Search Documents

By A. P. Paiva

With the aim of establishing a valuable alternative to the conventional methods, studies regarding the recovery of precious metals by solvent extraction have been increasing over the past few years. In this work, the selectivity of extraction presented by Cyanex 471X toward silver is investigated. Simulated chloride solutions considering contents of iron and copper usually present in actual leaching practice were used. The characterization of the aqueous solutions - in terms of the multiple equilibria established by the chlorocomplexes of the different metals and their relation to the total chloride concentration of the base-electrolyte - was successfully carried out by cyclic voltammetry. The results obtained support the important contribution of the electrochemical techniques for the understanding of the overall extraction phenomena.

Jan 1, 1994

By Leonard Harris, Rosa H. Harris

"It is becoming increasingly obvious to mining and exploration companies, when operating overseas, that their activities should not conflict with the interests of the surrounding communities. The world's largest gold heap leach operation, Minera Yanacocha has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted with joint venture partners consisting of the company, the community people, the contractors and suppliers, government and non government organizations and a ladies association composed of the employees' wives and female staff.IntroductionThe l 990's is the decade highlighted by enormous investments in mineral exploration and mining projects in the developing world. Figure 1 illustrates the distribution of exploration spending by mining companies in 1995."

Jan 1, 1997

By Jan Steinhoff

The design options of a gravity separator are still limited and rely on the study of settling behavior. A methodology will be presented where an experimentally given inlet droplet size distribution (DSD) is the basis for the calculation of the dispersion layer in a gravity separator. A pilot-scale continuous gravity separator is presented and CFD (computational fluid dynamic) results are validated. A transmitted light measurement technique for the determination of the DSD is presented up to a holdup of 15% dispersed phase. The resulting DSD was in the range of 20–2000 μm depending on flow rate and phase ratio. Furthermore, correlations of the real DSD with the settling behavior of the dispersion in a settling cell are discussed. The new approach to the description of gravity separators will be presented and the applied CFD methods showed good results with the system water/paraffin.

By Liang Wang, Sheng-Kai An, Bing Xie, Hong-Yi Li, Cui Li

In order to develop an environment-friendly method for extracting vanadium effectively from aqueous solution containing vanadium, the dynamic adsorption behavior of V by a continuous fixed-bed column which was filled with macro-porous weak base anion exchange resin was studied. Effects of conditions including the bed depth, flow rate, concentration of vanadium ions on dynamic V adsorption were investigated. The optimum adsorption conditions were established at flow rate of 6 ml/min with bed depth of 20 cm. Isotherms studies demonstrated that the column adsorption of V was a favorable chemical ion exchange process in monolayer. Several kinetic models were applied to analyze the adsorption characteristics. Analysis results of the Bohart-Adams model indicated that the adsorption process was dominated by external mass transfer in the initial stage. The Thomas model was appropriate to describe the column behavior, revealing that both external and internal diffusions were involved in the limiting steps.

Jan 1, 2014

By Frank A. Vonesh

In order to reduce the amount of visible, airborne emissions in the Metals Industry, a new Industrial Gas Technology was developed by Air Liquide. This patented technique is called ALECT?, Air Liquide Emission Control Technology. Demonstrations have been conducted for many cutting and lancing operations as well as for hot metal transfer from vessel to vessel. Fume reductions of 90% and greater have been achieved in actual practice. Air Liquide continues to improve the process and the associated control equipment.

Jan 1, 1994

By O. P. Pandey, Rama Arora, Gurmel Singh, Suresh Kumar

The tribological behavior of Dual Particles Size (DPS) rutile reinforced LM13 alloy composite was investigated under varying applied pressure from 125 kPa to 625 kPa at a constant sliding speed of 1.6 m/s. In the present studies, 15 wt.% of rutile particles of different sizes (50-75 μm and 106-125 μm) are reinforced in the Al-12Si alloy (LM13) by liquid metallurgy route. Microhardness of the prepared samples was measured in different phases. Microstructure, wear mechanism and surface morphology of the wear surfaces and debris was observed under optical and scanning electron microscope. The change in wear behavior has been explained with reference to the observed EDS analysis of the wear track and debris. However, an interesting change in wear feature, mild to severe wear transition at critical pressure was noticed in wear behavior of the composite. The Al-DPS composite has immense potential to be used as a component material for tribological applications.

Jan 1, 2015

By Saskia Duyvesteyn

Ion flotation is a technique applicable to the removal of metal ions from dilute solutions, using ionic surfactants.- While there are a number of physical and chemical parameters that influence the ion flotation process, this paper focuses on two of the important chemical ones, namely frother concentration and ionic strength. The effect of several frothers, including ethanol, iso-propanol and MIBC at concentrations ranging from 0% to 0.4%, was studied for the model Cd-dodecylsulfate and Cu-dodecylsulfate systems. The ionic strength, as well as the effect of monovalent and multivalent counter ions, was also studied in the range of 1@3 - 1 M, at constant pH. The results are discussed in terms of applicability to a range of effluents from minerals and materials processing operations.

Jan 1, 1994

By Ann M. Hagni

Electric arc furnace (EAF) dust from the secondary steel industry contains lead, cadmium, and chromium that causes it to be classified as a hazardous waste. Pyrometallurgical treatment of EAF dust is directed at recovering zinc and simultaneously rendering the dust non-hazardous. The mineralogy of the EAF dust is important in determining the occurrence and phase relationships of the zinc, lead, cadmium, and chromium contents. The principle phases in EAF dust as determined by reflected light microscopy, SEM-EDS, and XRD are solid solutions of the iron spinels (franklinite, magnetite, and jacobsite), zincite, hematite, and Ca-Fe-Si glass. Chromium is present in small amounts in solid solution in the spinels. Cyclone sizing of the minus 53 pm particles shows that more than 50% of this size fraction are less than 10 pm in diameter. The <I0 pm particles contain zinc as both franklinite in solid solution with magnetite and jacobsite, and zincite as determined by transmission electron microscopy and XRD. Auger electron spectroscopy did not detect coatings of volatile phases on the surfaces of EAF dust particles.

Jan 1, 1994

By G. Roderick Eggert

Material criticality reflects the degree to which a raw material is both necessary and subject to supply-chain risks. This study compares the criticality of selected raw materials from the differing perspectives of the manufacturing sectors of China, the European Union, Japan and the United States.

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX!EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 2000

By Hani Henein

"Heat transfer between droplets/particles and a gas phase plays an important role in the transport of numerous materials processing operations. These include rapid solidification operations such as gas atomization and spray forming, as well as chemical systems such flash furnaces. Chemical reaction rates and solidification are dependent on the rate of gas-particle or gasdroplet heat transport. Using a heat transport model validated using single fluid atomization of molten droplets; the effect of process variables on heat losses from droplets was examined. In this work, the effect of type of gas, droplet size, gas temperature, gas-droplet relative velocity on the heat transport from AA606 l droplets was examined. The most critical of these process variables to heat transfer is identified and will be presented.IntroductionIn materials processing, droplets are often encountered and used in processing a wide range of liquids and slurries. The small size of the droplet enables high reaction rates or high solidification rates in many systems. In order to capitalize on these high rates of transport processes, sprays are· also developed to maximize throughput. The design of these sprays, however, does not account for the transport steps and rate limiting mechanisms at the droplet surface. Rather, spray design focuses on maximizing the break-up of a stream or slurry into small size droplets or controlling the spread of the spray. Spray systems in industrial use typically generate droplets of wide size distribution leading to a wide range of reaction times for each of the droplets. Often the generation of a spray involves a number of coupled phenomena such as stream break-up, droplet-gas transport, droplet size distribution and spray geometry. Using gas generated sprays, it is not possible to identify how individual process variables contribute and control each of these coupled phenomena. While many mathematical models have been developed of sprays and they attempt to simulate coupled droplet transport, they do not provide insight into the contributions of different mechanisms in heat transfer. This is primarily because the basic fundamental heat transport between droplet and gas cannot be isolated from other gas spray phenomena experimentally such as two-way thermal coupling [l]. Thus, experimental validation of heart transfer of large and complex industrial spray models is not carried out. Hence, the validity of spray models remains in question and the approach required to optimize spray processes cannot be clearly identified"

Jan 1, 2004

By David Seymour

Newmont Gold Company (NGC) located in Northeastern Nevada has been processing carbonaceous and sulfide refractory gold ores through a chlorination circuit prior to cyanidation. A "Flash Chlorination" pilot plant was installed in 1987 in an effort to obtain higher chlorine utilization efficiency and increase gold extraction. The Flash Chlorination process oxidizes organic carbon and sulfide sulfur. It also deactivates preg-robbing carbon, making the ore amenable to cyanidation. Significant recovery improvements were observed using this new process. This scheme has also been instrumental in the processing of higher than normal grade ores at economic chlorine levels. The Flash Chlorination pilot plant has been successfully treating carbonaceous ore on a production scale since April 1988. This paper summarizes laboratory and pilot plant optimization test work, using conventional and statistical methods.

Jan 1, 1989

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By C. F. Ferron

A process has been developed to treat the copper gold ores from the Guelb Moghrein mine in Mauritania. The process consists of pressure leaching the sulphide concentrate, neutralising with the oxide ore, recovery of copper by SX/EW and of gold by cyanidation of the autoclave residue. This paper focuses on the pressure leaching step, and presents data from bench and pilot plant test programs. In particular, attention is drawn to the effects of temperature, grind size, neutralisation, retention time and solution recycle on the kinetics of copper dissolution from various flotation concentrates. Likely leach mechanisms are briefly discussed.

Jan 1, 2000

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at &apos;higher overpotentials.

Jan 1, 1998

By Takahiko Okura

Japanese non-ferrous industry introduced large-scale smelting plants along seashores for overseas concentrates with increasing demand of metals around 1970s. Although serious environmental pollution became obvious, with economic growth, the industry got rid of pollution by installing new processes and improving operation technologies. At present, over 99.8% of sulfur input to smelters is fixed as stable compounds. Through those decades Japan had steep rises of oil prices, sudden change of exchange rate, and inadequate treating charges, we were faced to consider the closure of smelters. The industry has survived by increasing productivity, saving energy and reducing manpower. Furthermore the industry made great effort to recycle valued metals from scraps and wastes for the resources-recycling society. Academic research also contributes to support these individual technologies. Thus the industry has fostered world-acclaimed technologies in terms of efficiency and energy conservation. This paper presents technology development and environmentally-benign sulfide smelting processes.

By N. A. Vatolin, L. I. Leontjev, S. V. Shavrin

The ever growing interest to the complex iron ores may be attributed to possible production of the naturally alloyed metals and the efficient recovery of the associated elements. However, the conventional technique for complex ore processing is complicated and in some cases even impossible. A pyrometallurgical benefiation of such ores without melted slag formation has been advanced. A version of the technique assumes pellet production with metal coagulated within a slag shell on grinding the pellets, the metal phase is mechanically separated from the slag shell. The technique has been run up with ferro chromo nickel, high-titanium, high-magnesia, alumina phosphorus ores and concentrates. Another version of the pyrometallurgical benefication without melted slag formation in a rotary kiln has been developed from the schemes for processing red mud of alumina manufacture and high-titanium concentrates. Means have been put up to improve schemes available for lex iron ore processing with primary emphasis on material pretreatment before blast furnace and steelmaking processes. Vanadium-bearing titanomagnetite conentrate oxidized pellets possess low strength at reduction. The technique suggested for pelletizing in the controlled atmosphere improves the afore said pellet metallurgical properties. Prodution of metallized pellets in a conveyor roasting machine holds considerable promise for blast furnace and steelmaking processes. In processing the high-sulphur iron ores still another technique is proposed to roast the fluxed pellets with 95% and more desulphuration.

Jan 1, 1988

By Laihua Wang, Peter Hayes, Hae-Geon Lee

"This paper introduces a new process for the efficient removal of dissolved gases and inclusions from liquid metals. This process involves the creation and dispersion of fine bubbles in molten metals by introducing inert or reactive gas into a region of turbulent flow. The highly turbulent metal flow splits the gas into fine bubbles and results in good mixing between the gas and molten metal phases. These conditions are ideal for contacting inclusions in the metal with the bubbles and subsequent flotation of the inclusions to the metal-slag interface where the inclusions are then absorbed by the covering slag layer. Dissolved gases, such as [H], [0], [N] in the metals are also transferred to the gas bubbles and removed from solution.The process concept has been previously demonstrated using a full-scale air/water model to simulate the ladle-to-tundish system of continuous casting of steel. The present cold modelling work has further demonstrated the ability of the process to remove gas solutes. The results indicate that the efficiency of new process is several hundred times greater than that of conventional high speed rotating injectors which are currently applied in the treatment of liquid light metals.IntroductionDuring metal smelting, refining and alloying processes, unwanted gas and second phase liquid or solid impurities are incorporated into liquid metals. In the case of steelmaking, the gas-forming impurities include [0], [H] and [N], and the solid impurities as a result of deoxidation include Ah03, Si02 inclusions. Common impurities in liquid aluminium are dissolved hydrogen and solid Ah03. To avoid subsequent problems during processing and to improve the physical properties of the metal products it is necessary to significantly reduce the level of impurities."

Jan 1, 1996

By Richard P. Roberts

This paper will discuss the methods for the cooling of aluminum melting furnace? dross .and their impact on the environment. Also discussed will be a case history of an AROS Dross Processor installation, which is designed to maximize the recovery of metal content of the dross in a manner which is not only environmentally cleaner, but which also prepares the output in such a way as to facilitate downstream processes. Handling of the discharged material will be discussed in regards to the recycling of the preserved metal content and deposition of the unusable-materials.

Jan 1, 1992

By J. Tang, B. Q. Li, R. Akarapu

"An integrated model is developed to represent the three-dimensional electromagnetic wave propagation and thermal phenomena during microwave heating of ceramics and dielectric/biological materials. The model development is based on the edge finite element formulation for electromagnetic fields and the node fmite element formulation for thermal phenomena. Results are presented and compared well with available analytical solutions and experimental measurements. With the model, the effect of sample positions on the electromagnetic and thermal field distributions is studied.IntroductionMicrowave, as an electro-heating source, has been widely used in the processing industries for packaged foods and other materials. The commonly used household microwave oven is a typical example of microwave heating processes. Other industrial microwave processing systems include large-scale microwave guides and cavities, which are used for the sintering operations as required for making ceramic components or for sterilizing the packaged foods."

Jan 1, 2004