Search Documents

By Werner Bilfinger, Claudio Nahas, Marcelo Waimberg

"INTRODUCTION The so called Porto Maravilha Project consists of the re-urbanization of a 500 ha area in the Rio de Janeiro port region. Several changes in local infrastructure are being implemented, including a significant change in the road system, with the demolition of the former “Via Perimetral” viaduct and construction of 4 new tunnels: • Saúde tunnel - 35 m long (Waimberg et al, 2014); • “Binária tunnel” - 1012 m long; • “Via Expressa” twin tunnels - 1850 m long each way. The tunnels were excavated almost completely in rock using conventional drill and blast methodology and only some short stretches in weathered rock, associated to faults zones, residual soils and marine sediments close to the tunnel portals. During excavation of access shaft and “Via Expressa” and “Binária” tunnels significant ground settlements as well as settlements of buildings founded both on shallow and deep foundations were measured. These values could not be associated to conventional tunneling induced settlement troughs. This paper focuses on the “Via Expressa” tunnels, presenting a brief description of the project as a whole, its geological and geotechnical background, monitoring results, and a discussion of possible causes of the measured settlements. PROJECT DESCRIPTION The Porto Maravilha Project is an integrated multidisciplinary action on behalf of the Rio de Janeiro city council with support from the State and Federal Governments. In addition to creating new conditions for working, housing, transport, culture and leisure for the resident population, it also promotes expressive economic development in the region (Portonovo, 2015). Porto Maravilha Project is carrying out actions for the recovery of the region’s historical heritage, as well as promoting the population´s social and economic development. One of the main benefits of the Porto Maravilha Project is the construction of the new traffic system in the port area, consisting of the Express and Binário roadways. The new project, which will replace the current Perimetral Rodrigues Alves viaduct system, will increase traffic flow capacity by 27%."

Jan 1, 2016

In recent years, Computational Fluid Dynamics, CFD, has been commonly utilized in the mining industry to model the fluid flow behavior in underground mine workings. This paper uses CFD modeling to simulate the airflow behavior in underground crosscut regions, where brattice sails are used to direct the airflow into these regions. Brattice sails are cost effective ventilation control devices for temporary or permanent use in underground mining. They can be used to deflect air into the unventilated areas such as crosscut regions. Their design and installation is a fundamental issue for maintaining a sufficient supply of fresh air and achieving effective air circulation and contaminant removal. At the same time, they should have little impact on the mine ventilation system. This paper presents the results of a two-dimensional CFD model, which examines the effects of brattice length on fluid flow behavior in the crosscut regions. The results of this study will assist in understanding the ventilation air behavior and in determining the optimum size of brattice curtain (sails), which provide a highly effective contaminant removal from the unventilated mine areas. This, in turn, helps the mine ventilation designers to meet the mine safety requirements.

Jan 1, 2009

By H. Polat, Q. Hu, S. Chander

The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l%, however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent.

Jan 1, 1992

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By M. K. Larson

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment, and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. But this efficiency also comes at a cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impacts of underlying assumptions in each method is essential to proper use of results in mine design. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health

Jan 1, 2009

By J. K. Borchardt

The use of statistical design to optimize deinking process design has been studied for the flotation deinking of newspapers. The interactions of two variables are often important in determining flotation deinking efficiency. The interactions can be synergistic or antagonistic. These interactions would not be discovered using the traditional method of varying one parameter and holding the other variables constant. An experiment design in which two or more process parameters are varied simultaneously is required to identify these interactions. A considerable number of conclusions could be drawn about the relative importance of process variables on ink particle size distribution, ink removal efficiency, and flotation yield loss in a flotation deinking process. However, these findings could be influenced by the deinking surfactant and the ink chemistry.

Jan 1, 2001

By Georgy Cherkashov, Svetlana Babaeva, Tamara Stepanova, Firstova. Anna

Seafloor massive sulfides (SMS) study in the Russian Exploration Area at the northern equatorial Mid Atlantic Ridge began after signing the contract with International Seabed Authority in 2012. In order to evaluate the SMS resources in the course of exploration the major and rare metals with economic value should be determined. The evaluation is based on geochemistry and mineralogy and particularly on the type of rare metals occurrence in the SMS. As a case study research of the Semyenov cluster of SMS deposits have been conducted.

Sep 1, 2014

By Fulvio Tonon

And Rabcewicz said ?tunnels should be driven full face whenever possible.? ADECO, which stands for ?Analysis of Controlled Deformations in tunnels,? now allows us to fulfll Rabcewicz?s dream in any stress-strain condition. In order to achieve that dream and its consequent control over cost and schedule, however, NATM must be abandoned for the ADECO. The paper presents the basic concepts in the ADECO approach to design, construction and monitoring of tunnels together with some case histories, including: full face excavation for Cassia tunnel (width of 22 m, height of 14 m) in sands and silts under 5 m cover below an archeological area in Rome, Italy; Tartaguille tunnel (face area > 100 m2) advanced full face in highly swelling and squeezing ground under 100 m cover where NATM led to catastrophic failure, France; and 80 km of tunnels (face area > 100 m2) advanced full face in highly squeezing/swelling ground under 500 m cover for the high-speed railway line between Bologne and Florence, Italy (turnkey contract).

By Deborah McCombe

-Canadian Regulators -Qualified Person -Professional Association -Resources & Reserves -Foreign Codes -Disclosure of Historical Resources -Issues in Application of Resources & Reserves -Industry Best Practices developed by CIM -Technical Report and Reserves and Resources -Summary

Jan 1, 2003

By M. Ge

Pattison Mine is a small sandstone mine located in Iowa. The sandstones produced by the mine are not common construction and aggregate materials. The stones are used to produce a special type of sand for hydraulic fracturing, a critical technique for recovering tight gas and shale gas. These sandstones are very different from the minerals and rocks which have been studied extensively in mining. On the one hand, they are brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, they are friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, a research program was set up by the mine and Missouri University of Science and Technology. This paper discusses the preliminary results of this investigation.

Jan 1, 2012

Global mining company achieves significant productivity gains with three-dimensional (3D) mine models developed with Abaqus finite element analysis software. In a steep change beyond traditional processes, Abaqus finite element analysis (FEA) software from Simulia (the Dassault Systèmes? brand for realistic simulation), is being used to enhance mine design and engineering simulation at a number of major mines around the world. In North and South America, Africa and Australia some of the world?s biggest mining companies are applying FEA technology to evaluate safety and improve design planning, implementation and operations. Beck Arndt Engineering (BAE), a Sydney-based international consultancy, is a pioneer in the commercial development of engineering solutions for the mining industry. The consultancy has worked closely with engineers at Simulia Australia to expand the use of Abaqus FEA simulation software for mining applications. Among the early adoptors of mine-ready FEA technology is the world?s largest miner, BHP Billiton. With BAE?s help, BHP has already applied this technology to evaluate mines in Canada and Australia. At the BHP Billiton Nickel West Perserverance Deeps Project in Western Australia, Abaqus FEA software is now being used to help engineer the safety and productivity of planned deep-mining operations. To achieve this goal in the deep-mining environment significant technological innovation is required. Using measurements of site deformation and seismicity, Abaqus FEA models have been calibrated and, in a single day, used to simulate a full, 3D, inelastic analysis of a mine?s life cycle. In recent years, similar applications at Debswana?s Jwaneng Mine in Botswana, the Newcrest Mining Ridge-way Deeps Project in New South Wales, Australia and Rio Tinto?s Argyle Diamond mine in Western Australia have also established Abaqus FEA analysis as the lead-ing technology for multi scale, simulation-aided mining engineering. Joop Nagtegaal, a pioneer of FEA and a Dassault Systèmes Corporate Fellow, said that Abaqus FEA software is unique in its capabilities to enable mining engineers to investigate design innovations from the drawing board to full production. ?In the design stage, Abaqus models, which include rockmass volumes spanning several kilo-meters around the ore body and down to excavations just a few meters across, are used to compare and optimize engineering options,? Nagtegaal said. ?Then, as the mine goes into production, large volumes of data from the field are incorporated with the analysis models to allow them to be calibrated to a precision not previously available to the mining industry.?

Jan 1, 2009

By W. L. Hollinshead, Alwin Poltinger

GENERAL Tunneling by hand digging is as old as the history of humans. Mechanized tunneling did not begin to replace manual methods until around the beginning of the 19th century(Brunel patent, 1818). It brought with it a higher degree of safety for the workers and a much higher rate of boring. But for any kind of tunneling, an accurate and feasible method of survey must be accomplished during mining. That means, that for each tunnel project the most efficient survey method must be devised. The method to be defined depends on the spatial curve, diameter, speed of tunneling method, purpose of tunnel and contractual accuracy. The final accuracy of a finished tunnel is heavily dependent upon three critical elements: 1. Quality of the above ground survey 2. Tunnel traverse and directional transfer from above ground 3. Guidance for the mining job. Combining The Survey And The Guidance System Since the guidance system (GS) is one of the critical factors in the determination of the tunnel final accuracy, it is necessary to analyze how the directional control and tunnel traverse measurements can be effectively integrated into a GS. Any guidance system, whether manual or high technology, must continually detect and compensate for movement of its theodoliteor laser station standpoint. Movement beyond a preset allowable amount must generate a warning or error message to the user. Additionally, optical refraction can interfere with the results. Refraction will have an effect on any kind of optical GS. Therefore, careful selection of target and standpoint locations can minimize, but not completely eliminate, the influence of refraction. Some GS technologies, such as Gyro-based systems, are immune to the effects of refraction, but have other, methodical errors which will be described later in this paper. GUIDANCE Overview Why is a guidance system necessary? A GS, whether manual or automatic, compares the design direction and slope of a tunnel with the current position of the mining

Jan 1, 1997

By JESSICA W. A. AZURE, Kansake A. Bruno, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

Blasting generates undesirable ground vibration with adverse effects on humans, the environment, and structures. Numerous studies have used various techniques including machine learning (ML) to predict the peak particle velocity (PPV) caused by blasting in surface mines. These studies used the validation-set approach to evaluate the performance of their predictive models. In this study, Random Forest (RF), Gaussian Process (GP), and Gradient Boosting Machine (GBM) were applied for the prediction of PPV using data from a large open-pit gold mine in Ghana. An ensemble model based on a stacked generalization approach was then built on these three base models to significantly improve the PPV prediction performance. The model evaluation was done using repeated tenfold cross-validation which resolves the challenges with the validationset approach for small datasets. The dataset used in this study comprised a total of 196 measurements taken from different blasting operations. R-squared ( R2 ), mean absolute error (MAE), and root mean square error (RMSE) were used to evaluate the model performance. The results obtained from these models revealed that all the base models did not significantly outperform each other. However, the stacked generalization approach had a better performance, with RMSE = 0.12, R2 = 0.96, and MAE = 0.07. This approach presented an improvement over the existing methods and will be useful for highly accurate predictions of ground vibration during blast design. The application of this model will be useful for efficient and effective blast design.

Nov 8, 2022

By D. A. Lindsey

Gravel lithology affects the quality of aggregate because different rock types in gravel have different physical and chemical properties. The lithologic composition of alluvial gravel reflects the composition of its source terrane and the variable effects of weathering and transport on each rock type. This report discusses lithologic controls on aggregate quality in the mountain-front environment of the Colorado Front Range. Lithologic controls on aggregate quality of gravels were evaluated using pebble count data. Gravel lithology along the Front Range shows both temporal and regional variation. The principal variable in gravel lithology is quartz plus quartzite, of which quartzite is commonly more abundant. Large quantities of metaquartzite derived from the mountain front southwest of Boulder, Colo., were dispersed northeastward during deposition of the oldest Front Range gravels. Average quartz plus quartzite is greatest in the oldest gravels. Aggregate quality is probably enhanced by large quantities of quartzite. Abundant volcanic rocks in gravel may enhance aggregate quantity, but such occurrences are local in extent. Abundant sedimentary rocks in gravel, mainly sandstone near the mountain front, may decrease aggregate quality.

Jan 1, 2002

By J. Geyer, B. T. Burton, H. W. Newcomen

For open pits developed in tropical climates the upper portions of the pit walls are often located in residual soils and weathered rock. Due to the presence of relict structures, and the relatively low strength of the residual soils and weathered rock, design slope angles in these materials have to be developed by blending the results of kinematic assessments of geologic structures with rock mass stability analyses and traditional soil mechanics. Background information on the engineering considerations of residual soils are discussed, and the results of geotechnical assessments for proposed pit design of the Brisas del Cuyuni Project, located in southeastern Venezuela, are presented.

Jan 1, 2000

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

By Paul L. Russell

Interest in the western oil shales of the US began in about 1908, with the first retort in Colorado constructed in 1917. The most successful early developments were near Elko, NV, where the Catlin Shale Products Co. produced more than 1.9 dam3 (12 000 bbl) of shale oil during 1920-1924 and at Rulison, CO, where a US government operation produced about 570 in 3 (3 600 bbl) of shale oil during 1926-1929. Plentiful low-cost crude oil was developed about this time and shale oil was of little or no interest until after World War II. From 1944 to about 1972, several companies, and the US government, operated shale oil mines and recovery plants in Colorado. While technical successes were achieved and an estimated 40-56 clam' (250 000-350 000 bbl) of shale oil were produced, economics were not favorable and commercial production was not achieved. In recent years domestic production of crude oil supplies has not kept pace with US consumption. The growing shortfall has been met with imports. The cost of imported oil has continued to escalate and increased US dependence on petroleum imports are national concerns, because of the negative impact on US balance of payments and an increasing dependence on other nations for US energy needs. In 1978, petroleum imports equaled about 44% of demand, up from 23% in 1970, but down from 48% in 1977 because of availability of Alaskan North Slope crude oil. Reduced domestic consumption and other factors have reduced current imports to about 40-45% of de¬wand-but at ever increasing cost. The growing shortage of crude petroleum and its increasing cost have resulted in renewed worldwide interest in oil shales. In the past, the main obstacle to oil shale development (progress toward commercial production) has been economics-shale oil cost too much to develop and thus could not compete with conventional petroleum crudes. Even with today's inflated energy prices, some experts say the production of synthetic crude oil from oil shale is, at best, marginally economic. The 1973-74 Arab oil embargo and increased crude oil costs-along with the federal government's offer to lease oil shale lands-resulted in renewed

Jan 1, 1981

By W. Pawlos, A. Bakalarz, M. Duchnowska

This paper presents the results of an investigation into the influence of hydrodynamics on a preflotation process for the copper sulfide ore from the Fore-Sudetic Monocline deposits in Poland in a flotation machine. The main aim of the preflotation stage for Polish copper ore is to remove the easy-to-float organic matter — organic carbon — that causes serious problems in metallurgical processes. The organic matter is connected with the presence of shale ore. This paper describes the preflotation experiments conducted to investigate the effect of various stirrer speeds. The upgrading selectivity of copper and organic carbon were analyzed and compared. The results show that the effectiveness of separation between organic carbon and copper decreases with increased stirrer speed in the laboratory flotation machine. The more intensive the mixing of the flotation suspension, the lower the selectivity of the preflotation experiment. Lower stirrer speed probably provides lower mechanical entrainment and flotation of copper minerals.

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013