Search Documents

By D. Gregurek

In non-ferrous metal furnaces the installed magnesia-chromite refractory lining is exposed to several stresses, rather complex in their interaction. Therefore, a detailed investigation and understanding of wear mechanisms through “post mortem studies” is an important prerequisite for refractory producer. Additionally, in order to determine the most suitable refractory products and to improve the lining life of refractories, practical corrosion testing with processing slags is performed. For this purpose the test-facilities, such as induction furnace, rotary kiln but also cup test and drip slag test, allow the best possible understanding of chemothermal brick wear on pilot scale. Prior to testing a complete mineralogical investigation, thermo-chemical calculation via FactSageTM of the slag was carried out. Based on such research results, combined with specific process knowledge RHI Magnesita can recommend appropriate brick lining solutions for non-ferrous metal furnaces.

By Sridhar Komarneni

"Microwave-hydrothermal processing is a novel technique which combines the conventional hydrothermal processing with microwave field and we previously showed for the first time, that ceramic powders can be rapidly produced by this technique. This review paper deals with the synthesis of unary oxides such as Fe203, Ti02, Zr02, etc., binary oxides such as BaTiO3, SrTiO 3, PbTiO 3, SrZrO 3, KNbO3, etc., and ternary oxides such as NaTi2 (PO4)3 and pyrochlore phases of Pb(Mg1/3Nb2/3)O3, Pb(Zn1/3Nb2/3)O3 etc. and metal powders such as Cu, Ni, etc. below 195°C. This method can be adopted to the synthesis of a large variety of powders by the appropriate control of pH, Eh, temperature/pressure and concentration of chemical species. The main advantages of this method compared to conventional hydrothermal processing are (a) it increases the kinetics of reaction by one to two orders of magnitude, and (b) it can lead to novel phases especially those with layered structures.IntroductionConventional hydrothermal processing is a well-established synthesis technique which has been extensively used in the preparation of fine ceramic powders [1-5], large single crystals [6-8] and massive cement blocks [9]. Technologically important ceramic powders such as BaTiO 3, Al203 etc. made by the hydrothermal process are now commercially available. Although there are numerous methods for materials synthesis, hydrothermal method is truly a low temperature and environmentally benign process. For example, ZrSi04 (Zircon) which is extensively used in ceramic industry can be prepared hydrothermally at 150·C [10] compared to sol-gel or solid-state method [11,12] which require a temperature of about 1000·C. The hydrothermal method is environmentally benign because hydrothermal reactions are carried out in closed systems at low temperatures and the contents can be recovered and recycled after cooling to the ambient conditions. One of the disadvantages with any low temperature processing method is slow kinetics. For this reason we have combined the hydrothermal method with microwaves to enhance kinetics and we named this method as ""Microwave-hydrothermal"" processing [13- 16]. Although the combination of microwave and hydrothermal techniques has been used in the past few years to dissolve all kinds of inorganic (e.g. alumino silicate rocks) and organic materials rapidly for chemical analysis, we were the first to show its potential value for the synthesis of various ceramic powders [13-16]. In this paper, I show that this novel method is applicable to the synthesis of all unary, binary and multinary oxides by the appropriate control of pH, Eh, temperature, pressure and concentration of chemical species. In addition, this method is also found to be useful for the preparation of metal powders."

Jan 1, 1994

By S. Peng, Vaughan R. Voller

"Free boundary problems are a common occurrence in materials processing operations. An important example is the filling of material into molds. This paper looks at filling problems associated with polymer processing, in particular Resin Transfer Molding (RTM) and Compression Molding. A general, single governing equation is developed which on numerical solution provides predictions for the position of the polymer front in the mold during filling. Both fixed and deforming finite element solutions are developed. Application to polymer filling test problems reveal that the fixed and deforming grid scheme are accurate and compare closely with each other.IntroductionProblems arising from the analysis of material processing operations often involve the tracking of a moving boundary, on which a balance conditions needs to be met, or the locating of a free surface that defines the solution domain. Material processing examples of so called ""free and moving boundary problems"" include; the tracking of solidification/melting fronts[l], the tracking of the metal/gas interface during the filling of a mold[2] and location and shape of a skull (freeze line) in a melting furnace[3].Computational solution of free and moving boundary problems usually fit into one of two classes, viz.1. Fixed grid scheme: In which the spatial domain is covered by a fixed grid (mesh) of node points and the solution uses an auxiliary variable (e.g. a local liquid fraction) to track the moving boundary or locate the free surface.2. Deforming grid scheme: In which the grid in the spatial domain is continuously deformed (or adapted in a steady state problem) such that a specified set of grid points lie on the moving boundary or the free surface.Details on the basic underlying features in these two classes of solution can be found in the excellent monograph by Crank [4]."

Jan 1, 1994

By Ki Bui Ma

Momentum wheels with superconducting bearings can integrate both attitude control and energy storage functions, with attendant savings in the total volume and weight of hardware, and power consumption, all of which are in short supply on mini-satellites. We have built and tested a prototype with a wheel of mass 1.9 kg, diameter 3.25 in, and height 3 in, which can store 3.5 J-sec of angular momentum and 5 kJ of energy when it rotates at an angular speed of 15000 RPM. The energy density of 2.5 kJ/kg achieved is comparable with the lower range for lead-acid batteries. To show that the wheel is energy efficient, we have performed spin down tests and measured the input power required to sustain rotational speed. Results indicate that power consumption, even accounting for the needs of cooling system, is significantly smaller than that for state of the art commercial reaction wheels.

Jan 1, 2002

By C. Sui

A common objective in many Cu/Zn concentrators is to reduce the loss of Zn to the Cu-concentrate. One suspected source of the problem is accidental activation of sphalerite by heavy metal ions such as lead. One method of quantifying surface metal ion concentration is extraction with ethylene-diamine-tetra-acetate (EDTA). This was used to survey Cu-rougher flotation at three Cu/Zn concentrators: Les Mines Selbaie, Falconbridge's Kidd Creek division, and Hudson Bay Mining and Smelting Although all have less than 0.2% galena in the ore, Pb ions proved an abundant extractable metal. From a laboratory study a model of surface coverage of lead species generated by an ore was combined with an estimate of surface concentration of lead required to activate sphalerite to explore the possibility of accidental activation. Ores with Pb-grade as low as 0.1% can produce sufficient Pb to be a potential problem.

Jan 1, 1999

By Zhigan Deng

Ni–Mo ore is a black shale containing amorphous colloidal sulfides which have highly active. The oxygen pressure leaching behavior of nickel from black shale in aqueous media is presented. The effects of agitation speed, temperature, oxygen partial pressure and particle size on the rate of nickel leaching were determined. The results indicate that at low temperature hydrothermal and excess oxygen presence, the amorphous sulfides are easily oxidized to sulfuric acid and sulfate, and leaching nickel. The mathematical analyses of the experimental data for various experimental conditions indicated that the dissolution process was controlled by the chemical reaction during the early stage of dissolution, and was then controlled by liquid-film diffusion. In the initial stage of leaching, the reaction depends on oxygen partial pressure.

By Lv Guozhi, Niu Liping, Shi Guanyong, Liu Yan, He Jicheng, Du Yanjun, Dou Zhihe

"We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The alloy prepared in different process conditions was characterized via XRD, SEM, OM and TEM and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that there are three distinct regions: copper-rich regions, chromium-rich regions and the inclusion regions. Inclusions are mainly in the form of stomata and Alz03 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Adding Na3AlF6 and heating agent can effectively reduce the inclusion content in the alloy.1 IntroductionIn recent years, with the development ofhigh power vacuum and high-pressure technology ,the CuCr alloy contact material which has many advantages gradually replaced the traditional W-Cu and Cu-Bi series alloy contact material, and become the first choice of material in high-voltage and high-power vacuum switch contacts['-3l. The traditional powder metallurgy method, infiltration method and vacuum arc melting method[4-SJ are using metal Cu powder and Cr powder as raw material by casting molding, and have disadvantages such as high production costs, complicated process, poor product density and low yield, especially in the large size alloy ingots[9-12l. At present, the world regards CuCr alloy new preparation technologies as the first place, and how to achieve a large size the CuCr alloy ingot preparation has become a hot research of CuCr alloy[3l. Zhang Ting-an and Dou Zhihe[l-3l who are supported by national natural science fundation of china successfully successful developed new technologies and core equipment to prepare large-size copper-chromium alloy through aluminum thermal reduction-secondary refining method, and obtained two national invention patents. The method includes two key steps: one is get CuCr alloy consumable ingot by Thermit-SHS with electromagnetic stirring, the other is to refme the CuCr alloy ingot to remove the pores, inclusions and other defects by electroslag remelting technology to get dense and uniform CuCr contact material. The preliminary study results show that means of electromagnetic stirring evidently inhibit effect of alloy ingot macrosegregation during the electromagnetic casting stage, but there are still microstructure defects such as alumina inclusions and pores in the alloy ingots. Therefore, Zhang Ting-an et al refer new ideas of using the electroslag remelting to refine Cu Cr alloy ingots and effectively remove the defects of the ingots such as pores and inclusions [3l _ At present, there is no report of study on the electroslag remelting refining processes of CuCr alloy (the refining slag, remelting current). This article will research mode of occurrence and distribution law of inclusions in the large-size CuCr alloy ingots by Al Thermit-SHS under magnetic field stirring action and provide a theoretical basis for chosing refining slag to remove inclusions by electroslag refining. Meanwhile the article analyses the effect of reduction conditions of Thermit-SHS on the types of inclusions, mode of occurrence and distribution of regular inclusions in alloy ingot, and refer theory for inclusions regulation in the large-size alloy ingots."

Jan 1, 2013

By Gabriel Zarate

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 tonnes of copper per year and 5.4 million tonnes of ore per year. Copper production was steadily increased reaching a maximum of 62,239 tonnes in 2012 for an ore throughput of 10,5 million tonnes. In order to get these production and throughput rates, a number of changes have been made in the metallurgical parameters of the plant operation since the start up, among them particle size, heap height, acid addition distribution in curing and leaching solution, leach cycles and pad type. Most of the modifications have been implemented after carrying out extensive column test work programs. The modifications implemented and the results obtained, as well as the test work programs carried out, are discussed in this paper.

By Roger C. Urquhart

Copper-nickel-sulphide ores mined in the Rustenburg district of South Africa are generally smelted in electric furnaces because of the high-temperature slag produced, the availability of cheap electric power, and the smaller pollution problems. Apart from melting, the functions of the electric furnace are to recover most of the matte content in the converter slag by physical and chemical interaction with the furnace bath and to provide adequate time for the optimum separation of matte and slag. Smooth, efficient operation will denend on fluid slags for settling, balanced by high resistivities to obtain adequate concentration and distribution of power by way of current heating. To obtain a greater understanding of the processes involved, an investigation was undertaken at Rustenburg Platinum Mines on the smelting of copper-nickel concentrates in a 19.5 MVA furnace with six in-line electrodes. The matte- and slag-tapping temperatures, slag temperatures, slag analyses, electrical data, and electrode position were measured. Radioactive tracers were introduced into the slag, and quantitative results relating to the flow pattern within the furnace were obtained. These studies were augmented by scaled laboratory investigations relating to the determination of cell constants and current distribution within the furnace. Instantaneous field and power distribution plots were determined by use of an on-line mini-computer. The applicability of these results to furnace operation is discussed.

Jan 1, 1976

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifYing its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multi component slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today's reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author's group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003

By E. Gratz, U. Pal, A. Powell, S. Pati, J. Milshtein

"The solid oxide membrane (SOM) process has been used at 1150 'C to produce magnesium by direct electrolysis of its oxide. Magnesium oxide is dissolved in a molten CaF2-MgF2 ionic flux. An oxygen-ion-conducting yttria-stabilized zirconia (YSZ) SOM membrane separates the cathode and the flux from the anode. During electrolysis, magnesium ions are reduced at the cathode and Mg(g) bubbles out of the flux into a separate condenser. The flux has a small solubility for magnesium which imparts electronic conductivity to the flux. The electronic conductivity decreases current efficiency of the process and also degrades the YSZ membrane. This study investigates different methods for reducing the electronic conductivity of the flux due to magnesium solubility. One effective method shown here is inert gas flushing near the magnesium nucleation site. Potentiodynamic and potentiostatic experiments along with AC impedance spectroscopy are used to characterize the effectiveness of the approach.IntroductionMagnesium is the third most abundant metal in the earth's crust. Since magnesium is the lightest of all metals used for construction alloys, magnesium is the leading candidate to replace steel and aluminum in automobiles. Automobile manufacturers would like to increase magnesium content from 4-5kg per vehicle to 40-IOOkg per vehicle [I]. Using magnesium alloys instead of steel and aluminum can reduce automobile weight and improve fuel efficiency. However, in order for automobile manufactures to make this change, it is generally believed that new cost effective methods of magnesium production must emerge.One approach for magnesium production which has been shown to be effective on a laboratory scale is the direct electrolysis of magnesium oxide utilizing an oxygen-ion-conducting solid oxide membrane (SOM), this is known as the SOM process [2]. A recent study estimated that a commercial SOM plant could produce magnesium from magnesium oxide at a cost that is 40% less than current technologies [3]."

Jan 1, 2012

By Edouard Asselin, Guikuan Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe( II )-Fe(III)-H2S04 solution at 25°C and 70 °C. Results from the calculation ofspeciation in the above solution reveal that, at both 25 °C and 70 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller values for the reversible potential of the ferric/ferrous couple based on the Nemst equation. Exchange current densities of the ferric/ferrous couple were obtained by extrapolating the cathodic linear Tafel line to the reversible potential and are on the order of 10-7·10-6 A/cm2 at 25°C and 10·6-10-5 A/cm2 at 70 °C, respectively. The transfer coefficients were about 0.35-0.38 at 25°C and 0.35-0.45 at 70 °C. Polarization plots of CPC and CPP under different nominal Fe3+/Fe2+ ratios are in good agreement at 25 ·c and at 70 °C. Based on the obtained exchange current densities, the rate constant k, was calculated and is on the order of 10-1 cm/s at 25 °C and 10 1 cm/s at 70 °C.IntroductionChalcopyrite is the most abundant copper mineral in nature, accounting for about 70% of copper reserves in the world [I]. In recent years, the metallurgical industry has been searching for a hydrometallurgical process as an alternative to pyrometallurgical treatment due to high emissions of S02 and capital costs associated with smelting. Activity in this area has increased recently due to some inherent advantages associated with hydrometallurgical processing, such as the possibility of treating low-grade ores (increasingly more abundant in the case of copper) and easier control of waste, with the attendant benefits to the environment [I]. Chalcopyrite is highly refractory under most hydrometallurgical conditions, owing to the formation of an anodic passivation layer on the chalcopyrite surface which renders the process kinetics very slow. Most of the currently proposed processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Sulfuric acid is preferred over all other leaching reagents in terms of cost, environmental friendliness, and ease of its regeneration during electro-winning. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale,"

Jan 1, 2012

By Fatma Arslan

The lateritic nickel ore sample subjected to this experimental study was taken from Çalda ore deposit (Turkey) and contains 1.43% Ni and 0.105% Co. Mineralogical investigations showed that the ore sample contains asbolane, chromite, limonite, hematite, goethite, lepidocrocite, magnetite, serpentine, and clay type minerals together with chalcedon, quartz, calcite, and chlorite. In the acidic leaching experiments, the effects of temperature, acid (H2SO4) concentration, and leaching time on nickel leaching recoveries were investigated. Leaching recovery versus time curves showed a parabolic trend and increasing the temperature shifted that curves to the higher values. The dissolution of nickel from lateritic ore can be explained by a shrinking core model and the apparent activation energy was found as 47.34 kJ/mol in the range given by the literature. The highest Ni and Co leaching efficiencies as 90.2% and 96.8% respectively were obtained at 80°C temperature, 200 g/L H2SO4 concentration, and 8 hours of leaching time.

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Guozhu Ye

Hydrometallurgical zinc recovery from EAF dust has several advantages compared to pyrometallurgical alternatives in terms of low temperature operation, lower energy consumption and higher flexibility. Many hydrometallurgical processes have been suggested and tested over the years without success. The main reasons are: -Low leaching yield of zinc due to the fact that a high fraction of ZnO in the EAF dust exists in the zinc ferrite structure which makes selective leaching of ZnO not possible -Many of the proposals could not handle the halide in the EAF dust To eliminate these two disadvantages, two zinc ferrite elimination concepts have been tested and developed in the REZIN project of the EU 5th Framework Programme. The two concepts for zinc ferrite elimination could be shortly described by the following chemical reactions: A. ZnOFe2O3 + 2CaO = Ca2Fe2O5 + ZnOfree B. ZnOFe2O3 + C = Femet + CO/CO2 + ZnOfree These two concepts were investigated in details in combination with a subsequent leaching step using the novel EZINC process for recovery of zinc from EAF dust. Leaching of pretreated samples has shown great increases of a zinc recovery yield. A zinc recovery of over 90 % could be reached, as compared to about 50 % for no-pretreated samples. This paper will describe the two concepts in details.

Jan 1, 2006

By John ?gren, Martin Schwind, Henrik Larsson

"A new model for internal oxidation, as well as similar processes, has been implemented on computer. It is based upon a combination of random walk and cellular automata and is capable of treating 3-dimensional cases. To model diffusion, it utilises quantised units of matter. All steps of the process are included: nucleation, growth and coarsening. The effect of grain boundaries on diffusion as well as nucleation is taken into account. Further possible development is briefly discussed; especially the treatment of nucleation needs further consideration. IntroductionComplex diffusion-controlled processes may now be simulated on a routine basis when concentration varies along one co-ordinate only. One-dimensional simulations capture much of the information of interest but not all. For the case at hand, especially the spatial and the size distribution of precipitates, as well as the impact of grain boundaries, would be interesting information not accessible from 1-D simulationsSolving the full Fick-Onsager law in three dimensions does not seem feasible with the computers of today. In the model described in this article, random walk by quantised units of matter are considered. The model should be useful for a number of cases involving dispersed systems. With further development, it would indeed seem possible to simulate most types of phase transformations.Previous workWe have previously published two articles [1,2] on the new approach discussed in this work. In those articles we described the basic idea and showed, among other things, that very good agreement with an experimental concentration profile can be obtained, in a single-phase system, using independently assessed thermodynamic and kinetic data. Also, Schwind used the same random walk based concept to model coarsening [3]."

Jan 1, 2001

By Ian M. Ritchie

Cementation or metal displacement reactions such as Cu2+ + Fe Cu + Fe2+ are among the oldest known hydrometallurgical reactions. They are still used in the recovery of some metals and in the purification of process liquors and waste water streams. However, they are often more complex than the stoichiometric reaction would suggest because they involve the simultaneous deposition of one metal onto a second which is dissolving. For example, sometimes a cementation will not take place, even though it is thermodynamically favoured. On other occasions, a cementation reaction will start but come to a halt as the depositing metal blankets the reacting surface. On yet other occasions, side reactions, catalyzed by the deposit, can be important. In this paper, the electrochemical basis of cementation reactions is described. The conditions for each of the complications encountered in these reactions are described and illustrated by examples drawn from a number of hydrometallurgical processes. The cementation reaction between activated carbon and gold thiosulfate is also briefly described, this reaction being unusual in that no dissolution of the carbon occurs.

Jan 1, 2003

By Florian Kongoli

The optimal operation of the blast furnace depends considerably on the properties of the sinter fed into the furnace. As a result, the optimization of the sintering processes has a direct effect on the overall effectiveness of the iron making processes. In order to produce a good sinter special care needs to be taken in order to assure it has a good permeability and reducibility and it is able to retain these properties for a certain time. If the sinter starts to melt down early in the upper part of the blast furnace, where its solid state reduction is essential, permeability decreases, the gas channels get blocked, reductibility diminishes and serious problems may also follow. Among the factors that influences the above mentioned sinter properties are the oxygen potential and fluxing components. Nevertheless, their effect on the phase relations during sintering and sinter reduction conditions has not yet entirely clarified and confusion exists in literature. This quantification becomes even more important today where many new minor components such as Al2O3 and MgO enter the sinter through raw materials. This work quantifies the effect of oxygen potential and fluxing components such as alumina and magnesia on the liquidus and phase relations of the sinter primary melts in the iron rich portion of CaO-FeO-Fe2O3-SiO2 system at sintering conditions. This is carried out by the means of new type of industrial diagrams in the form of Fe/CaO vs. SiO2 that can directly help the optimization of the sintering processes.

Jan 1, 2006

By Manuel Pérez-Tello

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. Oxygen concentration in the process gas was set to 40 and 70% by vol. and a heating rate of 40 °C/min was used. Response variables included: the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology, and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles, and by thermochemical and mass balance calculations to reproduce the DSC and TGA thermograms. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction for each mineral as a function of time. Experiments conducted with copper concentrate particles containing the minerals studied suggest that the reaction mechanisms for the individual minerals can be used to represent the oxidation behavior of the copper concentrate particles.

Jan 1, 2006

By Rafael Padilla

The recovery of copper from chalcopyrite concentrates by leaching is difficult due to the slow dissolution kinetics of this mineral in most leaching media. However, recovery of copper from sulfidized chalcopyrite (a mixture of CuS and FeS2) by leaching is faster and could be selective depending on the leaching media. In this paper, the result of an investigation on the H2SO4-O2 pressure leaching of sulfidized chalcopyrite is presented. The variables considered in the study were stirring speed, concentration of sulfuric acid, temperature, and partial pressure of oxygen. The experimental data indicated that stirring speed over 500 rpm and sulfuric acid concentration over 0.1 M had very little effect on the leaching rate. An increase in temperature from 90 to 100 ºC increased both copper and iron dissolution; however, further increase to 120 ºC affected negatively the copper dissolution. Oxygen partial pressure was found to be the main variable that controls the copper/iron selectivity of the leaching. An increase in oxygen partial pressure increased significantly the rate of copper dissolution but deteriorated the copper/iron selectivity. The analysis for sulfur of the leaching solid residues indicated that most of the copper sulfide sulfur in the sulfidized concentrate oxidized to elemental sulfur.

Jan 1, 2006