Search Documents

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

By Zhengdong Liu, Kaizhong Zhang, Zhaonan Jiang, Yuanping Cheng, Biao Hu, Qingquan Liu, Ranpeng Wang

"Major coal mining areas in eastern China have entered into the deep mining state. Gas pre-drainage, which has been successful at shallower depths, is not suitable at greater depths because of complex conditions. Coal permeability, which is closely related to the damage behavior of coal, is the most important parameter in determining gas migration and gas drainage in a coal seam. To achieve an optimal gas drainage design in a deep mining state, the damage and permeability evolutions of coal should be further studied. The progressive failure process of coal has been analyzed by conducting a series of triaxial loading and unloading tests. The development of coal fractures has been successfully quantified, and the corresponding characteristic stress points have been obtained by using Martin’s fracture model and the stress-strain curve. Coal will produce plastic deformation, and its permeability will rapidly increase when the stress level reaches damage expansion stress. INTRODUCTION Coal mine methane (CMM) is a general term for all methane released during and after mining operations. CMM is both a potentially valuable energy and a serious hazard in active coal mines. Degassing coal seams is important for mitigating this hazard and results in the beneficial recovery of a cleanburning, low-carbon fuel resource (Karacan, Ruiz, Cotè, and Phipps, 2011). The permeability of coal is a key parameter in determining CMM production, coalbed methane (CBM) production, CO2-enhanced coalbed methane (CO2-ECBM) production, and CO2 storage in coal seam reservoirs (Connell, Lu, and Pan, 2010; Chen et al., 2011; Perera, Ranjith, and Choi, 2013). Significant research has been condcuted to the study of the evolution of coal permeability. These studies revealed that coal permeability evolution is controlled by the competing influences of effective stress and sorption-induced coal deformation. Chen et al. (2011) investigated the influence of an effective stress coefficient and sorption-induced strain on the evolution of coal permeability. Robertson and his team (Robertson, 2005; Robertson and Christiansen, 2005) measured sorption-induced matrix strain and permeability changes with regard to CO2, CH4, and N2. They found that the compressibility is not constant in a natural coal sample. Karacan (2007) conducted a series of experimental tests to study the swelling-induced volumetric strains internal to a stressed coal associated with CO2 sorption. Liu et al. (2016) investigated the effects of matrix swelling area propagation on the permeability evolution by using both natural and reconstituted samples. Many coal permeability models have been developed to describe the permeability evolution under uniaxial loading, biaxial strain, hydrostatic confining pressure, triaxial strain, and triaxial stress. Recently, some analytical permeability models have been developed to describe the anisotropic permeability behavior (Palmer, 2009; Pan and Connell, 2011; Robertson and Christiansen, 2005; Wang, Zang, Wang, and Zhou, 2014; Chen, Pan, Liu, and Connell, 2012)."

Jan 1, 2017

By Bill A. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six-head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin.The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill.The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator's station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt, and mesh sump.The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in tum lowers the miners' roof exposure per cut. This design reduces the operator's exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore, the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely."

Jan 1, 2016

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By Peng Zhang

In a recent research effort, a laminated overburden loading model (as implemented in LaModel3.0 was compared with the results of ARMPS 2010, and the laminated overburden model was found to more accurately classify a ARMPS database of 52 deep cover case histories by a factor of 60% versus 54%. However, the LaModel analysis of each case study required several days to complete, as compared to a requirement of only several minutes for each ARMPS analysis. In the research presented in this paper, a computer code (ARMPS-LAM) has been developed to effectively implement the laminated overburden model into the ARMPS program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition and then automatically develops, runs, and analyzes a full LaModel analysis of the mining geometry to output the stability factor on the Active Mining Zone(AMZ), all without further user input. The present laboratory version of ARMPS-LAM can be run in batch mode; therefore, the ARMPS 2010 database of 645case histories can be analyzed very quickly. In an initial logistic regression analysis of this database, the ARMPS-LAM program was seen to be slightly more accurate than ARMPS 2010 by a factor of 71% versus 63%.

Jan 1, 2013

By Zach G. Agioutantis

The Illinois Basin has an extensive history with the use of mechanized longwall mining dating back to the early 1970?s. In recent times, technological advances have resulted in increased panel widths from 800 feet to over 1400 feet and daily panel advance rates have also increased significant l. The prediction and control of subsidence and surface deformation due to underground mining are important considerations in the permitting, planning, and monitoring of these coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology, well utilized in the Illinois basin, and widely used by researchers and planning engineers around the world. This paper utilizes subsidence data, recently measured in longwall operations in Illinois, to develop an updated ground movement prediction capability implemented by the Surface Deformation Prediction System (SDPS) software package.

Jan 1, 2014

By Jesse L. Craft

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops. Sag subsidence develops where the pillars are failing in conjunction with roof failure. Overburden thickness is generally greater than 150 feet. Beam subsidence can occur in all terrains. It is associated with retreat mining and room and pillar mining where pillar crushing or pillar compression has taken place and barriers are left inplace. They occur as beam arch or one-sided beam subsidence. Beam arch failure occurs where mining has taken place on both sides of a coal barrier. One-sided beam failure is associated with retreat mining moving from a barrier towards the entry in hilly topography. This type of subsidence occurs where a hard, thick, rock unit is acting as a bridge supporting the overburden and outcrops on the hill side.

Jan 1, 1992

By Morgan M. Sears, Gamal Rashed, Jim Winfield, Brent Slaker

"Over the past decade, ground falls have resulted in five fatalities, representing over 40% of all fatalities occurring in underground stone mines in the United States. In conjunction with recent high-profile pillar collapses, the need for further ground control research in the nation’s stone mines is evident. Ground conditions are growing more difficult. Therefore, this research is focused on deep cover, steeply dipping, and multi-level underground nonmetal mines. The objective of this paper is to introduce a geomechanical study of pillar development in a steeply dipping limestone deposit. To accomplish this, a numerical model was developed using input from modified laboratory test data and in situ stress measurements provided by the mine to simulate the development of a pillar under these conditions. The model was then verified against field observations and stress mapping. The calibrated model was then used to calculate the estimated stresses in the pillar and immediate roof as development progresses around an instrumented pillar.INTRODUCTIONGround falls represent a significant hazard in the nation’s underground stone mines. In response to recent large-scale pillar collapses, as well as stakeholder interactions, researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at mines operating in challenging operational environments. These include deep-cover, steeply dipping, and multi-level mines where there is the potential for an increased risk of ground failure. The Pleasant Gap Mine, shown in Figure 1, operates in the Valentine Formation, which is typically light grey, extremely fine-grained limestone, and approximately 21.3 m (70 ft.) thick. The Centre Hall Formation makes up the immediate and main roof members and is approximately 9.1 m (30 ft.) thick, consisting of medium-dark-gray limestone (Murphy et al., 2018). Situated in a syncline, the top of the Valentine Formation dips at approximately 19° with a strike of approximately N54E in the area of interest (see Figure 2)."

Jan 1, 2018

By William J. Conrad, Ryan J. Molka, Erik C. Westman

"In order to study pillar and overburden response to retreat mining, a ground control program was conducted at a Central Appalachian mine. The program consisted of several monitoring methods including a seismic monitoring system, borehole pressure cells in the pillars, and time-lapse photogrammetry of the pillar ribs. Two parallel geophone arrays were installed, one on each side of the panel with the sensors mounted 3m (IO ft) into the roof. A total of fourteen geophones recorded more than 5,000 events during the panel retreat. A MIDAS datalogger was used to record pressure from borehole pressure cells (BPCs) located in two adjacent pillars that were not mined during retreat. A series of photographs were taken of the pillars that had the BPCs as the face approached so that deformation of the entire rib could be monitored using photogrammetry.Results showed that pillar stability and cave development were as expected. The BPCs showed an increase in loading when the face was 115 m (380 ft) inby and a clear onset of the forward abutment at 30 m (100 ft). The photogrammetry results displayed pillar deformation corresponding to the increased loading. The microseismic monitoring results showed the overburden caving inby the face, again as expected. The significance of these results lies in two points, I) we can quantify the safe manner in which this mine is conducting retreating operations, and 2) we can use volumetric technologies (photogrammetry and microseismic) to monitor entire volumes of the mine in addition to the traditional point-location geotechnical measurements (BPCs).INTRODUCTION AND BACKGROUNDExcavation of underground openings is a difficult job in a challenging environment. The rigor of the process is compounded by the lack of a method that allows quantification of changes within the rock mass as excavation progresses. Statistics kept by the Department of Labor, Mine Safety and Health Administration show that 16% of fatalities and lost time incidents in the underground mining industry are due to unexpected rock mass failure (MSHA, 2015). A recent example is the Crandall Canyon, Utah, coal mine accident caused by the vertical collapse of a longwall coal mine on August 6, 2007 (Dreger, Ford, Walter, 2008)."

Jan 1, 2016

By Elia Elias, Alan Crosky, Paul Hagan, Damon Vandermaat, Serkan Saydam, Peter H. Craig

"The University of New South Wales (UNSW Australia) had been involved in the study of premature failure of rock bolts in Australian coal mines from the initial identification of the problem in 1999 (Crosky et al 2002). Rock bolt steel changes over the last decade appear to have not reduced the incidence of failures. A broadened UNSW research project funded by the Australian Research Council (ARC) and Industry has targeted finding the environmental causes through extensive field and laboratory experiments. This paper describes the field studies conducted in underground coal mines, in particular attempts to measure the contribution to corrosion from groundwater, mineralogy and microbial activity. Various underground survey techniques were used to determine the extent of broken bolts, with the presence of both stress corrosion cracking (SCC) and localized deep pitting making no single technique suitable on their own. Groundwater found dripping from bolts across various coalfields in Australia were found to be not aggressive and known groundwater corrosivity classification systems did not correlate to where broken bolts were found. In-hole coupon bolts placed in roof strata containing claystone bands confirmed the clay as being a major contributor to corrosion. Microbes capable of contributing to steel corrosion were found to be present in groundwater, and culturing of the microbes taken from in-situ coupon bolts proved that the bacteria was present on the bolt surface. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of 1) helping quantify newly developed corrosivity classification systems, 2) providing an in-situ ground support corrosion monitoring tool, and 3) for testing possible corrosion protection solutions.introductionThe problem of premature rock bolt failure in Australian coal mines was published in 2002 and 2004 by UNSW Australia from Australian Coal Association Research Program (ACARP) funded projects. The majority of the broken bolts examined had steel Charpy impact toughness values of 4 – 7 Joules, and the failure mechanism was most often stress corrosion cracking (SCC). Steel fracture mechanics predicts that an increase in impact toughness will increase the length of the crack before sudden brittle failure. In the final report of 2004, anecdotal evidence from one coal mine indicated that the problem may be eliminated in some environments by a change to steel grades with higher Charpy impact values of ~16. (Crosky et al, 2002 and 2004)"

Jan 1, 2015

By Elizabeth Holley, Meriel Young, Gabriel Walton

"The coal mine roof rating (CMRR) was developed by Chris Mark and Greg Molinda to bridge the gap between geological variation in underground coal mines and engineering design. The CMRR accounts for the compressive strength of the immediate roof, the shear strength and intensity of any discontinuities present, and the moisture sensitivity of the immediate roof. The CMRR has been widely used and validated in Eastern US coal mines, but it has seen limited application in the Western US.This study focuses on roof behavior at a Western coal mine. Mine A shows significant lateral geological variation, along with localized faulting and a laterally extensive sandstone channel network. The CMRR is not used to predict roof instability at the mine.It is, therefore, hypothesized that there are other factors that are correlated with roof instability in underground coal mines that could potentially also be included in the CMRR.This hypothesis was tested by collecting 30 CMRR measurements at Mine A. At each measurement location, a binary record of the roof condition (stable or unstable) was made along with parameters, such as depth of cover, thought to also correlate with roof stability. A statistical analysis of the data was performed to determine the parameters in addition to those included in the CMRR, which can be correlated to roof stability.INTRODUCTION AND BACKGROUNDRoof fall is one of the greatest hazards facing underground coal miners (Barczak et al., 2000). In 2017, 91 lost-time injuries occurred due to roof fall in US underground coal mines. A further 48 roof falls occurred with no lost days (MSHA, 2018).The coal mine roof rating (CMRR) classification was developed by Molinda and Mark (1994) to quantify the geological description of mine roof into a single value that could indicate mine roof stability and be used in engineering design. It is widely used in the Eastern US as an input for the analysis of longwall pillar stability (ALPS) in underground coal mines. It provides an excellent start; however, it is arguably not fully comprehensive, nor is it widely used in the Western US."

Jan 1, 2018

By Pierre-Yves Declercq, Andre Vervoort

"After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—an upward movement. Although most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method, surface movement still occurs many decades after mining is terminated. After the closure and flooding of underground excavations and surrounding rock, this movement is reversed. This paper focuses on quantifying the upward movement in two neighboring coal mines (Winterslag and Zwartberg, Belgium). The study is based on data from a remote sensing technique: interferometry with synthetic aperture radar (INSAR). The results of the study show that the rate of upward movement in the decade after closure is about 10 mm/year on average. The upward movements are not linked directly to the past exploitation directly underneath a location. The amounts of subsidence at specific locations are linked mainly to their positions relative to an inverse trough shape situated over the entire mined-out areas and their immediate surroundings. Local features, such as geological faults, can have a secondary effect on the local variation of the uplift. The processes of subsidence and uplift are based on completely different mechanisms. Subsidence is initiated by a caving process, while the process of uplift is clearly linked to flooding. INTRODUCTION After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—upward movement in the area above the past exploitation and in the immediate surroundings. Of course, most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method (Peng, 1986). This downward movement continues to occur at a smaller rate many decades after mining has been terminated when the water in the underground excavations is pumped to the surface. This is the case as long as a mine is in operation. However, after the closure and flooding of the underground excavations and the surrounding rock, this movement is reversed, and the surface is uplifted. A total uplift of about half a meter has been recorded to date. This phenomenon has been described in several different coal basins in Europe, for example, in Belgium (Devleeschouwer et al., 2008), France (Samsonov, d’Oreye, and Smets, 2013), Germany (Baglikow, 2011), the Netherlands (Caro Cuenca, Hooper, and Hanssen, 2013), and Poland (Preusse, Kateloe, and Sroka, 2013). To date, research has focused mainly on understanding the phenomenon (e.g., Herrero et al., 2012) and identifying general trends, whereby the link with the rise in water levels is an important issue (Caro Cuenca, Hooper, and Hanssen, 2013). The most accepted explanation is linked to the swelling of clay minerals in the argillaceous rocks in the coal strata (Herrero et al., 2012). Without doubt, the full explanation is complex, and swelling is probably not the only cause of the residual movement. Most coal strata rock is weakened upon contact with water. The increase in water pressure also results in a decrease in the effective stress. Both aspects facilitate the fracturing of rock, which normally would result in further subsidence. However, decreases in the effective stresses also result in the relaxation or expansion of the rock, which induces an upward movement (Fjar et al., 2008). All of these aspects, including the long-term residual subsidence due to compaction under dry conditions, result in a net upward movement. The phenomenon discussed here is clearly different from the upsidence, sometimes observed on other continents (e.g., in Australia, Galvin, 2016). When upsidence occurs, the rock near the surface bends and buckles upwards due to the overstressing of the floors of the valleys."

Jan 1, 2017

By Katya V. Babenko, Victor V. Nazimko

We address the problem of the stochastic nature of ground pressure manifestation. Stress distribution in a rock mass and ground irreversible movement are governed with a set of random factors that affect the over-peak strength of the rocks, making them extremely sensitive to any perturbation of the external environment and to internal fluctuations of the thermodynamic state of the rock. We investigate the fluctuation evolution during a longwall face movement to find out whether the fluctuation dissipates or builds up. Five adjacent powered support failures simulate the ground pressure fluctuation. The main roof has been presented as a plate that reposed on the rigid base. The stiffness of the base depends on the thickness of the extracted coal seam and on the dilation of the caving roof. Maximum stiffness occurs in situ, and minimum stiffness is in the gob when the roof is highly flexible and subsides elastically, without caving. The more stress acts in the roof, the higher the cavity that occurs and the larger increment of the base stiffness. The wave of the fluctuation has extended both to the direction of the longwall advance and along the face from the point of the fluctuation agitation. There was an incubation period when the fluctuation was negligible, and the process of the main roof caving remained unaffected. The distance of the longwall advance during the incubation period was twice the longwall length when the fluctuation magnitude was 1% relative to the maximum possible disturbance and 0.76 of the longwall length for the magnitude of 24%. However, the pattern of the roof caving has dramatically changed during further movement of the longwall. All caving parameters have changed: step of the caving, ground pressure distribution, and the manifestation in the longwall and entries. A histogram of the fluctuation magnitude is symmetric in accordance with normal distribution. However, the distribution has abnormal excess. These findings are the first step toward answering the question whether it is possible to forecast the process of main roof caving and weighting consistently. Our preliminary conclusion is that the space and time intervals where this prediction can be made with certain reliability are limited, so further investigation is needed.

Jan 1, 2017

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By William Blake

Mining induced rock bursts have been a severe operational hazard associated with the deep silver mines of the Coeur d'Alene mining district for over 30 years. Recent studies during the past fm years have led to a better understanding of the different types of rook bursts and their causative mechanisms. This has resulted in ground control measures that more effectively minimize burst occurrences as well as contain burst damage. Case histories of burst incidences and examples of control measures are presented.

Jan 1, 1987

By John C. Stankus

The 3 Right pre-developed longwall recovery entry at Signal Peak Energy?s Bull Mountain No. 1 mine was designed to prevent the abnormal roof conditions encountered in its firsttwo recovery entries. Unique geological conditions, such as the low overburden of approximately 200 feet and prevalence of roof joints in the sandstone overburden, contribute significantly to abnormal conditions during longwall recovery. The 3 Right recovery entry was 42 ft wide and developed in two stages, 21 ft wide in each stage. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, high-capacity primary bolts and cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. The roof bolting and backfilldesign were based on current practices in this mine and successful practices in other mines in the U.S. and Australia. Extensive instrumentation was installed in the recovery entry for continuous monitoring of load transfer as the face approached and cut into the recovery entries. The support design was completely successful with a smooth cut-through on January 29 and 30, 2014, significantly reducing the shield recovery time and meanwhile protecting the safety of miners. Based on actual observance and practices of the 3 Right recovery entry, recommendations on improvement and modificationsof roof support for 4 Right recovery room are presented.

Jan 1, 2014

By Darin Cotton, Tim Burgess, Tim Martin

"As the leading US supplier of roof control drills, J. H. Fletcher and Company® has encountered an extensive set of roof strata challenges and has overcome various drilling issues by varying machine parameters and working with customers and tool manufacturers to develop solutions. Every mine wants to drill and install roof bolts as fast as possible with maximum safety at the lowest possible installation cost for their conditions. In most circumstances, the intuitive method of higher speeds and pressures can actually have a detrimental effect on the roof drill safety and performance.This paper will outline recent tests carried out at several different coal mines in the Eastern United States. The tests focused on optimizing the drilling parameters of feed pressure, feed rate, rotation speed, and drill torque.The drill feed, rotation speed, and rotation torque, as well as the type of bit selected, have a definite impact on the performance of the roof drill including drilling speed, safety, and tool life. The drilling process can be improved while also improving operator safety and reducing bolt installation costs by maintaining the appropriate roof drill settings for the specific strata conditions.The advantages of improving the drilling process includes increased bit life, increased drill steel life, reduced hanging drill steels, reduced clogging of the vacuum system, decreased whipping drill steel potential, reduced noise generation, and increased cutting size which reduces fine dust generation and dust collection system servicing.INTRODUCTIONIn recent times, the economic pressures that coal producers are facing have created an increased emphasis on controlling operating costs. Several coal operators have pointed out their dissatisfaction with low bit life, and there is a renewed interest in improving tool life and machine performance as part of an overall cost control strategy. Operators are looking for ways to reduce tooling cost, maintenance costs, and drill downtime without decreasing drill performance. This renewed interest in reducing operating costs, along with the ongoing desire to improve safety, created a perfect environment to take a fresh look at the existing fleet of machines to see what could be accomplished. The goal was to take a practical approach to reviewing machine parameters to determine what changes could be made. The emphasis was on changes that would be feasible to roll out to an entire fleet of machines in a short period of time with minimal capital expenditure. The thought process was that significant improvements could be made by simply tuning up the machine parameters to provide a more efficient and safer bolting process."

Jan 1, 2015

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By Stephen C. Tadolini

Effective barrier pillar design is an essential component for safe and productive underground coal mining. Barrier pillar design methodologies that incorporate sound engineering judgment have been used for practical everyday usage. The next logical step is to utilize numerical modeling techniques that help combine practical experience and empirical observations into barrier pillar design analysis. A case study is presented that describes the barrier pillar design process, but also highlights the importance of considering the global mine response by evaluating: adjacent pillar stabilities, impact of intersection and entry widths, capacity of primary and secondary bolting systems and rib stabilization used for the safe and efficient removal of the longwall face equipment.

Jan 1, 2013