluxes were used. The wettability of conventional eutectic tin-lead .solder exhibited an excellent level over the other solders of tin-bismuth systems. Poor wettability of the tin-bismuth solders may be caused by the growth or dendritic copper-tin compounds at copper/solder interface, in contrast to the case of tin-lead'· solder. The wettability was improved by the addition· of silver in the solder. In this tin bismuth- silver system, silver was abnormally concentrated at the copper I solder interface even in the initial stage of contact. The wettability of the solder and the thickness of compound formed on the copper have a good correlation; the solder containing 2% silver exhibited the best wettability and the formation rate of copper-tin· compound on the copper was slowest.IntroductionSocial demand to avoid lead use in the industrial fields has been recently promoted· (1) because of the environmental protection of water resources. Especially the lead-bearing solders have been widely used in electronics and automobile products, and it is urgent to replace them with nontoxic materials (2)-(4). Thus the development of lead-free solders becomes an indispensable subject to the new generations and many works (5)(6) have already been carried out on the research and development of new solders. New lead-free solders are expected to have some requirements, for example, moderate melting temperature, proper strength and integrity, and lower prices, as compared with conventional solders. There have been already several alloy systems developed. Among ·these alloy systems, tin-bismuth binary or tin-bismuth-silver ternary alloys have great advantages such as having a wide range of soldering .temperature by controlling con:ipositions, though they have such disadvantages as ""lift-off"" (7)-(9): It is said, on the other hand, that a frequently overlooked property of solders, or one that is typically ignored by the research scientist as an ""issue"" for the manufacturing or product engineer, is wettability (10), although a ·work on the wettability has recently been published (11). In this Work, therefore, the authors selected Sn-Bi-Ag solders and focused mi the effect of Ag-addition to wettability of the solder."

Jan 1, 2000

By Zhongliang Tian, Yun Cheng, Yexiang Liu, Ming Jia, Yanqing Lai

"A fundamental electrochemical study of Si ions in Na3AlF6-LiF melts and electrolysis using liquid cathodes was conducted. Cyclic voltammograms (CVs) clearly showed the depolarization of silicon deposition on liquid cathode by forming chemical complexes with the liquid solvent metals. Besides, co-deposition of Al and Si is possible when Si ions are insufficient in the molten salt. Based on the electrochemical results, silicon diffusion into liquid cathode is modelled and evolution of Si activity with concentration is deduced by a mathematic approach. Electrochemical study using liquid metals as working electrodes, can be used as an alternative approach for the acquisition of basic data on alloy behavior. Galvanostatic electrolysis showed that liquid cathodes are appropriate to collect the deposited solid silicon and the highest collection efficiency is almost 85%.IntroductionRecent years have witnessed an increasing demand for solar-grade silicon (Si) by the photovoltaic industry [1-4]. The preparation of high-purity metals through electrolysis and electrorefining offer many advantages such as low cost, low-energy consumption, and environment-friendly process, and thus has been widely used worldwide. From the perspective of electrochemistry [5-7], by utilizing the electronegativity difference between the impurities and Si and controlling the relevant process parameters, it is possible in principle to electrodeposit monatomic Si from a Si4+-containing compound melt. Moreover, because the carbon content of the high-purity Si obtained through electrolysis can be effectively controlled and used as a very ideal raw material in the preparation of electronic-grade and solar-grade Si, the preparation of high-purity Si through electrolysis has received widespread attention [8,9]. Monnier et al. [9] used a graphite electrode to obtain high-purity Si (99.9 %-99.99 %) from Si02/Na3AlF6 system through electrolysis; however, because the Si was precipitated in a solid form and showed poor conductivity, the deposition rate was too slow. Olsen et al. [10] obtained high-purity Si films via electrodeposition in K2SiF6/KF-LiF system by selecting electrode materials with high surface quality (such as Ag and graphite). However, in order to ensure the film quality, the deposition current density must be relatively low (10-50 mA/cm2), resulting in a low current efficiency and low deposition rate, which are not conducive to reducing energy consumption and applying to practical use"

Jan 1, 2014